Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 50

Products

Air and Fuel Delivery

Shop T-Bucket Air & Fuel Delivery At Speedway Motors

Speedway Motors stocks all the best names in T-Bucket carburetors and intake manifolds! Plus, we have a great selection of fuel cells, as well as electric and mechanical fuel pumps. Don't forget to let your engine breath with filters from K&N and R2C. Speedway can fuel your need for speed!

Featured Products
  • Open 4 Barrel Carburetor Base Gasket
    Open 4 Barrel Carburetor Base Gasket
    (Part #55054)
    x
                Open base gaskets.
            
  • Sure Seal O-Ring Air Cleaner Spacer
    From: $4.99
    Product Rating: 4.91 Stars
    Sure Seal O-Ring Air Cleaner Spacer
    (Part #91011063)
    x
                

    This unique sealing ring spacer has O-ring on the carburetor side to prevent dust from entering past the filter base. Also allows you to raise the filter up for additional clearance.

    Available in three heights: 1/2", 1" or 2".

  • Aluminum Fuel Line, 3/8 Inch O.D.
    From: $10.99
    Product Rating: 4.73 Stars
    Aluminum Fuel Line, 3/8 Inch O.D.
    (Part #91011430)
    x
                Where else can you buy aluminum fuel line in the size and length you need? This easy-to-flare and bend tubing will save weight and money. 
    • Use with tube nut couplers, sleeves and 37° flared AN fittings
    • Rated to 250 psi
    • Not recommended for high pressure (brake) applications
    • Available in 10 ft., 20 ft., or 30 ft. coils

    Learn more about flaring lines and how to select proper automotive fittings by reading our tech article. The Principles of Automotive Fittings.

  • FST RPM350 Flo-Max High Performance Racing Fuel Filter System
    New
    FST RPM350 Flo-Max High Performance Racing Fuel Filter System
    (Part #910117350)
    x
                

    This fuel filter system from FST Performance was engineered to combine high efficiency fuel filtration in the smallest possible design. Its fuel flow capabilities and low fuel restriction make this the most innovative and efficient system built.

    • Will NOT separate oil from gas in 2-cycle engines.
    • The size and the clean custom look of the clear anodize make it the pick for high-end street rods and full race cars.
    • Billet 6061-T6 aluminum base/manifold
    • Ports: 4 multi-directional (2-IN & 2-Out) -8 AN (ORB) fitting ports. Also comes with -8 to -6 reducers.
    • Fuel Flow: 300 GPH
    • Filtration efficiency: 187sq. inches of 4 micron, water separating media
    • Burst: 250psi
    • Height: 4.75”
    • Width: 3”
    • Depth: 3.75”
    • Weight: 24 oz.
    • Base / manifold mounting holes: 7/16"
  • Fuel Filter Mounting Bracket
    Fuel Filter Mounting Bracket
    (Part #910117)
    x
                

    These fuel filter mounting brackets are CNC machined aluminum. Available in 1-3/8", 1-1/2", or 1-3/4" round tubing.

    These brackets are designed to be used with our filters. Hole is 2" inner diameter. 

  • K&N Engineering 81-0402 Inline Fuel Pump, 32 GPH, 4-7 PSI
    New
    K&N Engineering 81-0402 Inline Fuel Pump, 32 GPH, 4-7 PSI
    (Part #465810402)
    x
                

    This fuel pump from K&N provides premium quality fuel system hardware with a universal design that fits a wide variety of applications. This 12-volt pump helps prevent vapor lock and flooding. 

    • Compatible with diesel, biodiesel, gasoline, E85, methanol, ethanol, alcohol and other fuels
    • Universal design fits most applications
    • Pumps 32 gallons per hour between 4 and 7 psi
    • Self-priming design provides a quiet running volume
    • Eliminates vapor lock and flooding
    • Fuel filter and installation hardware is included
  • Speedway Fuel Cell Foam, 14 x 4 x 6 Inch
    Speedway Fuel Cell Foam, 14 x 4 x 6 Inch
    (Part #6007050)
    x
                

    Compatible with gasoline, E85, or alky fuels (not recommended for use with nitro-methane). This fuel cell safety foam keeps weight transfer/shift to a minimum, which provides you with more responsive and predictable handling. Can be cut and stacked as needed.

