Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Street Rod Drivetrain At Speedway Motors

Speedway Motors is the street rodder's source for street rod drivetrain components at everyday low prices! Select from a large assortment of slip yokes and ring & pinions to fit any need. Plus, you can find an assortment of gears to fit your application, all in one stop. Speedway also has a great selection of street rod rear end accessories, too – from gears, axles and slip yokes to bearings and brackets. We can even set you up with a complete Ford 9'' or a quick change rear end!

Featured Products
Winters Quick Change Gears, 10 Spline
From: $59.99
Product Rating: 4.67 Stars
Winters Quick Change Gears, 10 Spline
x
            
  • 8620 Steel
  • Heat Treated
  • CNC Machined
  • 10 spline
  • 1-1/4" Width

Winters Quick Change Gear Chart

Ford 9 Inch Posi Traction Third Member Assembly
Ford 9 Inch Posi Traction Third Member Assembly
x
            

Speedway Motors now offers you a 9" Ford street 3rd member for your street rod. We reclaim genuine Ford 9" housings, clean, inspect and install all new components. All bearings, seals, 1310 series yoke and ring & pinion are new!

These Ford 9" 3rd member assemblies feature new Pro Gears ring & pinion, choice of 3.50, 3.70, 3.89, 4.11 or 4.56, Currie 9-Plus limited slip differential, 28 or 31 spline. Shipped in handy plastic carrying case. Assembled by professionals.

 

Currie Differential Tech Bulletin (PDF)

 

910-48345 Instructions (PDF)

Speedway Four-Bar Rear Axle Brackets
Speedway Four-Bar Rear Axle Brackets
x
            

Exclusive sandwich-style brackets give greater bar support and incorporate a multi-position lower coil-over mount. Weld to 3" O.D. axle tubes only.

Lower coil-over shock mount stud not included.

Bare 56 Inch Centered 9 Inch Ford Housing w/ Axles
Bare 56 Inch Centered 9 Inch Ford Housing w/ Axles
x
            

Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 56" from hub-to-hub.   The pumpkin is centered in the housing, which puts the pinion offset 2-3/8" from center

Includes a set of Currie 31-spline heat-treated, forged alloy axle shafts. Wheel bolt patterns are dual drilled for 5 on 4 1/2" Ford and 5 on 4 3/4" Chevy, and an access hole is drilled. Axles come with a full installation package which includes one set of five 1/2"-20 Ford style wheel studs, one set of five 7/16"-20 Chevy style wheel studs, one set-20 tapered roller bearing with race, seal, & collar, and one heavy duty late model large bearing style retainer plate. Axle bearing does not come pressed onto the axle shaft, and wheel studs are not installed.

Third member sold separately.

"Street Rod, Driveline and Axles" Page 1 of 10

  • Dana Spicer 5-1350X Heavy Duty Cross U-Joint, 1350 Series, Non-Greaseable
    Dana Spicer 5-1350X Heavy Duty Cross U-Joint, 1350 Series, Non-Greaseable
    x
                

    Premium Spicer Life Series® u-joints excel in performance and life. The journal crosses are cold-formed from high quality steel for maximum strength. Non-Greasable u-joints have Ample grease reservoirs in each trunion to assure effective lubrication and are pre-filled with high quality synthetic lithium grease providing superior friction reduction and higher temperature resistance. Spicer Life Series® u-joints use Spicer's highest quality, triple-lip seal along with an external seal guard to resist the harshest conditions. So when you replace your car or truck universal joints with genuine Spicer technology, you can rest assured that you are helping to ensure the maximum life for your vehicle.

    Non-Greasable u-joints are stronger than greaseable units since they don't have any grease passages in them.

    • Heavy Duty U-joint
    • 1350 Series
    • 3.625 x 1.188
    • Non-Greaseable cross shaft


  • Dana Spicer 5-3615X U-Joint w/Coated Caps for Alum Driveshaft, 1350 Series
    Dana Spicer 5-3615X U-Joint w/Coated Caps for Alum Driveshaft, 1350 Series
    x
                

    Premium Spicer Life Series® u-joints excel in performance and life. The journal crosses are cold-formed from high quality steel for maximum strength. Non-Greasable u-joints have Ample grease reservoirs in each trunion to assure effective lubrication and are pre-filled with high quality synthetic lithium grease providing superior friction reduction and higher temperature resistance. Spicer Life Series® u-joints use Spicer's highest quality, triple-lip seal along with an external seal guard to resist the harshest conditions. So when you replace your car or truck universal joints with genuine Spicer technology, you can rest assured that you are helping to ensure the maximum life for your vehicle.

