Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products

Let Speedway Motors "Steer" you in the right direction with the right steering components for your T-Bucket! From steering U-joints from Sweet Mfg. to the top steering columns and drop mounts from Ididit, we've got the best parts at the best prices around. Don't forget to add a Speedway Motors aluminum steering wheel for the feel behind the wheel that can't be duplicated.

Featured Products
Sweet Mfg Steering U-Joint, 3/4 Inch Round to 3/4 Inch Round, Universal
Sweet Mfg Steering U-Joint, 3/4 Inch Round to 3/4 Inch Round, Universal
x
            

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering u-joints available. Made by Sweet Manufacturing. These steering universal joints have 3/4 weld-on ends.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing
  • Features needle bearing u-joints
  • U-Joint=3.875" L x 1.375" D

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

 

Sweet Mfg Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
Sweet Mfg Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
x
            Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. This universal joint is 3.875 inches long and 1.375 inches in diameter.
  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing
  • Features needle bearing u-joints
  • U-Joint=3.875" L x 1.375" D
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Steer Clear Steering Box Drop, Brushed Finish
Steer Clear Steering Box Drop, Brushed Finish
x
            

Finally, a solution to the age old steering column/pedals problem. This nifty box provides unlimited options for steering shaft clearance so a high performance engine and headers will fit. Allows you to safely reposition the steering column higher, giving you more room for your feet and pedals.

  • Chain driven action
  • Improved road feel versus typical U-joint setups
  • Mounts on the inside or outside of your firewall
  • Four reinforced through-holes assure a strong, secure installation
  • Uses common 3/4"-36 spline U-joints and couplers
  • 4-1/2" wide X 1-1/2" thick(less shafts) X 4" longer than offsets

Available in 8", 10", 12", 14" or 16" offsets.

2006 Best Engineered New Product at SEMA

Nostalgia Steel Steering Column
From: $89.99
Product Rating: 4.73 Stars
Nostalgia Steel Steering Column
x
            

We now have an affordable steel version of our famous hot rod steering column. The 1-3/4" black painted column still has a quick release steel hub that accepts the common 3-bolt Grant steering wheel pattern and uses common 3/4" DD u-joints. 15 gauge mild steel.

910-32311 Instructions (PDF)

"T-Bucket, Steering" Page 1 of 12

  • Sweet Mfg. 001-21040 Rack and Pinion Replacement Boot
    Sweet Mfg. 001-21040 Rack and Pinion Replacement Boot
    x
                

    These high quality rubber replacement boots for Sweet Mfg. rack and pinions perform as good as they look.

    • Replacement for Sweet Mfg. rack and pinion
    • High quality rubber construction

     

  • Speedway Vega Style Steering Box Combo, All New Assembly
    Speedway Vega Style Steering Box Combo, All New Assembly
    x
                

    Speedway Motors makes it easy to bolt together a cross steering system with our Vega Steering Box Combo kit. Kit includes a Speedway Vega box, steel pitman arm, and a Ford Model T - 1934 frame mount. This steering box accepts a 5/8" 36-spline U-joint or coupler.

    Kit includes:

    • Speedway Vega Steering Box
      • 20:1 steering ratio
      • 5 turns lock-to-lock
    • Steel Vega Pitman Steering Arm
      • Plain finish 
      • Non-offset design
      • Double-tapered "Ford" tie rod end hole (lets you attach the drag link on the top or on the bottom)
    • Vega Steering Box Mount
      • Fits Model T thru 1934 Ford frames
      • Weld-on design
  • Grant 5891 Steering Wheel Puller Kit
    Grant 5891 Steering Wheel Puller Kit
    x
                

    These Grant 3 bolt steering wheel pullers are to be used for pulling original wheels or previously installed Grant wheels from the steering shaft.

    • Easy to use
    • Includes all bolts/hardware necessary
  • Hoop Style Steering Arm, Ford Spindle
    Hoop Style Steering Arm, Ford Spindle
    x
                

    Hoop style steering arm features boss for 7° tapered tie rod end, but can be drilled for 5/8" rod end. Available for 1937-48 Ford car spindle  applications.

