Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 8

Products

Suspension Kits

Shop Suspension At Speedway Motors

Nothing beats a car with the right suspension set-up. Whether it's on the track or on the street, Speedway Motors is ready to set you up with the suspension components you need. From leaf springs and coil-overs to torsion bars and shocks, our techs can get you the set up you want on pretty much anything with wheels!


Featured Products
  • Speedway Model T, A, 1932-34 Four-Bar Rear Suspension Kit, Plain Steel
    Speedway Model T, A, 1932-34 Four-Bar Rear Suspension Kit, Plain Steel
    (Part #91649055)
    x
                

    Features heavy wall 21-1/2" rods with plain steel brackets. Exclusive sandwich-style brackets give greater bar support and incorporate a multi-position lower coil-over mount. 

    Complete kit includes: mild steel rods, steel brackets, bushed rod ends, and hardware. Lower coil-over shock mount stud not included. The nuts & bolts supplied in this kit are NOT polished or plated.

    • Rod length is 21-1/2"
    • Center-to-center of 4-bar eyelets is 5.5"
    • Bracket width is 1.39"

    This kit comes in two varieties:

    • TA - to fit narrow frames such as Model T or Model A
    • 3234 - to fit wider frames such as 1932-1934 Ford

    Note:  Four bar rear suspension kits require the use of a side to side control such as a panhard bar or a watts link component.

    916-49055 Instructions (PDF)

  • Deluxe Coil-Over Rear Suspension Kit, Plain Finish
    Deluxe Coil-Over Rear Suspension Kit, Plain Finish
    (Part #91649060)
    x
                

    This rear suspension kit is loaded with high quality components from Speedway and Carrera. Kit includes a steel panhard bar, chrome plated Carrera coil-over shock assemblies, bare steel 32" radius rods, and all mounting brackets and hardware. The Carrera 3-way adjustable, gas pressurized and radial tuned shocks provide an excellent ride. Welding is required for assembly.

    • Kit includes:
      • Steel panhard bar
      • Chrome plated Carrera coil-over shock assemblies
      • Bare steel 32" radius rods
      • All mounting brackets and hardware

    Comes with your choice of spring rate. Use the Spring Rate Guide and Coil-Over Mounting guide to select to proper rate for your vehicle.

    Spring Rate Guide (GIF) 

    Coil-Over Mounting Guide (GIF) 

    916-49060 Instructions (PDF)

  • AccuAir AA-AMP2-TPAD-EN-5C E-Level Stage 2 Air Suspension Management Kit
    New
    AccuAir AA-AMP2-TPAD-EN-5C E-Level Stage 2 Air Suspension Management Kit
    (Part #9109900)
    x
                

    This AccuAir E-Level Air Management Kit with Touchpad includes everything you need to control the air suspension on your ride. This kit includes top of the line e-level controller with touchpad, two 400c compressors with a 5 gallon tank, and it features 3 programmable ride heights. This kit also features 3/8" D.O.T approved plumbing kit and 4 corner valve unit. This is a great all in one package!

    • E-level controller with touchpad
    • 400c compressors (2)
    • 5 gallon tank
    • 3 programmable ride heights
    • 3/8" D.o.t approved plumbing kit
    • VU4 4-Corner Solenoid Valve Unit provides responsive and reliable air spring control in a single compact, pre-wired, leak-free package
    • Includes e-Level 4-Corner Electronic Leveling System Features:
      • 3 Programmable Heights Lowered / Ride Height / Raised
      • RideMonitor Mode adjusts as needed while driving or parked
      • TruPosition Height Sensors provide accurate leveling regardless of load
      • Ride-Height-on-Start gets you ready to drive when you turn the key
      • Anti "Cross-loading" Height Management gives balanced spring weights
    • Automatically Calibrates to any Air Suspension System on any vehicle, (NO user programming required)
    • Straight to Height adjustments avoid valve "pulsing" and gets you ready to drive immediately
    • Active Learning maximizes leveling performance after every adjustment
    • Manages Air Compressors for faster recovery
    • Monitors Vehicle Voltage and automatically turns compressor(s) OFF at 10.5 volts to prevent a dead battery
    • 100% Weather-Proof for under vehicle mounting
    • Plug-n-Play wiring harnesses for ease of installation
    • Each System is 100% Factory Tested