    Non-Greasable u-joints are stronger than greaseable units since they don't have any grease passages in them.

    • Coated Caps
    • 1350 Series
    • 3.625 x 1.188 
    • For use with Aluminum drive shafts
    • Non-Greaseable cross shaft


  • Bearing & Seal Kit for Brake Kit 910-31955
    Bearing & Seal Kit for Brake Kit 910-31955
    x
                Bearing & seal kit for GM Metric calipers & Mustang II rotors to 1949-54 Chevy spindle brake kit part 910-31955  &  910-31956. 

    Kit Includes:

    • Seals
    • Tapered inner bearing
    • Tapered outer bearing cones
    • Tapered outer bearing cups
  • New 9 Inch Ford Iron Carrier Housing w/3.062 Inch Caps
    New 9 Inch Ford Iron Carrier Housing w/3.062 Inch Caps
    x
                

    If you have built anything that has serious horsepower you know the weak link can be the stock Ford 9" carrier. The pinion area tends to be weak and if you throw enough power at it, it will break. That won't happen with this brand new housing. 

    This new cast iron housing is built to take street/strip abuse without the fear of breaking. Case has forged caps and extra beef where it's needed. Most stock differentials use the 3.062" o.d. bearings # TLM603049 w/ 1.781" i/d. You should also add a new heavy duty cast iron pinion support while you're at it. 

    • Forged Steel Caps
    • 1/2" Allen head grade 8 bolts
    • Heavy Duty Housing - 36 lbs.
    • Good for 1100 plus horsepower 
  • Halibrand V8 Quick Change Spacer Kit, 3 Pack
    Halibrand V8 Quick Change Spacer Kit, 3 Pack
    x
                We found a limited supply of these rare Halibrand V8 quick change parts. 

    Click to See Application Chart (Link)

  • Bare 60 Inch Centered 9 Inch Ford Housing
    Bare 60 Inch Centered 9 Inch Ford Housing
    x
                

    Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 60" from hub-to-hub. You will need one 28-3/8" long axle and one 30-5/8" long axle.   Includes 8 T-bolts for the axle bearing retainer plates and 10 studs for the 3rd member.

    Third member sold separately.

     

  • Spicer U-Joint, Chevy 1310 to Ford 1330
    Spicer U-Joint, Chevy 1310 to Ford 1330
    x
                
    • 3.219"x1.062" by 3.625"x1.062"
    • Series: 1310/30
    • Greasable
  • Bearing-Seal Kit for Two Mustang II Brake Rotors
    Bearing-Seal Kit for Two Mustang II Brake Rotors
    x
                

    This bearing and seal kit includes two inner wheel bearings, two outer wheel bearings and two inner grease seals. This kit is enough for two brake rotors and is intended to be used with a new rotor installation as this kit does not include the bearing races or cups.

    If your project willl be making use of used rotors, you will require new bearing races or cups.  Therefore you will need to purchase the bearing and seal kit # 910-31052 suggested below in place of kit # 910-31000.

    Works with Mustang II/Pinto and Granada rotors using Mustang II/Pinto spindles only. It will not work for installing Mustang II/Pinto brake rotors on 1949-1954 Chevy spindles. Not for use with early Chevy spindle brake conversion kits.

    -Large Bearing-
    Thickness: .656"
    Upper OD: 1.900"
    Lower OD: 2.150"
    Bearing ID: 1.375"

    -Small Bearing-
    Thickness: .651"
    Upper OD: 1.380"
    Lower OD: 1.570"
    Bearing ID: 0.864"

    Never install new hubs with old bearings.

  • OTB Gear 6870 Finned Cover For Round Back 9 Inch Rearend, Polished
    OTB Gear 6870 Finned Cover For Round Back 9 Inch Rearend, Polished
    x
                The perfect cure for the boring pumpkin. The sturdy and popular Ford 9"  rearend needs a little work to look stylish... at least thats what we  thought. This new cover is cast in A356 aircraft grade alloy and  available in a highly polished finish. No hardware is  needed to attach - we provide a generous supply of high temperature  adhesive (600 degree).
    • Excellent compliment to the new & improved Speedway 9" housing (910-46100)
    • Will fit most factory 9" Ford rear axle housings that have a bulge on the back of the housing for the ring gear, such as our axle # 910-46100 and other similar rear housings
    • No hardware is needed to attach
    • Generous supply of high temperature adhesive (600 degree) included
    • Can be powder coated after assembly
    • Will not fit Currie except, CE2000N made prior to September 2009
    • Will not fit axle housing used in Speedway #s 910-45100 and 715-700
    • Catalog correction, # 338 p# 61 shows the incorrect style of housing that this cover fits

    Instructions (PDF)

     

  • 9 Inch Ford Viton Pinion Seal
    9 Inch Ford Viton Pinion Seal
    x
                

    These Viton 9" Ford rear axle pinion seals are good to over 400° F. Stock rubber seal starts to deteriorate at about 250° F.

