Speedway Motors is your one stop shop for hot rod wiring and lighting. Make wiring your hot rod simple with easy to use wiring harnesses and step by step instructions. Finally finish off your street rod project with specialty headlights, LED dome lights, and blue dot glass tail lights. Find anything on the online catalog and let Speedway Motors eliminate any and all of your hot rod electrical system problems!
Polished stainless steel headlights feature a 12 volt H5 quartz halogen bulb (high & low beams) behind original style lens with mounting stud. Light is 10" diameter.
This module combines all of the functions of the Self-Canceling Turn Signal Module and the Tri-Star Module. Engineered for the custom builder or to retro-fit motorcycles not equipped with self-canceling turn signals. Designed for use with individual momentary type turn signal switches mounted on the left and right handle bars.
- Has 3 timing modes: self canceling, hazard mode, non-self canceling
- Adds brake light function to turn signals
- Non-load dependent flash duration: all three modes are flash time constant whether using incandescent or LED lighting
- Dependable solid-state electronic components
- Weather proof - potted with soft cell technology to prevent wire chaffing and damage
- Requires only one taillight bulb per side
910-64070 Instructions (PDF)
There is nothing cooler than a mean looking car with frenched headlights. This kit includes all the hard parts needed to install such as the headlight buckets, stainless retaining and trim rings, adjusting assembly and hardware. These buckets require welding and body work to be finished.
These headlight buckets work best with sealed beam lights like a Sylvania 6014. They will work with tri-bar lights by opening up the hole in the back side of the bucket.
For 7" headlights. Lights sold separately.
- The latest in electronic speedometer senders
- Simple 4-wire hookup
- Completely sealed
- GPS triangulation gives true ground speed
- No calibration necessary
- For 8 or 16 pulse
- Must be mounted face up
- Clear view of sky is best unit can be mounted under dash/hood
- Must have minimum of 3" clearance between top of unit and steel
"Street Rod, Electrical, Lighting and Body" Page 1 of 16
Modern Driveline Reverse Switch Harness for GM T5 and T56 Transmissionsx
These harnesses for transmission neutral safety switch/reverse light switches are designed for use with GM T5 and T56 transmissions.
- Factory style
- For GM T5 and T56 transmissions
$79.99More InfoTall Model T Cowl-Tail Lights, Blackx
Features a 12 volt dual element bulb and can be used as a tail light or a cowl light. 9-1/2" tall with 3" diameter lens. Specify red or amber lens.
Note: Mount bracket is NOT included. Lens must be secured in place with silicone (see Instructions).
$129.99More Info1928-29 Dropped Stainless Headlight Barsx
1928-1929 Dropped style stainless steel headlight bars. Polished.
Top width (flange tip to flange tip) 42-1/2"
Bottom width (flange tip to flange tip) 38-1/2"
$19.99More InfoUniversal Headlight Mountx
- 5/16" mounting holes 2" center to center
- 1/2" ID sleeve for light mounting bolt
- Great for headlights and taillights
- Use with mounting cups 91061034
$19.99More InfoSafety Kill Switchx
This is the best kill switch we've found! Works with standard ignition only. Water resistant with O-ring shaft seal. Pull on, push off with silver contacts.
20 amp rating at 12 VDC.
$44.99More Info1932 Ford Tail Light Bracket, Chromex
These 1932 Ford tail light brackets are stamped steel reproductions. They feature a beautiful chrome plated finish. Choose left or right side.
- 1932 Ford passenger cars
- Chrome plated finish
- Stamped steel reproductions
- Specify left or right side
$6.99More InfoPainless Wiring 70402 Two Wire Weatherpack Connectorsx
A real water-tight connection. Each number consists of one male and one female component. Accepts 14 - 16 gauge wire.
$28.99More Info1954 Chevy Tail Light Chrome Bezel with Screwsx
These tail light bezels for 1954 Chevy passenger cars replicate those of the original and feature a chrome plated finish.
