Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products

Speedway Motors stocks all the best names in street rod carburetors and intake manifolds! Plus, we have a great selection of fuel cells, as well as electric and mechanical fuel pumps. Don't forget to let your engine breath with filters from K&N and R2C. Whether you run alcohol or gas in your hot rod, Speedway can fuel your need for speed!

"Street Rod, Fuel Storage" Page 1 of 15

  • JAZ Products 300-000-20 Fender Mount Fuel Filler Kit
    JAZ Products 300-000-20 Fender Mount Fuel Filler Kit
    x
                

    For remote filling of fuel cell. Kit contains a 12-bolt recessed fender fill assembly with vented cap (1/2 turn, twist & lock style). Fender filler flange measures 6-1/4" outside diameter.

    Cap and base are made of galvanized steel. Fill and vent hose are clear polyethylene. Use with fast fill valve.

  • Fuel Tank Roll-Over Vent Valve
    Fuel Tank Roll-Over Vent Valve
    x
                

    This safety device will automatically stop fuel flow if your car somehow gets upside down. Inside is a needle/ball seat which stops fuel flow out the vent if you get upside down.

    • Accepts 5/16" hose
    • Fits into 1/4" npt port
    • Measures 3" bottom-to-top
  • Aeroquip Special Application Socketless AN Hose, Black
    Aeroquip Special Application Socketless AN Hose, Black
    x
                
  • Textile braid reinforcement
  • Low pressure design for use with socketless reuseable fittings only
  • No hose clamp necessary
  • Ideal hose for fuel line applications
  • 50,000 ft of hose in stock!
  • Construction: AQP elastomer tube, textile braid reinforcement, black AQP elastomer cover.

    Application: For gasoline, fuel and lubricating oils, air and water. Not recommended for hydraulic impulse applications and is not approved for air brake, hydraulic brake or power steering applications.

    Operating Range: Max Operating pressure: 250 PSI. Minimum burst pressure: 1000 PSI. Operating Temperature Range -40°F to 300°F. Air not to exceed +250°F and water not to exceed +180°F. Reduced pressure operation allows for temperatures up to 300°F.

    Aeroquip Hose Sizing Guide (GIF)

    Hose Fitting Sizing Chart (GIF)

  • Spun Aluminum Fuel Tank, 11 Gallon, 10 x 33 Inch, Offset Outlet
    Spun Aluminum Fuel Tank, 11 Gallon, 10 x 33 Inch, Offset Outlet
    x
                

    These spun aluminum tanks have an unpolished, spun aluminum finish, 2-1/4" neck, and a 1/4" NPT female outlet. For all off-road vehicles. The screw-on vented cap and brackets are included and can be found in a false bottom of the packaging box.

    This tank features a fuel outlet that is 3" from the end opposite the filler neck.

  • Aircraft Style Fuel Filler Neck & Cap
    Aircraft Style Fuel Filler Neck & Cap
    x
                

    Flush-mount caps offer excellent aerodynamic performance, large fill opening and attractive appearance. Cap features a positive seal, flip-up 1/4-turn handle, and a chain to secure it to the gas filler neck. Includes cap, chain, fuel filler neck, gasket, and all hardware. Polyethylene cap is vented.

    Hole in tank needs to be 3-3/4" for cap to sit flush.

  • Chrome Plated Stainless Steel Flush Mount Fuel Fill
    Chrome Plated Stainless Steel Flush Mount Fuel Fill
    x
                

    This chrome plated stainless steel fuel fill can be flush mounted and includes a special opening key. Simple three hole mounting makes installation a snap.

    Use with 1-1/2" I.D. hose (sold separately).

  • Black Straight -6 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    Black Straight -6 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    x
                

    These straight flare adapters connect 3/8" pipe to straight -6 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Black finish will give your engine compartment the look you are after.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fuel line hose connector
    • -6 AN to 3/8" aluminum pipe adapter
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Black anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Filler Twist Cap with Steel Neck
    Filler Twist Cap with Steel Neck
    x
                

    These filler necks come with a vented cap which vents to the underside of the cap. Steel weld-in 2.25" O.D. bung. Cap locks on the inside of the neck, not on the outside like a radiator cap.

