Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products

Speedway Motors stocks all the best names in T-Bucket carburetors and intake manifolds! Plus, we have a great selection of fuel cells, as well as electric and mechanical fuel pumps. Don't forget to let your engine breath with filters from K&N and R2C. Speedway can fuel your need for speed!

Featured Products
Rochester 2G Tri-Power Base Kit Without Linkage
Rochester 2G Tri-Power Base Kit Without Linkage
x
            

There's nothing cooler than a TriPower on your small block, but  the carbs are expensive and hard to find! With this kit you can use three junk yard 2G small base style Rochester carbs and put together a three deuce set-up for a fraction of the cost.

Includes two new bases for the secondary front and rear carbs, gaskets, jets, power valve and modified piston, idle tubes, plugs, hardware and new primary throttle shaft and butterflies. The center carb (primary) uses its stock base, and parts are included in the kit to modify your stock primary base.

This kit doesn't include an adjustable progressive linkage kit, but the linkage is available separately. 

Rochester 2 GC Tri-Power Carb Installation Instructions (PDF)

Three Chrome 9 Super 7   Carbs, 1957-86 Small Block Chevy Edelbrock Intake
Three Chrome 9 Super 7 Carbs, 1957-86 Small Block Chevy Edelbrock Intake
x
            

This tri power kit uses the Edelbrock C-357-B S/B Chevy 3x2 intake with Speedway's 9 Super 7® carbs. It has progressive linkage to give you good driveability and economy, but power when you need it. The manifold has a balanced 180° firing order port runner arrangement. It contains an exhaust gas heat riser and offers excellent performance potential. (idle-5500 rpm)

Kit includes three chrome plated carbs, the plain finish aluminum intake, 4" chrome air cleaners, linkage kit, chrome fuel block, fittings and red fuel line. Assembly required. Fits 1957-1986 Chevy 262-400 c.i.d. small-block Chevys.

9 Super 7® Linkage Instructions (PDF)

Note: Not applicable to an HEI based distributor system due to a clearance issue. This system must be used in conjunction with a small diameter based distributor.

The 9Super7 makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb set-up.

  • Three Deuce carburetor setups come with two "secondary" carbs for front and rear intake position and one "primary" carb for central/middle position
  • All-new tooling for crisp, flawless castings
  • New aluminum base assembly allows for cooler fuel temps and better fuel efficiency as compared to the original cast iron design
  • Stainless steel screws and hardware
  • Original troublesome needle and seat replaced by a Grose-style fuel inlet valve to better cope with higher fuel pressures and improved high speed running 
  • Will not stick or dribble like the old Viton-tipped needle and seat setups
  • Extended brass throttle shaft to simplify multi-carb linkage
  • Primary Carb - (1) Middle Position
    • Choke assembly, accelerator pump, and jets have all been faithfully retained and accept standard Stromberg parts
  • Secondary Carb - (2) Front and Rear Position
    • Special base plate with no idle circuits or choke linkage
    • Special butterflies and shafts installed
    • Works best with progressive linkage
    • Idle only off the center or main carburetor
    • No more plug foul

Note: The secondary carbs have NO choke, and they have NO idle system.

915-11655 Primary Carburetor Instructions (PDF)

Aluminum Socketless Reusable Push-On Hose Barb Ends for AN Fittings
Aluminum Socketless Reusable Push-On Hose Barb Ends for AN Fittings
x
            

These lightweight socketless fittings are machined from aluminum alloy and anodized red and blue with a luster finish, the ultimate in professional appearance. Precision machine work ensures a positive seal when coupling Full Flow™ hose ends to your carburetor. They are ideal for use as fuel line connectors or adapters.

  • AN to hose barb 
  • Choose straight, 45°, 90°, 120° or 180°. Then choose -6, -8, -10 or -12 AN size.
  • Use with Aeroquip Special Application blue hose
  • For use with 37° AN style fittings

Socketless Fitting Application Chart (GIF)

AN Thread Size Guide (GIF)

Fitting Thread Size Guide (GIF)

9 Super 7   Secondary 3-Bolt 2 Barrel Carburetor, Chrome Finish
9 Super 7 Secondary 3-Bolt 2 Barrel Carburetor, Chrome Finish
x
            

Speedway Motors now offers a reproduction version of one of the most popular carburetors ever used, the original Stromberg 97! Original equipment on '30s and '40s cars and trucks, the Stromberg 97 has long been favored by flathead hot rodders and racers who realized the performance qualities of this timeless fuel supplier.

