Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 20

Products

Instrument Panel

Shop Street Rod Body, Interior & Gauges At Speedway Motors

Speedway Motors is the street rodder's source for body parts, gauges, and interior accessories! Find all the essential fiberglass body components, gauge sets by Stewart Warner and Auto Meter, and hot rod bomber seats, in our online catalog. While you are there, check out our full line of script emblems, rear view mirrors, windshields, fiberglass hoods and grilles. Complete your hot rod with sound proof insulation from Dynalite and Hushmat. Don't forget about Speedway's hot rod bomber seats for your traditional street rod, too!

Featured Products
  • Stewart Warner 82310 Deluxe Ammeter Gauge, 2-1/16 Inch, 30-0-30 Amps
    Stewart Warner 82310 Deluxe Ammeter Gauge, 2-1/16 Inch, 30-0-30 Amps
    (Part #66582310)
    x
                Stewart Warner Deluxe 2-1⁄16" diameter ammeter gauges feature a black face, white letters and chrome bezel. A 12 volt light is included.
            
  • Stewart Warner 82303 Deluxe 2-1/16 In Elec Fuel Level Gauge-240/33 Ohm
    Stewart Warner 82303 Deluxe 2-1/16 In Elec Fuel Level Gauge-240/33 Ohm
    (Part #66582303)
    x
                

    Stewart Warner Deluxe Series gauges feature black faces with white lettering, polished stainless steel bezels and back lighting for night time visibility.

    Individual Deluxe Series gauges do not come with sending units.

    • 12 Volt
    • 2-1/16" O.D.
    • Electric
    • Lighted back
    • Stainless bezel
    • Black face
    • Requires sender, (sold separately)

    Note: This gauge requires a sending unit operating from 33-240 ohms. Most GM senders are 0-90 ohms and will not operate the gauge correctly.

  • MSD 8952 LED Shift Light
    $118.99
    $147.99
    MSD 8952 LED Shift Light
    (Part #5478952)
    x
                The MSD Shift Light will turn on to œremind you to shift when the engine reaches your specified rpm. You select the rpm using the same plug-in modules that are used with your MSD Soft Touch Rev Control. The Shift Light features a bright cluster of LEDs making it easily visible, even in bright daylight. The light will also turn on for a second or two when the ignition switch is first turned on to inform you that the light is functioning properly.The Shift Light will work on 2, 4, 6 or 8-cylinder engines and will plug directly into the tach output on MSD 6, SCI, 7, 8 and 10 Series Ignitions or can be connected to the negative coil terminal when used with points or inductive-type ignitions. The MSD Shift Light is 4.5L x 3.5H with a 1.5 diameter lens. No rpm modules are supplied.

    Installation Instructions (PDF)

    • Speedway Liquid Filled Fuel Pressure Gauge
      Speedway Liquid Filled Fuel Pressure Gauge
      (Part #91011852)
      x
                  

      High quality, liquid-filled stainless steel fuel pressue gauge for remote mounting.

      • 0-15 psi
      • 1-3/4" face
      • 1/8" NPT connection

      910-11852 Instructions (PDF)

    • Gauge Replacement Light Bulb Kit
      Gauge Replacement Light Bulb Kit
      (Part #665366FK)
      x
                  Kit includes bulb, wire and socket. This fits a 5/8" light hole.
              
    • Auto Meter 2268 LS Series Oil Pressure Sender Adapter
      Auto Meter 2268 LS Series Oil Pressure Sender Adapter
      (Part #1822268)
      x
                  

      This LS Series oil pressure sender fitting allows your aftermarket 1/8" NPT oil pressure sending unit to be installed in place of the OEM oil pressure sender.

      When installing aftermarket gauges, the OEM oil pressure sender is not required by the PCM and may be replaced by the aftermarket sender of your choice.