  • Aeroquip Special Application Socketless AN Hose, Blue
    Aeroquip Special Application Socketless AN Hose, Blue
    x
                
  • Textile braid reinforcement
  • Low pressure design for use with socketless reuseable fittings only
  • No hose clamp necessary
  • Ideal hose for fuel line applications
  • 50,000 ft of hose in stock!

    Construction: AQP elastomer tube, textile braid reinforcement, blue AQP elastomer cover.

    Application: For gasoline, fuel and lubricating oils, air and water. Not recommended for hydraulic impulse applications and is not approved for air brake, hydraulic brake or power steering applications.

    Operating Range: Max Operating pressure: 250 PSI. Minimum burst pressure: 1000 PSI. Operating Temperature Range -40°F to 300°F. Air not to exceed +250°F and water not to exceed +180°F. Reduced pressure operation allows for temperatures up to 300°F.

    Aeroquip Hose Sizing Guide (GIF)

  • Hose Fitting Sizing Chart (GIF)

  • JAZ Products 200-016-NF Polyethylene Fuel Cell, 16 Gallon
    JAZ Products 200-016-NF Polyethylene Fuel Cell, 16 Gallon
    x
                

    These polyethylene fuel cells are the best cells on the market! This 100% seamless polyethylene cell features one -8 AN pick-up fitting and one -8 AN vent/tip-over valve fitting. These fuel cells contain a pickup tube. All cells are NHRA, IHRA, SCORE, and DIRT approved.

    • Seamless cross-linked polyethylene outer shell 
    • D-ring bail handle cap assembly
    • 360 degree mouting strap recesses
    • Does not include fuel cell safety foam
  • Steel Weld Bung for 1 Inch I.D. Tube, 3/4-16 RH
    Steel Weld Bung for 1 Inch I.D. Tube, 3/4-16 RH
    x
                

    Heavy duty steel weld bungs for splitting wishbones, custom tie rods or custom suspension control arms. These weld bungs are 1” O.D. where they slide into the steel 1" I.D. tubing.

  • Polyethylene Fuel Cell Mounting Straps, 16 Gallon
    Polyethylene Fuel Cell Mounting Straps, 16 Gallon
    x
                

    Zinc-plated steel mounting straps available for 16 gallon seamless polyethylene fuel cells (non-steel can cell design).

    NOTE: These straps do not work with steel can fuel cells.

    Must be used with cell #s 458-116 or 458-0458 only

  • Speedway Fuel Cell Foam, 14 x 4 x 6 Inch
    Speedway Fuel Cell Foam, 14 x 4 x 6 Inch
    x
                

    Compatible with gasoline, E85, or alky fuels (not recommended for use with nitro-methane). This fuel cell safety foam keeps weight transfer/shift to a minimum, which provides you with more responsive and predictable handling. Can be cut and stacked as needed.

    • 8-12 gallon cells typically use 3-8 sticks
    • 16 gallon cells typically use 4-10 sticks
    • 22-32 gallon cells typically use 8-14 sticks

    Blocks are sold EACH.

  • Straight Chrome Fitting, 3/8 Inch Hose to 3/8 Inch NPT
    Straight Chrome Fitting, 3/8 Inch Hose to 3/8 Inch NPT
    x
                

    These chrome plated push-on brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb ends
    • 3/8" Hose to 3/8" NPT adapter
    • Fuel line hose connector
    • Straight angle
  • Black Straight -6 AN Flare to 1/4 Inch NPT Pipe Adapter Fitting
    Black Straight -6 AN Flare to 1/4 Inch NPT Pipe Adapter Fitting
    x
                

    These straight flare adaptors connect 1/4" pipe to straight -6 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Black finish will give your engine compartment the look you are after.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fuel line hose connector
    • -6 AN to 1/4" aluminum pipe
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Black anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Fuel Tank Sealer, Quart
    $27.99
    Product Rating: 4.75 Stars
    Fuel Tank Sealer, Quart
    x
                

    This tank sealer seals gas tanks, aluminum, and even rusty steel. Not affected by fuel additives, octane boosters, ATF hydraulic fluid, brake fluid or oil. Remains flexible. One quart.

