Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Pony Stock At Speedway Motors

Speedway Motors has everything you need for your Mini Stock or Pony Stock race car! We stock all the best race parts for the Ford 2.3 four cylinder, from forged pistons and rods to racing carburetors and oil pans. Add even more power to your Ford 2300 with a billet distributor and header. Check out our assortment of Mustang II front suspension components, Pinto leaf springs and Ford 8'' rearend parts, too!

"Oval Track, Pony Stock" Page 1 of 25

  • 2.3 Ford Round Tooth Timing Set
    2.3 Ford Round Tooth Timing Set
    x
                

    If you are making serious power out of your 2.3 Ford engine, it will only be a matter of time before you strip the square teeth off a timing belt.

    This round-tooth timing kit includes a lightweight aluminum adjustable upper sprocket, lower sprocket, auxillary shaft sprocket and round-tooth belt.

  • Speedway 9 Inch Ford Chromoly Cross Pin
    Speedway 9 Inch Ford Chromoly Cross Pin
    x
                

    Our 3/4" cross pin for the 8" & 9" Ford axle is machined from chromoly steel and will stand up to lots of racing abuse.

  • IMCA Approved Pinto-Mustang II Spindles
    IMCA Approved Pinto-Mustang II Spindles
    x
                Brand NEW, heat-treated forged Mustang II steel spindle that retains the exact OEM geometry of the 74-78 Mustang II or 74-80 Pinto spindle. This is the ONLY aftermarket spindle allowed by IMCA. Work great with our 10" HD Hybrid Rotors as well as with stock rotors, bearings, calipers, ect. Stock 7 5/8" height.  Easy to install.
            
  • 2.3L Ford Billet Timing Belt Tensioner
    2.3L Ford Billet Timing Belt Tensioner
    x
                

    Designed for all out racing conditions, these 2.3L Ford timing belt tensioners feature a machined stainless steel back plate, billet aluminum pulley and 13k RPM double roller bearings. The spring pin is an exclusive shoulder pin design, not a cheap spring pin like the competition. Eliminates costly and severe valvetrain damage caused by stock 2-piece stamped wheel.

  • Drive Shaft Safety Loop
    $29.99
    Product Rating: 4.50 Stars
    Drive Shaft Safety Loop
    x
                This driveshaft safety loop holds the drive shaft in place in case of universal joint failure. Made from 2" x 1⁄4" hot rolled steel with grade 5 bolts. Bolt-on installation.
            
  • Cloyes Gear B014 1974-91 2.3L Ford Timing Belt
    Cloyes Gear B014 1974-91 2.3L Ford Timing Belt
    x
                

    Meets or exceeds OEM performance requirements. Cloyes utilizes the latest in design and material technology, ensuring quiet and maintenance-free experience.Timing belts made of wear resistant fabric, resisting oil and engine heat. High tensile strength cord construction minimizes stretch.

    • Pitch:  3/8"
    • Teeth:  129
    • Width:  0.878"
  • MSD 6425 6AL Digital Ignition Control Box
    MSD 6425 6AL Digital Ignition Control Box
    x
                

    The MSD Digital 6AL features a higher output with 530 primary volts and 135mJ of spark energy. Efficient components use less current to produce more power. Set an rpm limit on the MSD 6AL rev limiter with two rotary dials. Has the same bolt pattern as the original 6AL, but with a lower profile housing. Built-in LED for system checks. All wires exit the same side through a locked, sealed connector. Compatible with 4, 6 and 8-cylinder engines.

    547-6425 Instructions (PDF) 

    MSD Tech Bulletin

    Learn more about the benefits and features of the MSD 6AL Digital Ignition Control Box by reading StangTV's tech article.  MSD's Newest 6AL Takes Conventional Ignitions into the Digital Age.

    Learn more about determining the proper MSD ignition control box for your application by reading our tech article. The Differences Between 6 Series MSD Ignition Control Units.

