Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products

Banner

Speedway Motors has the oval track racing parts you need to take the checkered flag! Whether you race on dirt or asphalt with a stock car or an IMCA modified, Speedway is your racing equipment headquarters. Be a winner with oval track racing parts from Speedway Motors - America's Racing Super Market®!

Featured Products
Winters Quick Change Gears, 10 Spline
From: $59.99
Product Rating: 5.00 Stars
Winters Quick Change Gears, 10 Spline
x
            
  • 8620 Steel
  • Heat Treated
  • CNC Machined
  • 10 spline
  • 1-1/4" Width

Winters Quick Change Gear Chart

Bearing-Seal Kit for Two Mustang II Brake Rotors
Bearing-Seal Kit for Two Mustang II Brake Rotors
x
            

This bearing and seal kit includes two inner wheel bearings, two outer wheel bearings and two inner grease seals. This kit is enough for two brake rotors and is intended to be used with a new rotor installation as this kit does not include the bearing races or cups.

If your project willl be making use of used rotors, you will require new bearing races or cups.  Therefore you will need to purchase the bearing and seal kit # 910-31052 suggested below in place of kit # 910-31000.

Works with Mustang II/Pinto and Granada rotors using Mustang II/Pinto spindles only. It will not work for installing Mustang II/Pinto brake rotors on 1949-1954 Chevy spindles. Not for use with early Chevy spindle brake conversion kits.

-Large Bearing-
Thickness: .656"
Upper OD: 1.900"
Lower OD: 2.150"
Bearing ID: 1.375"

-Small Bearing-
Thickness: .651"
Upper OD: 1.380"
Lower OD: 1.570"
Bearing ID: 0.864"

Never install new hubs with old bearings.

Winters Grand National Rear Ends
Winters Grand National Rear Ends
x
            Winters full floating Ford 9 inch Grand National rearend features lite weight steel hubs with brake rotor mounts. This Grand National rear end assembly comes complete with a new housing, two hubs, two brake rotors, two solid 31 spline axles, two drive flanges, ten lug nuts, rotor and drive flange bolts along with all the needed bearings and seals. 

Now available in either a 5 x 5" or 5 x 4-3/4" bolt pattern and three different widths:

  • 58" centered
  • 60" centered
  • 62" with a 1/2" offset.

 

1978-Up GM Metric Brake Calipers, IMCA Approved
1978-Up GM Metric Brake Calipers, IMCA Approved
x
            

These stock replacement single piston Metric calipers were standard equipment on 1978-88 GM mid-size cars (Cutlass, Grand Prix, Regals, Monte Carlo, etc.). They feature a 2.38" single piston, shielded bottom inlet, and will save 3-1/2 lbs. per side compared to mid-size 1969-1977 caliper.

 

  • IMCA approved
  • No core charge required
  • 7/16"-20 inlet
  • Can be used with brake hoses from Pre-1978 GM intermediate cars
  • Brake pads & bolts sold separately

 

Note: Does NOT include brake pads or slider bolts and bushings.

Speedway Reduction Pulley Combo for Small Block Chevy Short Pump
Speedway Reduction Pulley Combo for Small Block Chevy Short Pump
x
            

Kit includes a cast aluminum double groove cast aluminum water pump pulley, crank pulley, and a matched pair of heavy duty belts. Slows water pump speed by 20% for increased horsepower.

  • Upper Pulley Grooves:  Two
  • Lower Pulley Grooves:  Two 
  • Upper Pulley Diameter:  6-5/8" O.D.
  • Lower Pulley Diameter:  5-7/16" O.D.
  • Upper Pulley Snout Hole:  5/8" O.D. (can be drilled out to 3/4")

Fits Small Block Chevy V8 with '55-'68 short-style water pump with 5/8" shaft.

Note: The lower crank pulleys in our combo kits are manufactured thicker than normal stock pulleys.  This requires longer 3/8" bolts to be purchased separately.  Allen head type bolts recommended. 

