Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products

Nobody knows T-Bucket brakes like Speedway Motors! With the most experience in the T-Bucket brakes business, you can be assured that you are getting quality components for the most critical part of your car from top brands like Wilwood and AFCO . Speedway has disc and drum brake kits that are sure to provide the stopping power you need. We also have a huge selection of master cylinders, brake rotors, brake bleeders and brake pedals, plus the brake lines, fittings and proportioning valves you need to complete any brake system rebuild or upgrade.

"T-Bucket, Disc Brakes and Accessories" Page 1 of 8

  • Disc Brake Kit, 1978-88 GM Caliper to Early Ford Spindle, 5 on 4-1/2 Inch
    Disc Brake Kit, 1978-88 GM Caliper to Early Ford Spindle, 5 on 4-1/2 Inch
    x
                

    Easily installs 11" rotors and the 1978-up GM Metric calipers to your 1937-48 Ford passenger car and 1937-47 1/2 ton Ford spindles. No machine work needed. This kit works well with bolt-on steering arms. The 11" rotor brake kits are great for street rods based on 1932-48 Fords. Uses Ford/Mopar wheel bolt pattern of 5 on 4-1/2".

    910-31945 Instructions (PDF)

  • GM Metric Disc Brake to 9 Inch Ford Bracket Set
    GM Metric Disc Brake to 9 Inch Ford Bracket Set
    x
                Allows you to bolt '78 an Up GM Metric disc brakes on Ford 9" rearend.  Hardware sold separately.

    Includes:
    • 2 Caliper brackets
    • 2 Adapter plates
    • 2 Spacer plates
    • 8 5/16" spacers
    • 8 1/8" spacers

    Note:  This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts.  If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so.  Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

  • Weld-On 1978-88 GM Flat Mount Caliper Bracket
    Weld-On 1978-88 GM Flat Mount Caliper Bracket
    x
                

    These caliper brackets mount flat and must be welded onto your 3" diameter axle tube. Designed to mount a 1978-1988 GM metric car front caliper for use with an 11.75" diameter rotor. Brackets are 1/4" thick.

    IMCA APPROVED

  • Ford 9 Inch Bolt-On Rear Disc Brake Kit
    Ford 9 Inch Bolt-On Rear Disc Brake Kit
    x
                

    If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM metric style calipers, brake pads and hardware.

    • Fits both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
    • For Ford passenger car axles ONLY 
    • Fits axle with maximum flange diameter of 6-1/4" O.D.
    • For 15" and larger wheel applications ONLY

    NOTE: This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts. If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so. Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

    Axle Flange Identification Chart (GIF)

    910-31902 Instructions (PDF)

  • Weld-On 1978-88 GM Metric Caliper Bracket
    Weld-On 1978-88 GM Metric Caliper Bracket
    x
                

    Mounts 1978-1988 GM front caliper to any 3" tube rear end using 11-3/4" diameter rotors. Fully machined steel with punched lightening holes. Measures approximately 5-1/2" between mounting holes.

    IMCA APPROVED

  • Disc Brake Kit 1978-88 GM Caliper to Early Ford Spindle, 5 on 4-3/4 Inch
    Disc Brake Kit 1978-88 GM Caliper to Early Ford Spindle, 5 on 4-3/4 Inch
    x
                

    Easily install 11" rotors and 1978-88 GM Metric calipers to your 1937-48 Ford passenger car style spindles with no machine work needed. This disc brake kit is great for street rods based on 1932-1948 Fords. For lightweight cars like T-buckets or early roadsters, we recommend the Wilwood kits. This front disc brake conversion kit works well with bolt-on steering arms. The 11" diameter rotors have the GM wheel bolt pattern of 5 x 4-3/4". Calipers have 7/16"-20 inlets.

    910-31946 Instructions (PDF)

  • Replacement 11-1/4 Inch Rear Brake Rotor
    Replacement 11-1/4 Inch Rear Brake Rotor
    x
                

    These 11-1/4" one-piece, vented iron disc brake rotors are for rear disc brake applications. Features dual bolt patterns for 5 x 4.5" (Ford/Mopar) and 5 x 4.75" (Chevy/GM) wheels. 