  • Premium 9 Inch Ford Mini Spool, 31 Spline
    Premium 9 Inch Ford Mini Spool, 31 Spline
    x
                

    Our forged 8620 steel mini spools are designed to replace the spider gears inside the stock differential carrier. This premium mini spool features a larger diameter for maximum strength. It works great for most dirt applications and some asphalt.

    • For Ford 8 or 9" rear axles.
    • Will NOT work on posi carrier.
    • Use with 3/4" chromoly cross pin (listed) # 655-7520.
  • ARP Fasteners 200-2902 Chevy Flexplate Bolts
    ARP Fasteners 200-2902 Chevy Flexplate Bolts
    x
                

    Flexplate bolts play an important role in the performance and safety of race cars and street machines alike. That’s why the fastener experts at ARP develop special bolts that are far superior to OEM hardware. Forged from aerospace alloy and heat-treated prior to thread rolling and machining.

    Fits Chevrolet 90° V6 & 265-454 Chevy V8 with 2-Pc rear seal. Set of 6 bolts.

    • Exclusive, flat, 12-point head design
    • Larger than stock shank diameter for increased strength and improved flexplate register
    • Originally developed for NASCAR Winston Cup competition
    • 200,000 psi rating
  • 2.3 Ford Forged Cam Followers
    $149.99
    2.3 Ford Forged Cam Followers
    x
                

    These steel Forged Ford 2.3 cam followers feature wear pads and stabilizer grooves for the mouse trap springs.  They come ready to install with assembly lube. Sold in sets of 8.

    • Wear pads
    • Stabilizer grooves for mouse trap springs
    • Kit complete with assembly lube
    • Sold in sets of 8
  • Clevite Engine Parts SH777S 77 Ford 2.3 Cam Bearings
    Clevite Engine Parts SH777S 77 Ford 2.3 Cam Bearings
    x
                Camshaft bearings for Ford 2.3L engines. Available in standard size only.
            
  • Timing Pointer for Esslinger 2.3 Ford Lower Pulley
    Timing Pointer for Esslinger 2.3 Ford Lower Pulley
    x
                

    These pulleys require relocating the timing pointer. This bolt-on timing pointer works well for this application.

  • ARP Fasteners 200-2802 Chevy Flywheel Bolts
    ARP Fasteners 200-2802 Chevy Flywheel Bolts
    x
                

    Flywheel bolts play an important role in the performance and safety of race cars and street machines alike. That’s why the fastener experts at ARP develop special bolts that are far superior to OEM hardware. Forged from aerospace alloy and heat-treated prior to thread rolling and machining.

    Fits Chevrolet 90° V6 & 265-454 Chevy V8 with 2-pc rear seal. Set of 6 bolts.

    • Exclusive, flat, 12-point head design
    • Larger than stock shank diameter for increased strength and improved flywheel register
    • Originally developed for NASCAR Winston Cup competition
    • Has a 200,000 psi rating
  • 2.3 Ford Mouse Springs
    $44.99
    2.3 Ford Mouse Springs
    x
                For 2.3 Ford adjustable valve train kits (91519815).
            
  • Ultra Light 2.3L Ford Square Tooth Adjustable Cam Sprocket
    Ultra Light 2.3L Ford Square Tooth Adjustable Cam Sprocket
    x
                

    Ultra lightweight adjustable cam gear for the Ford 2.3 mini stock engines. These adjustable gears eliminate the need for the large steel factory belt guide washer, as they are machined directly into these gears. Gears feature ARP nuts and bolts to eliminate stripping of the aluminum due to repeated use. These gears are designed using 3D modeling and FEA testing to provide the lightest Ford 2300 adjustable cam gear on the planet.

    • Easily tune your engine for different track conditions
    • Hard anodized aluminum construction
    • Adjust cam timing in less than one minute
    • Adjustable in 1 degree increments
    • Instructions on degreeing your cam included
    • 1/2 the weight of stock pulley
    • No need to loosen center bolt

     

     

  • ARP Fasteners 151-5402 2.3 Ford Main Stud Kit
    ARP Fasteners 151-5402 2.3 Ford Main Stud Kit
    x
                190,000 PSI studs will keep your motor together. These ARP fasteners are second to none. Don't have stock bolts let you down when you least expect it. 
            