    • MSD 7542 Adjustable Intensity LED Shift Light
      MSD 7542 Adjustable Intensity LED Shift Light
      (Part #5477542)
      x
                  

      Looking for a simple and small shift light that you can easily control the intensity of the LED? Here's the solution that plugs directly into your Programmable 7-Series Ignition.

      • For use with MSD programmable Digital 7 ignition control 
      • Adjustable intensity
      • LED shift light

      Installation Instructions (PDF)

    • Stewart Warner 82410-72 Dlx 2-5/8 Racing Oil Temperature Gauge, Mech
      Stewart Warner 82410-72 Dlx 2-5/8 Racing Oil Temperature Gauge, Mech
      (Part #66582410)
      x
                  

      Stewart Warner Deluxe Series 2-5/8" gauges are ideally suited for racing use with their large diameter, easy-to-read faces. The Deluxe Series features white lettering and pointer on a black face surrounded by a low profile stainless steel bezel. Gauge is back lit for excellent night-time illumination (bulb is replaceable).

      Includes a 72" capillary tube.

    Filter

    "Street Rod, Instrument Panel" Page 1 of 20

    Page 1 of 20

    • 1932 Ford Roadster Fiberglass Dash Panel, Filled
      1932 Ford Roadster Fiberglass Dash Panel, Filled
      (Part #9003217)
      x
                  

      Filled fiberglass dash panel for 1932 Ford Roadster. Features a glossy gelcoat finish that is ready for paint preparations.

      This product is usually in stock. However, if it is not, please allow three to four weeks for delivery. 

    • Speedway Fuel Level Gauge with Sender, 2-1/16 Inch
      Speedway Fuel Level Gauge with Sender, 2-1/16 Inch
      (Part #91065042)
      x
                  

      These fuel level gauge/sender kits feature a domed lens and a stainless steel bezel and a backlit white face.  The fuel sender comes with seal and and all mounting hardware.

      • 2-1/16”
      • Overall Diameter: 2.25"
      • Overall Length: 9.25"
      • Includes sender
      • 240 ohms empty, 33 ohms full
      • Stainless steel bezel
      • Backlit white face
      • Replacement light socket assembly available # 910-65071

      Learn more about selecting the proper fuel sending unit by reading our tech article, Fuel Sending Units.

    • Auto Meter 201009 Cobra Air-Core Voltmeter Gauge, 2-1/16 Inch
      Auto Meter 201009 Cobra Air-Core Voltmeter Gauge, 2-1/16 Inch
      (Part #182201009)
      x
                  

      This vintage instrument series is designed to accurately re-create the period correct details of the instruments used in the original Cobra Roadster while incorporating the latest technology advancements in performance gauges from Auto Meter. These black dial face instruments feature incandescent through the dial backlighting with white pointers, traditional numbers and tick marks, and are finished with flat glass and scalloped chrome bezels.

      • Short Sweep Electric Voltmeter
      • 8-18 V
      • Mounts in 2-1/16" Hole
      • Includes mounting hardware and Incandescent Backlighting
      • Requires 18 gauge electrical wire and ring or spade terminal connections for installation (not included)
    • Classic Instruments Speedometer Gauge Set, V8 Speedster Face
      Classic Instruments Speedometer Gauge Set, V8 Speedster Face
      (Part #2751018)
      x
                  

      Tom Gale, formerly Chief Designer of the Daimler Chrysler Corporation, has led the Classic Instruments design team in the production of a beautiful new series. Designed with unique dial faces that are spun and engine turned aluminum. The pointers for this series is a new design and each pointer is chrome painted. The face has a chrome V8 emblem signifying American Hot Rod Heritage. The light diffusers have laser etched indices lining up with the indices on the gauge faces.

      The V8 Red Steelie series features a vivid red background with spun aluminum numbers and accent graphics that brightly bounce off the red background. The series also features the uniquely designed pointer for the V8 line which is chrome plated and balanced for precision accuracy. Additional details within the instruments are laser etched markings on the light diffuser ring which add a level of dimension and functionality. The etching corresponds with the indices on the face and flow into a polished stainless high step bezel that is crimped around a optic grade curved lens to complete the overall design.

