Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Street Rod Steering At Speedway Motors

Let Speedway Motors "Steer" you in the right direction with the right steering components for your street rod!  From steering U-joints from Sweet Mfg. to the top steering columns and drop mounts from Ididit, we've got the best parts at the best prices around.  Don't forget to add a Speedway Motors aluminum steering wheel for the feel behind the wheel that can't be duplicated.

"Street Rod, Rack and Pinion" Page 1 of 1

  • Sweet Mfg. 001-21040 Rack and Pinion Replacement Boot
    Sweet Mfg. 001-21040 Rack and Pinion Replacement Boot
    x
                

    These high quality rubber replacement boots for Sweet Mfg. rack and pinions perform as good as they look.

    • Replacement for Sweet Mfg. rack and pinion
    • High quality rubber construction

     

  • T-Bird Offset Rack & Pinion Mount Bushings
    T-Bird Offset Rack & Pinion Mount Bushings
    x
                

    Allows the installation of a T-Bird rack & pinion with 15-1/2" center to center mounts to a crossmember built for a Mustang II with a 16" center to center mounting.

    NOTE: These bushings are not designed to raise or lower the rack & pinion.

  • Mustang II Rack Spacer, 3/4 Inch
    Mustang II Rack Spacer, 3/4 Inch
    x
                This 3/4" thick spacer works with Mustang II and '82-'88 T-Bird rack & pinions.
            
  • Mustang II Power and Manual Rack & Pinions
    Mustang II Power and Manual Rack & Pinions
    x
                

    Product update: The rebuilt power rack # 910-34340-POW as described here and in our previous catalogs has been phased out and replaced with a new rack # 910-35341

    Fits aftermarket Mustang II crossmembers. Available in manual or power steering. Mount bushings are included with the Power version, but mount bushings are NOT included in the Manual version.

    MANUAL: New manual rack and pinion steering assembly for Pinto/Bobcat/Mustang II based front suspensions in street rods and kit cars. 9/16"-26 spline input shaft. 16" mount centers. 

    POWER: Rebuilt power rack from 1982-88 T-bird. Also fits aftermarket Mustang II crossmembers. Bushings included. (Can be used with a Saginaw GM power steering pump without any additional valves or inline pressure regulators). Overall width is 45-1/8" with 15-1/2" mount centers. Must use offset bushings (910-34342) to mount to original Mustang II crossmembers. 3/4"-36 spline input shaft.

    91034340 CPP Instructions (PDF)  

  • Rack & Pinion Mounting Bushing
    Rack & Pinion Mounting Bushing
    x
                This rack & pinion mount bushing fits both power and manual Mustang II/Pinto racks.
            
  • 9 Inch Ford Gear Bearing Retaining Clip
    9 Inch Ford Gear Bearing Retaining Clip
    x
                Retains the small pinion gear snout bearing. 
            
  • 1928-32 Ford Cross-Steer Rack and Pinion
    1928-32 Ford Cross-Steer Rack and Pinion
    x
                Please view the product's page for more information
            
  • Mustang II and T-Bird Rack and Pinion Inner Tie Rod Extensions
    Mustang II and T-Bird Rack and Pinion Inner Tie Rod Extensions
    x
                

    Inner tie rod extensions for Mustang II/Thunderbird-style steering racks. Includes boots and bands.  These inner tie rod extensions fit between the inner shaft of the rack and the pivot where the tie rod attaches. It moves the pivot out to align with the pivot on the lower control arm or the imaginary line between the upper pivot and the lower control arm pivot. In doing so it leaves the tie rod in plane with the lower control arm and preserves correct steering geometry.

    The manual version does NOT have the holes for roll pins and Loctite is recommended. The power version is similar to the OEM and has 3 holes and include drift or roll pins for retention.

    Manual version (MAN) fits

    • Flaming River manual racks
    • Maval manual racks

    Power version (POW) fits

    • Mustang II power racks
    • 1982-88 Thunderbird power racks
  • Chrome Mustang II Manual Rack & Pinion
    Chrome Mustang II Manual Rack & Pinion
    x
                

    New manual rack and pinion steering assembly for Pinto/Bobcat/Mustang II based front suspensions in street rods and kit cars. Has a 9/16" 26-spline input shaft. 16" mount centers.

    Fits aftermarket Mustang II crossmembers.