  • Speedway 1968-89 Chrysler-Type Upper K772 Style Ball Joint
    Speedway 1968-89 Chrysler-Type Upper K772 Style Ball Joint
    x
                

    These Chrysler-type screw in ball joints fit a variety of race car and street car applications.See Application tab for complete list.

    Same as Moog K772.

  • Speedway Single-Layer Two-Piece Racing Suit Combos
    Speedway Single-Layer Two-Piece Racing Suit Combos
    x
                Please view the product's page for more information
            
  • Speedway Economy Single-Layer One-Piece Racing Suit Combos
    Speedway Economy Single-Layer One-Piece Racing Suit Combos
    x
                Please view the product's page for more information
            
  • Holley 0-4412CT Circle Track 500 CFM 2 Barrel Carburetor
    Holley 0-4412CT Circle Track 500 CFM 2 Barrel Carburetor
    x
                This 500cfm 4412CT Holly carb shares the hugely  successful features of the original 4412C but with a couple changes  aimed for circle track cars. The choke has been removed but the horn  remains and has been specially calibrated for circle track use. The  4412C Holley carb is easily the most winningest two barrel carburetor on the market  and comes out of the box ready to run. 

    Features:
    • Choke delete
    • Choke horn remains
    • 50cc accelerator pump
    • 1 timed (spark) port, 1 full vacuum, & 1 PCV port
    • The mandated carbs for many oval track racing sanctioning bodies
    • Calibrated specifically for circle track use
  • Premium 9 Inch Ford Mini Spool, 28 Spline
    Premium 9 Inch Ford Mini Spool, 28 Spline
    x
                

    Our forged, heat-treated 8620 steel mini spools are designed to replace the spider gears inside the stock differential carrier. This premium mini spool features a larger diameter for maximum strength. It works great for most dirt applications and some asphalt.

    For Ford 8 or 9" rear axles. Will NOT work on posi carrier. Use with 3/4" chromoly cross pin (listed).

  • Speedway Single-Layer One-Piece Racing Suit Combos
    Speedway Single-Layer One-Piece Racing Suit Combos
    x
                Save big with this great combo! 

    Kit includes:
    • Speedway FRC (fire retardant cotton) Driving Suit
      • SFI-1 Certified
      • One-piece
      • Sizes S-XXL
      • Available in Black, Blue, or Red
    • Speedway Single-layer Nomex Racing Gloves
      • SFI-1 Certified
      • Full leather palm, mitered finger design for a comfortable fit
      • Sizes S-XL
      • Available in Black, Blue, or Red
    • Speedway FRC Neck Brace
      • Fire retardant cotton cover and foam inner pad
      • Velcro closure for universal fit
      • SFI 3.3-1 Ceritified
      • Available in Red, Blue, Black, or Purple
    • Speedway High Top Driving Shoes
      • SFI 3.3/5 Certified
      • Soft, flexible, high grade split leather
      • Sizes from 7-14
      • Available in Black, Blue or Red 

    Note:  Helmet is shown for reference only and is not included as part of kit.

    Suit Sizing Chart (GIF)

    Glove Sizing Chart  (GIF)

  • Pro Shocks SS300 Pro Street Stock Shock, Pinto Front
    Pro Shocks SS300 Pro Street Stock Shock, Pinto Front
    x
                

    Pro street stock shocks are  non-adjustable. Designed to replace the stock shocks in the original mounting locations. They have extra heavy damping, designed for the punishment of Street Stock racing.

    For 1971-80 Pinto and 1974-78 Mustang II.

  • Speedway Bump Stop Dividers for 5/8 Inch Shaft
    Speedway Bump Stop Dividers for 5/8 Inch Shaft
    x
                These are a great tool for fine-tuning your bump  stop system. The steeper the dish, the less progressive the bump stop  will be. Best suited for use with multiple puck-style bump stops.
    • For shocks with 5/8" shaft diameters
    • Anodized aluminum
    • Available in 4 tapers:
      • 0 deg. - Black
      • 5 deg. - Blue
      • 10 deg. - Gold
      • 15 deg. - Red
  • Ford Mustang II-Pinto Caliper
    Ford Mustang II-Pinto Caliper
    x
                Remanufactured Mustang II/Pinto caliper with retaining clip hardware. 7/16"-24 inlet.