    • STAYS FLEXIBLE – Will never crack or peel off.
    • ALCOHOL RESISTANT – No expensive come-backs.
    • BRIGHT BLUE COLOR – Both you and your customer can see results.
    • COVERS RUST – Seals old rust in and prevents future rusting.
    • SEALS LEAKS – Gets the multitude of pin-holes you can’t find.

    *Cannot Ship By Air*

    910-16752 Instructions (PDF)

    Tank Sealer FAQ (PDF)

    Material Safety Data Sheet (PDF)

     

     

  • Professional Products 10415 Holley 4150 Dual Feed Fuel Line Kit, -8 AN
    Professional Products 10415 Holley 4150 Dual Feed Fuel Line Kit, -8 AN
    x
                These dual feed fuel line kits give you the looks, performance and flexibility your car deserves. Fuel log features -8 AN inlet, 1/8" NPT tapped fuel pressure gauge port, and allows you to have a fuel tank return if needed.

    Fuel line fits Holley 4150 style Double Pumper carburetors with 7/8"-20 inlets.

  • Straight Chrome Fitting, 5/16 Inch Hose to 1/4 Inch NPT
    Straight Chrome Fitting, 5/16 Inch Hose to 1/4 Inch NPT
    x
                

    These socketless chrome plated brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb connector
    • 5/16" Hose to 1/4" NPT adapter
    • Straight angle
  • Aluminum -8 AN Female to -6 AN Male Reducer Fitting
    Aluminum -8 AN Female to -6 AN Male Reducer Fitting
    x
                

    Aluminum female to male adapter for 37° AN pipe fittings. Blue anodized finish.

    • -8AN female to -6AN male fuel line hose connector

    Fitting Thread Application Chart (GIF)

  • 1-1/2 Inch Aluminum Remote Fuel Cell Filler Neck Flange Assembly
    1-1/2 Inch Aluminum Remote Fuel Cell Filler Neck Flange Assembly
    x
                

    These filler necks are manufactured from top-quality materials and are available in two sizes to best suit your application. You can count on these fuel cell filler necks to complete your performance fuel setup.

    1-1/2 Inch Aluminum Remote Fuel Filler Neck Flange Assembly 

    • O.D. of flange is 5-1/16"
    • 6 mounting holes on a 4.36" bolt circle
    • Filler neck is 1-1/2" O.D.
    • Includes mount ring, bolts and gasket

    This flange bolts to your fuel cell to permit attachment of a 1-1/2" I.D. filler hose. Aluminum construction.

  • Garage Sale - Total Performance 11 Inch Windshield Slug, With Hole
    Garage Sale
    Garage Sale - Total Performance 11 Inch Windshield Slug, With Hole
    x
                

    Aluminum windshield slug material designed for Total Performance's round tube "T" style windshields.  This slips inside the tubing to allow you to attach hinges, glass clips and the frame to the posts.

     

    This is garage sale priced because it has been discontinued.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS   

  • Aeroquip FBG0600 FC300 High Pressure Hose, -6 AN, Per Ft.
    Aeroquip FBG0600 FC300 High Pressure Hose, -6 AN, Per Ft.
    x
                

    Aeroquip FC 300 hose is designed for high pressure fluid applications such as power steering line. The FC300 hose features a blue, abrasion-resistant fabric cover over a synthetic rubber inner tube for longer life. This high pressure hose is ideal for power steering, hydraulics, air, fuel and lubricating oil applications.

