Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Oval Track Electric Switches & Connectors At Speedway Motors

Find all your race car switch panels, warning lights and wiring accessories at Speedway Motors - America's Racing Super Market. Speedway Motors stocks many of the most dependable brands in the racing industry, including AFCO, Longacre and Painless Wiring. Shop now for same day shipping on these oval track racing electrical components!

Featured Products
Two Post Battery Disconnect Switch
Two Post Battery Disconnect Switch
SKU-91064500
x
            Remote battery disconnect switch for safety and theft protection. A battery kill switch is required for use with alternators by the NHRA. Battery shut off switch can be remote mounted or where specified for saftey and  convenience.
  • 180 amp continuous, 1000 amp instantaneous
  • Die cast lever
  • Fits panel through 3/16" thick

910-64500 Instructions (PDF)

Toggle Ignition On Switch
$9.99
Product Rating: 4.75 Stars
Toggle Ignition On Switch
SKU-91364380
x
            Toggle switch works great as a kill switch or with other auxiliary equipment. 25 amp SPST switch with rubber boot and on/off plate.
        
Universal Relay for Fan/Horn
$16.99
Product Rating: 5.00 Stars
Universal Relay for Fan/Horn
SKU-91064109
x
            

This heavy duty relay takes the heavy-amp load off the switch, thus preventing an overheated circuit and a possible wiring harness fire. Works well with electric fans and horn circuits too. 30 amp relay.

The wiring for the relay is as follows:

  • Short Red Wire (from relay post 87) = power lead to horn or fan
  • Long Red Wire (from relay post 30) = main power supply in
  • Short Black Wire (from relay post 85) = makes ground connection thru a temp sensitive switch or a grounding horn button
  • Long Gray Wire (from relay post 86) = connects to switched 12 volt power (like ignition switch) so horn or fan turns on/off with key

Includes relay, circuit breaker, wire, terminals and instructions.

Universal Fan Relay Installation Instructions (PDF)

Auto Meter 5289 GPS Sending Module-Universal for Electric Speedometers
Auto Meter 5289 GPS Sending Module-Universal for Electric Speedometers
SKU-1825289
x
            

This unit allows nearly any electric speedometer to use free GPS signals to drive the speedometer. No more cables, no more calibration drives. If you've got an Auto Meter electronic speedometer, it's a plug and play solution. Calibration on non-Auto Meter speedometers takes about 10 seconds and doesn't require driving. The Module uses the fastest possible GPS technology for truly seamless functionality.

  • Lightning fast 10Hz Signal
  • Separate paintable 1" square antenna with optional magnetic attachment capability
  • Waterproof antenna and module assembly (IP67 sealed)
  • Factory calibrated for 16,000 pulses per mile
  • One touch calibration
  • Compatible with Electronic Speedometers Only

"Oval Track, Electrical, Lighting and Body" Page 1 of 4

  • AFCO 85053B Starter Switch Panel with Lights, 4-1/8 x 5-7/8 Inch
    AFCO 85053B Starter Switch Panel with Lights, 4-1/8 x 5-7/8 Inch
    SKU-10685053B
    x
                

    AFCO starter switch panels are for standard ignitions.

    Wiring Instructions (PDF)

  • AFCO 85293 Warning Light, Oil Temp.
    AFCO 85293 Warning Light, Oil Temp.
    SKU-10685293
    x
                

    These lights allow the driver to maintain focus on the race.

    Wiring Instructions (PDF)

  • MSD 8183 2-Pin Deutsch Connector, 16 gauge
    New
    MSD 8183 2-Pin Deutsch Connector, 16 gauge
    SKU-5478183
    x
                There is absolutely no excuse for losing a race due to a poor wiring connection. MSDs Deutsch Connectors are sealed and lock together making them perfect for harsh racing applications. The compact housing of the connectors are molded from a durable plastic material that will not harden or crack. Each housing is indexed to prevent any chance of mismatching the ends plus they have a molded channel to secure another connector for a tidy appearance.The terminals grip to the wire with strong crimp tabs then lock into position inside the housing. The connections are protected with thick seals that will keep water, mud and debris away from the contacts. These terminals can handle more current than conventional connectors and do not require special tools. Supplied with terminals, seals and housings.