     

  • Single Sided Metric Lug Nut, 1 Inch Hex
    Single Sided Metric Lug Nut, 1 Inch Hex
    x
                Finally a metric lug nut that takes a 1" socket. Fits the popular 12mm x 1.5 studs and gives you the safety of a larger clamping area.

    Note: Lug nut shown here features a 90 degree included angle and should only be used with aftermarket circle track wheels. OEM wheels require a lug nut that uses a 60 degree included angle.
  • Pinto-Mustang II Spindle Nut & Washer Kit
    Pinto-Mustang II Spindle Nut & Washer Kit
    x
                Complete kit for 2 spindles; nuts, washers, cotter pins.  For 1974-80 Pinto, Bobcat and Mustang II. Thread size of nut: 13/16"-20
            
  • Ford 2.3 Billet Distributor
    $99.99
    Product Rating: 1.67 Stars
    Ford 2.3 Billet Distributor
    x
                Our billet aluminum distributor for 2300 or 2.3 Liter SOHC Ford 4 cylinder engines is far superior to stock units and give you a higher spark energy and more accurate timing.  

    Requires an ignition box, mechanical advance only.
  • Steve Smith Autosports S289 Book - Building the Mustang Mini Stock
    Steve Smith Autosports S289 Book - Building the Mustang Mini Stock
    x
                

    A step-by-step buildup of a Mustang Mini Stock project car. Provides detailed instruction on how to build you own race car.

    • Finding a suitable car
    • Stripping the car
    • Installing a roll cage
    • Working with a unibody chassis
    • Using a McPherson strut front suspension
    • Designing the front suspension geometry
    • Working with the stock 4-point rear suspension and coil springs
    • Complete race car fabrication and preparation
    • Complete chassis setup and alignment
    • Scaling the car and adjusting the weight
    • Chassis adjustments and troubleshooting
    • Ford 2300cc performance engine build-up
    • For dirt and paved tracks
  • Bassett Pony-Mini Stock 13 Inch Wheel - 13x7, 4 on 4 1/2, Black
    Bassett Pony-Mini Stock 13 Inch Wheel - 13x7, 4 on 4 1/2, Black
    x
                

    Pony/Mini Stock Bassett steel 13 inch racing wheels are the wheel of choice for Pony/Mini Stock and Legend cars. 4 on 4-1/2" bolt pattern. 2" and 3" backspacing. This 4 lug wheel is offered in black.

    • 13 Inch Wheel
    • 7 Inch Wide
    • 4 on 4-1/2 Inch Bolt Pattern
    • Black
    • Offered with 2" or 3" Backspace
    • For Pony Stock, Mini Stock, or Legend Cars 

    How to Measure Wheel Backspace

     How to Measure Bolt Circles

  • Speedway Single-Layer One-Piece Racing Suit Combos
    Speedway Single-Layer One-Piece Racing Suit Combos
    x
                Please view the product's page for more information
            
  • Aero 33-974035BLK 33 Series 13x7 Wheel, Lite, 4 on 4 BP, 3-1/2 BS
    Aero 33-974035BLK 33 Series 13x7 Wheel, Lite, 4 on 4 BP, 3-1/2 BS
    x
                

    Aero Race Wheels 33 Series steel wheels are designed for dirt oval track use only. The CNC roll-formed 33 Series wheels have very low run-out beadlocks, using 16 zinc plated flange bolts. They feature a 7-hole D-window center disc made of HSLA material and include a mudcover installation kit.  Mudcover tabs are incorporated into the inner ring to eliminate the need for welding.

    • Recommended for dirt use only
    • Designed for vehicles up to 2500 lbs.
    • Must use 1" O.D. lug nuts with 45 degree taper
    • Standard beadlock ring is yellow

    Note: The 4-on-4" bolt pattern will work on 4 on 100 mm if NOT using 5/8" studs.