Get the correct pulleys for your application by learning which water pump you have as explained in our tech article. SBC - Short vs Long Water Pump.

 

Longacre 65130 Black Door Bar Padding
Longacre 65130 Black Door Bar Padding
x
            

Add another element of safety to your roll cage. This fire-resistant door bar padding will help protect you if you take a shot to the driver's door. Easy to attach using molded-in straps.

  • Height: 16-5/8"
  • Length: 39-3/8"
  • Thickness: 1"
  • Protect your left elbow, arm, hand and wrist
  • Made from fire resistant padding similar to our High Density roll bar padding but slightly softer
  • Saves you tons of time - no need to cut and fit several separate pieces
  • Mounts quickly with adjustable molded-in straps
  • Sharp looking too with a clean appearance
Speedway Double Pass Aluminum Radiator, Chevy
Speedway Double Pass Aluminum Radiator, Chevy
x
            

Leave it to Speedway Motors to offer you a professional quality aluminum racing radiator at an affordable price. This double pass radiator works well for oval track racing applications where maximum efficiency is needed. The double pass design offers a 5 to 20 degree coolant temperature drop versus a standard, single pass radiator with equal core size. 

This double pass radiator features 100% all-aluminum construction. The furnace-brazed core increases durability compared to other radiators with epoxy-glued or crimped-gasket sealing methods. Two rows of 1 inch aluminum tubes allows this radiator to out cool  a similarly sized radiator with five rows of copper tubes. A rugged billet aluminum filler neck with screw-in bleed is also included.

This radiator is designed for Chevy applications with both water necks on the passenger side. The upper inlet measures 1-1/2 inches outside diameter and the lower outlet measures 1-3/4 inches outside diameter. The radiator is available in 22", 24", 26", 28", or 31" widths, including the end tanks. All sizes are 19 inches tall.

  • All-aluminum, furnace-brazed construction
  • No epoxy, glue or crimped in gaskets
  • Maximum amount of fins per inch allows greater heat transfer
  • Two rows of 1" aluminum tubes (out cools five rows of copper)
  • Billet aluminum filler neck
  • Available in 22", 24", 26", 28", or 31" width (measurements include tanks)

Learn more about how radiators work and selecting the proper radiator for your vehicle by reading our tech article. Radiator Cooling Performance.

Bell Supreme SA10 Racing Helmet
Bell Supreme SA10 Racing Helmet
x
            

Speedway Motors has teamed up with Bell USA to bring a Bell quality racing helmet to the sportsman or entry level racer.  We are proud to introduce a Speedway Motors exclusive: the “Supreme” helmet by Bell.  The Snell SA2010 rated Supreme helmet is designed to offer value and quality at an affordable price.

  • Snell SA2010 Racing Helmet
  • Sportsman or Entry Level Racer
  • Unmatched Value and Quality 

Tear off posts are included. Available in white, black or flat black.

Bell Helmet Sizing Chart (PDF)

Proper Fitting Guidelines (PDF)

 

"Oval Track" Page 1 of 25

  • Longacre 65130 Black Door Bar Padding
    Longacre 65130 Black Door Bar Padding
    x
                

    Add another element of safety to your roll cage. This fire-resistant door bar padding will help protect you if you take a shot to the driver's door. Easy to attach using molded-in straps.

    • Height: 16-5/8"
    • Length: 39-3/8"
    • Thickness: 1"
    • Protect your left elbow, arm, hand and wrist
    • Made from fire resistant padding similar to our High Density roll bar padding but slightly softer
    • Saves you tons of time - no need to cut and fit several separate pieces
    • Mounts quickly with adjustable molded-in straps
    • Sharp looking too with a clean appearance
  • Low Profile Grease Zerks
    $7.99
    Product Rating: 5.00 Stars
    Low Profile Grease Zerks
    x
                

    Great for spindles and other areas needing added clearance. Stainless steel construction with 5/16" hex head with 1/4 - 28 UNF thread.

