Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Oval Track Fasteners & Hardware At Speedway Motors

Speedway Motors has the oval track racing parts you need to take the checkered flag! Whether you race on dirt or asphalt with a stock car or an IMCA modified, Speedway is your racing equipment headquarters. Be a winner with oval track racing parts from Speedway Motors - America's Racing Super Market!

Featured Products
Standard Clevis, 5/8 Inch RH, 3/8 Inch Slot, Plain
Standard Clevis, 5/8 Inch RH, 3/8 Inch Slot, Plain
x
            

A beautiful clevis ideal for your Hot Rods' suspension!

5/8" RH Thread, 3/8" Slot, 3/8" Hole, Plain
Tru Rivets, 3/16 Inch Large Head
From: $9.99
Product Rating: 4.50 Stars
Tru Rivets, 3/16 Inch Large Head
x
            Large head 3/16" aluminum pop rivets with steel shank. 1/4" to 3/8" grip range. Available in red, white, pepsi (light) blue, chevron blue, yellow, black, and orange. Box of 250.
        
Plain Steel Sleeves for 5/8 Inch Rod Ends
Plain Steel Sleeves for 5/8 Inch Rod Ends
x
            

If you are building a hot rod just a little bit different than the next guy, you will probably need a special length tie rod or drag link sleeve. We stock many common and uncommon lengths along with custom, made-to-order lengths. Measurements are in assembled eye-to-eye lengths.

To order:

  1. Use guide below to measure your finished length.
  2. The part number and length you order will be 3" longer than the sleeve you receive. (I.E., if you order a 48" part number, you will receive a 45" long sleeve.) This is the difference in length required to give you the correct finished center-to-center measurement.
  3. All sleeves will have internal RH thread in one end and LH thread in the other.

Measuring Guide for Tie Rod/Drag Link (GIF)

Large Head 3/16 Inch Exploding Rivets
Large Head 3/16 Inch Exploding Rivets
x
            

Ok, they don’t really explode, but the back side splits into folds so you don’t normally need to use a back-up washer with them. They work great where it’s hard to reach the back side. Choose small or large head and the color of your choice. Plain, Black, White, Red, Orange, Yellow, Pepsi (light) Blue or Chevron (dark) Blue.

  • Box of 250
  • Large head is 5/8 O.D.
  • Aluminum pop rivet with aluminum shank

Color Chart (GIF)

"Oval Track, Fasteners and Hardware" Page 1 of 10

  • Speed Fast Stainless Safety Wire, .032 Inch
    Speed Fast Stainless Safety Wire, .032 Inch
    x
                Speed Fast 304 stainless steel safety wire. Sold in one pound rolls and comes with a handy belt clip.
            
  • 3/16 Inch Back Up Washers
    $8.99
    3/16 Inch Back Up Washers
    x
                Use with our pop rivets for added strength. 3/16" aluminum. Box of 500. 
            
  • Rue Clip for Quick Release, 1/2 Inch
    Rue Clip for Quick Release, 1/2 Inch
    x
                Rue clip for a quick release. 1/2".
            
  • JAZ Products 720-000-01 Engine Stand Drip Tray
    JAZ Products 720-000-01 Engine Stand Drip Tray
    x
                
    • Helps keep your shop floor clean during engine disassembly
    • Designed to fit most three and four leg engine stands 
    • Made from durable black plastic for long service 
    • Cleans easily with soap and water or in a solvent tank 
    • Big enough to catch debris from a big block 
    • Small enough to stay out of your way
  • AFCO 50401 Ludwig Clamps, 4 Pack
    AFCO 50401 Ludwig Clamps, 4 Pack
    x
                
    • Secures hinged lids, panels, etc
    • Held in place by a single rivet
  • Tru Rivets, 3/16 Inch Large Head
    From: $9.99
    Product Rating: 4.50 Stars
    Tru Rivets, 3/16 Inch Large Head
    x
                Large head 3/16" aluminum pop rivets with steel shank. 1/4" to 3/8" grip range. Available in red, white, pepsi (light) blue, chevron blue, yellow, black, and orange. Box of 250.
            