    • Center Hole:  2.78"
    • Backspace:  2.30"
    • Maximum Axle Flange Diameter:  6-1/4"
    • Thickness:  1"
    • Thickness @ Center of Rotor:  0.236"
  • Airheart Brake 175H, Hard Lining Replacement
    Airheart Brake 175H, Hard Lining Replacement
    x
                

    Brake "pucks" or caliper pads for your vintage Airheart 175H series calipers. Pucks sold each.

    • Measures 1-5/8" O.D.
    • Has an inside step approx 1-1/2" O.D.
    • There are (2) countersunk screw holes in the pad for attachment.
    • Hard - Used on aluminum & steel rotors. The best pad to use on aluminum rotors. Very little metallic. Longer rotor & pad life. Excellent street pad.
  • Airheart Brake 175H, Medium Lining Replacement
    Airheart Brake 175H, Medium Lining Replacement
    x
                

    Brake "pucks" or caliper pads for your vintage Airheart 175H series calipers. Pucks sold each.

    • Measures 1-5/8" O.D.
    • Has an inside step approx 1-1/2" O.D.
    • There are (2) countersunk screw holes in the pad for attachment.
    • Medium - Used on steel. Medium friction works well at lower temperatures. Good for street or dirt use.
  • Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake
    Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake
    x
                

    If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM emergency brake calipers, brake pads and hardware.

    • Fits both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
    • For Ford passenger car axles ONLY 
    • Fits axle with maximum flange diameter of 6-1/4" O.D.
    • For 15" and larger wheel applications ONLY

    NOTE: This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts. If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so. Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

    Axle Flange Identification Chart (GIF)

    910-31921 Instructions (PDF)

  • Weld-On 1969-77 GM Flat Mount Caliper Bracket
    Weld-On 1969-77 GM Flat Mount Caliper Bracket
    x
                

    These caliper brackets mount flat and must be welded onto your 3" diameter axle tube. Designed to mount a 1969-1977 GM mid-size car front caliper for use with an 11.75" diameter rotor. Brackets are 5/16" thick.

    IMCA APPROVED

  • Speedway 10 Inch Hybrid Brake Rotor for Pinto
    Speedway 10 Inch Hybrid Brake Rotor for Pinto
    x
                

    5/8" Studs Installed - All coarse threads are quick start style. 

    Our new 10" hybrid rotor is designed to fit the Pinto spindle. Complete with inner and outer races and 5/8" studs. Pre-drilled holes include 5 on 5" bolt circle spacing.

    This brake rotor is designed for dirt track applications and should NOT be used for asphalt racing.

     

  • Weld-On 1969-77 GM Mid-size Caliper Bracket
    Weld-On 1969-77 GM Mid-size Caliper Bracket
    x
                

    Mounts 1969-1977 GM mid-size car front caliper to any 3" tube rear end using 11-3/4" diameter rotors. Fully machined steel with punched lightening holes. Measures approximately 7" between mounting holes.

    IMCA APPROVED

  • Speedway Soft Street Brake Pads, GM Metric 1978-UP
    Speedway Soft Street Brake Pads, GM Metric 1978-UP
    x
                

    Speedway soft brake pad for GM Metric 1978-Up.

    Sold as one set of 4 (ST); outfits two calipers.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side.

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Wilwood 150-8936K BP-10 GM Metric 1978-Up Brake Pads
    Wilwood 150-8936K BP-10 GM Metric 1978-Up Brake Pads
    x
                

    Speedway Motors is your one-stop shop for GM 1978-Up Midsize caliper brake pads.

    • Medium friction, smooth engagement, low abrasion on iron rotors.
    • Flat torque curve.
    • Low to medium wear rate, increases as temperature increases.

    Brake Pad Brochure (PDF)

    Tech Tip:  Only use full metallic pads on coated rotors.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side. 

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Wilwood 140-11013 1937-1948 Ford Heavy Duty Disc Brakes
    Wilwood 140-11013 1937-1948 Ford Heavy Duty Disc Brakes
    x
                

    Wilwood Forged Dynalite Pro-Series Front Hub Kits offer a complete disc brake upgrade solution for your 1937-48 Ford spindles. Based on the venerable forged billet Dynalite caliper, these versatile kits suit the braking requirements and style preferences for a daily driver, serious competition, or the most discriminating show enthusiast.

    Most kits require no modifications for installation, and provide plenty of clearance inside popular 15” wheels. FDL Pro-Series kits can be used with either manual or power boost master cylinders.