    • Max operating pressure is 2250 psi
    • Minimum bend radius is 4"
    • Temperature range of -55°F to +300°F
    • Hose is sold by the foot

    Note: The FC300 Hose only works with FC300 steel fittings (not included). Easily assembles with a bench vise and/or wrenches. Ends are reusable.

    AN Thread Sizing Guide (GIF)

    AN 6 Hose Application Chart (GIF)

  • Straight Chrome Fitting, 3/8 Inch Hose to 1/4 Inch NPT
    Straight Chrome Fitting, 3/8 Inch Hose to 1/4 Inch NPT
    x
                

    These chrome plated brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb end
    • 3/8" Hose to 1/4" NPT adapter
    • Straight angle line connector

     

  • Chrome 90   Adapter Fitting, 3/8 Inch Hose to 1/4 NPT
    Chrome 90 Adapter Fitting, 3/8 Inch Hose to 1/4 NPT
    x
                

    These chrome plated brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb ends
    • 3/8" Hose to 1/4" NPT
    • 90 Degree angle
  • Aeroquip Straight Full Flow Swivel Hose End Coupler Fitting, -6 AN
    Aeroquip Straight Full Flow Swivel Hose End Coupler Fitting, -6 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a red and blue anodized finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617306).

    • -6 AN female to push-on style adapter
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • Unique taper design ensures easy assembly
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Accepts a variety of lightweight aluminum AN style adapters & fittings
    • Works great with custom fuel lines
    • Available in Red/Blue corrosion resistant finish

    Straight full flow ends come in sizes of AN4, AN6, AN8, AN10, AN12, and AN16.

    Fitting Thread Application Chart (GIF)

  • Spun Aluminum Fuel Tank, 11 Gallon, 10 x 33 Inch, Centered Outlet
    Spun Aluminum Fuel Tank, 11 Gallon, 10 x 33 Inch, Centered Outlet
    x
                

    These spun aluminum tanks have an unpolished, spun aluminum finish, 2-1/4" neck, and a 1/4" NPT female outlet. For all off-road vehicles. The screw-on vented cap and brackets are included and can be found in a false bottom of the packaging box.

  • Straight Aluminum Bulkhead Flare Fitting, Blue, -6 AN
    Straight Aluminum Bulkhead Flare Fitting, Blue, -6 AN
    x
                

    Straight aluminum bulkhead fitting for 37° AN flare. Blue anodized.

    AN Thread Sizing Guide (GIF)

    Fitting Thread Application Chart (GIF)

  • Aluminum Bulkhead Jam Nut, Blue, -3 AN
    Aluminum Bulkhead Jam Nut, Blue, -3 AN
    x
                

    Aluminum bulkhead jam nuts for AN fittings. Blue anodized finish.

    AN Thread Sizing Guide (GIF)

    Fitting Thread Application Chart (GIF)

  • Spun Aluminum Fuel Tank, 9-1/2 Gallon, 10 x 28-1/2 Inch
    Spun Aluminum Fuel Tank, 9-1/2 Gallon, 10 x 28-1/2 Inch
    x
                

    These spun aluminum tanks have an unpolished, spun aluminum finish, 2-1/4" neck, and a 1/4" NPT female outlet. For all off-road vehicles. The screw-on vented cap and brackets are included and can be found in a false bottom of the packaging box.

  • Steel -6 AN Fitting for Aeroquip FC300 High Pressure Hose, 90 Degree
    Steel -6 AN Fitting for Aeroquip FC300 High Pressure Hose, 90 Degree
    x
                

    Steel power steering hose end fitting for use with Aeroquip FC300 high pressure hose. 90° elbow -6 AN swivel fitting easily assembles onto -6 AN hose with a bench vise and/or wrenches.  Steel hose ends are reusable.