  • 7/16 Inch to AN3 Banjo Fitting
    7/16 Inch to AN3 Banjo Fitting
    x
                7/16 Inch to AN3 Banjo Fitting
            
  • Plastic AN Cap and Plug Kit - 72 Pieces
    Plastic AN Cap and Plug Kit - 72 Pieces
    x
                

    If you don't have one of these kits, get one now. Includes six each cap and plug for AN 3, AN 4, AN 6, AN 8, AN 10 and AN 12.

  • Performance Tool 45214 125-Piece Assorted Rubber Grommet Kit
    Performance Tool 45214 125-Piece Assorted Rubber Grommet Kit
    x
                

    These rubber grommet assortment kits are the perfect solution for running wires through your firewall.  They are designed to keep wires or any other materials from rubbing on steel or aluminum and allow you to pass fuel line, cables, and wiring neatly through body panels without the risk of damage.

    Rubber Grommet Kit

    • 125 Piece Assortment
    • Clear plastic divider case
  • AN Fitting Plug Economy Pack
    $15.99
    AN Fitting Plug Economy Pack
    x
                

    These AN fitting plugs have always been hard-to-find items. Plugs are used when sealing spare race engines against dirt and water during transportation and storage. Each plug is reusable. Use on oil, fuel, or coolant lines.

    Economy packs contain one four pack each of -4 AN, -6 AN, -8 AN, -10 AN, and -12 AN size.

  • Winters Performance 7479 Grand National Hubcap O-Ring
    Winters Performance 7479 Grand National Hubcap O-Ring
    x
                
            
  • Split Wire Loom Conduit Tubing, 3/8 Inch Diameter, 12 Ft. Long
    Split Wire Loom Conduit Tubing, 3/8 Inch Diameter, 12 Ft. Long
    x
                

    This plastic split wire loom allows you to clean up that ugly wiring under the hood for a more professional look. This tubing will group and protect your wires from damage.  Simply lay out and insert wires, which will remain inside even with flex.  Choose from 5 colors to customize your engine bay: black, dark blue, purple, red, or yellow. 

    • 12 ft. long
    • 3/8" diameter
    • Plastic split conduit
    • More professional appearance
    • Groups and protects wires against damage 
    • Retains wires under flex and adjustment
    • Comes with zip-ties to secure wire loom
    • Choose: black, dark blue, purple, red, or yellow
  • 14 Gauge Primary Automotive Electrical Accessory Wire, 100 Foot Roll
    14 Gauge Primary Automotive Electrical Accessory Wire, 100 Foot Roll
    x
                

    Designed for interior, engine bay, and chassis wiring jobs, our accessory wire is high-quality automotive wire with a stranded-copper core.  It resists grease, oil, acids, and diesel fumes, and meets SAE automotive specs.  To give your wiring project a professional look, this top-notch wire is available in a variety of colors.

    14 Gauge Primary Automotive Wire

    • High temperature
    • 14 gauge
    • Multi-strand wire
    • 100 ft. roll
    • Choose from colors; black, blue, orange, purple, red and yellow.
  • 26 Compartment Organizer
    $8.99
    26 Compartment Organizer
    x
                
    • Plastic storage cas
    • 26 compartments with clear cover
  • Plain Steel Sleeves for 5/8 Inch Rod Ends
    Plain Steel Sleeves for 5/8 Inch Rod Ends
    x
                

    If you are building a hot rod just a little bit different than the next guy, you will probably need a special length tie rod or drag link sleeve. We stock many common and uncommon lengths along with custom, made-to-order lengths. Measurements are in assembled eye-to-eye lengths.

    To order:

    1. Use guide below to measure your finished length.
    2. The part number and length you order will be 3" longer than the sleeve you receive. (I.E., if you order a 48" part number, you will receive a 45" long sleeve.) This is the difference in length required to give you the correct finished center-to-center measurement.
    3. All sleeves will have internal RH thread in one end and LH thread in the other.