    Wilwood Heavy Duty Kits Feature:

    • Forged 4-piston Dynalite Calipers
    • 11.00" diameter Ultralite HP 30 Vane iron rotors - plain finish
    • Wilwood BP-10 SmartPads - low noise, low dust
    • Lightweight anodized aluminum Pro Street hubs
    835-14011013 Instructions (PDF)

    *NOTE*: See Notes tab for important install info.

  • 11 Inch GM Brake Rotor with Ford Bolt Pattern
    11 Inch GM Brake Rotor with Ford Bolt Pattern
    x
                

    1973-1977 GM rotor redrilled to the 5 x 4-1/2" Ford bolt pattern. To be used with our #7024475 GM metric caliper adapter kit for disc brakes on a 1937-1948 Ford car spindle. Very common rotor to use as a conversion rotor. Has 1/2" fine wheel studs.

    NOT interchangable with rotor 91031066. If you have brackets and adapters designed for the Granada rotor, use part #91031066.

  • Airheart Brake 3025-9002 175 x One QC Caliper O-Ring Overhaul Kit
    Airheart Brake 3025-9002 175 x One QC Caliper O-Ring Overhaul Kit
    x
                

    Repair parts for Airheart disc brake calipers are hard to find! These O-ring overhaul kits will get you back on the track in a hurry. Each kit includes all neccessary parts for a rebuild.

  • Basic Brake Kit 1978-88 GM Caliper to Early Ford Spindles
    Basic Brake Kit 1978-88 GM Caliper to Early Ford Spindles
    x
                Easily installs 11" rotors and the 1978-up GM Metric calipers to your 1937-48 Ford passenger car spindles. No machine work needed. Please see below for suggested 1973-77 GM type 11" brake rotor part #'s required.

    Kit Includes:
    • GM to Ford brake brackets
    • 1978-Up hardware
    • Bearing and seal adapters
    • Seals
    • Inner bearing cups
    • Inner bearing cones
    • Spacers
    • Instructions
    • Does not include dust caps, washers or spindle nuts

    This kit works well with bolt-on steering arms. The 11" rotor brake kits are great for Street Rods based on 1932-48 Fords. However, for or a T bucket or early roadster, you might consider the Wilwood kits shown below.

    702-4475 Instructions (PDF)

  • Weld-On Rear Disc Brake Kit, 1969-77 GM Caliper, 3 Inch Backspace
    Weld-On Rear Disc Brake Kit, 1969-77 GM Caliper, 3 Inch Backspace
    x
                

    Replace those old drum brakes with modern rear disc brakes. Steel rotor hat mounts .81" x 11-3/4" Pro-lite vented iron rotors and calipers to 3" tube rear end.  Complete with rotors, hats, calipers (7/16"-20 inlets), brackets, brake pads, caliper brackets and slider bolts. 

    Hat fits 5 lug hubs with 4-1/2", 4-3/4", or 5" bolt circle.

    910-31936 Instructions (PDF)

  • Replacement Carbon Steel Brake Rotors
    Replacement Carbon Steel Brake Rotors
    x
                For use on our spindle mount wire wheels. Bolts to back side of spindle mont wheels. Rotors are made from 3/16" carbon steel, and are 10" in diameter. These rotors are ground for flatness and have been clear zinc plated.
            
  • Stainless Steel Drilled Brake Rotor for Spindle Mount Wheel
    Stainless Steel Drilled Brake Rotor for Spindle Mount Wheel
    x
                

    For extra stopping power and good looks. Bolts to the back side of spindle mount wheels. Brake rotors are shown here polished.

    • 10" O.D.
    • 3/16" thick
    • The center hole diameter is 2.691"
    • The bolt pattern contains four 5/16" holes on a 3.375" circle
  • Wilwood 140-2111-B Rear Brake Kit - Olds/Pontiac, 2.81 Offset
    Wilwood 140-2111-B Rear Brake Kit - Olds/Pontiac, 2.81 Offset
    x
                

    Wilwood FDL Pro-Series rear disc brake kits provide a complete solution for the uncommon Olds/Pontiac rear axles on applications where parking brake assemblies are not required. Forged billet Dynalite four piston calipers, two-piece hat and rotor assemblies, and high friction pads provide optimized and balanced braking for all types of customized applications.

    • Piston Area (in²): 3
    • 1/8" NPT inlet
    • Minimum Wheel Diameter (in): 15
    • BP-10 Smart pads

    These kits do not have emergency brake provisions.