    Each Stage 2 Kit Includes:

    • (1) e-Level Electronic Leveling System w/ TouchPad Interface
    • (1) VU4 4-Corner Solenoid Valve Unit
    • (2) Viair 400C Compressors
    • (1) 5-Gallon Anodized Aluminum Air Tank
    • (1) Anodized Aluminum Serviceable Air Filter w/ 3/8" Straight Fittings
    • (50') 3/8" D.O.T. Approved Air Line
    • (4) 3/8" - 1/4" NPT D.O.T. Approved Swivel Elbows for Air Springs
    • (1) 3/8" - 1/4" NPT D.O.T. Approved Straight Fitting for Tank
    • (1) 6 ml tube of Loctite 565 Thread Sealant
    • (1) Stainless Steel Mounting Hardware Package
    • (1) Illustrated Installation & Operation Manuals

    Installation Manual (PDF) 

    Operation Manual (PDF) 

    Additional Information (PDF) 

  • Spring-Behind 4 Inch Drop Tube Axle Front End for Ford Spindles, Plain
    Spring-Behind 4 Inch Drop Tube Axle Front End for Ford Spindles, Plain
    (Part #91339006)
    x
                

    For 1937-1948 early Ford passenger car spindles. Maximum car weight 2500 lbs.  Plain steel construction.

    Kit includes:

    • Two 1-3/4" spring shackles w/ nylon bushings
    • Two spring pivots
    • 26" 4-leaf spring w/ nylon buttons
    • Two axle brackets
    • Tube axle, 48" eye-to-eye, 4" dropped
    • Two 27" radius rods
    • Four clevises with jam nuts and bolts
    • Two 5/8" Heims with jam nuts
    • Spring U-bolts sold separately

    Instructions (PDF)

    Front Axle/Suspension Tech Tips (GIF) 

  • Mustang II IFS, Standard Tubular Control Arms, Stock Springs and Spindles
    Mustang II IFS, Standard Tubular Control Arms, Stock Springs and Spindles
    (Part #91034202)
    x
                

    Includes standard upper and offset strutless lower control arms, new standard spindles, rubber brake lines, new black stock type springs and shocks, new manual or rebuilt power rack & pinion with bushings and new tie rods. The 11" brake kit features GM Metric calipers, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.

    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • New Stock Spindles, Springs, and Shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers for 27-1/2" - 33-1/2" frame widths, you will be required to purchase 2" Inner Tie Rod Extensions (91034345) or (91034346).

     

  • Model A to 1934 Ford 48 In I-Beam Axle Radius Rod Kit - Ford Spindle
    Model A to 1934 Ford 48 In I-Beam Axle Radius Rod Kit - Ford Spindle
    (Part #91639506)
    x
                

    Speedway Radius Rod I-Beam axle kits are designed to fit '28-'31 Model A and '32-'34 Ford frames. I-Beam axles require '37-'48 Ford passenger car spindles. Kits are available in Plain steel or Chrome.

    Each kit includes:

    • 48" kingpin-to-kingpin I-beam axle, 4" dropped
    • 27" hairpin radius rods
    • Forged steel perch bolts
    • Forged steel lower shock mounts (key-slotted design)
    • Spring shackles w/ nylon bushings
    • 31-1/4" eye-to-eye 4-leaf Super Glide spring, 1-3/4" wide
    • All hardware for assembly

    916-39506 Instructions (PDF)

    Front Axle/Suspension Tech Tips (GIF)

  • AccuAir AA-RF-FOB E-Level Air Suspension Wireless Key-Fob and Receiver Kit
    New
    AccuAir AA-RF-FOB E-Level Air Suspension Wireless Key-Fob and Receiver Kit
    (Part #9109907)
    x
                

    These AccuAir air suspension wireless Key-Fob Module and Reciever Kits give you e-Level System wireless capability. The 4-button Key-Fob allows you to trigger any of your three saved heights with any AccuAir suspension system. The key-fob will work from up to 200 feet away and only operates when the vehicle ignition is OFF for safety.