For years customers have been either putting up with poor idling multiple carburetor set-ups or spending hundreds of dollars converting the secondary carburetors so they did not have to idle circuits. Now Speedway Motors is offering our popular 9 Super 7® two barrel "secondary" carburetor with all that work already done. No more wasted money!

Speedway Motors has incorporated all of the improvements shown above while maintaining the carburetor's original look. Features such as the accelerator pump, main jets and cosmetics have all been faithfully retained. Additionally, each carburetor is individually flow tested and inspected for leaks. Perfection is the result! 

Aesthetically, the 9Super7 Carb is nearly identical to the stock unit, minus the large 97 logo that appeared on the side and the patent numbers found on the float bowl area. Upgraded internal parts include; the float, needle, and seat. Jetting and power valve settings remain as they were for the original 97 carbs as well as the cfm and vacuum specs.

The other similarity that the 9 Super 7 shares with the original 97 is the setup and tuning necessary to yield a well-running machine. While perhaps not as simple as bolting on a single four-barrel, the 9 Super 7 makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required is an intake, a linkage system, a Uni-Syn syncing tool, and a little patience. Be sure to include the Primary 9 Super 7 when installing multi-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb set-up.

  • All-new tooling for crisp, flawless castings
  • New aluminum base assembly allows for cooler fuel temps and better fuel efficiency as compared to the original cast iron design
  • Stainless steel screws and hardware
  • Accelerator pump, and jets have all been faithfully retained and accept standard Stromberg parts
  • Features original Stromberg 0.97" venturi diameter
  • Modern Nitrophyl float and Neoprene gaskets
  • Original troublesome needle and seat replaced by a Grose-style fuel inlet valve to better cope with higher fuel pressures and improved high speed running 
  • Will not stick or dribble like the old Viton-tipped needle and seat setups
  • Grose-style jet valve won't corrode in modern fuel, something the original needle and seat units can't do
  • Comes with a No. 65 power valve and 0.045" main jets, identical to the stock 97
  • Extended brass throttle shaft to simplify multi-carb linkage
  • Special base plate with no idle circuits or choke linkage
  • Special butterflies and shafts installed
  • Works best with progressive linkage
  • Idle only off the center or main carburetor
  • No more plug foul

"T-Bucket, Air and Fuel Delivery" Page 1 of 25

  • Three-Bolt Carb Base Gasket
    $1.99
    Three-Bolt Carb Base Gasket
    x
                Three bolt carburetor base gaskets fit Stromberg 97-style carbs and Holley 94-style carbs.
            
  • Late Carburetor Adapter
    $24.99
    Product Rating: 4.00 Stars
    Late Carburetor Adapter
    x
                

    Bolt a newer type 4-bolt carb (3-1/4" x 1-7/8", like Rochester 2GC) to an early 3-bolt manifold. Aluminum casting.

    560-5159 Instructions (PDF)

  • Holley Carburetor Gas Needle and Seat, .110 Inch
    Holley Carburetor Gas Needle and Seat, .110 Inch
    x
                "Viton" needle and seat is resistant to dirt and provides superior seal when closed. Size .110" for gas carbs. Gasket not included. 
            
  • Fuel Filter Mounting Bracket
    Fuel Filter Mounting Bracket
    x
                

    These fuel filter mounting brackets are CNC machined aluminum. Available in 1-3/8", 1-1/2", or 1-3/4" round tubing.

    These brackets are designed to be used with our filters. Hole is 2" inner diameter. 

  • Flathead Ford Fuel Pump Stand Bolt Kit
    Flathead Ford Fuel Pump Stand Bolt Kit
    x
                Premium stainless steel socket head bolts for your Flathead Ford fuel pump stand. Each kit includes stainless steel AN washers.
            
  • Open 4 Barrel Carburetor Base Gasket
    Open 4 Barrel Carburetor Base Gasket
    x
                Open base gaskets.
            