    Steering Arm End Chart (GIF)

  • Reversed Corvair Steering Box
    $379.99
    Product Rating: 4.60 Stars
    Reversed Corvair Steering Box
    x
                

    If you have tried to find a good used Corvair steering box, you know that the chances of finding a good one are slim to none. Don't bother! These brand new Corvair steering boxes have already been reversed. Designed for use on traditional steering cars and T-buckets, these boxes are constructed of modern high strength steel and needle bearings to ensure durability, which original boxes just can't offer. 

    Painted black. Does NOT include pitman arm. Ratio is 20:1.  

    Parallel Steering Set-Up Guide (GIF)

  • Sweet Mfg Steering U-Joint, 3/4 Inch Round to 3/4 Inch Round, Universal
    Sweet Mfg Steering U-Joint, 3/4 Inch Round to 3/4 Inch Round, Universal
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering u-joints available. Made by Sweet Manufacturing. These steering universal joints have 3/4 weld-on ends.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • U-Joint=3.875" L x 1.375" D

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

     

  • 1/4 Inch Quick Release Ball Lock Dowel Pin, Steel Body, 1-1/2 Inch Grip
    1/4 Inch Quick Release Ball Lock Dowel Pin, Steel Body, 1-1/2 Inch Grip
    x
                

    These quick-release push-button pins offer you the ultimate in quick-release fastening. They are made of high-grade steel and feature a gold iridited finish for durability. A steel quick release pin for any application. Choose 1-1/2" grip.

    Quick Release Ball Lock Dowel Pin

    • Steel Body
    • 1-1/2 Inch Grip
    • 1/4 Inch pin diameter
  • Chrome Braided Hose Covering Kit
    Chrome Braided Hose Covering Kit
    x
                Over 20 feet of stainless steel braided hose cover with chrome plated hose end covers! 

    Easy to install! Easy to clean! Hi-tech detailing at an economy price. Each dress kit contains 3' of vacuum line, 4' of fuel line, 12' of heater hose, and an extra long 4-1/2' of radiator hose sleeving, and 4 shrink sleeves for vacuum lines, 4 fuel line fittings, 4 heater hose fittings, 2 fittings for upper radiator hose.

    Note: The covering is not the actual hose. 

  • Aluminum Male AN10 O-Ring to AN10 Adaptor
    Aluminum Male AN10 O-Ring to AN10 Adaptor
    x
                

    Male O-ring to AN. Steel or aluminum.

    AN Thread Size Guide (GIF)

    Fitting Thread Application Chart (GIF)

  • AFCO 30321 Steering Support Bearing
    AFCO 30321 Steering Support Bearing
    x
                Self-aligning bearing can be installed in firewall or mid-plate to support steering shaft 
            
  • Performance Tool W80650 GM Lock Plate Tool
    Performance Tool W80650 GM Lock Plate Tool
    x
                  If you have a GM Steering column and need to get at the switches, you will need this tool. Compresses the lock plate so snap ring can be removed.   
            
  • 1937-48 Ford Steering Arms, 3-3/4 Inch Drop
    1937-48 Ford Steering Arms, 3-3/4 Inch Drop
    x
                

    These forged steel steering arms will attach to all 1937-48 Ford spindles but their greater drop, 3-3/4" from spindle mount holes means they work best on 1935-48 Ford cars (with spring-over front axle). Clears most radius rods and wishbones. These steering arms accept 11/16" Ford 7 degree "tapered" tie rod ends (both the top and bottom are tapered to allow tie rods to mount above or below arm as needed). You can drill-through with a 5/8" bit to use spherical rod ends.

    Use a 46" eye-to-eye tie rod link when used with a 48" wide axle with Ford spindles.

    Steering Arm Ends Guide (GIF)

    Cross Steering Guide (GIF)

  • Sweet Mfg Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    Sweet Mfg Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    x
                Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. This universal joint is 3.875 inches long and 1.375 inches in diameter.
    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • U-Joint=3.875" L x 1.375" D
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    Sweet Mfg Chrome Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • 1.354" not including the screws (1.534" including), width on the u-joint.
    • 1.125" OD on the ends not including the nut (1.345" including the nut). 

    Steering U-Joints and Couplers Application Chart (GIF)

    Steering Box/Rack/Spline Chart (Link)

    Spline Size (Link)

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Universal Shift Indicator Housing, Chrome
    Universal Shift Indicator Housing, Chrome
    x
                Universal shift indicator housings. Works with 3 speed or overdrive lens and pointer.
            