- Beautiful chrome plated die cast bezel
- Comes with 6 mounting screws
- Duplicate of original
- Left or Right Side
- Fits All Passenger Cars
$94.99More InfoUniversal Electric Window Switchx
- Fits All Vehicles
- Includes 5 Shafts to Fit All Window Cranks
- 15 Degrees Up Or Down Activates The Switch
- Billet Aluminum
- Dead Lock Stop Design Will Not Break
- Works With All Power Window Systems
- Ultra Thin Design
- Designed In The USA
- Manufacturer Lifetime Warranty
- Smallest System On The Market
$9.99More InfoHagan Dummy Load Resistors for LED Lightsx
When installing LED lights, you may need to use a dummy load resistor to increase the amps drawn by the LED on the turn signal flasher to make it work properly.
- Increase the amps drawn by the LED
- Turn signal flasher
- 12 Volt source
- The dummy loads should be installed parallel, with one LED turn/hazard bulb on each side.
- Simply splice the dummy load into the power wire for the LED and a good ground source.
- This must be done for one lamp on each side of the vehicle.
$29.99More InfoStainless License Plate Lightx
- Fully polished stainless steel housing
- 12 volt operation
- Mounting hardware included
- Uses common replaceable wedge-type dashlight bulb
Stewart Warner 82629 GM Speedometer Sender Gear Drive Tip - .104 Inchx
Stewart Warner square drive tip to attach sender gear (part number 66582623B) to a GM transmission.
- .104 Inch drive tip
$10.99More InfoUniversal Specialty Light, Double Filament Bulb, Amber Lensx
Double filament bulbs work great for custom taillights, brake or turn signals. Chrome housing measures 2-1/2" long and 1-3/4" wide. Wires feed through a 3/8” bolt that threads into the main housing. The chrome washer and rubber washer are 7/8” O.D.
This accessory light uses double filament replacement bulb 316-2012.
$119.99More Info1930-31 Ford Model A Dropped Headlight Bar, Stainlessx
These dropped style stainless steel headlight bars are for 1930-1931 Fords. They feature a 4 inch drop and connect fender to fender to support your headlights, just like the originals. These bars come with a highly polished stainless finish.
- 1930-31 Fords
- Top width (flange tip to flange tip) 43"
- Bottom width (flange tip to flange tip) 38-3/4"
- 43-1/8" Long
- OEM # A-13114-BD
- Highly Polished Stainless Steel 4" Dropped Headlight Bars for Street Rods
Note: If you intend to use this light bar on your 1930-31 Model "A" using a 1932 grille shell and insert, it will require considerable modification. The 1932 grille insert has a "V" shape, while the 1931 grille does not. The modifications required include cutting, welding, bending and polishing.
$12.99More Info1938-1939 Ford Tail Light Frenching Bucketx
These all steel buckets allow you to "French" your 1938-1939 Ford tail lights into the body. Welding & bodywork required.
$69.99More InfoMechanical Speedometer Universal Dash Gauge Harnessx
If you want to keep your under-dash area organized or you think that you will need to remove gauges from time to time, then you need to install this universal gauge harness. It will connect to all major brand gauges including Auto Meter and VDO and works with most dash layouts and sizes.
Includes all connections for volt meter, oil pressure, temperature, tachometer, and fuel gauges, plus high beams and turn signals. Plus, the purpose of each wire is printed directly on it for a fool-proof installation.
- Fits all dash layouts
- Omega style harness
- Color coded and labeled for intended circuit
- Note: excludes Speedo sender wiring
One harness has 9 wires that are 18-1/4" long and the other harness has 26 wires with the longest wire 30-3/4" long .
$8.99More InfoUniversal Windshield Wiper Switch for Single Motorx
These easy-to-use universal windshield wiper switches feature OFF/PARK, LOW and HIGH and are for use with single motor wiper set-ups.