      • Black "V8 Speedster" face design or Red "V8 Red Steelie" face design
      • Kit includes 3-3/8" Speedo & Tach, 2-1/8" Fuel, Oil, Temp, Volts
      • Standard GM sender pack included

      Classic Instruments Installation Manual (PDF)

    • Speedway Electric Speedometer, 3-3/8 Inch Diameter
      Speedway Electric Speedometer, 3-3/8 Inch Diameter
      (Part #91065051)
      x
                  These electric speedometers are perfect for your rod or race project. They feature a white face with bold black lettering and a bright orange needle for quick monitoring.  Our 0-160 mph speedometers also come with a stainless steel bezel and a complete installation kit. This speedometer will work with either a 16 or an 8 ppm sender.  There are two calibration modes, the first of which asks you to drive a measured mile and the speedometer will detect the frequency of the sender. The other mode allows you to enter the pulses per mile of your sender.
      • 3-3/8” body diameter
      • 3-3/4 ” bezel
      • Overall Diameter: 3-3/4"
      • Body Length: 1.60"
      • Stud Length: 1.00"
      • Backlit white face with black lettering
      • Orange needle
      • Electric
      • 0-160 mph range
      • Stainless steel bezel
      • Includes installation kit
      • Compatible with almost any sender EXCEPT the Sky Driver GPS signal generator by Classic Instruments
      • SENDER NOT Included
      • Replacement light socket assembly available # 910-65075

      Instructions (PDF)

    • Classic Instruments AN80SHC All American Series Nickel Tach
      Classic Instruments AN80SHC All American Series Nickel Tach
      (Part #275202)
      x
                  

      Classic Instruments teamed up with Tom Gale, who was Chief Designer at Chrysler, to produce these beautiful gauges. They feature curved glass, polished stainless bezel, a raised logo and the vintage appearance you are looking for. The tach is 3-3/8".

       Classic Instruments Installation Manual (PDF)

    • Replacement Dash Light Bulb for 2-1/16 Inch Gauges
      Replacement Dash Light Bulb for 2-1/16 Inch Gauges
      (Part #91065072)
      x
                  

      Swap your burned out, broken, or faulty gauge bulbs in 2-1/16" size gauges with these replacement light bulbs.  They are a 3 watt bulb with in-line straight securing pins for use in most gauges and select speedometers and tachs.

      • Replacement dash/gauge bulbs
      • Fits 2-1/16" O.D. gauges
      • 12 volt
      • 3 watt bulb
      • Sold each
    • Auto Meter 1202 American Muscle 5 Piece Gauge Kit
      Auto Meter 1202 American Muscle 5 Piece Gauge Kit
      (Part #1821202)
      x
                  

      Auto Meter has hit a home run with their new American Muscle gauge kit. The distinctive look features LED illumination, glowing red pointers, chrome bezel and spun aluminum dials. The five gauge set includes a 3-3/8" electric speedometer and 2-1/16" water, oil, volt and fuel gauges.

      • Gauge Ranges: 160 MPH / 100 PSI / 100-250 deg. F / 8-18 Volts / 240ΩE-33ΩF
      • Tach (sold separately) operates on 4, 6, or 8 cylinder engines with points, electronic, and most 12V high performance racing ignitions

      Includes all sending units.

      In-Dash Gauge Installation Instructions (PDF)

    • Classic Instruments VT09GSLF-D Vintage Fuel Level Gauge
      Classic Instruments VT09GSLF-D Vintage Fuel Level Gauge
      (Part #275309)
      x
                  

      Requires tank-mounted sender #275235. 2-1/8" diameter.

      Vintage Series Gauges: feature 24 carat gold plated bezels, with parchment faces and brown numbers with old-fashion style red pointers.

