Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Oval Track Electric Switches & Connectors At Speedway Motors

Find all your race car switch panels, warning lights and wiring accessories at Speedway Motors - America's Racing Super Market. Speedway Motors stocks many of the most dependable brands in the racing industry, including AFCO, Longacre and Painless Wiring. Shop now for same day shipping on these oval track racing electrical components!

Featured Products
Two Post Battery Disconnect Switch
Two Post Battery Disconnect Switch
x
            Remote battery disconnect switch for safety and theft protection. A battery kill switch is required for use with alternators by the NHRA. Battery shut off switch can be remote mounted or where specified for saftey and  convenience.
  • 180 amp continuous, 1000 amp instantaneous
  • Die cast lever
  • Fits panel through 3/16" thick

910-64500 Instructions (PDF)

Toggle Ignition On Switch
$9.99
Product Rating: 4.50 Stars
Toggle Ignition On Switch
x
            Toggle switch works great as a kill switch or with other auxiliary equipment. 25 amp SPST switch with rubber boot and on/off plate.
        
Universal Relay for Fan/Horn
$16.99
Product Rating: 5.00 Stars
Universal Relay for Fan/Horn
x
            

This heavy duty relay takes the heavy-amp load off the switch, thus preventing an overheated circuit and a possible wiring harness fire. Works well with electric fans and horn circuits too. 30 amp relay.

The wiring for the relay is as follows:

  • Short Red Wire (from relay post 87) = power lead to horn or fan
  • Long Red Wire (from relay post 30) = main power supply in
  • Short Black Wire (from relay post 85) = makes ground connection thru a temp sensitive switch or a grounding horn button
  • Long Gray Wire (from relay post 86) = connects to switched 12 volt power (like ignition switch) so horn or fan turns on/off with key

Includes relay, circuit breaker, wire, terminals and instructions.

Universal Fan Relay Installation Instructions (PDF)

Auto Meter 5289 GPS Sending Module-Universal for Electric Speedometers
Auto Meter 5289 GPS Sending Module-Universal for Electric Speedometers
x
            

This unit allows nearly any electric speedometer to use free GPS signals to drive the speedometer. No more cables, no more calibration drives. If you've got an Auto Meter electronic speedometer, it's a plug and play solution. Calibration on non-Auto Meter speedometers takes about 10 seconds and doesn't require driving. The Module uses the fastest possible GPS technology for truly seamless functionality.

  • Lightning fast 10Hz Signal
  • Separate paintable 1" square antenna with optional magnetic attachment capability
  • Waterproof antenna and module assembly (IP67 sealed)
  • Factory calibrated for 16,000 pulses per mile
  • One touch calibration
  • Compatible with Electronic Speedometers Only

"Oval Track, Electrical, Lighting and Body" Page 1 of 3

  • Safety Kill Switch
    $19.99
    Product Rating: 5.00 Stars
    Safety Kill Switch
    x
                

    This is the best kill switch we've found! Works with standard ignition only. Water resistant with O-ring shaft seal. Pull on, push off with silver contacts.

    20 amp rating at 12 VDC.

  • Painless Wiring 70402 Two Wire Weatherpack Connectors
    Painless Wiring 70402 Two Wire Weatherpack Connectors
    x
                

    A real water-tight connection. Each number consists of one male and one female component. Accepts 14 - 16 gauge wire.

  • Speedway Starter Switch Panel
    Speedway Starter Switch Panel
    x
                

    Start your engine by flicking a switch and depressing a starter button. This starter switch panel is designed to stand up to rough racing conditions and is fully waterproof.