    • -6 AN female to push-on adapter
    • 90° elbow fuel line hose connector
    • 37° angled sealing surface guarantees a positive anti-leak seal

    Fitting Thread Size Chart (GIF)

    FC300 Assembly Chart (GIF)

  • Aluminum Flare Fitting Plug, Blue, -6 AN
    Aluminum Flare Fitting Plug, Blue, -6 AN
    x
                

    Aluminum flare plugs. 37° AN.

    Fitting Thread Application Chart (GIF)

  • Nickel Straight Flare to Aluminum Pipe Adapter Fitting, -6 AN to 3/8 Inch NPT
    Nickel Straight Flare to Aluminum Pipe Adapter Fitting, -6 AN to 3/8 Inch NPT
    x
                

    Many street rodders find that red or blue anodized aluminum AN hose fittings look too racy on their cars, but standard steel versions are just too plain.

    Speedway offers a great looking alternative with these nickel plated aluminum hose fittings and adapters from Aeroquip. Lighter and more affordable than stainless steel, these electoless nickel plated pieces combine great corrosion resistance with a neutral color and classy appearance.

    These straight flare adaptors connect 3/8" pipe to straight -6 AN fittings. They are lightweight and feature a 37° sealing angle. 

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum connector fitting
    • -6 AN to 3/8" aluminum pipe adapter
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in nickel plated finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Russell Performance 639200 3/8 Inch Tubing - AN 6 Female Flare Adapter
    Russell Performance 639200 3/8 Inch Tubing - AN 6 Female Flare Adapter
    x
                

    Tubing to AN flare adapters are for use with aluminum tubing only (not steel tubing). 

    • Connects 3/8" aluminum tube to -6 AN adapters
    • Unique crimp design eliminates tube flaring
    • Not for use with fuel injection

    Learn more about flaring lines and how to select proper automotive fittings by reading our tech article. The Principles of Automotive Fittings.

  • Hagan Street Rods 45 RF 45 Degree Flat Series LH Hinge Round Fuel Door
    Hagan Street Rods 45 RF 45 Degree Flat Series LH Hinge Round Fuel Door
    x
                

    Now you can make that old gas tank filler neck and cap go away with this easy flush mount gas door kit. Just select the style that would best fit to the surface and choose the design of the gas door with the hinge mount on the left or right side. This has a fuel spout that is 2" OD to accept a 2" ID fuel hose of your choice. Fuel hose not included.

    • Can be mounted in steel or fiberglass
    • Made of 18 gauge mild steel
    • Hinge is spring loaded to hold the door open and closed
    • Latch is spring loaded and magnetic
    • Includes housing, door, hinge, latch, gas cap, spout and install instructions
    • Door is 3-1/2" round
    • The top is made of 18 gauge mild steel
    • The spout is 2" O.D. and 3-3/4" long
    • Overall depth of unit is 3"
    • Shipping weight is 3.011 lbs.
  • Female Aluminum Swivel Coupler Fitting, -6 AN
    Female Aluminum Swivel Coupler Fitting, -6 AN
    x
                

    Female aluminum swivel coupler for 37° AN fittings.

    • -6 AN female adapter
    • Straight style fuel line hose connector
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Red/Blue corrosion resistant finish

    Fitting Thread Application Chart (GIF)

  • JAZ Products 250-008-NF Bottom Sump Fuel Cell, 8 Gallon
    JAZ Products 250-008-NF Bottom Sump Fuel Cell, 8 Gallon
    x
                This bottom sump fuel cell is perfect for all race applications.  8 gallon capacity.  Flush mounted aerospace type filler neck.  Internal 2" sump with two AN 8 pick-up fittings.  An auxiliary AN 6 vent or return line is on the top.  Measures 20" long, 15" wide and 7-1/2" deep.

    Tech Tip: Carefully determine the size of fuel cell needed. Depending on the capacity, a full fuel cell will generally weigh between 100 and 200 lbs. Buy the optimum size fuel cell to best accommodate weight bias and fuel consumption.

Goto Previous PagePrevious Page
1 2 3 4 5 ... 15