    Installation Instructions (PDF)

  • Painless Wiring 50302 6-Switch Fused Panel with Wiring and Hardware
    New
    Painless Wiring 50302 6-Switch Fused Panel with Wiring and Hardware
    SKU-91050302
    x
                

    This heavy duty lightweight switch panel from Painless Performance is designed to mount to a roll bar using standard metal hose clamps. All of the circuits are individually fused and are easily accessible for quick testing and replacement. This kit comes complete with 18 ft. of wire, using fully insulated terminals. Made in the USA!

    Installation Instructions (PDF) 

    The Kit Controls:

    • Start
    • Ignition
    • Fuel pump
    • Electric fan/water pump
    • Two accessories

     

     

  • MSD 8961 MSD High Current Relay, SPST
    $26.99
    $29.99
    New
    MSD 8961 MSD High Current Relay, SPST
    SKU-5478961
    x
                MSDs High Current Relays are what you need to activate accessories that draw high current. These Relays are very reliable due to the fully automated manufacturing process and sophisticated coil winding procedure. The SPST High Current Relay is rated at 30 amps with an input voltage of 12 volts DC. The relay is ideal for use with the MSD RPM Activated Switch when 12 volts are responsible for activating a high current device such as a nitrous solenoid.The DPST relay is also rated at 30 amps with a 12 volt input voltage. This Relay is the best choice when 12 volts are required to activate multiple high current devices at the same time such as multiple stage nitrous solenoids.

    Installation Instructions (PDF)

  • MSD 8190 10 Male Pins and Seals
    $8.99
    $9.99
    New
    MSD 8190 10 Male Pins and Seals
    SKU-5478190
    x
                Male pins and seals for use with Weathertight Connectors.
            
  • MSD 8187 4-Pin Deutsch Connector, 12-14 gauge
    New
    MSD 8187 4-Pin Deutsch Connector, 12-14 gauge
    SKU-5478187
    x
                There is absolutely no excuse for losing a race due to a poor wiring connection. MSDs Deutsch Connectors are sealed and lock together making them perfect for harsh racing applications. The compact housing of the connectors are molded from a durable plastic material that will not harden or crack. Each housing is indexed to prevent any chance of mismatching the ends plus they have a molded channel to secure another connector for a tidy appearance.The terminals grip to the wire with strong crimp tabs then lock into position inside the housing. The connections are protected with thick seals that will keep water, mud and debris away from the contacts. These terminals can handle more current than conventional connectors and do not require special tools. Supplied with terminals, seals and housings.

    Installation Instructions (PDF)

    • Sealed Connectors
  • MSD 8184 2-Pin Deutsch Connector, 12-14 gauge
    New
    MSD 8184 2-Pin Deutsch Connector, 12-14 gauge
    SKU-5478184
    x
                There is absolutely no excuse for losing a race due to a poor wiring connection. MSDs Deutsch Connectors are sealed and lock together making them perfect for harsh racing applications. The compact housing of the connectors are molded from a durable plastic material that will not harden or crack. Each housing is indexed to prevent any chance of mismatching the ends plus they have a molded channel to secure another connector for a tidy appearance.The terminals grip to the wire with strong crimp tabs then lock into position inside the housing. The connections are protected with thick seals that will keep water, mud and debris away from the contacts. These terminals can handle more current than conventional connectors and do not require special tools. Supplied with terminals, seals and housings.

    Installation Instructions (PDF)

    • Waterproof
    • Quick Connect
  • MSD 8910 Tach Adapter
    $42.99
    $50.99
    New
    MSD 8910 Tach Adapter
    SKU-5478910
    x
                If, after installing an MSD Ignition Control, your ta�chometer, fuel pump relay or electronic fuel injection (in foreign vehicles) doesnt operate correctly, your ap�plication may require a Tach Adapter. This is due to the trigger signal not being strong enough to trigger both the MSD and the factorys components.There are a few Tach Adapters available and for more information see pages 152 and 153. Each Adapter is simple to wire in and will have your MSD and vehicle firing away in no time! If you are triggering an MSD Blaster, 5, 6, SCI, or 7 Series Ignition with its white wire or points terminal, you will need the PN 8910 Tach Adapter. The PN 8910 will correct the operation of most voltage-triggered tachometers or fuel injection systems that do not work directly off the tach output terminal of the MSD Ignition Unit.