    Measuring Guide for Tie Rod/Drag Link (GIF)

  • Aluminum Flare Fitting Cap, Blue, -6 AN
    Aluminum Flare Fitting Cap, Blue, -6 AN
    x
                

    Aluminum caps to seal 37° flare AN male fittings. Blue anodized finish.

    Fitting Thread Application Chart (GIF)

  • Easy Release Snap Fasteners
    $3.99
    Product Rating: 5.00 Stars
    Easy Release Snap Fasteners
    x
                Perfect hold down for access doors and panels. Bag of four.  
            
  • Valve Cover Studs, Set of 8
    $7.99
    Product Rating: 5.00 Stars
    Valve Cover Studs, Set of 8
    x
                1/4"-20 thread, 1-1/2" long studs come with nylocks and washers. Set of 8 are included.
            
  • Steel Jam Nuts, 3/4 Inch-16 NF Fine Thread, Pack/6
    Steel Jam Nuts, 3/4 Inch-16 NF Fine Thread, Pack/6
    x
                

    If you've got spherical rod ends on your vehicle, you'll probably need jam nuts. You might also need them for tie-rod ends or other types of fittings and connectors. Our jam nuts are made from premium steel (zinc-coated for corrosion prevention), and they're available with either right hand or left hand threads.

    These steel fine thread jam nuts are for use with rod ends, heim joints, and clevis.

    • 3/4 Inch-16 NF Fine Thread
    • Sold in bags of six nuts.
    • Choose left or right thread.
  • Zip Tie Wraps, 14 Inches
    $8.99
    Product Rating: 5.00 Stars
    Zip Tie Wraps, 14 Inches
    x
                Zip ties available in black, blue, red, white, yellow, orange, or purple.  Package of 100.
            
  • Steel 1/2 Inch Quick Release Ball Lock Dowel Pin Fastener, 3-1/4 Inch Grip
    Steel 1/2 Inch Quick Release Ball Lock Dowel Pin Fastener, 3-1/4 Inch Grip
    x
                

    These quick-release push-button pins offer you the ultimate in quick-release fastening. They are made of high-grade steel and work great for any quick applications. Choose 3-1/4" grip. 1/2" diameter for coil-over shocks.

    Quick Release Ball Lock Dowel Pin Fastener
    • Overall length 4.740"
    • Overall diameter 1.380"
    • Shaft diameter 0.500" (1/2")
    • Steel
    • 3-1/4" grip length
  • Standard Clevis, 5/8 Inch RH, 3/8 Inch Slot, Plain
    Standard Clevis, 5/8 Inch RH, 3/8 Inch Slot, Plain
    x
                

    A beautiful clevis ideal for your Hot Rods' suspension!

    5/8" RH Thread, 3/8" Slot, 3/8" Hole, Plain
  • Steel Jam Nuts, 5/8 Inch-18 NF Fine Thread, Pack/6
    Steel Jam Nuts, 5/8 Inch-18 NF Fine Thread, Pack/6
    x
                

    If you've got spherical rod ends on your vehicle, you'll probably need jam nuts. You might also need them for tie-rod ends or other types of fittings and connectors. Our jam nuts are made from premium steel (zinc-coated for corrosion prevention), and they're available with either right hand or left hand threads.

    These steel fine thread jam nuts are for use with rod ends, heim joints, and clevis.

    • 5/8 Inch-18 NF Fine Thread
    • Sold in bags of six nuts.
    • Choose left or right thread.
  • Winters Performance 5010 Pro-Eliminator Rearend Thrustblock
    Winters Performance 5010 Pro-Eliminator Rearend Thrustblock
    x
                

    Pro-Eliminator and Winters Rearend Replacement Parts

    • Winters Thrustblock

    Speedway Motors has everyting you need to repair or upgrade your Winters quick change rearend. From center sections and gear sets to bearings, washers and O-Rings, we can help you get your rear back on the track!