- 3-position switch
- Requires a 7/16" mounting hole
- (4) blade style terminals
910-64056 Instructions (PDF)
$8.99$14.50More InfoTitan Tools 45227 96-Piece Blade Fuse Assortmentx
- 1 resealable plastic case
- 12 of each of the following ATO fuses:
- 3A violet
- 5A Orange
- 4.5A Brown
- 10A Red
- 15A Blue
- 20A Yellow
- 25A Clear
- 30A Green
$49.99More InfoModel T Cowl or Tail Light Brackets for 9-1/2 Inch Lampx
Mounts to side of 9-1/2" tall lamps and any flat surface. Conceals wiring. Available in brass or chrome.
Note: This is the bracket only (hardware NOT included).
$9.99More InfoHeadlight Cone Mounting Cupsx
Headlight cone mounting cups for universal headlight mount 91061026.
$8.99More InfoLED 1157 Tail Light Bulb, 1 Inch, Redx
These LED tail light bulbs put out the light you're after, but don't get hot like normal bulbs. 1157 bulbs have staggered pins and 2 contacts on the plug. The bulbs appear to be clear, but are red when illuminated.
LED taillight bulbs are quite efficient and use such small amounts of power that a normal flasher will not work correctly. The use of LEDs will almost always require the use of a special "low load" flasher like our 910-64110 (2-prong) or 910-64112 (3-prong.)
$157.99$174.99More InfoAtomic EFI Installation Kit for GM LS1/LS6 Enginesx
These kits complement the Master Kits and provide the necessary brackets and injector connectors to complete an install for LS1/LS6 and LS Trucks. These kits provide different brackets for the rail assemblies as well as different injector connectors to adapt the LS2/3 Master Kit to work on the LS1/LS6 and truck intakes.
- For LS1/LS6 Atomic Installations
- Must use with 2950 Atomic LS Master Kit
- Includes brackets and injector connectors
- Uses EV1 Injector Harness
$58.99More InfoBillet Interior Courtesy Dome Light, Standard Bezelx
Add subtle style and soft illumination to your interior with these oval-shaped interior courtesy dome lights. They feature standard radius billet aluminum bezels and contoured lenses, with LED lights providing gentle, white light. Light is machined from a solid piece of billet aluminum and houses six 5mm cool white L.E.D's. behind a dome shaped lens.
12 Volt 7 Inch Round Hi/Low Sealed Beam Headlight, Replacement Bulbx
12 Volt Round 7" sealed beam hi/low replacement headlight for 7" Dietz type headlight.
These sealed beams feature custom-designed glass lenses that are manufactured to each specific application. They use a non-reflective bottom shelf for increased lamp effectiveness in rain, snow, and fog. A special grinding process on the aiming pads forms a perfect plane, making headlight aiming an easy process. They feature high-grade brass terminals and a glass exhaust tube.
This is a replacement headlight for the standard 7” Dietz type, seal beam number 6014.
Hi/Low Replacement Headlight
- Round, 7" O.D.
- 12 Volt
$39.99More InfoLED Cat Eye Tail Lightx
This 12-volt, 12-LED tail light can be used as a stop/turn/tail or just use as a third stop light. Measures 7.25" long x 1-50" tall x .730" thick with a chrome bezel. Light is flat on the back side and comes with a mounting gasket.
10-32 mounting bolts (not) included.
$14.99More InfoDesk Flag Setx
Perfect for the racer or fan who has everything. Also ideal for promotions or awards. 7 flags mounted on pine base. 12" long x 10" tall.
$22.99More Info1928-1931 Ford Model A Stainless Tail Lightsx
Polished stainless steel housing with glass lenses. An excellent replacement or addition to your Model 'A' Ford. Left tail light has lenses on the bottom to illuminate a license plate. Choose left or right. 12 volt operation.
- 3.851" diameter
- 3" depth
- 3.851" height
- 1-3/4" mount
- Housing - Ground
- Tail - Black
- Stop - Green
These tail lights have two bulbs in them that are of a single filament style.
$44.99More InfoPainless Wiring 30805 GM Steering Column Pigtail Kitx
Steering column pigtail kit lets you use factory-type connectors on your key-switch-equipped GM-style column.