    • Panel measures 2-5/8" x 4-1/2"
    • Includes three 14 gauge wires (5 ft. each)

    913-64385 Instructions (PDF)

  • Keep It Clean Switch Panel
    $74.99
    Product Rating: 5.00 Stars
    Keep It Clean Switch Panel
    x
                
    • Push button start
    • Battery kill switch
    • 3 Heavy duty accessory toggle switches with cover
    • Aluminum mounting plate
    • Indicator lights
    • Measures 7.5" x 2.5"
  • AFCO 85298 Ignition Warning Light
    AFCO 85298 Ignition Warning Light
    x
                

    AFCO Ignition Warning Light

    - .640 O.D. on chrome ring
    - Mounts in 1/2" hole

  • AFCO Master Disconnect Switch, 2-Post
    AFCO Master Disconnect Switch, 2-Post
    x
                Remote battery disconnect switch for safety requirements. A battery kill switch is required for use with alternators by the NHRA. Battery shut off switch can be remote mounted or where specified for saftey and convenience.
    • 125 amp intermittent load (15 seconds)
    • 20 amp continuous service
    • 6 volt to 36 volt systems
    • 2-position switch
    • Die cast lever
    • Fits panel through 3/16" thick
  • Painless Wiring 40008 Four Wire Quick Connect Terminal
    Painless Wiring 40008 Four Wire Quick Connect Terminal
    x
                

    Make your own locking quick connect plugs easily and quickly. Each kit contains one male and one female component. Accept 10 - 20 gauge wire.

  • MSD 8985 Timing Tapes
    $5.99
    Product Rating: 4.50 Stars
    MSD 8985 Timing Tapes
    x
                

    MSD's timing tape set comes with eight different tapes to fit balancers from 5-1/4" to 8" diameters.

  • Moroso 26100 Distributor Timing Indicator
    Moroso 26100 Distributor Timing Indicator
    x
                

    Fast and accurate method of adjusting ignition timing without use of a timing light. Change timing quickly between heats. Fits all Chevy V8 and 90° V6 distributors. May require minor modification to some manifolds.

    545-26100 Instructions (PDF)

  • DPDT Momentary Toggle Switch
    $14.99
    DPDT Momentary Toggle Switch
    x
                

    Universal heavy duty 3-position momentary toggle switch. Features a nickel-plated brass switch, phenolic housing, and plated steel cap. Rated at 25A at 12V, 15A at 24V, and 10A at 36V DC.

    • Mounting Stem:  15/32" -32 thread, 15/32" long, and fits panels up to 9/32"
    • Six Screw Terminals:  6-32 screws
    • Electrical Rating:  25A at 12V, 15A at 24V, and 10A at 36V DC

    Works great as a linear actuator switch!

    Note: Up=Momentary On, Center=Off, Down=Momentary On.

  • Double Throw Toggle Switch with Boot
    Double Throw Toggle Switch with Boot
    x
                

    Single pole, double throw. On-On configuration. Plastic housing with steel plate. Rubber boot protects switch from dirt and moisture. This toggle switch requires a 1/2" hole to mount it.

    • Three terminals
    • Two toggle positions
    • Rated for 25 amps at 12 volts DC

     

  • Painless Wiring 40024 Jamb Tac Door Jamb Connector, 4 Wire
    Painless Wiring 40024 Jamb Tac Door Jamb Connector, 4 Wire
    x
                No more ugly wires! Don't wire it... Jamb Tac it! These spring loaded electrical contacts eliminate those ugly wires running into your doors. One pair contains enough parts for one door. One piece installs in the door and one piece installs in the door jam.

    The contact buttons on these jamb tac kits are adjustable in length or depth from 0" to 3/8".
  • Electrical 4 Terminal Block Strip
    $4.99
    $5.99
    Electrical 4 Terminal Block Strip
    x
                

    Connect all the wires in your panel or enclosure in one convenient place. Also known as barrier terminal strips, these blocks have screw terminals—just loosen a screw and wrap a stripped wire end around it (or use a spade terminal) and tighten the screw. All have four mounting holes. Color is black. UL recognized and CSA certified.