  • Speedway Corvair Pitman Arm
    From: $49.99
    Product Rating: 4.50 Stars
    Speedway Corvair Pitman Arm
    x
                

    This is our forged 'new design' Corvair pitman arm. It measures approximately 7" end to end, approximately 5-3/8" from the center of the big hole to the center of the small hole. The arm has a side-to-side offset approximately 1-7/8". The small hole fits an early Ford tie rod end (such as our 910-02909) and it is half tapered from both sides so that the drag link can be mounted from either side.


     

     

  • Ididit 2400300010 Steering Column Band Swivel Lower Mount, 1-3/4 Inch
    Ididit 2400300010 Steering Column Band Swivel Lower Mount, 1-3/4 Inch
    x
                

    Mounting your steering column to the firewall or floor can be a real challenge. Ididit's steel band swivels are an easy and inexpensive solution.

    446-4030 Instructions (PDF)

  • Vega Pitman Arm - Tapered for Tie Rod
    From: $49.99
    Product Rating: 5.00 Stars
    Vega Pitman Arm - Tapered for Tie Rod
    x
                These all new reproduction pitman arms feature a non-offset design, a double tapered "Ford" tie rod end hole (lets you attach the drag link on the top or on the bottom), and comes in gleaming stainless steel or plain steel. Perfect for a repro Vega steering box. 
            
  • 15 Inch Pro-Grip Aluminum Steering Wheel, Dish
    15 Inch Pro-Grip Aluminum Steering Wheel, Dish
    x
                

    Super lightweight 15" Pro-Grip aluminum steering wheels feature three spokes and have both 1/4" and 5/16" bolt mounting holes. Pro-Grip wheels have BIG 1-1/4" diameter rims allowing for a firm, comfortable grip. The welded finger nubs on the back are spaced 1" apart for additional grip.

    Has a 3" dish.

  • Standard GM 5-Position Tilt Steering Column, 32 Inch Long, Chrome
    Standard GM 5-Position Tilt Steering Column, 32 Inch Long, Chrome
    x
                These 5-position tilt columns are for those who want great  performance   at affordable pricing. Made from steel 2" tube. Standard 1"  DD output   shaft. Column accepts any 1969-94 GM car steering wheel or  aftermarket   adapter.
    • Chrome plated finish
    • 32" length
    • Floor shift applications
    • 1" DD output shaft
    • Standard GM wiring and plug
    • Includes tilt, turn and hazard levers/knob

    Be sure to include Painless Wiring's GM steering column pigtail kit (91064039) with your order for an easier installation.

  • 15 Inch Standard Dish Aluminum Steering Wheel
    15 Inch Standard Dish Aluminum Steering Wheel
    x
                Super lightweight 15" aluminum wheels feature three spokes and have both 1/4" and 5/16" bolt mounting holes. This standard grip wheel has a smaller 7/8" diameter rim.
            
  • 1937-48 Ford Steering Arms, 1-3/4 Inch Drop
    1937-48 Ford Steering Arms, 1-3/4 Inch Drop
    x
                

    These 1-3/4" drop forged steel steering arms are popular on Model T - 1934 Fords with 4" dropped axles and four-bar or hairpin radius rod suspensions. Will attach to '37-'48 Ford spindles and accept 11/16" Ford "tapered" tie rod ends (both the top and bottom are tapered to allow tie rods to mount above or below arm as needed). You can drill-through with a 5/8" bit to use spherical rod ends.

    Use a 46" eye-to-eye tie rod link when used with a 48" wide axle with Ford spindles.

     Steering Arm Ends Guide (GIF)

     Cross Steering Guide (GIF)

  • Nostalgia Steel Steering Column
    From: $89.99
    Product Rating: 4.68 Stars
    Nostalgia Steel Steering Column
    x
                

    We now have an affordable steel version of our famous hot rod steering column. The 1-3/4" black painted column still has a quick release steel hub that accepts the common 3-bolt Grant steering wheel pattern and uses common 3/4" DD u-joints. 15 gauge mild steel.