    Includes 5 zerks per bag. MUST be used with grease needle # 910-1187.

  • 1955-1985 Small Block Chevy Stock Car Racing Clutch Kit
    1955-1985 Small Block Chevy Stock Car Racing Clutch Kit
    x
                This stock car racing clutch package lets you order all the parts you need with one easy part number. 1-1/8"-10 spline disc. 

    Included:
    • Bellhousing
    • 153 Tooth Lightweight Flywheel
    • ARP Flywheel Bolts
    • 10-1/2" Lightweight Pressure Plate
    • ARP Pressure Plate Bolts
    • Solid Hub Organic Clutch Disc
    • Hydraulic Release Bearing
    • Extended Pilot Bearing
    • Clutch Alignment Tool
  • Head Stud Remover and Tap Alignment
    Head Stud Remover and Tap Alignment
    x
                

    Allows removal of stock press-in studs and aligns the tap (7/16"-14) to simplify the installation of screw in rocker studs.

    For S/B Chevy V8 engines.

  • Magnetic Drain Plug
    $3.99
    Product Rating: 5.00 Stars
    Magnetic Drain Plug
    x
                

    Metal debris can wreak havoc on an engine. Install this plug in your oil pan to catch any metal filings before they get sucked into the oil pump and cause real damage!

    Will fit any oil pan with 1/2-20 threads.

  • Inverted Flare Thread Nuts for 3/16 Inch Tubing, 3/8-24
    Inverted Flare Thread Nuts for 3/16 Inch Tubing, 3/8-24
    x
                

    Steel 3/8"-24 IFM thread nuts for 3/16" brake line when double flared to 45°.

  • Speedway Ultrasonic Multi-Purpose Parts Cleaner
    Speedway Ultrasonic Multi-Purpose Parts Cleaner
    x
                

    This ultrasonic parts cleaner is ideal for cleaning carburetor parts, fuel injector parts, small items such as wheel bearings, and other delicate components. Features a 6.6" x 5.4" x 2.5" tank size and includes a cleaning basket. 

    • Works on 110 volt power
    • Adjustable timer in 5 min. increments up to 30 mins.
    • Works well with a white vinegar solution
  • Speedway Reduction Pulley Combo for Small Block Chevy Short Pump
    Speedway Reduction Pulley Combo for Small Block Chevy Short Pump
    x
                Please view the product's page for more information
            
  • Axle Housing Inner Seal, 9 Inch Ford Grand National/Quick Change Rearends
    Axle Housing Inner Seal, 9 Inch Ford Grand National/Quick Change Rearends
    x
                

    High cornering forces can force the gear lube out of the center section and down the axle tube leaving the ring and pinion high and dry! This billet aluminum seal has three O-rings that seal it to the axle tube and two bonded, heavy duty, neoprene inner seals designed to compensate for any amount of axle shaft runout. Keeps gear oil in the center section. These seals will take up to an 1.5” diameter axle.

    • Anodized billet aluminum
    • A must for cambered rear ends
    • For 9" Ford Grand National and Quick Change type housings
    • For up to 1.5” diameter axle
    • Keeps gear oil in the center section
    • Outside Diameter: 2.56"
    • Overall Length: 1.50"
    • This seal will fit our steel wide 5 axle
    • Choose housing tube I.D. size needed:
      • 2.500" - Gold
      • 2.562" - Blue
      • 2.625" - Red
      • 2.750" - Silver

    919-0951 Instructions (PDF)

  • MD3 LH Fender New Style
    From: $54.99
    MD3 LH Fender New Style
    x
                The Maximum Downforce nose has 2" of taper built in to allow for chassis set-up and prevent the nose from plowing. Choose White, Red, Chevron Blue, Yellow and Black. Choose Monte Carlo, GTO, Impala SS, Camry, Fusion of Charger graphics. Graphics sold separately.
            