    • 8-12 gallon cells typically use 3-8 sticks
    • 16 gallon cells typically use 4-10 sticks
    • 22-32 gallon cells typically use 8-14 sticks

    Blocks are sold EACH.

  • Afco 4# Fuel Pressure Sending Unit (1/8 Inch Pipe)
    Afco 4# Fuel Pressure Sending Unit (1/8 Inch Pipe)
    (Part #10685284)
    x
                

    Afco 4# Fuel Pressure Sending Unit

    • 1/8 Inch Pipe

Filter

"T-Bucket, Air and Fuel Delivery" Page 1 of 50

Page 1 of 50

  • Edelbrock 1413 Performer 4 Barrel Carburetor, 800 CFM, Electric Choke
    Edelbrock 1413 Performer 4 Barrel Carburetor, 800 CFM, Electric Choke
    (Part #3251413)
    x
                

    Edelbrock Performer Series four barrel carbs have proven themselves to be easy to tune with great drivability. Whether you need to replace an aging stock carb or are looking for a performance carb to top off your hot rod, the Edelbrock Performer Series carbs are the best choice for performance and value. All Edelbrock products are proudly made in the U.S.A.

    Designed and calibrated for maximum street performance with most Performer RPM, RPM Air-Gap and Torker II manifolds and with Performer manifolds on large cubic-inch engines. Includes an electric choke and detailed instructions. Ford/Mopar throttle adapter arms sold separately.

    • Electric choke 
    • Smooth throttle response throughout the power band
    • Uses metering rods to transition between circuits - rods can be changed in seconds without carburetor removal or draining fuel
    • Float levels are factory set; adjustments are rarely needed
    • Change jets, adjust floats & replace needles/seats without draining fuel or removing carb
    • Lightweight all-aluminum body is compatible with gasohol and blended fuels
    • Includes both timed and full vacuum ports for ignition advance

    Edelbrock 800 CFM 4 Barrel Carburetor Installation Instructions (PDF)

     

  • Aeromotive 11140 340 Stealth Fuel Pump, Centered Inlet
    Aeromotive 11140 340 Stealth Fuel Pump, Centered Inlet
    (Part #91011140)
    x
                

    The Aeromotive 340 Stealth Fuel Pump is a high-output, in-tank, electric fuel pump that fits most popular EFI applications. It is a compact, lightweight pump that bolts into many existing hanger assemblies.

    What sets the 340 Stealth Pump apart is its superior flow throughout a wide pressure range. Compared to other popular aftermarket pumps, at 40 psi the 340 boasts more than 340 lph. That’s over 30% more flow, making it ideal for applications requiring more flow while retaining the factory lines and mounting provisions available in the OE configuration. The 340 is also perfect for use as a universal replacement for applications that require more flow to support forced air power adders such as turbo and supercharged applications.

    • Fits most vehicles where popular aftermarket pumps are applicable
    • Designed for in-tank use only
    • Can be used in carbureted or EFI applications
    • Turbine pump mechanism increases durability and can be used in pulse modulated applications

    910-11140 Instructions (PDF)

  • Kinsler Fuel Injection 5800 Spun Aluminum Tank, 2 Gallon
    Kinsler Fuel Injection 5800 Spun Aluminum Tank, 2 Gallon
    (Part #473500)
    x
                

    Beautiful, brush-finished .080" wall spun aluminum tank with a knurled, billet aluminum, non-vented screw-on cap. Two female 3/8" NPT fittings on top, one female 3/4" NPT fitting on the bottom.