    Installation Instructions (PDF)

    Installation Instructions (PDF)

    • Longacre 44611 Flip-Up Start/Ignition Switch Panel w/Pilot Light
      Longacre 44611 Flip-Up Start/Ignition Switch Panel w/Pilot Light
      SKU-47544611
      x
                  These high capacity (40 amp at 12 volts) ignition switch panels with aircraft style cover and pilot light are easy to turn off in an emergency from any angle, even with gloves. Will not turn off from vibration. They come pre-wired with high insulation "Fat" wires and soldered terminals with heat shrinked seals.
      • Starter button with weatherproof cover
      • Lightweight aluminum panel
      • Plugs into Longacre wiring harness P/N 44930
      • Ignition Switch:
        • Style:    Toggle
        • Cover:    Aircraft style flip
        • Pilot Light Included:   Yes
        • Rating:    40 amps @ 12 volts
      • Starter Switch:
        • Style:    Push button
        • Cover:    Weatherproof rubber
        • Rating:    15 amps @ 12 volts resistive
      • Panel:
        • Material:    Lightweight aluminum
        • Panel Dimensions:   3-1/2" x 3-1/2"
        • Wiring Included:    Yes
    • Toggle Ignition On Switch
      $9.99
      Product Rating: 4.75 Stars
      Toggle Ignition On Switch
      SKU-91364380
      x
                  Toggle switch works great as a kill switch or with other auxiliary equipment. 25 amp SPST switch with rubber boot and on/off plate.
              
    • Safety Kill Switch
      $19.99
      Product Rating: 4.50 Stars
      Safety Kill Switch
      SKU-91364384
      x
                  

      This is the best kill switch we've found! Works with standard ignition only. Water resistant with O-ring shaft seal. Pull on, push off with silver contacts.

      20 amp rating at 12 VDC.

    • MSD 8180 6- Pin Deutsch Connector, 16 gauge
      New
      MSD 8180 6- Pin Deutsch Connector, 16 gauge
      SKU-5478180
      x
                  There is absolutely no excuse for losing a race due to a poor wiring connection. MSDs Deutsch Connectors are sealed and lock together making them perfect for harsh racing applications. The compact housing of the connectors are molded from a durable plastic material that will not harden or crack. Each housing is indexed to prevent any chance of mismatching the ends plus they have a molded channel to secure another connector for a tidy appearance.The terminals grip to the wire with strong crimp tabs then lock into position inside the housing. The connections are protected with thick seals that will keep water, mud and debris away from the contacts. These terminals can handle more current than conventional connectors and do not require special tools. Supplied with terminals, seals and housings.

      Installation Instructions (PDF)

      • Waterproof
      • Heat Shrinkable
      • Battery Quick Disconnects
      • Special Tools
      • Perma-Seal
      • Weather Pack
      • Deutsch
      • Quick Connect
    • MSD 8956 Window RPM Activated Switch
      $87.99
      $112.99
      New
      MSD 8956 Window RPM Activated Switch
      SKU-5478956
      x
                  These RPM-Activated Switches will perform a variety of different functions from turning on a bulb or solenoid to activating an MSD Timing Control at a desired rpm.The RPM-Activated Switch, PN 8950, has two activation wires; one to ground a circuit and the other to open a circuit. Simply plug in an rpm module and wire the Switch to the circuit you want to activate. When the engine rpm reaches that amount, the circuit is activated and will remain on until the rpm falls below that amount.The RPM Window Switch, PN 8956, has two rpm adjustments; one to activate a circuit, while the other deactivates the same circuit. This Switch will supply then remove ground to a circuit. This is a great feature to deactivate nitrous before the engines rev limit is reached. Both Switches can be used with stock inductive ignitions or an MSD Ignition and can handle up to 1.5 amps. No rpm modules are supplied so they must be ordered from the selection of Modules shown here. For use on 4, 6, or 8-cylinder engines.

