Speedway Motors is the street rodder's source for body parts, gauges, and interior accessories! Find all the essential fiberglass body components, gauge sets by Stewart Warner and Auto Meter, and hot rod bomber seats, in our online catalog. While you are there, check out our full line of script emblems, rear view mirrors, windshields, fiberglass hoods and grilles. Complete your hot rod with sound proof insulation from Dynalite and Hushmat. Don't forget about Speedway's hot rod bomber seats for your traditional street rod, too!
Linear actuators are gear-driven drive motors that extend a shaft with 110 lbs. of force. Our 12V actuators are a universal design for custom installation and operation in countless applications. With built-in limit switches, ACME dive system, and a IP 63 dust and water resistant rating, they are ideal for automotive applications (trunk, hood, doors, etc.) as well as electric wing sliders for Mini Sprints.
This linear actuator has a potentiometer and can be used with our controller # 910-64295. Available in 4", 6" or 8" strokes.
- Load Capacity - 110 pounds
- Static Load - 550 pounds
- Speed at Max Load - 0.50 in/sec
- Reccomended Fuse - 10 Amp
- IP Grade - IP 63-total dust protection, water resistant
- Pin Holes: 5/16"
- Retracted Length: 246 mm (9.69")
- Shaft Diameter: 20 mm (.787")
- Size: 10-1/4" x 1-1/2" x 3"
- Weighs approx. 2-3 lbs
Wiring Schematic (GIF)
You don't take chances when driving your family car. Why take chances when you're in your hot rod? Our D.O.T. approved seat belts are available in six popular colors. Painted push button buckles with standard, non-retracting belt. Lap belts adjustable from 60" to 74".
Has the mounting tabs sewn into place on the end of the belt. This arrangement makes positioning of the mounting holes in the car more important. If the installer wants the buckle near the wearer's hip, one side of the belt must be attached to the vehicle at a very specific location. Only half of the belt can be adjusted for length and thus position.
- Standard adjustable lap type
- Chrome lift latch
- Painted push buckles in red, black, maroon, grey, dark blue, or tan
- Lap belts adjustable from 60" to 74"
- Includes mounting hardware (2 bolts, 2 nuts, 2 washers)
Auto Meter Arctic White Series gauge kits are the hottest thing going. These feature a domed glass lens. The programmable electric speedometer allows you to compensate for tire size and gear ratio with a push of a button.
Set includes all senders. Speedometer sender fits GM and Chrysler transmissions. If using a 1957-Up Ford transmission, you will need to purchase an additional speedo sender, part # 182-5292 (at right).
- 3-1/8" Electric speedometer
- 2-1/16" Electric oil pressure, water temp, fuel, voltmeter gauges
Everybody loves our Bomber seats, but some wanted them with lightening holes. Just like the original, this one is hand made from .090" aluminum with a hand-formed bead. Measures 16" wide and 21" tall. Needs no upholstery. Weighs only 5.76 lbs!
Mounting brackets sold separately.
"Street Rod, Body" Page 1 of 25
$29.99More InfoSill Weather Whisker Stripx
After putting in new glass and window felt run channels, you don't want to reuse your old whisker that's on your garnish moldings, so here's a way to prevent scratching up that new glass. We now offer a 48" long, 9/16" tall whisker strip. Only offered in black.
$59.99More Info1928-31 Model A Front Crossmemberx
These replacement 1928-31 Model 'A' Ford front crossmembers lower a Model A chassis 2" below a stock crossmember. Replaces a cracked original or use it to start your reproduction frame off right. Made of heavy, 7-gauge steel with clearance for 1-3/4" cross spring. Welds to frame boxing plates of original or repro chassis.
$3.99More InfoUniversal Expanding Body Mountsx
If you are building a lightweight car like a "T" or an "A", mounting the body may present a problem. These neat expanding rubber universal body mounts allow you to drill a 3/4" hole in the top of the frame, insert a 3/8" coarse bolt, tighten, then the body is mounted.
Not recommended for cars newer than 1934.