  • Inner Tie Rod Extention Kit - Speedway Mustang II Manual Rack
    Inner Tie Rod Extention Kit - Speedway Mustang II Manual Rack
    x
                

    Inner tie rod extensions for Speedway manual racks. Includes boots and bands.

    910-34346 Instructions (pdf)

  • Mustang II Manual Rack and Pinion - SAE Internal Threads
    Mustang II Manual Rack and Pinion - SAE Internal Threads
    x
                NEW Mustang II Universal Manual Rack & Pinion.  Featuring quality aluminum casting with chrome plated steel center tube.  SAE threads will NOT accept rack extensions.

    • 16" mount center to center
    • All NEW components not remanufactured
    • Includes jam nuts
    • 9/16"-18 Tie Rod End threads
    • 9/16" - 26 Spline input
  • 1928-34 Ford Cross-Steer Rack and Pinion, Right Hand Drive
    1928-34 Ford Cross-Steer Rack and Pinion, Right Hand Drive
    x
                This is a great new concept for street rods with tubular or I-beam axles. It's hard to visualize how this works, but it's the hottest new idea out there! 

    Designed to replace the common Vega steering box, this rack and pinion assembly has a long passenger-side tie rod that hooks up to the spindle like a Vega-style drag link. The rack unit is mounted on a sturdy bracket that bolts to your existing Vega box mount. The rack mounts much lower and farther forward than a box to provide more clearance, and those who have installed the system report quicker steering response and easier effort than a steering box.

    The racks have 9/16" 26-spline shafts and the extension shafts are 5/8" 36-spline, just like a Vega box. Plus, our steering shaft extension 910-32244 allows you to reuse your existing steering U-joints and shafts when replacing your Vega box.

    Specify 11/16" or 5/8" tie rod thread. The 5/8" is used with a LH heim joint, 11/16" is used with a LH tie rod end. Outer tie rod and jam nut not included.

    If you are using heim ends, you may wish to order heim 175-0316 and jam nut 910-01056. If using tie rod ends, you may wish to order tie rod end 910-02919 and jam nut 910-01159.

  • Sweet Mfg Steering U-Joint, 17mm DD to 3/4 Round, Corvette, Citation Rack
    Sweet Mfg Steering U-Joint, 17mm DD to 3/4 Round, Corvette, Citation Rack
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints have a 3/4" round weld-on end.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 17MM DD

    Steering U-Joints and Couplers Application Chart (GIF)

    Steering Box/Rack/Spline Chart (Link)

    Spline Size (Link)

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • 1933-34 Ford Cross-Steer Rack and Pinion
    1933-34 Ford Cross-Steer Rack and Pinion
    x
                This is a great new concept for street rods with tubular or I-beam axles. It's hard to visualize how this works, but it's the hottest new idea out there! 

    Designed to replace the common Vega steering box, this rack and pinion assembly has a long passenger-side tie rod that hooks up to the right spindle like a Vega-style drag link. The rack unit is mounted on a sturdy bracket that bolts to your existing Vega box mount. The rack mounts much lower and farther forward than a box to provide more clearance, and those who have installed the system report quicker steering response and easier effort than a steering box.

    The racks have 9/16" 26-spline shafts and the extension shafts are 5/8" 36-spline, just like a Vega box. Plus, our steering shaft extension 910-32244 allows you to reuse your existing steering U-joints and shafts when replacing your Vega box.

    Specify 11/16" or 5/8" tie rod thread. The 5/8" is used with a LH heim joint, 11/16" is used with a LH tie rod end. Outer tie rod and jam nut not included.

    If you are using heim ends, you may wish to order heim 175-0316 and jam nut 910-01056. If using tie rod ends, you may wish to order tie rod end 910-02919 and jam nut 910-01159.

    910-32243 Instructions (PDF)

  • New T-Bird Power Rack for Mustang II Crossmembers
    New
    New T-Bird Power Rack for Mustang II Crossmembers
    x
                

    Power Steering rack fits aftermarket Mustang II crossmembers.  

    Fits aftermarket Mustang II crossmembers. Available in power steering. Mount bushings are included.

    POWER: Power rack modeled after the 1982-88 T-bird design with fitting port threads provided with a 9/16"-18 and 5/8"-18 O-ring threads. Also fits aftermarket Mustang II crossmembers. Bushings included. Uses a 3/4"-36 spline U-joint. (Can be used with a Saginaw GM power steering pump without any additional valves or inline pressure regulators).  Overall width is 45-1/8". 15-1/2" mount centers. Power rack does include the rack mounting bushings and male AN# 6 adapter fittings.

