Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop T-Bucket Windshields At Speedway Motors

Everything a roadster enthusiast needs for T-Bucket windshield installation is at Speedway Motors. Find everything from windshield frames, windshield wing nuts, glass setting channels, wind wing kits to brackets, and windshield rubber. To finish the installation, make sure you get vintage T-Bucket windshield support rods and posts.

"T-Bucket, Windshields and Glass" Page 1 of 5

  • 1915-31 Ford Windshield Swivel, Stainless
    1915-31 Ford Windshield Swivel, Stainless
    x
                

    These windshield swivels are for 1915-1931 Fords with round tubing windshield frames.

    Ford Windshield Swivel

    • Sold each
    • Stainless finish

    Windshield Mount Guide (GIF)

  • Universal Wind Wing Brackets
    $79.99
    Product Rating: 5.00 Stars
    Universal Wind Wing Brackets
    x
                

    Universal wind wing brackets for most 1930-1935 Fords and others. Fully chrome plated.

    Designed to screw into windshield posts. Brackets only. Set of four. Glass not included.

    • 5/16" fine thread
    • Main body (or wing): 2-15/16"
    • From bottom mounting face to tip of main mounting body: 1-3/8"
  • Aluminum Windshield Slug Material With Holes, 9 Inch
    Aluminum Windshield Slug Material With Holes, 9 Inch
    x
                

    Aluminum windshield slug material designed for Speedway's round tube "T" style windshields.  This slips inside the tubing to allow you to attach hinges, glass clips and the frame to the posts.  9" long, drilled and tapped for hinges and glass caps.

    • Designed for round tube "T" style windshields
    • 9 Inch Long
    • Pre-Drilled and Tapped for Hinges and Glass Caps
  • Square Top T Windshield Frame, 39-5/8 Inches Wide
    Square Top T Windshield Frame, 39-5/8 Inches Wide
    x
                

    Mr. Roadsters square top 'T' windshield frames fit most fiberglass T-buckets. Triple chrome plated steel. Kit includes frame (approximately 20" tall), non-functional hinges and hardware. Designed for short style posts.

    No glass or windshield rubber is included with our windshield frames.

    Note: Speedway 1923-25 Model T Bodies use a 39-5/8" wide windshield frame when using short posts.

    Builder's Tip: If using 1/4" glass or lexan, use urethane or setting tape (available from a glass shop) and do not use brass setting channel.

  • 1915-25 Model T Laid Back Short Windshield Posts
    1915-25 Model T Laid Back Short Windshield Posts
    x
                These short style Model T windshield posts are laid back 30° for a more racy look. They are made of Stainless Steel and include mounting bosses on back side to permit a smooth, clean installation. Fits our 1923-25 T-bucket bodies but can be used on others with a little fitting.
            
  • Aluminum Windshield Slug for Model T, 3-1/2 Inch Long, 2 Hole
    Aluminum Windshield Slug for Model T, 3-1/2 Inch Long, 2 Hole
    x
                

    Aluminum windshield slug material designed for Speedway's round tube "T" style windshields.  This slips inside the tubing to allow you to attach hinges, glass clips and the frame to the posts.  3.5" long, 2 holes drilled and tapped for hinges and glass caps.

    • Aluminum construction
    • Fits Speedway round tube "T" style windshields
    • 3.5" long
    • 2 holes drilled and tapped for hinges and glass caps
  • Lexan Wind Wings with Holes
    $35.99
    Lexan Wind Wings with Holes
    x
                

    Replacement Lexan wind wings for your universal wind wing kits. 

    • These are 16" tall by 5 7/8" wide
    • Thickness: 3/16"
    • Center to center of the two sets of mounting holes on the wind wings is 6 ¾"
    • One set of holes is 3" from the end of the wing and the other set is 6 ¼"
    • Total of 16" in length or height of the wind wing


     

  • One-Piece Round Top Model T Windshield for Angled Posts, 14 x 39-5/8 Inch
    One-Piece Round Top Model T Windshield for Angled Posts, 14 x 39-5/8 Inch
    x
                Mr. Roadster is the nation's largest builder and supplier of superior  windshield frames! Fits most 'T' bucket bodies. No hinges or rubber  divider required. Easy installation. All parts are triple chrome plated. 14" tall. Designed for short style vertical (916-56231) or 30° angled posts (715-1111).
    • Glass and windshield rubber not included 
    • If using 3/16" glass or lexan, use with brass setting channel. 
    • If using 1/4" glass or lexan, use urethane or setting tape (available from a glass shop) and do not use brass setting channel.