  • JAZ Products 300-000-20 Fender Mount Fuel Filler Kit
    JAZ Products 300-000-20 Fender Mount Fuel Filler Kit
    x
                

    For remote filling of fuel cell. Kit contains a 12-bolt recessed fender fill assembly with vented cap (1/2 turn, twist & lock style). Fender filler flange measures 6-1/4" outside diameter.

    Cap and base are made of galvanized steel. Fill and vent hose are clear polyethylene. Use with fast fill valve.

  • Lokar SRK-4000 Carburetor Bracket and Return Spring
    Lokar SRK-4000 Carburetor Bracket and Return Spring
    x
                

    Stainless bracket mounts to rear of Holley, Edelbrock, AFB, Quadrajet, Demon, and In-Line Dual Quads. Stainless bracket and dual stainless springs are used to mount Lokar’s Throttle Cable and Kickdown kits. Design provides improved clearance on Edelbrock carbs. Includes tension screw to prevent bracket from movement under extreme pressure on a kickdown cable, such as with a 700-R4 transmission.

    Mounts Lokar Throttle Cables and Kickdowns for a nice clean setup. Includes allen wrench to adjust the set screw.

  • Carb and Fuel Pump Fitting, 1/2 Inch-20, AN 6
    Carb and Fuel Pump Fitting, 1/2 Inch-20, AN 6
    x
                

    #6 Ford, Chrysler and early Chevy fuel pumps with 1/2"-20 inverted flare thread.

    Fitting Thread Application Chart

  • Tri-Bar Wing Nut Style Air Cleaners
    Tri-Bar Wing Nut Style Air Cleaners
    x
                

    Just the ticket for that tri-power setup! These chrome plated steel air cleaners have a 4" x 2" replaceable paper element and will fit 2-5/8" and 2-5/16" carbs.

    Comes with a metal screw to secure it to the carb neck from the top side. Includes tri-bar style retaining nut.

  • Fuel Tank Roll-Over Vent Valve
    Fuel Tank Roll-Over Vent Valve
    x
                

    This safety device will automatically stop fuel flow if your car somehow gets upside down. Inside is a needle/ball seat which stops fuel flow out the vent if you get upside down.

    • Accepts 5/16" hose
    • Fits into 1/4" npt port
    • Measures 3" bottom-to-top
  • Ford/Holley 94 Extended Throttle Shaft
    Ford/Holley 94 Extended Throttle Shaft
    x
                

    About the only way your 94 carburetor could have a tight throttle shaft would be if you found a NOS carb somewhere. Now you can build yourself a dual or triple carb three deuce set-up that will run like new. We offer you these new extended throttle shafts that are .282" which is .005" oversize. You simply run a 9/32" drill bit or reamer through the base plate and you now have a tight carb again.

    Includes (4) throttle butterfy plate screws and a 6-32 x 1/4" truss head end screw (slotted head).

  • Aeroquip Special Application Socketless AN Hose, Black
    Aeroquip Special Application Socketless AN Hose, Black
    x
                
  • Textile braid reinforcement
  • Low pressure design for use with socketless reuseable fittings only
  • No hose clamp necessary
  • Ideal hose for fuel line applications
  • 50,000 ft of hose in stock!
  • Construction: AQP elastomer tube, textile braid reinforcement, black AQP elastomer cover.

    Application: For gasoline, fuel and lubricating oils, air and water. Not recommended for hydraulic impulse applications and is not approved for air brake, hydraulic brake or power steering applications.

    Operating Range: Max Operating pressure: 250 PSI. Minimum burst pressure: 1000 PSI. Operating Temperature Range -40°F to 300°F. Air not to exceed +250°F and water not to exceed +180°F. Reduced pressure operation allows for temperatures up to 300°F.

    Aeroquip Hose Sizing Guide (GIF)

    Hose Fitting Sizing Chart (GIF)

  • Three Plain 9 Super 7   Carbs on 1957-86 Small Block Chevy Edelbrock Intake
    Three Plain 9 Super 7 Carbs on 1957-86 Small Block Chevy Edelbrock Intake
    x
                

    This tri power kit uses the Edelbrock C-357-B S/B Chevy 3x2 intake with Speedway's 9 Super 7® carbs. It has progressive linkage to give you good driveability and economy, but power when you need it. The manifold has a balanced 180° firing order port runner arrangement. It contains an exhaust gas heat riser and offers excellent performance potential. (idle-5500 rpm)

    Kit includes three carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required. Fits 1957-1986 Chevy 262-400 c.i.d. small-block Chevys.