    • Phenolic block 
    • Tin-plated brass terminals
    • Ni-plated steel screws
    • Amps Per Circuit: 20A
    • For Wire Size, AWG: 22-12
    • Screw Terminal Size: #6-32
    • Center-to-Center:  0.38"
    • Mount Hole Diameter:  0.17"

    Note: These are terminal strips and are NOT intended for use as ground strips. To be used as a ground strip, all terminals on one side would need to be pigtailed together.

  • Auto Meter 9118 Tach Adapter
    $92.99
    Auto Meter 9118 Tach Adapter
    x
                

    One of the problems with magnetos is the limited choices of tachs that work with them. This little box allows you to run almost any tachometer with your magneto. Requires 12 volts.

    Magneto Tach Adapter Installation Instructions (pdf)

  • Performance Distributors 222222 Battery/Tach Connector Tool
    Performance Distributors 222222 Battery/Tach Connector Tool
    x
                

    Disconnect tool for use with DUI Battery and Tachometer Connector 910-13201.

  • AFCO 85260 HD 25 Amp Ignition/Accessory Switch
    AFCO 85260 HD 25 Amp Ignition/Accessory Switch
    x
                

    AFCO heavy duty 25 Amp ignition or accessory switch.

    Wiring Instructions (PDF)

  • AFCO 85290 Warning Light, Oil Pressure
    AFCO 85290 Warning Light, Oil Pressure
    x
                

    These lights allow the driver to maintain focus on the race.

    Wiring Instructions (PDF)

  • Classic Instruments SN57F Ford Oil Pressure Sender Bushing Kit Adaptor
    Classic Instruments SN57F Ford Oil Pressure Sender Bushing Kit Adaptor
    x
                Classic Instruments' brass angled-bushing kits allow for easy installation on most Ford engines. 

    The Oil Pressure Sender will not clear either the back of the intake manifold or the distributor body on many installations unless the Bushing Kit is used.

    • Bushing kit to install oil pressure sender
    • Ford applications
  • Budget 40-Amp Relay Kit
    $9.99
    Product Rating: 4.63 Stars
    Budget 40-Amp Relay Kit
    x
                

    Use this handy 40 amp relay to wire up your 12 volt horn, electric fuel pump, electric fan with sensor, shaved door handles, or whatever! Contains relay, plug, wire, and instructions.

    The wiring would be as follows (included in kit instructions):

    • Red Wire #30 Prong = main 12V power source
    • Black Wire #85 Prong = Electric fan sensor OR low (oil) pressure switch OR grounding switch
    • Blue Wire #86 Prong = 12V toggle switch OR ignition switch "ACC" terminal
    • Yellow Wire #87 Prong = to fan or fuel pump + lead
    • White Wire or Center Prong = not normally used 

    Fan or Fuel Pump Relay Installation Instructions (PDF)

  • Yellow Vinyl Butt Connectors, 12-10 Gauge
    Yellow Vinyl Butt Connectors, 12-10 Gauge
    x
                

    Secure loose/spliced wire ends to each other with these vinyl butt connectors.

    • Comes in a package of 100
  • AFCO 85193 Warning Light Kit, Oil Temp.
    AFCO 85193 Warning Light Kit, Oil Temp.
    x
                

    These units allow the driver to maintain focus on the race.

    Wiring Instructions (PDF)

  • Two Post Battery Disconnect Switch
    Two Post Battery Disconnect Switch
    x
                Remote battery disconnect switch for safety and theft protection. A battery kill switch is required for use with alternators by the NHRA. Battery shut off switch can be remote mounted or where specified for saftey and  convenience.
    • 180 amp continuous, 1000 amp instantaneous
    • Die cast lever
    • Fits panel through 3/16" thick

    910-64500 Instructions (PDF)

  • Performance Distributors 111111 Battery and Tachometer Connector
    Performance Distributors 111111 Battery and Tachometer Connector
    x
                

    These plastic insulators and brass terminals make your power supply connection and tach connection to the DUI Distributor super easy! They plug directly into the cap and coil assembly and the locking tabs prevent lost connections due to vibration. The Battery and Tachometer Connectors are priced separately so one of each will be needed for the hot wire and tach hookup.