    • Wireless Key-Fob Module and Reciever
    • For e-Level Systems
    • Trigger any of your three saved heights from the palm of your hand
    • Key-fob works from up to 200 feet away
    • Operates only when vehicle ignition is OFF
  • Spring-Behind 4 In Drop Tube Axle Front End for Chevy Spindles, Plain
    Spring-Behind 4 In Drop Tube Axle Front End for Chevy Spindles, Plain
    (Part #91339010)
    x
                For 1949-1954 early Chevy passenger car spindles. Maximum car weight 2500 lbs. 

    Kit includes:

    • Two 1-3/4" spring shackles w/ nylon bushings
    • Two spring pivots
    • 26" 4-leaf spring w/ nylon buttons
    • Two axle brackets
    • Tube axle, 48" eye-to-eye, 4" dropped
    • Two 27" radius rods
    • Four clevises with jam nuts and bolts
    • Two 5/8" Heims with jam nuts
    • Spring U-bolts sold separately

    Front Axle/Suspension Tech Tips (GIF)


Filter

"Suspension Arms, Bushings and Accessories, Suspension Kits" Page 1 of 8

Page 1 of 8

  • 1928-31 Ford Model A Front Four-Bar Kit, Stainless Steel
    1928-31 Ford Model A Front Four-Bar Kit, Stainless Steel
    (Part #91639001)
    x
                

    Four bar suspensions allow your front axle to travel freely, thus providing better ride and handling than traditional radius rods. Plus, their polished stainless construction will keep your front end glowing forever! Speedway kits feature bat wings and tapped bar ends, complete with nylon rod ends. For axles with 2" or 2-1/4" boss - use spacers 916-35003 if necessary.

    For 1928-1931 Ford Model A. 

    916-39001 Instructions (PDF)

  • Mustang II IFS, Narrow Control Arms, Coilover Springs, Stock Spindles
    Mustang II IFS, Narrow Control Arms, Coilover Springs, Stock Spindles
    (Part #91034208)
    x
                Please view the product's page for more information
            
  • Spring-Behind 6 In Drop Tube Axle Front End for Ford Spindles
    Spring-Behind 6 In Drop Tube Axle Front End for Ford Spindles
    (Part #91339118)
    x
                For 1937-1948 early Ford passenger car spindles. Maximun car weight 2500 lbs.

    Kit includes:

    • Two 1-3/4" spring shackles w/ nylon bushings
    • Two spring pivots
    • 26" 4-leaf spring w/ nylon buttons
    • Two axle brackets
    • Tube axle, 48" eye-to-eye, 6" dropped
    • Two 27" radius rods
    • Four clevises with jam nuts and bolts
    • Two 5/8" Heims with jam nuts
    • Spring U-bolts sold separately

    Instructions (PDF)

    Front Axle/Suspension Tech Tips (GIF)

     

  • 1935-40 Ford Four Bar Rear Suspension Kit
    1935-40 Ford Four Bar Rear Suspension Kit
    (Part #91649059)
    x
                

    This parallel 4-bar kit is designed for our 1935-1940 Ford frame (916-57049), but it will also work with a boxed original OEM frame. Rear brackets have 3 mounting holes for adjustable ride height. Adjustable bars have a 1" O.D. with urethane bushings and all necessary hardware. Plain finish, welding required. 