    9 Super 7® Linkage Instructions (PDF)

    Note: Not applicable to an HEI based distributor system due to a clearance issue. This system must be used in conjunction with a small diameter based distributor.

    The 9Super7 Carb  makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both prima

  • Quick Release Cable or Linkage End, 1/4-28 RH
    Quick Release Cable or Linkage End, 1/4-28 RH
    x
                These steel ends are perfect for throttle cable or linkage that needs to be quick release. They have the same thread on the stud as they do in the body. 
            
  • Nitrophyl Float for 97 Carb
    $14.99
    Nitrophyl Float for 97 Carb
    x
                Modern solid Nitrophyl float for your vintage Stromberg 97-style carburetor.
            
  • K&N Filters 99-0516 Air Filter Oil, Aerosol
    K&N Filters 99-0516 Air Filter Oil, Aerosol
    x
                

    K&N Air Filter Oil is the only oil specially formulated to work in combination with the cotton fabric in K&N Filtercharger elements providing a superior air filtration system. When used as directed, it quickly penetrates the filter pleats, where it remains suspended in the cotton fabric. Saturation is maintained until the element is cleaned with K&N Air Filter Cleaner.

    NOTE: Aerosol items cannot be shipped by air.

  • Pump Frame Tube Clamp for 1-1/4 Inch Tube
    Pump Frame Tube Clamp for 1-1/4 Inch Tube
    x
                

    Pump Frame Tube Clamp for 1.250" Tube for FUELAB Prodigy pump.

  • Louvered Style Air Cleaners
    $9.99
    Product Rating: 4.60 Stars
    Louvered Style Air Cleaners
    x
                

    Just the ticket for that tri-power setup! Chrome plated steel housing with 4" x 2" replaceable paper element. Fits Holley 94, Stromberg 97, Speedway 9 Super 7, Demon 98 and Rochester 2 barrels (all with 2-5/8" neck). 

    Retained with a #36 hose clamp.

  • Throttle Ball Assortment
    $9.99
    Product Rating: 5.00 Stars
    Throttle Ball Assortment
    x
                

    Many applications use a ball on the carburetor arm to hook the linkage to. This handy little assortment of 4 throttle balls with various threads will allow you to finish up linkage.

    Includes

    • 1/4" threaded stud, .222" ball, .131" ball stud
    • 1/4" threaded stud, .250" ball, .160" ball stud
    • 3/16" threaded stud, .267" ball, .157" ball stud
    • 3/16" threaded stud, .241" ball, .132" ball stud
  • Edelbrock 1405 Performer 600 CFM 4 Barrel Carburetor, Manual Choke
    Edelbrock 1405 Performer 600 CFM 4 Barrel Carburetor, Manual Choke
    x
                

    Edelbrock Performer Series four barrel carbs have proven themselves to be easy to tune with great drivability. Whether you need to replace an aging stock carb or are looking for a performance 4 barrel carb to top off your hot rod, the Edelbrock Performer Series carbs are the best choice for performance and value. All Edelbrock parts are proudly made in the U.S.A.  

    This 600 CFM 4 barrel carburetor is designed and calibrated for optimum street performance in small-block and some big-block engines. Match with a variety of manifolds that include Edelbrock Performer, Performer EPS, Performer RPM, RPM Air-Gap, Torker II and other brands of similar design. Includes manual choke and detailed instructions. Ford/Mopar throttle adapter arms sold separately. 

    Edelbrock 600 CFM 4 Barrel Carburetor Installation Instructions (PDF)

  • MSD 2225 In-Line Hi-Pressure Fuel Pump
    MSD 2225 In-Line Hi-Pressure Fuel Pump
    x
                

    Most modern engines have a hi-pressure fuel pump located in the gas tank. If you are transplanting one of these engines into your hot rod, what are you going to do for a fuel pump? This MSD pump can be mounted on the frame and can put out up to 43 gph at 40 psi or 39 gph at 80 psi.