      Installation Instructions (PDF)

      • 2 RPM Adjustments
      • Activate a circuit
      • Deactivate a circuit
    • MSD 8920 Tach Adapter, Magnetic Trigger
      $60.99
      $77.99
      New
      MSD 8920 Tach Adapter, Magnetic Trigger
      SKU-5478920
      x
                  If, after installing an MSD Ignition Control, your ta�chometer, fuel pump relay or electronic fuel injection (in foreign vehicles) doesnt operate correctly, your ap�plication may require a Tach Adapter. This is due to the trigger signal not being strong enough to trigger both the MSD and the factorys components.There are a few Tach Adapters available and for more information see pages 152 and 153. Each Adapter is simple to wire in and will have your MSD and vehicle firing away in no time! If you are using the magnetic pick-up input (green and violet wires) to trigger your MSD Ignition, you will need the PN 8920 Tach Adapter. The PN 8920 will correct the operation of most voltage-triggered tachometers that do not work directly off the tach output terminal of the MSD Control. This Adapter should also be used on current-triggered tachs (hooked in series with the ignition switch).

      Installation Instructions (PDF)

      • If you are connecting a tachometer to an MSD Ignition, or your application is equipped with electronic fuel injection then you may need to use this Tach/Fuel Injection Adapter to ensure correct operation. This Adapter will correct the operation of most tachometers and fuel injection pump relays that do not work directly off of the MSD Ignitions 12 volt square wave tach output terminal.
    • Painless Wiring 70402 Two Wire Weatherpack Connectors
      Painless Wiring 70402 Two Wire Weatherpack Connectors
      SKU-91012212
      x
                  

      A real water-tight connection. Each number consists of one male and one female component. Accepts 14 - 16 gauge wire.

    • MSD 8812 Universal, Push Button, Alt. Action Switch
      New
      MSD 8812 Universal, Push Button, Alt. Action Switch
      SKU-5478812
      x
                  This switch is designed to be used as an auxiliary ignition On/Off but�ton. It can be mounted to the steering wheel within easy reach of the driver and can be used in a Normally Open or Normally Closed position. Assembled and constructed for harsh racing conditions.

      Installation Instructions (PDF)

      • Speedway Starter Switch Panel
        Speedway Starter Switch Panel
        SKU-91364385
        x
                    

        Start your engine by flicking a switch and depressing a starter button. This starter switch panel is designed to stand up to rough racing conditions and is fully waterproof.

        • Panel measures 2-5/8" x 4-1/2"
        • Includes three 14 gauge wires (5 ft. each)

        913-64385 Instructions (PDF)

      • Keep It Clean Switch Panel
        $74.99
        Product Rating: 5.00 Stars
        Keep It Clean Switch Panel
        SKU-91029085
        x
                    
        • Push button start
        • Battery kill switch
        • 3 Heavy duty accessory toggle switches with cover
        • Aluminum mounting plate
        • Indicator lights
        • Measures 7.5" x 2.5"
      • Lokar 1110118 Dial-In Board 1-5/8 Inch Cage Mount - Clear
        New
        Lokar 1110118 Dial-In Board 1-5/8 Inch Cage Mount - Clear
        SKU-4911110118
        x
                    

        This 3-digit dial in board from Lokar comes with a bracket. This mount fits a 1-5/8" diameter tube.

        • 6061 T-6 Aluminum
        • No welding or drilling required
        • No interference with roll-bar padding
        • Adjustable arm for leveling
        • Made in the USA
      • AFCO 85005B Afco Master Disconnect Panel
        AFCO 85005B Afco Master Disconnect Panel
        SKU-10685005B
        x
                    
                
      • Longacre 44661 Flip-Up Start/Ignition Panel w/ 1 ACC and Pilot Light
        Longacre 44661 Flip-Up Start/Ignition Panel w/ 1 ACC and Pilot Light
        SKU-47544661
        x
                    These high capacity (40 amp at 12 volts) ignition switch panels with aircraft style cover and pilot light are easy to turn off in an emergency from any angle, even with gloves. Will not turn off from vibration. They come pre-wired with high insulation "Fat" wires and soldered terminals with heat shrinked seals.
        • Starter button with weatherproof cover
        • Lightweight aluminum panel
        • Plugs into Longacre wiring harness P/N 44930
        • Ignition Switch:
          • Style:    Toggle
          • Cover:    Aircraft style flip
          • Pilot Light Included:   Yes
          • Rating:    40 amps @ 12 volts
        • Starter Switch:
          • Style:    Push button
          • Cover:    Weatherproof rubber
          • Rating:    15 amps @ 12 volts resistive
        • Accessory Switch:
          • Quantity Included:    1
          • Style:    Toggle
          • Cover:    Silicon rubber
          • Pilot Lights Included:    Yes
          • Rating:    40 amps @ 12 volts
        • Panel:
          • Material:    Lightweight aluminum
          • Panel Dimensions:   3-1/2" x 3-1/2"
          • Wiring Included:    Yes
      • Lokar 1110107 Dial-In Board 1-1/2 Inch Cage Mount - Black
        New
        Lokar 1110107 Dial-In Board 1-1/2 Inch Cage Mount - Black
        SKU-4911110107
        x
                    