    Learn more about determining the proper wheel offset, torque sequence, and bolt pattern for your application by reading our tech article, Racing Wheel Principles.

  • Aero 55-074230 55 Series 15x7 Wheel, 4-lug, 4 on 4-1/4 BP, 3 Inch BS
    Aero 55-074230 55 Series 15x7 Wheel, 4-lug, 4 on 4-1/4 BP, 3 Inch BS
    x
                

    Aero Race Wheels 55 Series steel wheels are designed for oval track use. The roll-formed 55 Series wheels have a 7-hole D-window center disc made of HSLA material for strength and durability.  They feature knife edged bead humps, maximum bead seats, and low run-out. 

    • Recommended for oval track use
    • Must use 1" O.D. lug nuts with 45 degree taper

    Learn more about determining the proper wheel offset, torque sequence, and bolt pattern for your application by reading our tech article, Racing Wheel Principles.

  • Aero 33-904240PIN 33 Series 13x10 Wheel Lite 4 on 4-1/4 BP 4 Inch BS
    Aero 33-904240PIN 33 Series 13x10 Wheel Lite 4 on 4-1/4 BP 4 Inch BS
    x
                

    Aero Race Wheels 33 Series steel wheels are designed for dirt oval track use only. The CNC roll-formed 33 Series wheels have very low run-out beadlocks, using 16 zinc plated flange bolts. They feature a 7-hole D-window center disc made of HSLA material and include a mudcover installation kit.  Mudcover tabs are incorporated into the inner ring to eliminate the need for welding.

    • Recommended for dirt use only
    • Designed for vehicles up to 2500 lbs.
    • Must use 1" O.D. lug nuts with 45 degree taper
    • Standard beadlock ring is yellow

    Learn more about determining the proper wheel offset, torque sequence, and bolt pattern for your application by reading our tech article, Racing Wheel Principles.

  • Aero 31-904030RED 31 Series 13x10 Wheel, Spun Lite, 4 on 4 BP, 3 BS
    Aero 31-904030RED 31 Series 13x10 Wheel, Spun Lite, 4 on 4 BP, 3 BS
    x
                

    Aero Race Wheels 31 Series steel wheels are designed for asphalt oval track use only. The CNC spun-formed 31 Series wheels have extremely low run-outs. They feature a 7-hole D-window center disc made of HSLA material with a new torque ring design.

    • Recommended use for asphalt only
    • Designed for vehicles up to 2500 lbs.
    • Must use 1" O.D. lug nuts with 45 degree taper
    • 31 Series DO NOT have safety bead humps

    Note: The 4-on-4" bolt pattern will work on 4 on 100 mm if NOT using 5/8" studs.

    Learn more about determining the proper wheel offset, torque sequence, and bolt pattern for your application by reading our tech article, Racing Wheel Principles.

  • Aero 33-984010BLU 33 Series 13x8 Wheel, Lite, 4 on 4 BP, 1 Inch BS
    Aero 33-984010BLU 33 Series 13x8 Wheel, Lite, 4 on 4 BP, 1 Inch BS
    x
                

    Aero Race Wheels 33 Series steel wheels are designed for dirt oval track use only. The CNC roll-formed 33 Series wheels have very low run-out beadlocks, using 16 zinc plated flange bolts. They feature a 7-hole D-window center disc made of HSLA material and include a mudcover installation kit.  Mudcover tabs are incorporated into the inner ring to eliminate the need for welding.

    • Recommended for dirt use only
    • Designed for vehicles up to 2500 lbs.
    • Must use 1" O.D. lug nuts with 45 degree taper
    • Standard beadlock ring is yellow

    Note: The 4-on-4" bolt pattern will work on 4 on 100 mm if NOT using 5/8" studs.

    Learn more about determining the proper wheel offset, torque sequence, and bolt pattern for your application by reading our tech article, Racing Wheel Principles.

Goto Previous PagePrevious Page
1 2 3 4 5 ... 25