    • Flows 43 gph (282 lb/hr) gasoline @ 40 psi and 12 volts/5.4 amps 
    • Supports most multiport EFI systems up to 500 horsepower
    • Mounts in-line (out of the fuel tank)
    • Roller vane pump mechanism is extremely resistant to clogging and jamming
    • Has 3/8” hose barb inlet and 5/16" hose barb outlet
    • Made in the USA
  • Holley 94 2 Barrel Carburetor Rebuild Kit
    Holley 94 2 Barrel Carburetor Rebuild Kit
    x
                

    Model AA-1 2100, & 2110 (Replacement 97 Carb). Complete gasket set includes new needle & seat, power valve and accelerator pump.

    910-11596 Instructions (pdf)

  • Carb Linkage Thread End for 9 Super 7   /Stromberg 97/Demon 98 Carbs, RH
    Carb Linkage Thread End for 9 Super 7 /Stromberg 97/Demon 98 Carbs, RH
    x
                

    This carb linkage rod end has 3/16" fine RH threads (also known as 10-32).  It is intended for use with 9 Super 7 ®, Stromberg 97, and Demon 98 carburators.

    • 3/16" fine RH threads (10-32)
    • Secures with pin
    • Steel
    • .430" Diameter
    • Application:
      • 9 Super 7 ®
      • Stromberg 97
      • Demon 98
  • Spun Aluminum Fuel Tank, 11 Gallon, 10 x 33 Inch, Offset Outlet
    Spun Aluminum Fuel Tank, 11 Gallon, 10 x 33 Inch, Offset Outlet
    x
                

    These spun aluminum tanks have an unpolished, spun aluminum finish, 2-1/4" neck, and a 1/4" NPT female outlet. For all off-road vehicles. The screw-on vented cap and brackets are included and can be found in a false bottom of the packaging box.

    This tank features a fuel outlet that is 3" from the end opposite the filler neck.

  • 97 Carb Scoop
    $19.99
    Product Rating: 5.00 Stars
    97 Carb Scoop
    x
                

    This "97" carb scoop is a polished aluminum casting with a copper screen and locking screw. It features timeless 1950's styling with a "frog mouth" shape and fits all Stromberg 97 style and Holley/Ford 94 style carbs with a 2-5/8" diameter neck. It is compact enough for all multi-carb setups.

    Attaches to the carb with a single set screw.

  • Air Cleaner Nut
    $9.99
    Product Rating: 3.67 Stars
    Air Cleaner Nut
    x
                

    Easy grip air cleaner nut features a bottom O-ring seal to keep dust and debris from entering your engine. Available for 1/4" or 5/16" studs.

    • Diameter at Top:  1-1/2"
    • Diameter at Base:  7/8"
    • Height:  1-1/4"
  • 3-7/8 Inch Washable Air Filters
    3-7/8 Inch Washable Air Filters
    x
                

    Our washable replacement filters outlast typical paper media filters because they can be washed and reused. Simply wash the filter using K&N Filter Cleaner and then re-oil it with K&N Air Filter Oil.

  • Aircraft Style Fuel Filler Neck & Cap
    Aircraft Style Fuel Filler Neck & Cap
    x
                

    Flush-mount caps offer excellent aerodynamic performance, large fill opening and attractive appearance. Cap features a positive seal, flip-up 1/4-turn handle, and a chain to secure it to the gas filler neck. Includes cap, chain, fuel filler neck, gasket, and all hardware. Polyethylene cap is vented.

    Hole in tank needs to be 3-3/4" for cap to sit flush.

  • 6-3/8 Inch Chrome Air Cleaner, 4 Barrel Carb, 5-1/8 Inch Neck
    6-3/8 Inch Chrome Air Cleaner, 4 Barrel Carb, 5-1/8 Inch Neck
    x
                

    Keep the air entering your engine clean with our chrome plated steel air cleaners. They feature a recessed base and have a 6-3/8 in. diameter.  These air cleaners have a chrome plated steel housing with a paper filter element.

    6-3/8 Inch Chrome Air Cleaner, 4 Barrel Carb.