    Winters Replacement Parts Figure (PDF)

    Pro Eliminator Rear End Diagram (GIF) 

  • Weld-In Weight Jack Nuts w/ Grease Zerk, Coarse Thread
    Weld-In Weight Jack Nuts w/ Grease Zerk, Coarse Thread
    x
                
    • Replacement nut for weight jack bolts
    • Available for 1" or 1-1/8" diameter coarse thread bolts
    • Includes grease zerk
  • Kinsler Fuel Injection 3117 Fuel Line Bypass Pill Holder O-Ring Kit
    Kinsler Fuel Injection 3117 Fuel Line Bypass Pill Holder O-Ring Kit
    x
                

    Replacement set of O-rings for Kinsler bypass pill holder 3112. Includes (1) small O-ring and (1) large O-ring. Compatible with both gas and methanol.

  • Quarter Turn Springs with Step, Pack/10
    Quarter Turn Springs with Step, Pack/10
    x
                

    Stepped quarter turn springs mount easily with pop rivets. The step is approximately 0.250". Overall height of spring is 0.400" to 0.425". Eye-to-eye measurement is 1-3/8".

    Measurement Guide (Link)

  • Tru-Lite Titanium Bolt, 5/16-18 Coarse Thread, 1 Inch Long, 1/2 Inch Hex Head
    Tru-Lite Titanium Bolt, 5/16-18 Coarse Thread, 1 Inch Long, 1/2 Inch Hex Head
    x
                

    These coarse thread Tru-Lite titanium bolts feature heat treated rolled threads. Titanium bolts have a greater tensile strength than Grade 8 bolts at half the weight. Made from 6AL/4V material which has 3 times the strength of aluminum and is 42% lighter than steel.

    • Coarse thread Titanium
    • Greater tensile strength than Grade 8 bolts
    • 3 times the strength of aluminum
    • 42% lighter than steel
    • 5/16"-18 x 1"
    • 1/2" Hex Head
    • Full Thread
  • OEM Style Ford Tapered Nuts for Front Spring Perch
    OEM Style Ford Tapered Nuts for Front Spring Perch
    x
                Axle perch nut for 1928-1948 Ford style front axle perches. 5/8"-18 tapered castle nut.
            
  • Swedged Aluminum Throttle Linkage Tubes, 3/16 Inch (10-32) Thread
    Swedged Aluminum Throttle Linkage Tubes, 3/16 Inch (10-32) Thread
    x
                

    This swedged throttle linkage tubing is tapped 3/16" (10-32) LH and RH thread. One end of the throttle rod will have left hand threads, and the other end will have right hand threads. Made of 5/16" x 0.049 round aluminum tubing.

    Note: When measuring for your tube length, you will want to allow 1.5" in length for the rod ends (3/4" of length for each end when calculating your eye-to-eye measurement. For instance, an eye-to-eye length of 11.5" would require a 10" swedged tube.

  • HDPE Sealing Washers for Bulkhead Fittings
    HDPE Sealing Washers for Bulkhead Fittings
    x
                

    Use these HDPE (High Density Polyethylene) washers to seal bulkhead fittings to fuel cells, oil tanks and other low pressure situations. Order by AN size needed.

    Fitting Thread Application Chart (GIF)

  • Split Wire Loom Conduit Tubing, 1/4 Inch Diameter, 20 Ft. Long
    Split Wire Loom Conduit Tubing, 1/4 Inch Diameter, 20 Ft. Long
    x
                

    This plastic split wire loom allows you to clean up that ugly wiring under the hood for a more professional look. This tubing will group and protect your wires from damage.  Simply lay out and insert wires, which will remain inside even with flex.  Choose from 5 colors to customize your engine bay: black, dark blue, purple, red, or yellow. 

    • 20 ft. long
    • 1/4" diameter
    • Plastic split conduit
    • More professional appearance
    • Groups and protects wires against damage 
    • Retains wires under flex and adjustment
    • Comes with zip-ties to secure wire loom
    • Choose: black, dark blue, purple, red, or yellow
Goto Previous PagePrevious Page
1 2 3 4 5 ... 10