        This 3 digit dial-in board from Lokar comes with a bracket.  It is designed to fit 1-1/2" diameter tubes.

        • Anodized Black
        • No welding or drilling required
        • No interference with roll-bar padding
        • 6061 T-6 Aluminum
        • Made in the USA
      • Painless Wiring 40007 Three Wire Quick Connect Terminal
        Painless Wiring 40007 Three Wire Quick Connect Terminal
        SKU-91012201
        x
                    

        Make your own locking quick connect plugs easily and quickly. Each kit contains one male and one female component. Accept 10 - 20 gauge wire.

      • Auto Meter 990340 Right Angle Reversing Adapter for Cobra Speedometers
        Auto Meter 990340 Right Angle Reversing Adapter for Cobra Speedometers
        SKU-182990340
        x
                    

        These quality made adapters are designed for use with Cobra series speedometers that require reverse cable rotation for proper operation. They accept the standard 5/8" thread-on speedometer cable and are designed for use at the back of the instrument, not intended for installation on the transmission.

        • For Cobra series speedometers that require reverse cable rotation
        • Accepts standard 5/8 in. speedo cable
      • Monster 1 Inch Warning Light Only
        Monster 1 Inch Warning Light Only
        SKU-60452
        x
                    

        Shows problem before it becomes a hazard with these easy to install and easy to see 1" LED replacement lights.

        O.D. is 1-3/8" and total length is 2".

      • Painless Wiring 40021 Jamb Tac Door Jamb Connector, 1 Wire
        Painless Wiring 40021 Jamb Tac Door Jamb Connector, 1 Wire
        SKU-91040021
        x
                    No more ugly wires! Don't wire it... Jamb Tac it! These spring loaded electrical contacts eliminate those ugly wires running into your doors. One pair contains enough parts for one door. One piece installs in the door and one piece installs in the door jam.

        The contact buttons on these jamb tac kits are adjustable in length or depth from 0" to 3/8".
      • AFCO 85266 HD Starter Button
        $12.99
        AFCO 85266 HD Starter Button
        SKU-10685266
        x
                    Afco HD Starter Button 
                
      • Lokar 1110134 Adjustable Angle Mount for MEGA Dial-In Board -Polished
        New
        Lokar 1110134 Adjustable Angle Mount for MEGA Dial-In Board -Polished
        SKU-4911110134
        x
                    

        This 4-digit mega dial-in board mount comes with a bracket. The bracket is a universal bolt-on adjustable angle mount.

        • 6061 Aluminum
        • No welding or drilling reuqred
        • No interference with roll-bar padding
        • Made in the USA
        • Adjustable arm for leveing
      • AFCO 85298 Ignition Warning Light
        AFCO 85298 Ignition Warning Light
        SKU-10685298
        x
                    

        AFCO Ignition Warning Light

        - .640 O.D. on chrome ring
        - Mounts in 1/2" hole

      • AFCO 85294 Warning Light, Fuel Pressure
        AFCO 85294 Warning Light, Fuel Pressure
        SKU-10685294
        x
                    

        These lights allow the driver to maintain focus on the race.

        Wiring Instructions (PDF)

      • Painless Wiring 40006 Two Wire Quick Connect Terminals
        Painless Wiring 40006 Two Wire Quick Connect Terminals
        SKU-91012200
        x
                    

        Make your own locking quick connect plugs easily and quickly. Each kit contains one male and one female component. Accept 10 - 20 gauge wire.