    Note: Speedway's 1923-25 Model T bodies use a 39-5/8" wide windshield frame when using short posts.

  • Model T Windshield Rubber, h Style
    Model T Windshield Rubber, h Style
    x
                

    These windshield rubber gaskets are not supplied with our windshield frames, so you will need to order one of each. The "h" style fits between two pieces of top and bottom glass. Fits 1/4" glass. Fits 1909-1927 Model T.

    Windshield Rubber Image (GIF)

  • 1922-1925 Tall Style Model T Windshield Posts, Aluminum
    1922-1925 Tall Style Model T Windshield Posts, Aluminum
    x
                

    These reproduction cast aluminum posts (unpolished finish) are a one piece design which measures approx. 26" from bottom-to-top.

    1922-1925 Model T Windshield Posts

    • Tall Style
    • Aluminum, natural finish 
    • Requires drilling to mount

    Note: The windshield mounts at a 30 degree angle and the center hole of the swivel pocket is approx. 2-1/2" down from the top of posts.

    T-Bucket Windshield Frame Diagram/Tech Tip (Link)

  • 1923-25 Model T Windshield Frame, Chrome
    1923-25 Model T Windshield Frame, Chrome
    x
                

    Mr. Roadster '23-'25 Model T steel windshield frames are reproductions using the stock dimensions: bottom 38-1/2 " wide, 10-1/8" tall, top 37" wide, 10-1/4" tall. Includes slugs and glass caps. Channel kit is sold separately. No glass or windshield rubber is included with our windshield frames.

    Builder's Tip: Speedway '23-'25 T bodies use a 39-5/8" wide windshield frame when using short posts. If using 3/16" glass or lexan, use with brass setting channel.  If using 1/4" glass or lexan, use urethane or setting tape (available from a glass shop) and do not use brass setting channel.

  • 1923-25 Model T Windshield Frame, Plain
    1923-25 Model T Windshield Frame, Plain
    x
                

    Mr. Roadster '23-'25 Model T steel windshield frames are reproductions using the stock dimensions: bottom 38-1/2 " wide, 10-1/8" tall, top 37" wide, 10-1/4" tall. Includes slugs and glass caps. Channel kit is sold separately. No glass or windshield rubber is included with our windshield frames.

    Builder's Tip: Speedway '23-'25 T bodies use a 39-5/8" wide windshield frame when using short posts. If using 3/16" glass or lexan, use with brass setting channel.  If using 1/4" glass or lexan, use urethane or setting tape (available from a glass shop) and do not use brass setting channel.

  • 1915-22 Model T Roadster Windshield Frame, Plain
    1915-22 Model T Roadster Windshield Frame, Plain
    x
                

    Mr. Roadster 1915-22 Model T steel round top windshields are exact reproductions using the stock dimensions: 39-1/8 " wide, 10" tall top and 12-1/8" tall bottom.  Channel kit sold separately. No glass or windshield rubber is included with these windshield frames.

    Builder's Tip: If using 3/16" glass or lexan, use with brass setting channel. If using 1/4" glass or lexan, use urethane or setting tape (available from a glass shop) and do not use brass setting channel.

  • Model T Glass Cap, Brass
    $3.99
    Model T Glass Cap, Brass
    x
                

    Stock style glass caps fit all Model T windshields.

    Sold each.

    Model T Glass Cap Illustration (GIF)

  • 1926-27 Model T Roadster Windshield Frame, Bottom Only, Plain
    1926-27 Model T Roadster Windshield Frame, Bottom Only, Plain
    x
                

    These beautiful replacement '26-'27 Model T windshield frames are available as a complete frame kit or just the bottom section to fit a specific application. These are 7/8" O.D. and the glass channel is 5/16" wide and 1/4" deep. The lower part of the frame next to the body accepts our T seal number 555-92600 and the slot for the seal is 1/8" wide with provision to accept the "T" style seal. 

    No glass or windshield rubber included with our frames. The slugs that are included with this windshield frame must be positioned, drilled and tapped by the installer.

    • 35" wide at bottom of frame
    • 38-1/2" overall width
    • 9-3/4" tall

    NOTE: You will also need (4) studs, wing nuts, and swivels (all sold separately) along with this frame.