    910-32311 Instructions (PDF)

  • Sweet Mfg Steering U-Joint, 5/8-36 Spline, 3/4 DD, Vega/Corvair/GM Rack
    Sweet Mfg Steering U-Joint, 5/8-36 Spline, 3/4 DD, Vega/Corvair/GM Rack
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature full compliment bearings and a 5/8"-36 spline.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 5/8"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Speedway Classic Solid Spoke 13 Inch Black Steering Wheel - No Holes
    Speedway Classic Solid Spoke 13 Inch Black Steering Wheel - No Holes
    x
                

    Smooth black cushion with chrome spokes. Has the common 3 bolt pattern mount.  These wheels feature rubber grips and are made of steel.  Chrome cap is included.

    • Smooth black cushion
    • 3 bolt pattern mount
    • Steel
    • Chrome cap included

    Note: These steering wheels require addtional purchase of a horn button retainer, not included with steering wheel.  We offer our corresponding retainer (41010112) and various adapter kits for your specific application. 

     

  • Speedway Vega Cross Steering Box
    Speedway Vega Cross Steering Box
    x
                

    The Vega Manual Steering Box is the foundation of a cross steering system, which is the most popular steering system for modern Hot Rods. These boxes are compact, durable and are getting more scarce every day. 

    This unit bolts up to all normal Vega-type brackets and accepts Vega-spline u-joints, pitman arms and accessories. Durable cast iron and machined steel construction will give years of high-mileage service.

    • New castings and components
    • Faithful reproduction of size, shape and mounting hole locations
    • No core charge

    Cross Steering Guide (GIF)

    Note:  Vega steering box is not adjusted at the factory and therefore, it is necessary that the steering box be adjusted upon installation per the instructions as provided on the PDF instruction sheet.

    910-32204 Instructions (PDF)

  • U-Joint, 5/8"-36 Spline to 3/4" Round Weld-On
    U-Joint, 5/8"-36 Spline to 3/4" Round Weld-On
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. This steering universal joint is the highest quality for racing or street use.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 5/8"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • 3/4 O.D. Solid Steel Steering Shaft
    From: $12.99
    Product Rating: 5.00 Stars
    3/4 O.D. Solid Steel Steering Shaft
    x
                These solid steering shafts are made for you to cut to fit. 3/4" O.D. 1018 solid steel shaft. Available in 24", 36", 48", 60" and 72" lengths. 

    Steer Shaft Application Chart

  • U-Joint, 3/4" Round Weld-on To 3/4 DD
    U-Joint, 3/4" Round Weld-on To 3/4 DD
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints have a 3/4 round weld-on end.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • U-Joint=3.875" L x 1.375" D
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

     

  • Stainless Steel Tie Rod End, 11/16-18 RH
    Stainless Steel Tie Rod End, 11/16-18 RH
    x
                These tie rod ends are just like our standard Ford tie rod ends except they are made of beautifully polished stainless steel. They have 11/16"-18 thread and include hardware. Make sure to use anti-seize on the threads. 
            
  • Grant 502 Classic Cruisin 3-Spoke Steering Wheel, 13-1/2 Inch
    Grant 502 Classic Cruisin 3-Spoke Steering Wheel, 13-1/2 Inch
    x
                

    The Grant Classic Cruisin' steering wheel features a smooth, high gloss black cushion and chrome spokes that made it popular during the 1960's. The gloss vinyl grip was extremely popular on dune buggies and hot rods of that era. 13-1/2" diameter, 3" dish.

    Requires installation kit (sold separately) to mount this wheel to your specific steering column. 

    410-502 Instructions (PDF)

  • Grant 201 Classic Wood Steering Wheel, 15 Inch
    Grant 201 Classic Wood Steering Wheel, 15 Inch
    x
                

    The timeless, wood-rimmed 3-spoke steering wheel has been used on cars since the beginning of the automobile int he early 1900s. This Classic Wood wheel from Grant features hand-polished walnut hardwood rims with anodized aluminum rivet construction and chrome spoke centers. Includes chrome horn button cover.

    Requires installation kit which includes the horn switch (sold separately) to mount this wheel to your specific steering column.

    410-201 Instructions (PDF)

Goto Previous PagePrevious Page
1 2 3 4 5 ... 12