  • Unisteer 8000650-01 1928-32 Ford Right Hand Drive Cross-Steer Rack and Pinion
    Unisteer 8000650-01 1928-32 Ford Right Hand Drive Cross-Steer Rack and Pinion
    x
                

    This product from Unisteer is specifically designed for a 1928-1932 Ford street rods. This design steers off one side, creating very little bump steer that would otherwise occur. The cross steering rack and pinion offers a reduction in steering effort, even at low speeds. The cross steering increases engine and ground clearance, and supports vehicles weighing over 3000 lbs.

    • Length: 33"
    • Turns Lock to Lock: 3.75
    • Travel: 6"
    • Thread: 11/16"-18

    Includes:

    • Coupler
    • Hardware

    Note:  Cross Steer racks come with a lifetime warranty and satisfaction guaranteed!

    1928-32 Ford Cross Steer Rack and Pinion Instructions (PDF)

  • Cross Steer Rack & Pinion for 1935-40 Ford
    Cross Steer Rack & Pinion for 1935-40 Ford
    x
                

    This is a brand new 1935 to 1940 Ford Cross Steer rack and pinion. This Cross Steer rack finally allows you to put rack and pinion steering onto your early Ford straight axle!  Smooth, consistent, and easy steering throughout the entire travel. 

    This rack is designed for an unboxed frame. So, if you do not already have an unboxed frame, you must be willing to unbox a small section.
    Also, this rack only works on stock or 2" dropped axles. It will sit too low in the 4" and 6" dropped axles. Finally, if you have a wishbone
    suspension, it must be split. A four bar setup will work fine. Additional rack specs: Length: 33" Turns Lock to Lock: 3.6 Travel: 6"
     

    • Nice, easy, and consistent steering through the entire steering travel
    • Fully polished finish
    • Installs in under an hour
  • Garage Sale - New T-Bird Power Rack
    $159.99
    $199.99
    Garage Sale
    Garage Sale - New T-Bird Power Rack
    x
                

    This rack is garage sale priced because it is a little damaged from shipping.   

     NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS  

    Power Steering rack fits aftermarket Mustang II crossmembers.  

    Fits aftermarket Mustang II crossmembers. Available in power steering. Mount bushings are included.

    POWER: Power rack modeled after the 1982-88 T-bird design with fitting port threads provided with a 9/16"-18 and 5/8"-18 O-ring threads. Also fits aftermarket Mustang II crossmembers. Bushings included. Uses a 3/4"-36 spline U-joint. (Can be used with a Saginaw GM power steering pump without any additional valves or inline pressure regulators).  Overall width is 45-1/8". 15-1/2" mount ce

  • Garage Sale - New T-Bird Power Rack for Mustang II Crossmembers
    Garage Sale
    Garage Sale - New T-Bird Power Rack for Mustang II Crossmembers
    x
                Please view the product's page for more information
            
  • Garage Sale - Mopar Rack & Pinion Install Kit
    Garage Sale
    Garage Sale - Mopar Rack & Pinion Install Kit
    x
                

    Mopar Rack & Pinion Install Kit.

     

    This kit is garage sale priced because the package has been opened.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS 

  • Garage Sale - New T-Bird Power Rack for Mustang II Crossmembers
    Garage Sale
    Garage Sale - New T-Bird Power Rack for Mustang II Crossmembers
    x
                

    This crossmember is garage sale priced because it has a bent line from shipping. 

     NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS   

    Power Steering rack fits aftermarket Mustang II crossmembers.  

    Fits aftermarket Mustang II crossmembers. Available in power steering. Mount bushings are included.

    POWER: Power rack modeled after the 1982-88 T-bird design with fitting port threads provided with a 9/16"-18 and 5/8"-18 O-ring threads. Also fits aftermarket Mustang II crossmembers. Bushings included. Uses a 3/4"-36 spline U-joint. (Can be used with a Saginaw

  • Garage Sale - New T-Bird Power Rack for Mustang II Crossmembers
    Garage Sale
    Garage Sale - New T-Bird Power Rack for Mustang II Crossmembers
    x
                

    This rack is garage sale priced because one of the lines was crushed in shipping. 

      NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS 

    Power Steering rack fits aftermarket Mustang II crossmembers.  

    Fits aftermarket Mustang II crossmembers. Available in power steering. Mount bushings are included.