    Mounting brackets sold separately.

  • Lokar XTCB-40RJ1 Midnight Series 502 Ram Jet Throttle Cable Bracket
    Lokar XTCB-40RJ1 Midnight Series 502 Ram Jet Throttle Cable Bracket
    (Part #491XTCB40RJ1)
    x
                
    • Brackets fit the GM ramjet engine.
    • These brackets along with Lokar Throttle Cables will allow the ramjet to work properly in any vehicle.
    • When used with an automatic transmission, be sure to use the transmission specific Lokar Kickdown Cable.
    • Uses TC-1000RJ throttle cable.
  • Fuel Pump Push Rod Bushing for 1949-53 Ford and Mercury Flathead V8
    Fuel Pump Push Rod Bushing for 1949-53 Ford and Mercury Flathead V8
    (Part #56052664)
    x
                

    These fuel pump push rod bushings for 1949-1953 Ford & Mercury Flathead V8 are 1-9/16" long.  They work perfect with our push rod (56052662).

    • Fuel pump push rod bushing
    • For 1949-1953 Ford & Mercury Flathead V-8
    • 1-9/16" long
    • For push rod (56052662)
  • Holley 0-80670 Avenger 670 CFM 4 Barrel Carburetor, Electric Choke
    Holley 0-80670 Avenger 670 CFM 4 Barrel Carburetor, Electric Choke
    (Part #42580670)
    x
                

    The Holley Street Avenger Model 4150 four barrel carb is the ultimate vacuum secondary street performance upgrade. This 4 barrel carb is street ready right out of the box and features a calibrated electric choke, air and fuel adjustments and built in fuel filters. There are clear sights for easy float adjustments, adjustable vacuum secondaries and four vacuum ports. Plus it has a million mile power valve, is 100% wet flow tested and includes fittings.

    • No Trouble quick change vacuum secondaries - up to 6% more acceleration or 5% better fuel economy with simple spring change (springs included) 
    • Vacuum secondaries allow use on wide variety of vehicles
    • Tuneable fuel metering system
    • Dual feed fuel inlet
    • 1 timed (spark) port, 2 full vacuum, and 1 PCV port
    • Ford A/T kickdown, does not work with A.O.D. transmissions
    • Calibrated for monster low-end torque, awesome acceleration, & unmatched top-end horsepower
    • Bolt on & go design
    • Electric choke

    Holley 670 CFM 4 Barrel Carburetor Installation Instructions (PDF)

  • OTB Gear 4660 Orbit Cast Spun Aluminum Air Cleaner
    New
    OTB Gear 4660 Orbit Cast Spun Aluminum Air Cleaner
    (Part #9104660)
    x
                

    This Orbit cast heavy aluminum spun air cleaner from OTB Gear has a truly unique look. The spun shell can be painted or clear coated.

    • Polished casting countersunk into heavy wall satin aluminum spinning
    • Outer shell can be painted or clear coated
    • Washable permanent filter
    • Fits standard 5" four bbl. Carb
    • Diameter 12" - height 4-1/2" 
    • Made in the USA

     

  • Edelbrock 5001 Small Block Chevy Torker II Intake Manifold
    Edelbrock 5001 Small Block Chevy Torker II Intake Manifold
    (Part #3255001)
    x
                

    Designed for 1955-86 high-performance 262-400 c.i.d. small-block Chevy V8s operating in the 2500-6500 RPM range. The Torker II is an updated version of original Torker offering better performance. Manifold accepts late-model waterneck, air-conditioning, alternator and H.E.I. distributor.

    Will fit Corvette and 1987 and later stock aluminum heads. Will NOT fit 1987 and later cast iron heads and will NOT cover port openings of Chevrolet Bowtie or LT1 heads.

    NOT intended for use on heavy vehicles (trucks, vans etc.).