    Dynalite Rear Axle Kit Installation Instructions (PDF)

    Exploded Installation Schematic 

    Kit fits some 15" wheels. Check wheel clearance diagram in kit installation instructions before purchase.

    Axle Flange Identification Chart 

  • Wilwood 140-7675 1964-74 GM Front Disc 12.19 Inch Big Brake Kit
    Wilwood 140-7675 1964-74 GM Front Disc 12.19 Inch Big Brake Kit
    x
                

    Need a big brake package that can scrub off serious speed and look great doing it?Wilwood's Forged Dynalite Pro-Series Front Hub Kits offer complete disc brake upgrade solutions for traditionaldisc brakespindle applications onclassic Chevymuscle cars. All kits can be used with manual or power boost master cylinders.

    12.19" Big Brake Series features:

    • Forged 4-pistonDynalite Calipers - black finish
    • 12.19" diameter Ultralite HP 32 Vane rotors - plain finish
    • Wilwood BP-10SmartPads - low noise, low dust
    • Lightweight anodized aluminum Pro Street hubs
    • Minimum wheel diameter of 16"

    All kits include calipers, hubs, rotors, brackets and hardware needed. Brake hoses sold separately.

    835-1407675 Instructions (PDF)

     

  • GM 10 & 12 Bolt Bolt-On Rear Disc Brake Kit
    GM 10 & 12 Bolt Bolt-On Rear Disc Brake Kit
    x
                

    If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This complete kit includes two bolt-on caliper brackets, two 11-1/4" vented rotors, two GM metric style calipers, brake pads and hardware.

    • Rotors have both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
    • Fits axle with a maximum flange diameter of 6-1/4" O.D.
    • 2.780" rotor center hole
    • Does not fit all 10 & 12 bolt axles. Check Application tab for details. 

    Axle Flange Identification Chart (GIF)

    910-31919 Instructions (PDF)

  • Wilwood 140-2117-B Rear Brake Kit - Mopar/Dana Axle, 2.36 Offset
    Wilwood 140-2117-B Rear Brake Kit - Mopar/Dana Axle, 2.36 Offset
    x
                

    Wilwood FDL Pro-Series rear disc brake kits provide a complete solution for the popularMopar/Danarear axles on applications where parking brake assemblies are not required. Forged billet Dynalite four piston calipers, two-piece hat and rotor assemblies, and high friction pads provide optimized and balanced braking for all types of customized applications.

    • Ultralite HP 32 Curved Vane Vented Rotor - 12.19" x .810"
    • Forged billet Dynalite four-piston calipers
      • Piston Area (in²): 3
      • 1/8" NPT inlet
    • Minimum Wheel Diameter (in): 15
    • BP-10 Smart pads
    • Aluminum mounting brackets and hardware

    This kit will fit Mopar 8 3/4" and Dana 60 rear axlesequipped with green non-adjustable bearings (Mopar P/N RP400). These kits do not have emergency brake provisions.

    Wilwood Rear Brake Kit Installation Instructions (PDF)

    Axle Flange Identification Chart

    Exploded Installation Schematic

  • AFCO 7250-0200 Complete Rear Disc Brake Kit, 2-1/2 Inch Piston
    AFCO 7250-0200 Complete Rear Disc Brake Kit, 2-1/2 Inch Piston
    x
                Complete kit with standard GM metric calipers. Mounts vented rotors and calipers to 3" tube rearend. Complete with rotors, hats, calipers, brackets, brake pads and slide bolts. Hat fits 4-1/2", 4-3/4" and 5" bolt circle. 
            
  • Airheart Brake 3005-0000 150x1 Disc Brake Caliper
    Airheart Brake 3005-0000 150x1 Disc Brake Caliper
    x
                

    The Airheart 150x1 Series Disc Brake Caliper w/ Retracting Piston is designed to provide a maximum amount of braking power packed into a minimal amount of space for easy mounting. The 150x1 is typically used with spindle mount front wheels and is designed to be mounted in either the three or nine O'clock position on a disc. Either the caliper or disc must float.

    The 150X1 series features a single piston with a patented piston reactor. The body is made of die-cast aluminum alloy. Friction linings are available in both hard and soft materials.

    Requires type D.O.T. 3 brake fluid.