  • Dana Spicer 5-3614X U-Joint w/Coated Caps for Alum Driveshaft, 1330 Series
    Dana Spicer 5-3614X U-Joint w/Coated Caps for Alum Driveshaft, 1330 Series
    x
                

    Premium Spicer Life Series® u-joints excel in performance and life. The journal crosses are cold-formed from high quality steel for maximum strength. Non-Greasable u-joints have Ample grease reservoirs in each trunion to assure effective lubrication and are pre-filled with high quality synthetic lithium grease providing superior friction reduction and higher temperature resistance. Spicer Life Series® u-joints use Spicer's highest quality, triple-lip seal along with an external seal guard to resist the harshest conditions. So when you replace your car or truck universal joints with genuine Spicer technology, you can rest assured that you are helping to ensure the maximum life for your vehicle.

    Non-Greasable u-joints are stronger than greaseable units since they don't have any grease passages in them.

    • Coated Caps
    • 1330 Series
    • 3.625 x 1.062 
    • For use with Aluminum drive shafts
    • Non-Greaseable cross shaft


  • GM 10 Bolt Ring and Pinion Instal Kit, 8.5 R&P, 30 Spline
    GM 10 Bolt Ring and Pinion Instal Kit, 8.5 R&P, 30 Spline
    x
                Everything you need for a complete ring and pinion installation job. 

    Kit Includes:

    • cover gasket
    • crush sleeve
    • marking compound and brush
    • pinion and carrier bearings
    • pinion nut and washer
    • pinion seal
    • thread locking compound
    • sealer

    Note: Pinion-depth shims are not included. 

  • Fast Shafts BBSK-10 Billet U-Bolt Strap Kit, 1-1/16 Inch
    Fast Shafts BBSK-10 Billet U-Bolt Strap Kit, 1-1/16 Inch
    x
                

    NEVER OVERTIGHTEN U-BOLTS AGAIN !! 

    These universal billet strap kits fit 1310 U-Joint, Steel Girdle, Ford 9 inch.  They include case hardened bolts, nuts, flat and lock washers.

    • Billet strap kit
    • Fit 1310 U-Joint, Steel Girdle, Ford 9 inch
    • Include case hardened bolts, nuts, flat and lock washers
  • 9 Inch Ford Ring & Pinion, 4.56 Gear Ratio
    $159.99
    $169.99
    Product Rating: 4.00 Stars
    9 Inch Ford Ring & Pinion, 4.56 Gear Ratio
    x
                This product offers exceptional strength and service life at a great price! We offer a huge selection of ratios for your 9" Ford axle. 

    Other ratios from 4.78 thru 7.33 available in our Lightened Gear series. (Part numbers 91919-478, 91919-525, 91919-614, 91919-666, 91919-683, 91919-700, 91919-716, 91919-733).

    Note:  Circle track racing applications require a minimum of 4 qts. of rear end lube.  Using less than this amount will lead to immediate pinion bearing failure.

    Instructions (PDF)

  • 9 Inch Ford Ring & Pinion, 6.33 Gear Ratio
    $159.99
    $169.99
    9 Inch Ford Ring & Pinion, 6.33 Gear Ratio
    x
                This product offers exceptional strength and service life at a great price! We offer a huge selection of ratios for your 9" Ford axle. 

    Other ratios from 4.78 thru 7.33 available in our Lightened Gear series. (Part numbers 91919-478, 91919-525, 91919-614, 91919-666, 91919-683, 91919-700, 91919-716, 91919-733).

    Note:  Circle track racing applications require a minimum of 4 qts. of rear end lube.  Using less than this amount will lead to immediate pinion bearing failure.

    Instructions (PDF)

  • Ford 8 Inch Ring and Pinion Gears
    Ford 8 Inch Ring and Pinion Gears
    x
                "Pro" brand gears offer excellent quality at a great price!  We offer a terrific selection of ratios for your 8" Ford rear axle.
            
  • Currie 9+-98129 9 Inch Ford Cut-To-Fit 31 Spline Axle, 29 Inch
    Currie 9+-98129 9 Inch Ford Cut-To-Fit 31 Spline Axle, 29 Inch
    x
                Please view the product's page for more information
            
  • Ford C4 Transmission Drive Shaft Slip Yoke
    Ford C4 Transmission Drive Shaft Slip Yoke
    x
                

    This Ford C-4 driveshaft slip yoke measures 6.5" from the center of the U-joint cup to the front end of the yoke. Fits transmissions with 28 spline tailshafts. Accepts 1310 style U-joints (popular Chevy) with 1-1/16" cups and a spread of 3-7/32".