    Torker II Intake Manifold Installation Instructions (PDF)

  • Speedway Aluminum Fuel Log for Demon Carburetor
    Speedway Aluminum Fuel Log for Demon Carburetor
    (Part #91011600)
    x
                

    Ensures adequate fuel pressure to carburetor and helps eliminate fuel starvation problems. Fuel pressure is regulated after carburetor has been supplied and not before. Must use return fuel line to take full advantage of benefits.

    Features AN8 inlet and two AN8 outlets.  Threaded 3/4" NPT (plugged) on back that can be used for a return line. Also has 1/8" NPT outlet for fuel pressure gauge, fittings sold separately. 

  • Speedway Holley Mechanical Fuel Pump Fuel Line Kit
    Speedway Holley Mechanical Fuel Pump Fuel Line Kit
    (Part #6174090)
    x
                

    This pump-to-carb fuel line kit will get you the -8 AN hose, hose end fittings and mechanical fuel pump fitting if required. Choose from push-on steel or aluminum fittings with blue hose, or aluminum fittings with stainless steel braided hose. Comes with -8 AN hose only.

    Fitting sizes listed indicate fuel pump outlet fitting size.

    Style Choice Guide:

    • ALU - aluminum fittings with blue hose
    • SS  - aluminum fittings with stainless hose
    • STL - steel fittings with blue hose 
  • Flamed Billet-Style Oval Air Cleaners
    Flamed Billet-Style Oval Air Cleaners
    (Part #91011037)
    x
                

    Theses highly polished aluminum air cleaners have the look of billet without the expense. Available with flame top.

    Measures 3" high, 8-3/8" wide. Fits 5-1/8" single quad air horns.

  • Edelbrock Big Block Chevy Dual Quad Set-Up, Rectangular Port
    Edelbrock Big Block Chevy Dual Quad Set-Up, Rectangular Port
    (Part #92519917)
    x
                

    There is nothing sweeter looking or sounding than a dual quad on a Chevy! This one kit gets you two manual choke Edelbrock carbs, an Edelbrock unpolished intake manifold, fuel line and special progressive linkage. Just add a suggested air cleaner to finish your installation.

    • 1500-6000 RPM
    • Will clear HEI distributors
    • Will not fit tall-deck truck blocks
    • Has 6-7/16" carb centers

    Overall Height from the bottom of the intake to the top of the air cleaners below:

    325-4237: 11.795"

    325-1235: 11.272"

    325-4119: 12.965"

    Height from bottom of intake to carb mounting surface: 4.899"

    • Port exit dimensions:  1.66" x 2.30

     

  • Sure Seal Air Cleaner Base Only, 14 Inch
    Sure Seal Air Cleaner Base Only, 14 Inch
    (Part #91011062-2)
    x
                

    Speedway's Sure Seal air cleaner base is manufactured from spun aluminum. Fits Holley carbs. Uses standard 14" diameter filters, sold separately. Minimum filter height required is 4".

    • Base has a 1-1/2" drop
    • Distance from the carb neck to top with .5" spacer and 4" filter = 4.25"

     

  • Nostalgia Spun Aluminum Air Cleaner
    Nostalgia Spun Aluminum Air Cleaner
    (Part #91011093)
    x
                This spun aluminum air cleaner fits common 5 1/8" neck 4BBL carburetors and is 8" diameter and 3 7/8" tall. Wing nut sold separately. 
            
  • Aluminum Neck with Flange and Cap
    Aluminum Neck with Flange and Cap
    (Part #6175023)
    x
                  Weld-in 2.3" O.D. bung. This aluminum filler neck bung includes a flange. Features vented cap which vents to the  underside of the cap.            
            
  • Aluminum Flare Fitting Plug, Blue, -16 AN
    Aluminum Flare Fitting Plug, Blue, -16 AN
    (Part #6176023)
    x
                

    Aluminum flare plugs. 37° AN.

    Fitting Thread Application Chart (GIF)

Goto Previous PagePrevious Page
1 2 3 4 5 ... 50