    POWER: Power rack modeled after the 1982-88 T-bird design with fitting port threads provided with a 9/16"-18 and 5/8"-18 O-ring threads. Also fits aftermarket Mustang II crossmembers. Bushings included. Uses a 3/4"-36 spline U-joint. (Can be used with a Saginaw GM power steering pump without any additional valves or inline pressure regulators).  Overall width is 45-1/8". 15-1/2" mount centers. Power rack does incl

  • Garage Sale - Mustang II Power Rack And Pinion
    Garage Sale
    Garage Sale - Mustang II Power Rack And Pinion
    x
                

    This rack is garage sale priced because the lines were crushed in shipping. 

     NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS 

    POWER: Rebuilt power rack from 1982-88 T-bird. Also fits aftermarket Mustang II crossmembers. Bushings included. (Can be used with a Saginaw GM power steering pump without any additional valves or inline pressure regulators). Overall width is 45-1/8" with 15-1/2" mount centers. Must use offset bushings (910-34342) to mount to original Mustang II crossmembers. 3/4"-36 spline input shaft.

    91034340 CPP Instructions (PDF)  

  • Garage Sale - Unisteer 8000650-01 1928-32 Ford Right Hand Drive Cross-Steer Rack and Pinion
    Garage Sale
    Garage Sale - Unisteer 8000650-01 1928-32 Ford Right Hand Drive Cross-Steer Rack and Pinion
    x
                Please view the product's page for more information
            
  • Garage Sale - 1999-2004 Mustang GT Rack And Pinion
    Garage Sale
    Garage Sale - 1999-2004 Mustang GT Rack And Pinion
    x
                

    This rack and pinion unit is engineered to be better than your vehicle's original equipment. Original design flaws are corrected and only the latest technology and top quality materials are used to in their construction. The result is a replacement steering rack that will fit like the original and perform even better.

    • Every rack is checked and straightened, virtually eliminating abnormal piston and seal wear
    • New high-carbon steel sleeves added to each rack and triple-bonded to the housing
    • Computer-tested for proper flow, pressure, and performance
    Additional Features & Benefits:
    • 100% new o-rings and lip seals. - Ensures no leaking and quality performance.
    • All new Teflon rings are added to the spool valve on the rack donut. - Restores internal sealing of the rack & pinion.
    • Racks are micro-finished to OE specifications. - The proper surface texture will prevent leaking between chambers and extend unit life.

    This rack is garage sale priced because it is different than what we currently offer.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS

     

  • Garage Sale - Mustang II Power Rack And Pinion
    Garage Sale
    Garage Sale - Mustang II Power Rack And Pinion
    x
                

    This rack is garage sale priced because the lines were bent in shipping. 

      NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS   

    Fits aftermarket Mustang II crossmembers. Available in power steering. Mount bushings are included with the Power version, 

     

    POWER: Rebuilt power rack from 1982-88 T-bird. Also fits aftermarket Mustang II crossmembers. Bushings included. (Can be used with a Saginaw GM power steering pump without any additional valves or inline pressure regulators). Overall width is 45-1/8" with 15-1/2" mount centers. Must use offset bushings (910-34342) to mount to original Mustang II crossmembers. 3/4"-36 spline inp

  • Garage Sale - Mustang II Power Rack And Pinion
    Garage Sale
    Garage Sale - Mustang II Power Rack And Pinion
    x
                Please view the product's page for more information
            
  • Garage Sale - New T-Bird Power Rack for Mustang II Crossmembers
    Garage Sale
    Garage Sale - New T-Bird Power Rack for Mustang II Crossmembers
    x
                Please view the product's page for more information
            
  • Garage Sale - Mustang II Power Rack & Pinion
    Garage Sale
    Garage Sale - Mustang II Power Rack & Pinion
    x
                

    POWER: Rebuilt power rack from 1982-88 T-bird. Also fits aftermarket Mustang II crossmembers. Bushings included. (Can be used with a Saginaw GM power steering pump without any additional valves or inline pressure regulators). Overall width is 45-1/8" with 15-1/2" mount centers. Must use offset bushings (910-34342) to mount to original Mustang II crossmembers. 3/4"-36 spline input shaft.

    Instructions (PDF)  

     

    This is garage sale priced because it was damaged in shipping. 

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS 

  • Garage Sale - New T-Bird Power Rack for Mustang II Crossmembers
    Garage Sale
    Garage Sale - New T-Bird Power Rack for Mustang II Crossmembers
    x
                Please view the product's page for more information