    • Chrome plated steel
    • 6-3/8" diameter and 2-1/2" tall filter element
    • Fits 4 barrel carbs with 5-1/8" neck
    • 3-3/4" tall from the base to the highest point on the top.
    • includes stud and wing nut
    • non-restricting flame retardant filter
    • unique sculptured design to fit most applications
    • performance engineered for increased breathing
    • designed to perform with today's large displacement engines

     

  • Speedway Throttle and Kickdown Cable Bracket Kit
    Speedway Throttle and Kickdown Cable Bracket Kit
    x
                Chrome plated, fully adjustable throttle cable and automatic transmission kickdown cable bracket bolts to the corner of most 2bbl. or 4 bbl. carburetors. Steel bracket locks in place and won't swivel. Works with OEM cable housings that have square plastic ends which snap into the bracket holes.
            
  • Adjustable Main Jets for Stromberg-Style Carbs
    Adjustable Main Jets for Stromberg-Style Carbs
    x
                

    If you are like us you really don't like pulling the carbs off to change jets over and over... These adjustable main jets will make life a little easier and get your car running right, a lot faster. Machined to high standards on Swiss screw machine. Part has a stainless steel needle and brass body and nut with Viton O-ring seal.

    Simply remove your jet well plugs and screw in this adjustable jet assembly. Use the largest stock jet size for the richest mixture you need, then use the adjuster to lean it down from there. You can lean your mixture by turning clockwise or richen by turning counter clockwise. Includes Teflon sealing washer, extra O-ring seals & instructions.

    • Get your plug color just right
    • Compensate for altitude changes
    • Get the best tuneup your hot rod has ever had

    Fits Stromberg 48, 81, and 97-style carburetors. Sold as a PAIR.

  • Small Block Chevy Intake Bolt Kits
    Small Block Chevy Intake Bolt Kits
    x
                A bolt kit for S/B Chevy intakes. All feature that unique King Chrome premium chrome plating.
            
  • Mr. Gasket 1514 Chrome Fuel Pump Mounting Plate, Small Block Chevy
    Mr. Gasket 1514 Chrome Fuel Pump Mounting Plate, Small Block Chevy
    x
                

    Mr.Gasket announces a fuel pump mounting plate to dress up the fuel pump area of your engine. This chrome plated mounting plate, for the 265-400 cu. in. Chevrolet small block engine, is ideal for mounting a stock OEM pump. The mounting plate is precision cut to cover the stock fuel pump opening and is complete with gasket.

    • Quality chrome finish
    • Fits 265-400 SBC engines
    • Mounts stock OEM pump
    • Includes gasket
  • Chrome Plated Stainless Steel Flush Mount Fuel Fill
    Chrome Plated Stainless Steel Flush Mount Fuel Fill
    x
                

    This chrome plated stainless steel fuel fill can be flush mounted and includes a special opening key. Simple three hole mounting makes installation a snap.

    Use with 1-1/2" I.D. hose (sold separately).

  • Replacement Screen for 97 Carb Scoop
    Replacement Screen for 97 Carb Scoop
    x
                4.5" x 4.5" flat replacement screen for 97 Carb Scoop 916-11001. Can also be used to make your own custom air intake screen or air filter screen.
            
  • Speedway Carburetor Bracket and Return Springs
    Speedway Carburetor Bracket and Return Springs
    x
                Stainless throttle cable bracket & spring set. Mounts to rear of Holley, Edelbrock, AFB, Quadrajet, Demon, and in-line dual quad carburetors. Dual spring design provides a safe, reliable throttle return when compared to single spring set-ups.

    Note: There is no provision in this bracket for an automatic transmission.
  • Edelbrock 2701 Performer EPS Chevy Intake Manifold
    Edelbrock 2701 Performer EPS Chevy Intake Manifold
    x
                

    Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

    Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most.

    IMCA racing approved.

    325-2701 Instructions (PDF)

  • Speedway Universal Throttle Linkage Bell Crank Kit
    Speedway Universal Throttle Linkage Bell Crank Kit
    x
                This bell crank kit features 12 mounting holes for multi-arm positioning and can be used in either push or pull type throttle linkages. Center hole is 1/4" diameter for easy mounting. Each arm has 3 holes for various throttle ratios. Includes all hardware needed for installation. 
            
  • Double End Carburetor Linkage, 9 Inches Long
    Double End Carburetor Linkage, 9 Inches Long
    x
                

    3/16" steel rod carburetor linkage with double ends. Thread size is 10-32 RH and LH. For use with 9 Super 7®, Stromberg 97, and Demon 98 carbs.

Goto Previous PagePrevious Page
1 2 3 4 5 ... 25