  • 1913-14 Ford Model T Brass Glass Setting Channel for Open Cars
    1913-14 Ford Model T Brass Glass Setting Channel for Open Cars
    x
                Fits Ford Model T Roadster and Touring open top applications. Designed to use 3/16" thick safety glass or Lexan. Channel holds glass in the original frames.
            
  • 1932-36 Ford Windshield Swivel for Square Tubing Frame, Chrome
    1932-36 Ford Windshield Swivel for Square Tubing Frame, Chrome
    x
                

    These windshield frame cone swivels will work perfect for your 1932-1936 Fords with square tubing windshield frames.

    • 1932-36
    • Ford Square Tubing Windshield Frames
    • Mount these at pivot point of stanchion
    • Available in die cast chrome
    • Sold each

    Windshield Mount Guide (GIF)

  • 1909-22 Ford Model T Roadster Windshield Hinges, Functional, Polished Brass
    1909-22 Ford Model T Roadster Windshield Hinges, Functional, Polished Brass
    x
                

    Windshield frame hinges for 1909-22 Model T Ford Roadster windshields.

    NOTE: Functional hinges have a mounting stud for windshield support rods. Functional hinges only pivot/function when the pivot assembly is forward or to the front of the windshield frame. These become a non-functional 2-piece design when the pivot assembly is installed to the rear or behind the windshield frame.

    911-13101 Instructions (PDF)

  • One-Piece Round Top Model T Windshield Frame, 39 Inches Wide
    One-Piece Round Top Model T Windshield Frame, 39 Inches Wide
    x
                Mr. Roadster is the nation's largest builder and supplier of superior windshield frames. Fits most 'T' bucket bodies. No hinges or rubber divider required. Easy installation. All parts are triple chrome plated. 20" tall. Designed for short style posts (916-56231 or 916-56232). 
    • Glass and windshield rubber not included 
    • If using 3/16" glass or lexan, use with brass setting channel. 
    • If using 1/4" glass or lexan, use urethane or setting tape (available from a glass shop) and do not use brass setting channel.

    Note: Speedway's 1923-25 Model T bodies use a 39-5/8" wide windshield frame when using short posts.

  • 1926-27 Model T Roadster Windshield Frame, Plain
    1926-27 Model T Roadster Windshield Frame, Plain
    x
                

    These beautiful replacement '26-'27 Model T windshield frames are available as a complete frame kit or just the bottom section to fit a specific application. These are 7/8" O.D. and the glass channel is 5/16" wide and 1/4" deep. The lower part of the frame next to the body accepts our T seal number 555-92600 and the slot for the seal is 1/8" wide with provision to accept the "T" style seal. 

    No glass or windshield rubber included with our frames. The slugs that are included with this windshield frame must be positioned, drilled and tapped by the installer.

    NOTE: You will also need (4) studs, wing nuts, and swivels (all sold separately) along with this frame.

  • 1915-25 Model T Short Style Windshield Posts, Plain
    1915-25 Model T Short Style Windshield Posts, Plain
    x
                

    Short style Model T posts are brass castings with mounting bosses on the back side to permit a smooth, clean installation. Fits 1915-25 Ford Model T roadster bodies.

    916-56232 Instructions (PDF)

  • 1909-22 Ford Model T Roadster Windshield Hinges, Non-Functional, Plain
    1909-22 Ford Model T Roadster Windshield Hinges, Non-Functional, Plain
    x
                

    Windshield frame hinges for 1909-22 Model T Ford Roadster windshields.

    NOTE: Functional hinges have a mounting stud for windshield support rods. Functional hinges only pivot/function when the pivot assembly is forward or to the front of the windshield frame. These become a non-functional 2-piece design when the pivot assembly is installed to the rear or behind the windshield frame.

    911-56400 Instructions (PDF)

  • Square Top T Windshield Frame, 40-1/2 Inches Wide
    Square Top T Windshield Frame, 40-1/2 Inches Wide
    x
                

    Mr. Roadsters square top 'T' windshield frames fit most fiberglass T-buckets. Triple chrome plated steel. Kit includes frame (approximately 20" tall), non-functional hinges and hardware. Designed for short style posts.

    No glass or windshield rubber is included with our windshield frames.

    Note: Speedway 1923-25 Model T Bodies use a 39-5/8" wide windshield frame when using short posts.