    • '35-'40 Ford car
    • '35-'41 Ford pickup (1/2 ton) 
  • Forged I-Beam Split Wishbone Front End Kit
    $649.99
    $699.99
    Product Rating: 3.50 Stars
    Forged I-Beam Split Wishbone Front End Kit
    (Part #91639516)
    x
                

    Split bones front end kit for '37-'48 Ford style spindles. Kit is based on our 910-35140.

    Kit Includes:

    • Wishbone style radius rods
    • Radius rod frame mounts
    • 29” leaf spring
    • Shackles
    • Perches
    • Lower shock mounts
    • Hardware
  • Ford Upper Steering Arm, Chrome, 7-3/4 Inch, 5/8 Hole
    Ford Upper Steering Arm, Chrome, 7-3/4 Inch, 5/8 Hole
    (Part #91632012)
    x
                Flame cut steel upper steering arm for '37-'48 Ford spindles (with 3-3/8" mount centers). This design is available in 6-1/4" or 7-3/4" lengths. The longer 7-3/4" arms permit a tighter left turn when using large diameter front tires or front wheels with a deep reverse, and it also slows the steering rate for greater control. Tapped 5/8" end accepts spherical rod ends. 

    NOTE: Upper steering arms allow the attachment of a drag link to the LH (driver's side) spindle. The arms attach with bolts through the upper 2 backing-plate-mounting holes on spindle.

    Steering Arm Ends Guide (GIF)

    Parallel Steering Set-Up Guide (GIF)

  • 1932 Ford Lo-Boy Rear End Mounting Kit
    1932 Ford Lo-Boy Rear End Mounting Kit
    (Part #97449932)
    x
                

    This kit links your rear axle to the '32 Lo-Boy frame mounts using quarter elliptic springs, upper radius rods & a Panhard bar. Quarter elliptic springs not included in kit (sold separately). Builder can cut their own springs from a pair of factory leaves as well. For maximum performance, use Composite Quarter Elliptic Mono-Leaf Springs 974-49934.

    See Notes tab for complete kit list. 

  • Mustang II Coilover IFS w/ Stock Control Arms, Coilovers, Dropped Spindles
    Mustang II Coilover IFS w/ Stock Control Arms, Coilovers, Dropped Spindles
    (Part #91034201)
    x
                With our complete Mustang II Independent Front Suspension kit you get   brand new stamped steel upper and lower control arms with polyurethane   bushings, steel 2" dropped spindles, Rubber Brake Lines, Carrera coil-over shock & spring, new manual rack & pinion with bushings   or remanufactured power rack & pinion with bushings and an 11"  brake  kit featuring GM Metric-style calipers, with your choice of 5 x  4-1/2"  or 5 x 4-3/4" bolt patterns. 
    • Works with most Speedway and Heidts crossmembers (be sure to check control arm correspondence when choosing crossmember for your vehicle)
    • These kits are compatible with your application based on which crossmember you have.
    • Kit Includes:
      • New stamped steel upper and lower control arms with polyurethane bushings
      • 2" dropped spindles
      • Carrera coil-over shock & spring
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Crossmember NOT included - Add proper crossmember to complete kit.

    Spring Rate Chart (

  • Speedway Spring-Over 6 Inch Drop Front End for Ford Spindles, Chrome
    Speedway Spring-Over 6 Inch Drop Front End for Ford Spindles, Chrome
    (Part #91339017)
    x
                

    For T's and early 1930's street rods using 1937-48 Ford passenger car spindles. Maximum car weight is 2500 lbs.

    Kit includes:

    • Two 1-3/4" spring shackles with nylon bushings
    • Two spring pivots
    • 26" 4 leaf Super Glide™ spring, 1-3/4" wide
    • Two axle brackets
    • Tube axle, 48" eye-to-eye, 6" drop
    • Two 27" radius rods
    • Four clevises with jam nuts and bolts
    • Two 5/8" heims with jam nuts
    • Spring U-bolts sold separately
  • Front End Assembly for Model A Frame, Tube Axle Kit, Chrome
    Front End Assembly for Model A Frame, Tube Axle Kit, Chrome
    (Part #91639515)
    x
                

    These front suspension packages make it easier to begin transforming your Model A frame into a rolling chassis. Kits include a 3" drop tube axle, 27" radius rods, leaf spring and shackles. Kit works well with the SM300 Pro Shocks (shocks not included).