  • Rocker Arm Balls for 7/16 Inch Stud
    Rocker Arm Balls for 7/16 Inch Stud
    x
                Replacement rocker arm pivot balls with oil slots. Comes in a set of 16 for use with 7/16" rocker arm studs.
            
  • Magnetic Engine Heater
    $49.99
    Magnetic Engine Heater
    x
                This 200 Watt engine oil/block heater features a magnetic base. 110 volt, 5 foot cord.
            
  • Wheel Rim Repair Wrench
    $20.99
    Product Rating: 4.50 Stars
    Wheel Rim Repair Wrench
    x
                

    This handy rim repair wrench allows you to repair your steel racing wheels for less than the cost of a new wheel.

    • Special jaw radius fits perfectly over the lip of any wheel 
    • Straightens edges of the wheel & rolls the curl back into the wheel
    • Will not crease or crack the wheel
    • Heavy duty steel construction
  • Heads for Grooving Iron
    $12.99
    Heads for Grooving Iron
    x
                

    Grooving Iron heads for grooving irons listed below.

    • 445-250 - Tru-Hot Grooving Iron
    • 445-251 - Ideal Grooving Iron
    • 910-82065 - Econ-o-siper

    Grooving Iron Replacement Heads and Blades Application Chart

  • Axle Spring Perch, Plain Forged Steel
    Axle Spring Perch, Plain Forged Steel
    x
                Works with 1928-34 Ford front ends with 1-3/4" wide cross spring. Extra long for lower shock mounts. Includes nylock nut.
    • 2-1/2" from top of threads to mid shoulder
    • 2-7/8" from top of threads to top of shoulder
    • Thread length is 1-7/8"
    • Distance from the top of the shoulder to the bottom of the threads is 4-3/4"

    Leaf Spring Measuring Guide (Link)

  • Titan Tools 51503 Mini Tubing Bender
    $14.99
    $19.97
    Product Rating: 5.00 Stars
    Titan Tools 51503 Mini Tubing Bender
    x
                
    • Bends 1/8, 3/16, and 1/4" tubing up to 90 degrees
    • Use with Brass, Copper, Steel, or Aluminum
    • Compact for limited accessibility applications
  • TCI Automotive 950631 Max Shift Circle Track Racing ATF, Quart
    TCI Automotive 950631 Max Shift Circle Track Racing ATF, Quart
    x
                

    TCI® Max Shift™ Circle Track automatic transmission fluid has been tested and proven to enhance drivetrain performance and durability, and it can operate at far greater temperatures than both petroleum-based transmission fluids and synthetic formulas.

    This formula offers several unique benefits to circle track racers, including anti-foaming agents that reduce pump cavitation for more consistent line pressures. Max Shift™ Circle Track also maintains an exceptionally high viscosity level at high temperatures, which increases the life of not only the fluid, but of the clutches and bands, as well. This makes the formula ideal for resistance against high temperature drivetrain wear, as well as fluid breakdown that is common in most high performance circle track racing applications. In addition, applications using a torque converter see minimized slippage, which translates into quicker acceleration on the straightaways.

    Note: Not for street use - this is a racing formulation only.

  • Tire Stagger Tape, 10 Feet
    $5.99
    Tire Stagger Tape, 10 Feet
    x
                Stagger tape features thumb locking feature. 10' long, 1/4" wide steel tape. Use to measure tire circumference. 
            
  • High Pressure Radiator Cap, 22-24 Lbs
    High Pressure Radiator Cap, 22-24 Lbs
    x
                

    A must have when racing! High pressure cap for radiators raises boiling point of water.

    Learn more about cooling systems, how to choose the proper pressure cap, and how they work by reading our tech article. Cooling System Principles

  • Straight Aluminum Hose Connectors, 6 Inch
    Straight Aluminum Hose Connectors, 6 Inch
    x
                

    These 6" long aluminum radiator/coolant hose connectors have a bead at each end to keep the hose from coming off under pressure. Can be cut to length.

    Choose hose diameter (O.D.) needed.