$219.99More InfoPercy's Speedglass Window Material, 1/8 Inch Thickx
This amazing material from Percy's is just the ticket for windshields, side and rear windows. Not to be confused with the more economical plexi-glass, this material allows anyone to cut to fit with common hand tools, but its special coating is scratch and chemical resistant.
This surface hardened plastic is similar to Lexan, but can be cleaned like normal glass without scratching. You can even use windshield wipers on it and clean it with standard glass cleaners.
- 50% - 75% lighter than glass (depending on thickness)
- 1/2 the weight per equal thickness of glass
- Extremely shatterproof
- Excellent optical clarity
- Coated on both sides with a very scratch resistant coating
- Highly scratch and chemical resistant
- High resistance to pitting or sand blast effect
- Can be cleaned with standard glass cleaner, no extra polishes or cleaners needed
- Excellent water shedding capabilities
Technical Info (PDF)
SpeedGlass Instructions (PDF)
$9.99More InfoRubber GM Transmission Cushionx
OEM-style rubber transmission cushion for many '58-'82 GM transmissions including TH350 auto, Muncie, Saginaw, and others.
- Meets or exceeds OEM specifications
- Rubber formulation provides abrasion resistance and aging stability
- Tough, hardened steel plate & inserts
- Chemlock® bonding agent ensures superior rubber-to-metal bond
$4.99More Info1932 Ford Interior Door Escutcheonx
These are used on both the door handles and window crank handles.
- Polished stainless steel
- Inside handle escutcheons for 1932 passenger cars
- Sold Each
$11.99More InfoUniversal Aluminum Hingex
This universal aluminum piano hinge has a variety of uses on anything from race cars to T-buckets. Cut to fit.
1-1/2" wide with 3/4" of flat each side of pin. Includes two 36" length hinges.
$19.99More InfoNo Club Lone Wolf Car Club Plaquex
Complete the nostalgic look to your rod with this "Lone Wolf" plaque. Constructed of cast aluminum alloy that will not rust. Recessed background is finished in gloss black. No holes for mounting or hanging
$49.99More Info1932 Ford Stainless Steel Grille/Hood Trimx
This 1932 Ford stainless grille trim is made of polished stainless steel. It is the trim molding piece that goes between the grille and hood. This is the grille trim for a stock 32 ford grille shell. No other dimensions are available.
- 1932 Ford
- Polished stainless steel
- Fits between grille and hood
$159.99More InfoSpeedway 5 Gauge Setx
- Stainless steel bezel
- Backlit white face
- 3-3/8” Mechanical Speedometer
- 2-1/16” gauges
- 3-3/8” Mechanical Speedometer
- Mechanical oil pressure gauge and line kit
- Mechanical water temp gauge
- Fuel gauge and sender
From: $29.99More InfoLexan Wind Wingsx
16" x 6". Choose from two colors of wind wing, smoke or clear. Wing wings sold in pairs.
$24.99More Info1932 Ford Cowl Vent Handlex
This chrome cowl vent handle is for a 1932 Ford and is made of solid brass. Plated with chrome. These handles open and close the vent atop the firewall to let air in.
- Fits 1932 Ford
- Made of solid brass
- Plated with chrome
- With mounting nut and washer
$149.99More InfoBase Door Panel Kitx
Design your own custom door panel with Hagan panel components. This kit comes with 4 black panel boards that are 39" x 32" which include 50 inline panel clips and a How-To video. Base boards are made of dense 1/8" water-resistant cardboard.
$14.99More Info1932 Ford V8 Headlight Bar Emblem, Chromex
These reproduction V-8 headlight bar emblems come with a retaining screw to easily mount. They feature a beautiful chrome finish and are the perfect finishing touch for your 1932 Ford.
- Chrome finish
- 1932 Ford headlight bar emblem
- Mounts with included retaining screw
$49.99More InfoDoor Propsx
This door prop kit fits between your striker bolt and bear jaw latch to hold the door open at car shows or for maintenance and cleaning.
17" long (where they snap onto the door latch pins).
$19.99More InfoExtension For Peep Mirrorx
You want peep mirrors, but they are too short? With this 1-1/2" longer extension, that problem has gone away. Chrome plated to match the peep mirror and machined to fit at both ends.