    Axle kit designed to work with frame #916-57045.

    Front Axle/Suspension Tech Tips (GIF) 

  • 1971-72 Chevy Pickup Front End Rebuild Kit
    1971-72 Chevy Pickup Front End Rebuild Kit
    (Part #91007172)
    x
                Want to make your truck handle like new? Installing one of our complete front end rebuild kits will help. These kits include upper and lower ball joints, inner and outer tie rod ends, tie rod adjusting sleeves, an idler arm and a poly sway bar bushing kit. Kit contents may vary.
            
  • Mustang II IFS, Narrow Tubular Control Arms, Stock Springs and Spindles
    Mustang II IFS, Narrow Tubular Control Arms, Stock Springs and Spindles
    (Part #91034204)
    x
                

    Includes 5/8" narrower upper and offset strutless lower control arms, new standard spindles, rubber brake lines, new black stock type springs and shocks, new manual or rebuilt power rack & pinion with bushings and new tie rods. The 11" brake kit features GM Metric calipers, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.

    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • 5/8" narrower Tubular Upper and Lower Strutless Control Arms
      • New Stock Spindles, Springs, and Shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers fo

  • Mustang II IFS, Standard Tubular Control Arms, Stock Springs and Spindles
    Mustang II IFS, Standard Tubular Control Arms, Stock Springs and Spindles
    (Part #91034202)
    x
                

    Includes standard upper and offset strutless lower control arms, new standard spindles, rubber brake lines, new black stock type springs and shocks, new manual or rebuilt power rack & pinion with bushings and new tie rods. The 11" brake kit features GM Metric calipers, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.

    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • New Stock Spindles, Springs, and Shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers for 27-1/2" - 33-1/2&qu

  • Spring-Over 4 Inch Drop Front End for Chevy Spindles, Chrome
    Spring-Over 4 Inch Drop Front End for Chevy Spindles, Chrome
    (Part #91339003)
    x
                For T's and early 1930's street rods using 1949-54 Chevy passenger car spindles. Maximum car weight 2500 lbs. Choose Plain, Chrome, or Stainless steel.

    Kit includes:

    • Two 1-3/4" spring shackles with nylon bushings
    • Two spring pivots
    • 26" 4-leaf Super Glide™ spring, 1-3/4" wide (chrome spring used on stainless steel kit)
    • Two axle brackets
    • Tube axle, 48" eye-to-eye, 4" drop
    • Two 27" radius rods
    • Four clevises with jam nuts and bolts
    • Two 5/8" heims with jam nuts
    • Spring U-bolts sold separately

    Front Axle/Suspension Tech Tips (GIF)

  • 1932-34 Ford Front Four-Bar Kit, Plain Steel
    1932-34 Ford Front Four-Bar Kit, Plain Steel
    (Part #91639106)
    x
                Update your rod with a modern 4-bar front suspension featuring high quality components. Designed for stock style or tube axles with 2-1⁄4" bosses. Also fits 2" axles using our spacer washers 91635003. 

    Complete kit with two bat wings, four 1020 black steel bars with tapped ends, tough nylon bushings and hardware.

    916-39106 Instructions (PDF) 

  • Front End Assembly for Model A Frame, I-Beam Axle, Chrome
    Front End Assembly for Model A Frame, I-Beam Axle, Chrome
    (Part #91639517)
    x
                

    These front suspension packages make it easier to begin transforming your Model A frame into a rolling chassis. Kits include a 48" I-beam axle, radius rods, leaf spring and shackles. Kit works well with the SM300 Pro Shocks (shocks not included).