  • Tru-Shot Rechargeable Liquid Sprayer, Black
    Tru-Shot Rechargeable Liquid Sprayer, Black
    x
                

    Great for use with Mudd-Off, Mud-X, Brake Kleen, penetrating oils or solvent based products. Not for all water based products.

    • One quart capacity
    • Powder coated steel can
    • Adjustable nozzle
    • Works with 80-100 psi
  • 25 Lb. Lead Ballast
    $59.99
    25 Lb. Lead Ballast
    x
                Lead ballasts allow you to put the weight where you want it. Economical and hard-to-find. Perfect for 305 sprint car racing. 
            
  • Synthetic Chamois
    $4.99
    $9.95
    Synthetic Chamois
    x
                

    Use on cars, furniture, glass, etc. Can be used wet or dry and washed up to 500 times. Big 26" by 19".

     

     

  • Metal Pegboard Tool Organizer, 32 x 32 Inch Wall Control Storage System
    Metal Pegboard Tool Organizer, 32 x 32 Inch Wall Control Storage System
    x
                Durable, all-steel construction will not warp, fray  or crack. Attractive, scratch  resistant,  baked-on powder coat finish wipes clean for long-lasting  beauty for any  shop or work area. Installation is easy and absolutely no  framework is  required. 
    • 32" tall x 32" wide x 3/4" deep
    • Pack of two
    • Durable and versatile
    • 20 gauge steel with a baked-on rust and scratch resistant finish
    • Slotted to accept Wall Control accessories
    • Holes accept conventional 1/4" peg hooks
    • Choose from blue, grey, red, white, or galvanized steel
  • Dura-Bond FKC-1HP Small Block Chevy Engine Finishing Hardware
    Dura-Bond FKC-1HP Small Block Chevy Engine Finishing Hardware
    x
                

    Kit Includes:

    • (4) Head Dowels
    • (2) Timing Cover Dowles
    • (3) Cam Bolts
    • (1) Cam Lock Plate
    • (2) Oil Filter Adaptor Bolts
    • (1) Long Woodruff Key
    • (2) Short Woodruff Keys
    • (2) Transmission Dowels
  • Longacre Accuset II Scale Kit
    $999.99
    Product Rating: 3.00 Stars
    Longacre Accuset II Scale Kit
    x
                
    • Push one button for all 4 wheel weights plus cross weight
    • Push a second button for all partial %
    • Baseline memory recall
    • Heavy duty red HiFlex cables with billet AN connectors
    • 4 LMF™ swirl finished 15" x 15" low profile pads
    • 1500 lb. per pad capacity, 6000 lb. total
    • 2-year limited warranty
    • Includes FREE scale pad box

    Instructions (PDF)

  • Bearing-Seal Kit for Two Mustang II Brake Rotors
    Bearing-Seal Kit for Two Mustang II Brake Rotors
    x
                

    This bearing and seal kit includes two inner wheel bearings, two outer wheel bearings and two inner grease seals. This kit is enough for two brake rotors and is intended to be used with a new rotor installation as this kit does not include the bearing races or cups.

    If your project willl be making use of used rotors, you will require new bearing races or cups.  Therefore you will need to purchase the bearing and seal kit # 910-31052 suggested below in place of kit # 910-31000.

    Works with Mustang II/Pinto and Granada rotors using Mustang II/Pinto spindles only. It will not work for installing Mustang II/Pinto brake rotors on 1949-1954 Chevy spindles. Not for use with early Chevy spindle brake conversion kits.

    -Large Bearing-
    Thickness: .656"
    Upper OD: 1.900"
    Lower OD: 2.150"
    Bearing ID: 1.375"

    -Small Bearing-
    Thickness: .651"
    Upper OD: 1.380"
    Lower OD: 1.570"
    Bearing ID: 0.864"

    Never install new hubs with old bearings.