      • MSD 8181 4-Pin Deutsch Connector, 16 gauge
        New
        MSD 8181 4-Pin Deutsch Connector, 16 gauge
        SKU-5478181
        x
                    There is absolutely no excuse for losing a race due to a poor wiring connection. MSDs Deutsch Connectors are sealed and lock together making them perfect for harsh racing applications. The compact housing of the connectors are molded from a durable plastic material that will not harden or crack. Each housing is indexed to prevent any chance of mismatching the ends plus they have a molded channel to secure another connector for a tidy appearance.The terminals grip to the wire with strong crimp tabs then lock into position inside the housing. The connections are protected with thick seals that will keep water, mud and debris away from the contacts. These terminals can handle more current than conventional connectors and do not require special tools. Supplied with terminals, seals and housings.

        Installation Instructions (PDF)

        • Waterproof
        • Quick Connect
      • MSD 8174 1-Pin Weathertight Connector, 1 qty
        New
        MSD 8174 1-Pin Weathertight Connector, 1 qty
        SKU-5478174
        x
                    If you need electrical connectors that are unaffected by water, chemicals, vibration, temperature or dirt, and that will not come apart accidentally, then you need MSD Weathertight Connectors.The Weathertight connectors are molded from a special nylon material to withstand temperatures from -40° to +257°F and are indexed to prevent mismatching. Positive locks let you know when the connectors are completely joined by producing an audible CLICK. No click means no connection.For maximum electrical isolation, each terminal has its own tower so there is no chance of shorting between the wires. Each terminal tower utilizes self-lubricating silicone seals for protection against water, dust, oil, and other engine compartment fluids.
                
      • AFCO 85030B Starter Switch Panel, 4-1/8 x 5-7/8 Inch
        AFCO 85030B Starter Switch Panel, 4-1/8 x 5-7/8 Inch
        SKU-10685030B
        x
                    

        AFCO starter switch panels are for standard ignitions.

        Wiring Instructions (PDF)

      • RACEceiver Stereo Splitter
        $9.99
        RACEceiver Stereo Splitter
        SKU-910150503
        x
                    

        This small splitter allows any RACEceiver to power 2 headsets simultaneously!

        • Standard 3.5 mm input and output
      • Afco 8000044402 Universal Dual Cooling Fan Wire Harness, 40 Amp Relays
        New
        Afco 8000044402 Universal Dual Cooling Fan Wire Harness, 40 Amp Relays
        SKU-1068000044402
        x
                    These heavy duty dual fans wire harness kits from Afco are designed  as a universal kit for positive or negative controlled units.  They  feature 40 amp relays, heavy gauge wiring, and all connectors needed.
        • Hardware included
        • Color installation instructions included
        • 40 amp relays
        • Positive or Negative controlled
        • Universal for dual cooling fans
        • Temp switch sold seperately
      • Snap Spade Style Terminals, 6-32 Yellow, 12-10 Gauge
        Snap Spade Style Terminals, 6-32 Yellow, 12-10 Gauge
        SKU-91055674
        x
                    
        • Works with 12-10 Ga wire
        • Vinyl Snap Spade #6-32 
        • Comes in a package of 100
      • MSD 8186 12-Pin Deutsch Connector, 16 gauge
        New
        MSD 8186 12-Pin Deutsch Connector, 16 gauge
        SKU-5478186
        x
                    There is absolutely no excuse for losing a race due to a poor wiring connection. MSDs Deutsch Connectors are sealed and lock together making them perfect for harsh racing applications. The compact housing of the connectors are molded from a durable plastic material that will not harden or crack. Each housing is indexed to prevent any chance of mismatching the ends plus they have a molded channel to secure another connector for a tidy appearance.The terminals grip to the wire with strong crimp tabs then lock into position inside the housing. The connections are protected with thick seals that will keep water, mud and debris away from the contacts. These terminals can handle more current than conventional connectors and do not require special tools. Supplied with terminals, seals and housings.

        Installation Instructions (PDF)

      • AFCO Master Disconnect Switch, 2-Post
        AFCO Master Disconnect Switch, 2-Post
        SKU-10685268
        x
                    Remote battery disconnect switch for safety requirements. A battery kill switch is required for use with alternators by the NHRA. Battery shut off switch can be remote mounted or where specified for saftey and convenience.
        • 125 amp intermittent load (15 seconds)
        • 20 amp continuous service
        • 6 volt to 36 volt systems
        • 2-position switch
        • Die cast lever
        • Fits panel through 3/16" thick
      Goto Previous PagePrevious Page
      1 2 3 4