    Axle kit designed to work with frame #916-57045.

    All I-beam axles use the Ford spindle. We have brake kits with both Chevy and Ford bolt patterns available for the Ford spindle.

    The brake kit you select will determine the final track width (hub to hub). The brake kits intended for this application (the Wilwood or our 702-4475 Metric brake kit) produce a final track width of about 56-1/4". Some of the other brake kits (like the 916-31903), which are not recommended for this application, would increase the track width by over an inch.

    Front Axle/Suspension Tech Tips (GIF) 

  • Garage Sale - Aluminum Frame Mounts
    $18.99
    $48.99
    Garage Sale
    Garage Sale - Aluminum Frame Mounts
    (Part #91099600GS)
    x
                

      Mounts panhard bar to upright tube on frame

     

     These frame mounts are garage sale priced because they are slightly different than what we currently offer.

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS

  • 1932-34 Ford 4-Bar Tube Axle Kit for Chevy Spindles, Chrome
    1932-34 Ford 4-Bar Tube Axle Kit for Chevy Spindles, Chrome
    (Part #91639514)
    x
                

    Save yourself searching and confusion with these complete front suspension kits. Each kit includes a 48" wide, 3" drop tube axle, our famous urethane-bushed 21" long four bar assembly, perch bolts, lower shock mounts, spring shackles, Super Glide spring and the necessary brackets and hardware needed for assembly. (Spring and frame brackets are not stainless steel). 

    Kit requires 1949-54 Chevy passenger car spindles.

    Each kit includes:

    • 48" wide (kingpin-to-kingpin) steel tube axle, 3" drop
    • Urethane-bushed 21" long 4-bar assembly
    • Forged steel spring perch bolts
    • Forged steel lower shock mounts (key-slotted design)
    • Spring shackles w/ nylon bushings
    • 31-1/4" eye-to-eye 4-leaf Super Glide spring, 1-3/4" wide
    • All hardware for assembly

    Front Axle/Suspension Tech Tips (GIF)

  • Mustang II IFS, Narrow Control Arms, Coilover Springs, Dropped Spindles
    Mustang II IFS, Narrow Control Arms, Coilover Springs, Dropped Spindles
    (Part #91034209)
    x
                Hub-to-hub kit includes 5/8" narrower upper and offset strutless lower control arms, 2" dropped spindles, rubber brake lines, Carrera  coilovers, new manual or rebuilt power rack & pinion with  bushings and  new tie rods. The 11" brake kit features GM Metric  calipers, with your  choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • 5/8" narrower Tubular Upper and Lower Strutless Control Arms
      • 2" Dropped Spindles
      • Carrera Coilovers
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers

  • Model A 4-Bar Tube Axle Kit for Chevy Spindles, Chrome
    Model A 4-Bar Tube Axle Kit for Chevy Spindles, Chrome
    (Part #91639512)
    x
                

    Save yourself searching and confusion with these complete 1928-31 Ford Model A front suspension kits. Each kit includes a 48" wide, 3" drop tube axle, our famous urethane-bushed 21" long four bar assembly, perch bolts, lower shock mounts, spring shackles, Super Glide spring and the necessary brackets and hardware needed for assembly. (Spring and frame brackets are not stainless steel). 

    Kit requires 1949-54 Chevy passenger car spindles.

    Each kit includes:

    • 48" wide (kingpin-to-kingpin) steel tube axle, 3" drop
    • Urethane-bushed 21" long 4-bar assembly
    • Forged steel spring perch bolts
    • Forged steel lower shock mounts (key-slotted design)
    • Spring shackles w/ nylon bushings
    • 31-1/4" eye-to-eye 4-leaf Super Glide spring, 1-3/4" wide
    • All hardware for assembly

    Front Axle/Suspension Tech Tips (GIF)

     

Goto Previous PagePrevious Page
1 2 3 4 5 ... 8