     

    Note: Due to the length of the yoke, it will fit C4 transmissions ONLY, and is not recommended for use on an AOD transmission. The expressed measurement or length of the slip yoke is taken from the center of the u-joint to tip, not overall.

  • Long Rear Axle Bracket
    $12.99
    Product Rating: 5.00 Stars
    Long Rear Axle Bracket
    x
                

    "Long" rear axle bracket for use with custom radius rod rear suspensions. 

    • Fits 3" diameter rear axle tube
    • 3/8" thick steel
    • 3/8" diameter holes
  • 9 Inch Ford Ring & Pinion, 5.14 Gear Ratio
    $159.99
    $169.99
    9 Inch Ford Ring & Pinion, 5.14 Gear Ratio
    x
                This product offers exceptional strength and service life at a great price! We offer a huge selection of ratios for your 9" Ford axle. 

    Other ratios from 4.78 thru 7.33 available in our Lightened Gear series. (Part numbers 91919-478, 91919-525, 91919-614, 91919-666, 91919-683, 91919-700, 91919-716, 91919-733).

    Note:  Circle track racing applications require a minimum of 4 qts. of rear end lube.  Using less than this amount will lead to immediate pinion bearing failure.

    Instructions (PDF)

  • 9 Inch Ford Ring & Pinion, 4.86 Gear Ratio
    $159.99
    $169.99
    9 Inch Ford Ring & Pinion, 4.86 Gear Ratio
    x
                This product offers exceptional strength and service life at a great price! We offer a huge selection of ratios for your 9" Ford axle. 

    Other ratios from 4.78 thru 7.33 available in our Lightened Gear series. (Part numbers 91919-478, 91919-525, 91919-614, 91919-666, 91919-683, 91919-700, 91919-716, 91919-733).

    Note:  Circle track racing applications require a minimum of 4 qts. of rear end lube.  Using less than this amount will lead to immediate pinion bearing failure.

    Instructions (PDF)

  • Housing Studs, 9 Inch Carrier
    Housing Studs, 9 Inch Carrier
    x
                Housing studs and ring gear bolts complete the package for your racing or street use 9" Ford axle. 

    Side bell thru bolts torque to 40-45 lbs.

  • 9 Inch Ford Ring & Pinion, 3.50 Gear Ratio
    9 Inch Ford Ring & Pinion, 3.50 Gear Ratio
    x
                This product offers exceptional strength and service life at a great price! We offer a huge selection of ratios for your 9" Ford axle. 

    Other ratios from 4.78 thru 7.33 available in our Lightened Gear series. (Part numbers 91919-478, 91919-525, 91919-614, 91919-666, 91919-683, 91919-700, 91919-716, 91919-733).

    Note:  Circle track racing applications require a minimum of 4 qts. of rear end lube.  Using less than this amount will lead to immediate pinion bearing failure.

    Instructions (PDF)

  • New Ford 9 Inch Aluminum Carrier Housing w/3.062 Inch Caps
    New Ford 9 Inch Aluminum Carrier Housing w/3.062 Inch Caps
    x
                

    This brand new carrier housing is built to take street/strip abuse without the fear of breaking. Our aluminum housing has forged caps and extra beef where it's needed. Most stock differentials use the 3.062" o.d. bearings # TLM603049 w/ 1.781" i/d.

    The aluminum case will save you 20 lbs. over the cast iron version. You should also add a new heavy duty aluminum pinion support while you're at it. 

    Carrier caps torque to 95 ft lbs.

  • Currie 9+-98126 9 Inch Ford Cut-To-Fit 31 Spline Axle, 26 Inch
    Currie 9+-98126 9 Inch Ford Cut-To-Fit 31 Spline Axle, 26 Inch
    x
                Please view the product's page for more information
            
  • Bearing & Seal Kit - 11 Inch Brakes to Mustang II Spindle
    Bearing & Seal Kit - 11 Inch Brakes to Mustang II Spindle
    x
                Bearing & seal kit for GM 11" rotor/Mustang II spindle brake kit (910-31944)

    Kit Includes:

    • Seals
    • Tapered inner bearing cones
    • Tapered inner bearing cups
    • Tapered outer bearing cones
    • Tapered outer bearing cups
  • Dana Spicer 15-153X Standard Greaseable Cross U-Joint, Chevy 1310 Series
    Dana Spicer 15-153X Standard Greaseable Cross U-Joint, Chevy 1310 Series
    x
                

    Dana OEM quality service replacement U-joints feature journal crosses that are manufactured from high-quality alloy forgings and heat treated for maximum life. The bearing cups are case hardened for strength and durability. The seals are made from nitrile rubber for optimum grease retention and contaminant exclusion. All of this is why we can say that genuine Spicer parts meet the rigorous Dana standards that have made it the global leader in automotive u-joint technology.