  • Auto Meter 5289 GPS Sending Module-Universal for Electric Speedometers
    Auto Meter 5289 GPS Sending Module-Universal for Electric Speedometers
    x
                

    This unit allows nearly any electric speedometer to use free GPS signals to drive the speedometer. No more cables, no more calibration drives. If you've got an Auto Meter electronic speedometer, it's a plug and play solution. Calibration on non-Auto Meter speedometers takes about 10 seconds and doesn't require driving. The Module uses the fastest possible GPS technology for truly seamless functionality.

    • Lightning fast 10Hz Signal
    • Separate paintable 1" square antenna with optional magnetic attachment capability
    • Waterproof antenna and module assembly (IP67 sealed)
    • Factory calibrated for 16,000 pulses per mile
    • One touch calibration
    • Compatible with Electronic Speedometers Only
  • Longacre 44897 Carbon Fiber Starter Switch Panel, Cover & Master Switch
    Longacre 44897 Carbon Fiber Starter Switch Panel, Cover & Master Switch
    x
                

    This composite panel is made of lightweight molded ABS featuring a carbon fiber pattern that matches Longacre's new composite gauge panels. The starter panel features a high capacity ignition switch with a aircraft style cover. The ignition switch is easy to turn off in an emergency but will not turn off from vibrations. Starter button has a rubber switch boot to seal out moisture. Manual battery disconnect switch features a bright red panel for easy disconnect during an emergency.

    • Great looking Composite Panel - Lightweight molded ABS with a carbon fiber pattern
    • Matches our new Composite Gauge Panels
    • High capacity ignition switch with weatherproof cover and pilot light
    • Starter button with rubber switch boot to seal out moisture
    • Assembled and wired, 40 amp @ 12v DC
    • Plugs into Longacre wiring harness (not included)
    • Pre-wired with high insulation 'Fat' wires and soldered terminals with heat shrink seals
    • Manual battery disconnect switch with a bright red handle
    • Easier to find in an emergency
    • Prevents battery drain
    • 175 amp continuous rating, 6-36 volt, 1000 peak
  • Push Button Starter Switch
    $5.99
    Product Rating: 4.80 Stars
    Push Button Starter Switch
    x
                

    Momentary switch has rubber boot which protects switch from moisture. Easy install to give any classic car that hot rod feel. Features a high quality die cast zinc housing with brass terminals.

  • Electrical 8 Terminal Block Strip
    $5.99
    $6.99
    Electrical 8 Terminal Block Strip
    x
                

    Connect all the wires in your panel or enclosure in one convenient place. Also known as barrier terminal strips, these blocks have screw terminals—just loosen a screw and wrap a stripped wire end around it (or use a spade terminal) and tighten the screw. All have four mounting holes. Color is black. UL recognized and CSA certified.

    • Phenolic block 
    • Tin-plated brass terminals
    • Ni-plated steel screws
    • Amps Per Circuit: 20A
    • For Wire Size, AWG: 22-12
    • Screw Terminal Size: #6-32
    • Center-to-Center:  0.38"
    • Mount Hole Diameter:  0.17"

    Note: These are terminal strips and are NOT intended for use as ground strips. To be used as a ground strip, all terminals on one side would need to be pigtailed together.

  • Painless Wiring 40009 Six Wire Quick Connect Terminal
    Painless Wiring 40009 Six Wire Quick Connect Terminal
    x
                

    Make your own locking quick connect plugs easily and quickly. Each kit contains one male and one female component. Accept 10 - 20 gauge wire.

  • AFCO 85293 Warning Light, Oil Temp.
    AFCO 85293 Warning Light, Oil Temp.
    x
                

    These lights allow the driver to maintain focus on the race.