Mirror not included.
$1,699.99More InfoPast Tech 1932 Ford DuVall Windshield Framex
The famous DuVall windshield is most unique windshield frame on the market today. The DuVall name is trademarked by Speedway Motors, so you know you are getting the real thing! Frame is constructed of solid, cast brass which can be polished, painted, or plated. A classic finishing touch to any 1932 Ford street rod.
Includes 5 ft. of black piping which mounts between the body and the winshield frame. Glass not included.
555-32600 Instructions (PDF)
$59.99More Info1932 Ford Roadster Inside Door Handle Assemblyx
These inside door handle kits are designed for 1932 Ford Roadsters. They feature a beautifully chromed finish and are a complete set for 2 doors.
- 1932 Ford Roadsters
- Chromed finish
- Complete set for 2 doors
$14.99More InfoLinear Actuator Aluminum Mounting Bracket, 1-1/2 x 1-1/2 Inchx
These billet aluminum mounting brackets are for our Linear Actuator 910-64290. They are designed to mount your linear actuators to hoods, trunks, etc. on either flat or angled surfaces. Solid aluminum construction provides the greatest strength possible while remaining a great looking piece. The brackets are a satin finish, but can be polished to a bright shine. Sold individually - you may need two mounts (one for each end of the actuator). Includes bracket and three securing screws.
- Billet aluminum
- Satin finish
- Mount linear actuators to hoods, trunks, etc.
- Mount to either flat or angled surfaces
- Sold individually - may need one mount for each end
- Works with Linear Actuator 910-64290
- Includes bracket and three securing screws
NOTE: The vendor no longer includes the mounting plate as pictured in previous catalogs.
$54.99More InfoTubular Transmission Mount with 2 Inch Dropx
Universal rear transmission mounts and heavy duty tube crossmember. Fit most GM, Ford, and Mopar manual and auto transmissions. Black powder coated finish. Crossmember must be welded directly into frame or to 3 hole mounting flanges for bolt-in application. Fits frames up to 38" wide.
Note: May require re-drilling of the mount holes when used with Ford C4/C6 trans cushion 910-18017.
$31.99$42.18More InfoDEi 050501 Floor and Tunnel Shield II, Heat and Sound Insulation, 2 Ft. x 21 Inchx
Designed to provide the best possible heat protection in areas where high temperatures are always present and problematic, Floor & Tunnel Shield II limits heat transfer on fire walls, transmission tunnels, floor boards, fuel cells and other areas where heat is an issue. Floor & Tunnel Shield II provides excellent light weight thermal protection, acts as a guard against track and road debris, and provides sound deadening as well.
Constructed with an embossed 10 mil aluminum face bonded to 1/8” composite glass-fiber core and backed with a high temp super strong pressure sensitive backing, Floor & Tunnel Shield II withstands up to 1750°F of direct continuous heat. The adhesive side holds past 450°F. Its improved multifaceted modern aluminum surface offers improved reflectivity and rigidity and allows for ease of installation. At only 3/16” thick, this product can be shaped and trimmed for a custom fit and is ideal for minimal clearance areas.
With a unique and patented finely woven glass-fiber backing, Floor & Tunnel Shield II is the easiest, most cost effective way to control thermal transfer while protecting expensive components and vehicle occupants from extreme heat situations and sound.
Floor & Tunnel Shield II can be used on any number of surfaces including, metal, aluminum, carbon fiber, plastic, and more. Multiple uses include: fire walls, under hoods, transmission tunnels, fl
$249.99More Info1932 Ford Grille Insert, Rodders Stylex
This 1932 Ford grille insert is made from beautifully polished stainless steel. "Rodder style" inserts do not have a crank hole. This measures approx. 27-3/8" tall and 17" wide. The grille is retained in the shell with screws going horizontal into the shell through the shell flange.
- Polished stainless steel
- Rodder style
- Does not feature crank hole
- 27-3/8" tall
- 17" wide
$49.99More InfoAuto Meter 3357 Transmission Temperature Gaugex
$7.99More InfoSteel Hood Pin Kit with Q-Clipsx
Hood pin kit contains two 1/2" chrome plated steel studs, two steel scuff plates, four nuts, and two flip-over Q-clip pins.