    SVL U-Joints are designed and tested to deliver reliable performance and value. When it comes to repairing or maintaining your vehicles, you can rest assured knowing all SVL products are engineered to meet the unique needs of the aftermarket and are backed by Dana Spicer.

    • Standard Cross U-joint
    • 1310 Series
    • 3.219 x 1.062 x 3.219 x 1.062
    • Greaseable w/zerk

     

  • 1928-48 Ford Quick Change Look Rear End Cover, Polished
    1928-48 Ford Quick Change Look Rear End Cover, Polished
    x
                

    The great look of a quick change rearend at a fraction of the price! Contoured to fit an early Ford "banjo" axle housing.

    916-47902 Instructions (PDF)

  • 9 Inch Ford Teflon Low-Drag Pinion Seal
    9 Inch Ford Teflon Low-Drag Pinion Seal
    x
                

    These Teflon 9" Ford rear axle pinion seals are good to over 400° F. Stock rubber seal starts to deteriorate at about 250° F.

  • Ford 9 Inch Shim Kit
    $29.99
    Ford 9 Inch Shim Kit
    x
                Kit Contains: nine pinion retainer shims consisting of one each .005", .006", .0075", .0082", two .004", and three .0105"; twelve pinion pre-load shims consisting of one each .005", .006", .0075", .0082", .009", .020", .030", two .050", and three .010"; one pinion spacer .375" thick; and one 3/4"-20 Ford pinion nut.
            
  • Low Rear Axle Bracket 5 3/4 Inch
    Low Rear Axle Bracket 5 3/4 Inch
    x
                All brackets are for 3" rear axle application.

    Low Rear Axle Bracket
    Mount radius rods lower than rear axle. 3/8" steel. 5-3/4" long. 3/8" holes.
  • 9 Inch Ford Housing Cover
    $14.99
    9 Inch Ford Housing Cover
    x
                Aluminum cover to keep 9" housing clean when you have your third member out.
            
  • 1935-48 Ford/Mercury High Torque Ring and Pinion Gear Set, 6.17 Gear
    1935-48 Ford/Mercury High Torque Ring and Pinion Gear Set, 6.17 Gear
    x
                These fit 1935-1948 passenger cars or 1935-1941 Ford 1/2 ton pick-ups (no 3/4 ton or larger). All gear sets are direct replacements for stock, non-quickchange rear axles. 6-spline input. 

    Installation Instructions  (PDF)

  • Winters Performance SR2550 SR2980 56 Inch V8 Quickchange, Plain
    Winters Performance SR2550 SR2980 56 Inch V8 Quickchange, Plain
    x
                

    It's been a long time since you could buy a 100% brand new V-8 quick change with the features this one showcases. Each of these assemblies includes new axles with 5 on 4-1/2" and 5 on 4-3/4" bolt patterns, 3.78:1 ring & pinion, Wedgelock differential, 1310 series yoke, and plain steel axle tubes. Accepts our part #91712 6-spline quick change gears.

    56" wide hub-to-hub. Uses the big Ford bearing (3.150") (Big Ford / New Style ) and has a 2-1/2" axle offset.

    THIS ITEM SHIPS TRUCK FREIGHT

  • Pinion Nut for 9 Inch Ford
    $4.99
    Product Rating: 5.00 Stars
    Pinion Nut for 9 Inch Ford
    x
                Thread pitch on this pinion nut is 3/4"-20. Fits 8" and 9" Ford rear axles.
            
  • New Ford 9 Inch Aluminum Carrier Housing w/3.25 Inch Caps
    New Ford 9 Inch Aluminum Carrier Housing w/3.25 Inch Caps
    x
                

    This brand new carrier housing is built to take street/strip abuse without the fear of breaking. Our aluminum housing has forged caps and extra beef where it's needed. Most stock differentials use the 3.062" o.d. bearings # TLM603049 w/ 1.781" i/d.

    The aluminum case will save you 20 lbs. over the cast iron version. You should also add a new heavy duty aluminum pinion support while you're at it. 

    Carrier caps torque to 95 ft lbs.

Goto Previous PagePrevious Page
1 2 3 4 5 ... 10