This kit is used to make the connection from the wiring harness to GM and Ididit columns. It can be used to replace damaged or worn plugs. The supplied GM color-coded wires are 12" long, so you'll have plenty of room to splice to your harness.
- ignition connector
- turn signal connector
- dimmer switch connector
- pre-terminated 12" pigtails
$4.99More InfoFan/Shroud/Cooler Mounting Kitx
This mount kit consists of 4 threaded plastic bolts 3/16" diameter and approx. 8-1/2" long. Also includes 4 1/4" spacers, 8 thin washers, and 4 metal wingnuts.
Works great for mounting your fan shroud, electric fan, or oil cooler directly to your radiator.
$5.99More InfoPainless Wiring 40008 Four Wire Quick Connect Terminalx
Make your own locking quick connect plugs easily and quickly. Each kit contains one male and one female component. Accept 10 - 20 gauge wire.
$5.99More Info1932 Ford Headlight Bar Bolt, Stainlessx
Headlight bar bolt for 1932 Ford. Measures 1.700" from shoulder to the end of the threads. Thread length is 1.185".
$121.99More InfoPainless Wiring 30001 Universal 12 Circuit Fuse Blockx
Use this Painless 12 Circuit OEM style pre-wired fuse block to replace your existing fuse block or as a starting point for custom wiring. All you have to do is terminate your circuit wire and attach it to the fuse block. Pre-wired and labeled for the following circuits: A/C-Heat, gauges/dash instruments, brake lights, headlights, coil, horn, dome lights, radio, electric fan, turn signals, hazards, wipers and alternator.
Has accessory outlets, offers a compact size and includes easy-to-follow instructions makes any job painless. Kit includes mounting bracket, fuses, flashers, horn relay, terminals and full instructions.
$30.99More InfoLokar EHB-7001 Emergency Brake Warning Light Switchx
This emergency brake warning switch kit triggers your dash light or buzzer to alert you when your emergency brake is engaged.
Kit includes a switch, stainless trigger, 2 electrical terminals, e-clip and pin and 2 mounting bolts.
Works with floormount hand brake levers only (491-7000 & 491-07000).
$9.99More InfoTridon Replacement Turn Signal Flasher Unit, 3-Prongx
These state-of-the-art electronic flashers work with standard bulbs. 12 volt operation (will not work on 6 volt systems). Made in the U.S.A.
- Replacement for turn signal
- Works with standard bulbs
- 12 volt operation only
- Made in the U.S.A.
- The X terminal is the + 12v input
- The P terminal output drives the flasher indicator
- The L terminal drives the load (bulbs)
Note: We recommend the use of our grounded LED flashers for use with LED's (910-64112 3-prong).
$69.99More InfoLokar SP-1500U GM Speedometer Drive Cable Kit, Blackx
The finishing touch to your mechanical (cable-drive) speedometer installation in your GM or Mopar. Includes a 7 ft. long glossy black vinyl housing and inner cable (you trim to length) with billet aluminum ends, and instructions.
Works with all cable-drive aftermarket and original equipment speedometers that have a male 5/8"-18 thread connection. Has a 7/8"-18 end for the transmission.
$39.99More InfoFlex-A-Lite 31147 Adjustable Electric Fan Control Kitx
This kit lets you make any electric fan thermostatically controlled. Just turn a knob to change activating temperature from 170°-240° F. Complete kit includes adjustable temperature control, 2' capillary tube, wire, terminals, and instructions.
All electric fans and related components are 12 volt only.
910-64014 Instructions (PDF)
$5.99More InfoMSD 8985 Timing Tapesx
MSD's timing tape set comes with eight different tapes to fit balancers from 5-1/4" to 8" diameters.
$6.99More InfoUniversal Mechanical Brake Light Switchx
Our mechanical brake light switch is "closed" in the at rest position. It breaks the circuit when pushed. Mounts near your brake pedal and the arm can be bent as needed. 42 amp max rating.
Use for your street rod, truck, or muscle car!