  • AFCO 7250-0300 Basic Rear Disc Brake Kit
    AFCO 7250-0300 Basic Rear Disc Brake Kit
    x
                Kits for metric calipers. These basic kits include brackets, steel vented rotors, hats and bolts. Caliper brackets weld to 3" tube rearend. Hat fits 4-1/2", 4-3/4" and 5" bolt circle. 
            
  • Wilwood 140-10996 1964-74 GM Front Disc 11 Inch Pro Series Brake Kit
    Wilwood 140-10996 1964-74 GM Front Disc 11 Inch Pro Series Brake Kit
    x
                

    Need a big brake package that can scrub off serious speed and look great doing it?Wilwood's Forged Dynalite Pro-Series Front Hub Kits offer complete disc brake upgrade solutions for traditionaldisc brakespindle applications onclassic Chevymuscle cars. All kits can be used with manual or power boost master cylinders.

    11.00" Pro Series Brakes feature:

    • Forged 4-pistonDynalite Calipers - black finish
    • 11.00" diameter Ultralite HP 30 Vane rotors - plain finish
    • Wilwood BP-10SmartPads - low noise, low dust
    • Lightweight anodized aluminum Pro Street hubs
    • Provides plenty of clearance inside popular 15” wheels.

    All kits include calipers, hubs, rotors, brackets and hardware needed. Brake hoses sold separately.

    835-14010996 Instructions (PDF)

     

  • Airheart Brake 121-3600 156 x Two Caliper O-Ring Overhaul Kit
    Airheart Brake 121-3600 156 x Two Caliper O-Ring Overhaul Kit
    x
                

    Repair parts for Airheart disc brake calipers are hard to find! These O-ring overhaul kits will get you back on the track in a hurry. Each kit includes all neccessary parts for a rebuild.

    • (4) O-rings 1-7/8" O.D. (cross section 1/8")
    • (2) O-rings 1-3/8" O.D. (cross section 1/16")

    150x1 Replacement Parts List (PDF)

  • Wilwood 140-2118-B Rear Brake Kit - New Big Bearing Ford, 2.5 Offset
    Wilwood 140-2118-B Rear Brake Kit - New Big Bearing Ford, 2.5 Offset
    x
                

    Wilwood FDL Pro-Series rear disc brake kits provide a complete solution for the popular Ford big bearing rear axles on applications where parking brake assemblies are not required. Forged billet Dynalite four piston calipers, two-piece hat and rotor assemblies, and high friction pads provide optimized and balanced braking for all types of customized applications.

    These kits do not have emergency brake provisions.

    835-1402118 Instructions (PDF)

    Axle Flange Identification Chart

  • Front Polished Stainless Steel Replacement Brake Rotor, 1/4 x 10 Inch
    Front Polished Stainless Steel Replacement Brake Rotor, 1/4 x 10 Inch
    x
                

    This replacement rotor is a 1/4" x 10" drilled brake rotor made for spindle mount front wheels. Bolts to back side of spindle mount wheels. Available in polished stainless steel finish.

    • Replacement rotor for spindle mount front wheels
    • 1/4" x 10" drilled rotor
    • Polished, stainless steel
  • Wilwood 120-1360 Mechanical Spot Caliper
    Wilwood 120-1360 Mechanical Spot Caliper
    x
                

    Wilwood caliper for use with mechanical pinion mounted emergency brake. Features a 2-position cam-actuated lever, aluminum construction, and a black anodized finish.

    • Max Rotor Width:  0.25"
    • Min Rotor Width:  0.18"
    • Max Rotor Diameter:  13"
    • Min Rotor Diameter:  6"
    • Mount Type:  Floating
    • Pad Area (in2):  0.9"
    • Pad Volume (in3):  0.31"
    • Caliper Mount Center:  2.95"
    • Caliper Weight:  1.2 lbs.
    • Caliper Dimension (Link)
    • Pad Dimensions (Link)
  • Wilwood 140-7143 Rear Disc Parking Brake Kit, Ford 9 Inch, 2.66 Offset
    Wilwood 140-7143 Rear Disc Parking Brake Kit, Ford 9 Inch, 2.66 Offset
    x
                

    Wilwood Dynalite rear brake kits combine high performance braking, high-tech style, and functional simplicity for rear axle disc brake conversions that require a parking brake. Whether it's a simple conversion from drum brakes, or an upgrade to compliment wheels, tires or suspension equipment, these kits have it all.  