    Builder's Tip: If using 1/4" glass or lexan, use urethane or setting tape (available from a glass shop) and do not use brass setting channel.

  • Two-Piece Round Top Model T Roadster Windshield Frame, 39 Inch Wide
    Two-Piece Round Top Model T Roadster Windshield Frame, 39 Inch Wide
    x
                

    Mr. Roadsters 2-piece round top windshield frames fit most fiberglass T-buckets. Triple chrome plated. Kit includes frame (approximately 20" tall) and hardware. Designed for short style windshield posts.

    No glass or windshield rubber is included with our windshield frames. Note: Speedway's 1923-25 T bodies use a 39-5/8" wide windshield frame when using short posts.

    Builder's Tip: If using 1/4" glass or lexan, use urethane or setting tape (available from a glass shop) and do not use brass setting channel.

  • 1926-27 Model T Roadster Windshield Frame, Chrome
    1926-27 Model T Roadster Windshield Frame, Chrome
    x
                

    These beautiful replacement '26-'27 Model T windshield frames are available as a complete frame kit or just the bottom section to fit a specific application. These are 7/8" O.D. and the glass channel is 5/16" wide and 1/4" deep. The lower part of the frame next to the body accepts our T seal number 555-92600 and the slot for the seal is 1/8" wide with provision to accept the "T" style seal. 

    No glass or windshield rubber included with our frames. The slugs that are included with this windshield frame must be positioned, drilled and tapped by the installer.

    NOTE: You will also need (4) studs, wing nuts, and swivels (all sold separately) along with this frame.

  • 1932-36 Ford Windshield Swivel for Square Tubing Frame, Stainless Steel
    1932-36 Ford Windshield Swivel for Square Tubing Frame, Stainless Steel
    x
                

    These windshield frame cone swivels will work perfect for your 1932-1936 Fords with square tubing windshield frames.

    • 1932-36
    • Ford Square Tubing Windshield Frames
    • Mount these at pivot point of stanchion
    • Available in die cast stainless steel
    • Sold each

    Windshield Mount Guide (GIF)

  • Wind Wing Brackets
    $54.99
    Product Rating: 5.00 Stars
    Wind Wing Brackets
    x
                Replacement wind wing brackets for your universal wind wing kits.  
            
  • 1909-1912 Model T Roadster Brass Windshield Frame, Torpedo
    1909-1912 Model T Roadster Brass Windshield Frame, Torpedo
    x
                

    Mr. Roadster '09-'12 Model T windshield frames are constructed from solid brass, then fully polished. Features a brass channel. No glass or windshield rubber is included with these windshield frames. 

    Builder's Tip: If using 3/16" glass or lexan, use with a brass setting channel. If using 1/4" glass or lexan, use urethane or setting tape (available from a glass shop) and do not use a brass setting channel.

  • 1926-1927 Speedster Vee Windshield Frames, Polished Brass
    1926-1927 Speedster Vee Windshield Frames, Polished Brass
    x
                

    Unique, classic-stye 3-piece design made of cast brass. Fits 1926-1927 Model T roadsters for an original look. Also for use on the Speedway Track-T Roadster kit. Windshield glass (not included) easily siliconed into the milled grooves. Glass template included.

  • 1909-1912 Model T Roadster Brass Windshield Frame, Speedster
    1909-1912 Model T Roadster Brass Windshield Frame, Speedster
    x
                

    Mr. Roadster '09-'12 Model T windshield frames are constructed from solid brass, then fully polished. Features a brass channel. No glass or windshield rubber is included with these windshield frames. 

    Builder's Tip: If using 3/16" glass or lexan, use with a brass setting channel. If using 1/4" glass or lexan, use urethane or setting tape (available from a glass shop) and do not use a brass setting channel.

  • Threaded Windshield Studs
    $3.99
    Threaded Windshield Studs
    x
                

    Studs are zinc plated for longevity. Not included in our windshield kits. Sold each.

     Windshield Mount Guide

  • 1915-31 Ford Windshield Swivel, Brass
    1915-31 Ford Windshield Swivel, Brass
    x
                

    These windshield swivels are for 1915-1931 Fords with round tubing windshield frames.

    Ford Windshield Swivel

    • Sold each
    • Brass finish

    Windshield Mount Guide (GIF)

Goto Previous PagePrevious Page
1 2 3 4 5