    Wiring Instructions (PDF)

  • Longacre 44611 Flip-Up Start/Ignition Switch Panel w/Pilot Light
    Longacre 44611 Flip-Up Start/Ignition Switch Panel w/Pilot Light
    x
                These high capacity (40 amp at 12 volts) ignition switch panels with aircraft style cover and pilot light are easy to turn off in an emergency from any angle, even with gloves. Will not turn off from vibration. They come pre-wired with high insulation "Fat" wires and soldered terminals with heat shrinked seals.
    • Starter button with weatherproof cover
    • Lightweight aluminum panel
    • Plugs into Longacre wiring harness P/N 44930
    • Ignition Switch:
      • Style:    Toggle
      • Cover:    Aircraft style flip
      • Pilot Light Included:   Yes
      • Rating:    40 amps @ 12 volts
    • Starter Switch:
      • Style:    Push button
      • Cover:    Weatherproof rubber
      • Rating:    15 amps @ 12 volts resistive
    • Panel:
      • Material:    Lightweight aluminum
      • Panel Dimensions:   3-1/2" x 3-1/2"
      • Wiring Included:    Yes
  • Toggle Ignition On Switch
    $9.99
    Product Rating: 4.50 Stars
    Toggle Ignition On Switch
    x
                Toggle switch works great as a kill switch or with other auxiliary equipment. 25 amp SPST switch with rubber boot and on/off plate.
            
  • AFCO 85005B Afco Master Disconnect Panel
    AFCO 85005B Afco Master Disconnect Panel
    x
                
            
  • Longacre 44661 Flip-Up Start/Ignition Panel w/ 1 ACC and Pilot Light
    Longacre 44661 Flip-Up Start/Ignition Panel w/ 1 ACC and Pilot Light
    x
                These high capacity (40 amp at 12 volts) ignition switch panels with aircraft style cover and pilot light are easy to turn off in an emergency from any angle, even with gloves. Will not turn off from vibration. They come pre-wired with high insulation "Fat" wires and soldered terminals with heat shrinked seals.
    • Starter button with weatherproof cover
    • Lightweight aluminum panel
    • Plugs into Longacre wiring harness P/N 44930
    • Ignition Switch:
      • Style:    Toggle
      • Cover:    Aircraft style flip
      • Pilot Light Included:   Yes
      • Rating:    40 amps @ 12 volts
    • Starter Switch:
      • Style:    Push button
      • Cover:    Weatherproof rubber
      • Rating:    15 amps @ 12 volts resistive
    • Accessory Switch:
      • Quantity Included:    1
      • Style:    Toggle
      • Cover:    Silicon rubber
      • Pilot Lights Included:    Yes
      • Rating:    40 amps @ 12 volts
    • Panel:
      • Material:    Lightweight aluminum
      • Panel Dimensions:   3-1/2" x 3-1/2"
      • Wiring Included:    Yes
  • Painless Wiring 40007 Three Wire Quick Connect Terminal
    Painless Wiring 40007 Three Wire Quick Connect Terminal
    x
                

    Make your own locking quick connect plugs easily and quickly. Each kit contains one male and one female component. Accept 10 - 20 gauge wire.

  • Auto Meter 990340 Right Angle Reversing Adapter for Cobra Speedometers
    Auto Meter 990340 Right Angle Reversing Adapter for Cobra Speedometers
    x
                

    These quality made adapters are designed for use with Cobra series speedometers that require reverse cable rotation for proper operation. They accept the standard 5/8" thread-on speedometer cable and are designed for use at the back of the instrument, not intended for installation on the transmission.

    • For Cobra series speedometers that require reverse cable rotation
    • Accepts standard 5/8 in. speedo cable
  • Monster 1 Inch Warning Light Only
    Monster 1 Inch Warning Light Only
    x
                

    Shows problem before it becomes a hazard with these easy to install and easy to see 1" LED replacement lights.

    O.D. is 1-3/8" and total length is 2".

Goto Previous PagePrevious Page
1 2 3