    The emergency brake functions as a drum brake hidden within the mounting hat of the rotor for a clean installation. E-brake cables sold separately. Caliper has a 1/8" npt inlet.

    • Big 12.19" x .810" one-piece vented rotors
    • Rotors drilled to accept 5 on 4-1/2", 5 on 4-3/4" and 5 on 5" bolt patterns
    • Forged billet four-piston calipers
    • BP-10 Smart pads for a quick response and fade resistance
    • Aluminum mounting brackets
    • Includes all hardware

    835-1407143 Instructions (PDF)

    Axle Flange Identification Chart  (GIF)

  • Airheart Brake 175H x 1.62 Inch, Soft Lining Replacement
    Airheart Brake 175H x 1.62 Inch, Soft Lining Replacement
    x
                

    Brake "pucks" or caliper pads for your vintage Airheart 175H series calipers. Pucks sold each.

    • Measures 1-5/8" O.D.
    • Has an inside step approx 1-1/2" O.D.
    • There are (2) countersunk screw holes in the pad for attachment.

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Wilwood 140-7140 Rear Disc Brake Kit, Big Ford 9 Inch New 2-1/2 Offset
    Wilwood 140-7140 Rear Disc Brake Kit, Big Ford 9 Inch New 2-1/2 Offset
    x
                

    Wilwood Dynalite rear brake kits combine high performance braking, high-tech style, and functional simplicity for rear axle disc brake conversions that require a parking brake. Whether it's a simple conversion from drum brakes, or an upgrade to compliment wheels, tires or suspension equipment, these kits have it all.  

    The emergency brake functions as a drum brake hidden within the mounting hat of the rotor for a clean installation. E-brake cables sold separately. Caliper has a 1/8" npt inlet.

    • Big 12.19" x .810" one-piece vented rotors
    • Rotors drilled to accept 5 on 4-1/2", 5 on 4-3/4" and 5 on 5" bolt patterns
    • Forged billet four-piston calipers
    • BP-10 Smart pads for a quick response and fade resistance
    • Aluminum mounting brackets
    • Includes all hardware

    835-1407140 Instructions (PDF)

    Axle Flange Identification Chart  (GIF)

  • Weld-On Rear Disc Brake Kit, 1978-88 GM Caliper, 1.59 Inch Backspace
    Weld-On Rear Disc Brake Kit, 1978-88 GM Caliper, 1.59 Inch Backspace
    x
                

    Replace those old drum brakes with modern rear disc brakes. Mounts .81" x 11-3/4" Pro-lite vented iron rotors and calipers to 3" tube rear end. Complete with rotors, hats, metric calipers (7/16"-20 inlets), brackets, brake pads, caliper brackets and slider bolts.

    Hat fits 5 lug hubs with 4-1/2", 4-3/4", or 5" bolt circle.

    910-31932 Instructions (PDF)

  • GM 7.5 Inch 10 Bolt Bolt-On Rear Brake Kit w/ E-Brake
    GM 7.5 Inch 10 Bolt Bolt-On Rear Brake Kit w/ E-Brake
    x
                

    If you don't want to spend and arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes two bolt-on caliper brackets, two 11-5/8" vented rotors, two GM emergency brake calipers, brake pads and hardware.

    • 5 on 4-3/4" bolt circle
    • Fits over an axle with a maximum flange diameter of 6" O.D.
    • 2.872" rotor center hole
    • Requires the use of 16" wheels as this kit has a minimum 14-5/8" I.D. for caliper clearance 

    910-31928 Instructions (PDF)

  • Wilwood 140-2113-B Rear Brake Kit - Small Bearing Ford, 2.66 Offset
    Wilwood 140-2113-B Rear Brake Kit - Small Bearing Ford, 2.66 Offset
    x
                

    Wilwood FDL Pro-Series rear disc brake kits provide a complete solution for the popularFordsmall bearingrear axles on applications where parking brake assemblies are not required. Forged billet Dynalite four piston calipers, two-piece hat and rotor assemblies, and high friction pads provide optimized and balanced braking for all types of customized applications.

    These kits do not have emergency brake provisions.

    835-1402113 Instructions (PDF)

    Axle Flange Identification Chart

     

    Click Here for Exploded Installation Schematic

     

Goto Previous PagePrevious Page
1 2 3 4 5 ... 8