  • Flathead Lifter Wrench
    $9.99
    Product Rating: 4.25 Stars
    Flathead Lifter Wrench
    x
                

    Use this handy wrench to set your flathead's adjustable lifters.  For use with our 450-F8502 lifters.

  • Speedway Vertical Steering Reservoir Tanks
    Speedway Vertical Steering Reservoir Tanks
    x
                Vertical mounted power steering reservoir tanks available in 1.5 lb. standard weight or 0.7 lb. lightweight.  The top return fitting is the industry standard AN 6 size. Available with AN 8 or AN 10 outlets. These tanks are NOT internally baffled.  

    Bracket sold separately. Bracket can be welded to the tank, strapped to the tank with hose clamps, or custom-mounted to suit your needs.

  • Power Steering/Coolant Tank Mount
    Power Steering/Coolant Tank Mount
    x
                

    Use this handy 3" tall aluminum bracket to mount your power steering reservoir tank or your coolant overflow expansion tank. Can be welded to the tank, strapped to the tank with hose clamps, or custom-mounted to suit your needs.

    Tank NOT included. 

  • ARP Fasteners 100-1110 5/16 Inch Head Header Bolts
    ARP Fasteners 100-1110 5/16 Inch Head Header Bolts
    x
                
    • Great for getting the proper torque in tight spaces
    • 3/8-16 x 1" threads
    • 5/16" hex head
    • Set of 16
  • Speed Fast Stainless Safety Wire, .032 Inch
    Speed Fast Stainless Safety Wire, .032 Inch
    x
                Speed Fast 304 stainless steel safety wire. Sold in one pound rolls and comes with a handy belt clip.
            
  • 9 Inch Ford Viton Pinion Seal
    9 Inch Ford Viton Pinion Seal
    x
                

    These Viton 9" Ford rear axle pinion seals are good to over 400° F. Stock rubber seal starts to deteriorate at about 250° F.

  • Winters Performance 5419 Powerglide Drive Flange Sleeve
    Winters Performance 5419 Powerglide Drive Flange Sleeve
    x
                

    Powerglide drive flange sleeve for steel crank drive flange. 

     

  • Monte Carlo SS Stock Car Nose
    $99.99
    $114.99
    Product Rating: 4.50 Stars
    Monte Carlo SS Stock Car Nose
    x
                

    Two-piece nose for your Monte Carlo SS.  Just the ticket for IMCA type stock cars.  Nose pieces available in black, white, yellow, red, Chevron (dark) blue, or orange. Sold in sets.

    • Length:  66"
    • Width:  10"
    • Height:  22"
  • Performance Tool W54220 Grease Suction Gun
    Performance Tool W54220 Grease Suction Gun
    x
                Great for filling or emptying rear ends and trannys.  You shouldn't be without one!
            
  • Grand National Rear Hub Bolts, Pair
    Grand National Rear Hub Bolts, Pair
    x
                

    Pair of Grand National rear end drive flange screws.

    • flathead Allen screws
    • 5/16"-18 x 3/4"
    • 1/2" thread length
    • black oxide coated steel
  • Universal Aluminum Hinge
    $11.99
    Product Rating: 5.00 Stars
    Universal Aluminum Hinge
    x
                

    This universal aluminum piano hinge has a variety of uses on anything from race cars to T-buckets. Cut to fit.

    1-1/2" wide with 3/4" of flat each side of pin. Includes two 36" length hinges.

  • Longacre 50883 Tire Marking Pen
    Longacre 50883 Tire Marking Pen
    x
                

    Writes directly on the tire's surface to easily remember tire sizes or other measurements.

    • Makes a finer line, easy to read
    • Mark tire sizes, pressures, etc.
    • Silver marking won't come off from heat
  • Winters Performance 7271 Grand National Snout Seal
    Winters Performance 7271 Grand National Snout Seal
    x
                2-1/2” double lipped seal with spring seal retainer. Seals around the GN axle.
            
Goto Previous PagePrevious Page
1 2 3 4 5 ... 25