Threaded Windshield Stud, 1928-36 Ford, 3/8 Inch X 3/8 Inch NF X 2 Inchx
These threaded windshield studs feature a stop and include one stud and one cone nut. They are zinc plated for longevity. Fits 1928-31 Model A and 1932-36 Ford.
- Steel material
- (1) stud, (1) cone nut
- Sold each
Not included in our windshield kits.
From: $29.99More InfoLicense Plate Bracket, 2 Inch Tube Clampx
License plate mounting brackets attach to tube axles, spreader bars, etc. with a 2" O.D. This license tag bracket is available in plain or polished aluminum finishes.
Macs Antique Parts A41563S 30-31 Ford Model A Plain Square Step Platex
Cast aluminum step plate for 1930-31 Ford Model A. Square plate includes a built-in 5/16" stud to mount the plate (with nut and washer). Square plate has a smooth plain cast zinc finish.
$39.99More InfoAdjustable Seat Riserx
- Cadmium plated steel
- Sold in pairs
- Three mounting hole options to adjust height
$24.99More InfoStewart Warner 82310 Deluxe Ammeter Gauge, 2-1/16 Inch, 30-0-30 Ampsx
Stewart Warner Deluxe 2-1⁄16" diameter ammeter gauges feature a black face, white letters and chrome bezel. A 12 volt light is included.
$159.99More Info1942-48 Ford Dash Trim, Passenger Car, 3-Piece Chromex
These reproduction dash trim panels are an exact shape as the original and come in a 3-piece set. They feature a beautiful chrome plated finish.
- 1942-48 Ford passenger cars
- Exact shape as original
- Chrome finish
- 3-piece set
- 44-1/8" wide and 8-1/8" tall in the center
$199.99More Info1928-1929 Steel Side Splash Aprons without Humpx
These 1928-1929 Model A steel side splash aprons are exact and now available without the hump at the rear. Approximate length, 68".
$44.99More InfoSpare Tire Mount Mirrorx
Mounts on the side spare tire. 4" diameter, beveled edge mirror, adjustable 1" wide leather strap. Strap mounting length is 16.5" at shortest point and 20.5" at longest.
Only available in brown.
$11.99More InfoAuto Meter 2268 LS Series Oil Pressure Sender Adapterx
This LS Series oil pressure sender fitting allows your aftermarket 1/8" NPT oil pressure sending unit to be installed in place of the OEM oil pressure sender.
When installing aftermarket gauges, the OEM oil pressure sender is not required by the PCM and may be replaced by the aftermarket sender of your choice.
$6.99More Info1933-1940 Ford Oval Head Bumper Boltsx
These replacement oval head bumper bolts feature a stainless steel cover. They fit 1933-40 Fords and many others.
- Replacement oval head bumper bolt
- Stainless steel cover
- Fits 1933-40 Fords and many others
- Includes nut and lockwasher
$24.99More InfoGlass Run Channelx
This is a highly flexible U-shaped channel comes in an 8-foot-long x 5/8" wide coil with sides that are 9/16" tall. You will need one coil of window felt per door.
$11.99More InfoHood Saver Protective Clear Hood and Body Tape, 12 Ft. Rollx
Hood Saver is the world's finest transparent protective tape. This multi-purpose, waterproof super clear tape protects painted body parts and chrome from rock chips, tar and bugs. Hood Saver tape is easy to apply and remove. Provides an invisible protective film that is safe for all painted surfaces.
Comes in a 12 ft long roll that is 5" wide.
$14.99More Info4 Inch Peep Mirrorx
Our 4" diameter peep mirror clamps to the top edge of the door. Fits over a door edge that is app. 1/8" thick or thinner. Fits right or left side (reversible). A popular and universal mirror at a low cost. Sold each.
$9.99More InfoIdidit 2503000040 Universal Billet Aluminum Knob, 3/16 Inch Borex
Universal billet aluminum switch knobs work great as a headlight switch knob, dash knob, door knobs, lock knob, wiper knob, or a radio knob. These 3/16" versions are retained with a set screw.