      Classic Instruments Installation Manual (PDF)

    • Fuelab 71501 Fuel Pressure Gauge, 0-120 PSI
      Fuelab 71501 Fuel Pressure Gauge, 0-120 PSI
      (Part #91071501)
      x
                  

      FueLab mechanical fuel pressure gauges featurea black housing with a white face and black text.

      • For use on regulators or fuel rails with gauge ports
      • Direct mount 1/8” NPT fitting
      • 1.5” diameter gauge face
      • Not for use in passenger or driver’s compartments
    • 1937-38 Chevy 5-Gauge Dash Panel
      1937-38 Chevy 5-Gauge Dash Panel
      (Part #9100537)
      x
                  

      Brighten up your Chevy's dash and take advantage of modern instruments with these polished aluminum dash panels.  Gauge panels are set up for 3-3/8" speedometers and 2-1/16" accessory gauges.  Gauges sold separately. 

      Panels has a 3/16" lip around the back side of the whole panel to catch the opening in the dash

      910-0537

      • 4-1/16" x 11-7/8"
    • Dual Billet A/C Vent, 30 Degree Bezel
      Dual Billet A/C Vent, 30 Degree Bezel
      (Part #9103034)
      x
                  

      Give your dash some class with these distinctive oval-shaped A/C vents. They feature machined billet aluminum bezels with stainless steel vents for easy upkeep. Features dual-outlet vents and a 30-degree angle-cut bezel.

      Vents accept standard 2-1/2" A/C hoses and include brackets. Bezel measures 7-1/2" x 2".

    • Auto Meter 880088 Ford Series 3-1/8 Tachometer
      Auto Meter 880088 Ford Series 3-1/8 Tachometer
      (Part #1828888)
      x
                  

      Won’t this gauge look sweet in your Ford hot rod? This 3-1/8" diameter Auto Meter tachometer has a vintage look that includes the Ford logo. Features a vintage-style domed lens and white gauge face. Designed to mount into your dash.

      Operates on 4, 6, or 8 cylinder engines with points, electronic, and most 12V high performance racing ignitions.

      Tach Wiring Guide (Link)

       

       

    • Stewart Warner 82307 2-1/16 Inch Deluxe Electric Water Temp Gauge
      Stewart Warner 82307 2-1/16 Inch Deluxe Electric Water Temp Gauge
      (Part #66582307)
      x
                  Stewart Warner Deluxe Series gauges feature black faces with white lettering,  polished stainless steel bezels and back lighting for night time visibility.

      Individual Deluxe Series gauges do not come with sending units.

    • 1932 Ford Dash Panel
      $129.99
      Product Rating: 5.00 Stars
      1932 Ford Dash Panel
      (Part #91139530)
      x
                  

      These beautiful billet aluminum dash panels are the perfect finishing touch for your interior. AutoMeter gauges. These are held into a factory dash or equivalent fiberglass dash with four tabs that attach to the back of the billet panel with 4 machine screws, which are included. This billet panel sits down into the recess lip of the factory or aftermarket dash. 

      This panel features three drilled and recessed holes that can be used for mini LED indicator lights. The inside diameter of the hole is 5/32" and the recess around the hole is nearly 1/4" wide for the light bezel around the bulb. The three holes would serve for high beam indicator, and left and right turn indicators. 

      Entire thickness of this panel is 3/8" with 1/4" going through the dash opening and the remaining 1/8" being the lip that sits into the factory style recessed lip of the dash. 

    • Omega Kustom 930233 8000 RPM Tachometer, 3-3/8, Black Face
      Omega Kustom 930233 8000 RPM Tachometer, 3-3/8, Black Face
      (Part #91093033)
      x
                  

      Omega Kustom tachometers are made in the U.S.A. with a 3 year warranty. Features a stainless steel bezel, anti-scratch glass lens, precision movements, plastic case, and adjustable brackets.

      Omega Tach Gauge Installation Instructions (PDF)

      Gauge Mounting Information (PDF)

    Goto Previous PagePrevious Page
    1 2 3 4 5 ... 20