Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 27

Products

Driveline and Axles

Shop Oval Track Driveline & Axles At Speedway Motors

Every racer knows that having huge horsepower is worthless if you can't get it to the wheels. Speedway Motors has the driveline parts you need to put the power to the pavement! From Curries Axles to Fast Shaft Drive Shafts and everything in between, you can count on Speedway Motors to have the parts you need in-stock and ready to ship today!

Featured Products
  • 9 Inch Ford Rear End Overhaul Kit
    9 Inch Ford Rear End Overhaul Kit
    (Part #9190950)
    x
                This 9" Ford overhaul kit includes: pinion pilot, pinion shaft, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear marking grease, brush and Loctite. Ring gear bolts not included. 

    NOTE: All Ford 9" full spools use overhaul kit 9190950-31, even if they are a 28-spline spool. The 9190950-31 contains the large I.D. standard O.D. carrier bearings and pinion bearings needed for use with our full spools.

    If you are using the H.D. nodular iron center section which uses the large diameter carrier bearings, order kit 9190950-31s, which also includes the large pinion bearings for use with the Daytona pinion support.

    9" Ford Carrier Bearing Chart (GIF)  - Double check your bearing p/n.

  • 1/2 Inch Aluminum Nylock Bolt Nuts, 10 Pack
    1/2 Inch Aluminum Nylock Bolt Nuts, 10 Pack
    (Part #94004243)
    x
                

    1/2 Inch Aluminum Nylock Bolt Nuts, 10 Pack

    • 1/2"-20
    • Aluminum
    • Nylon insert
    • 10 pack

     

  • Seals-It EAS1-05 Universal Inner Axle Seal for 2.5-2.75 Inch Tube
    Seals-It EAS1-05 Universal Inner Axle Seal for 2.5-2.75 Inch Tube
    (Part #9190970)
    x
                One size fits all! Fits any inner axle tube with an I.D. between 2-1/2" and 2-3/4". This eliminates ordering the wrong seal and allows you to always have the correct seal on hand. Typical applications* include Ford 9”, Quick change type rears, and 12 bolt GM. All seals are supplied with general installation guidelines. 
    • Inner Axle Seal I.D. = 7/8"
    • Axle sizes/Splines:  1-3/16” thru 1-1/2” / 28-31

     

    * Applications are reference only. Seals may be used on any rear end that is within the part number’s dimensional range. Rears can vary within a single model year and within the same model. Measure listed parameters before ordering.

  • Quick Adjustment Steel Limit Chain
    New
    Quick Adjustment Steel Limit Chain
    (Part #91045269)
    x
                

    These quick adjustable steel limit chains are designed to quickly change your chain length by simply pulling a pin, moving to the next hole and inserting the pin. You can make a chain adjustment in seconds with no tools. Made of steel with no Belleville Spring to make it IMCA approved.

    • IMCA approved
    • Quick Adjustable
    • Steel
    • Choose your tube size diameter (1-1/4", 1-3/8", 1-1/2", 1-3/4" or 2")
    • Sold Individually
  • Winters Quick Change Gears, 10 Spline
    From: $59.99
    Product Rating: 4.67 Stars
    Winters Quick Change Gears, 10 Spline
    (Part #80285)
    x
                
    • 8620 Steel
    • Heat Treated
    • CNC Machined
    • 10 spline
    • 1-1/4" Width

    Winters Quick Change Gear Chart

  • 1310 Series Chevy to Chevy U-Joint
    1310 Series Chevy to Chevy U-Joint
    (Part #91048315)
    x
                High quality, heat treated forged steel replacement U-joints. Comes with outside retaining clips.
            
  • Winters Lightweight Quick Change Rearend, 4.12 Inch Ring and Pinion
    Winters Lightweight Quick Change Rearend, 4.12 Inch Ring and Pinion
    (Part #8025069)
    x
                

    This lighter weight quick change comes with many friction reducing options. It has steel 3" tubes with Grand National ends.

    • 4.12" ring and pinion
    • 31-spline ultra-light aluminum spool
    • Spring center magnesium case
    • Thermal coated
    • 6-rib side bells
    • Steel 3" tubes with Grand National ends
    • Low drag seals
    • Big bearing rear cover with retainer

    Complete Rear-ends come with:

    • Bare listed above
    • Winters platinum Grand National hubs, bearings and seals
    • Aluminum drive plates
    • 31-spline gun drilled axle
    • .810" brake rotors
  • Wide 5 Hub Seal
    $5.99
    Wide 5 Hub Seal
    (Part #912S23756)
    x
                
            

Filter

"Oval Track, Driveline and Axles" Page 1 of 27

Page 1 of 27

  • Dana Spicer 5-1350X Heavy Duty Cross U-Joint, 1350 Series, Non-Greaseable
    Dana Spicer 5-1350X Heavy Duty Cross U-Joint, 1350 Series, Non-Greaseable
    (Part #910451350)
    x
                

    Premium Spicer Life Series® u-joints excel in performance and life. The journal crosses are cold-formed from high quality steel for maximum strength. Non-Greasable u-joints have Ample grease reservoirs in each trunion to assure effective lubrication and are pre-filled with high quality synthetic lithium grease providing superior friction reduction and higher temperature resistance. Spicer Life Series® u-joints use Spicer's highest quality, triple-lip seal along with an external seal guard to resist the harshest conditions. So when you replace your car or truck universal joints with genuine Spicer technology, you can rest assured that you are helping to ensure the maximum life for your vehicle.

    Non-Greasable u-joints are stronger than greaseable units since they don't have any grease passages in them.

    • Heavy Duty U-joint
    • 1350 Series
    • 3.625 x 1.188
    • Non-Greaseable cross shaft


  • Dana Spicer 5-3615X U-Joint w/Coated Caps for Alum Driveshaft, 1350 Series
    Dana Spicer 5-3615X U-Joint w/Coated Caps for Alum Driveshaft, 1350 Series
    (Part #910453615)
    x
                

    Premium Spicer Life Series® u-joints excel in performance and life. The journal crosses are cold-formed from high quality steel for maximum strength. Non-Greasable u-joints have Ample grease reservoirs in each trunion to assure effective lubrication and are pre-filled with high quality synthetic lithium grease providing superior friction reduction and higher temperature resistance. Spicer Life Series® u-joints use Spicer's highest quality, triple-lip seal along with an external seal guard to resist the harshest conditions. So when you replace your car or truck universal joints with genuine Spicer technology, you can rest assured that you are helping to ensure the maximum life for your vehicle.

    Non-Greasable u-joints are stronger than greaseable units since they don't have any grease passages in them.

    • Coated Caps
    • 1350 Series
    • 3.625 x 1.188 
    • For use with Aluminum drive shafts
    • Non-Greaseable cross shaft


  • Axle Housing Inner Seal, 9 Inch Ford Grand National/Quick Change Rearends
    Axle Housing Inner Seal, 9 Inch Ford Grand National/Quick Change Rearends
    (Part #9190951)
    x
                

    High cornering forces can force the gear lube out of the center section and down the axle tube leaving the ring and pinion high and dry! This billet aluminum seal has three O-rings that seal it to the axle tube and two bonded, heavy duty, neoprene inner seals designed to compensate for any amount of axle shaft runout. Keeps gear oil in the center section. These seals will take up to an 1.5” diameter axle.

    • Anodized billet aluminum
    • A must for cambered rear ends
    • For 9" Ford Grand National and Quick Change type housings
    • For up to 1.5” diameter axle
    • Keeps gear oil in the center section
    • Outside Diameter: 2.56"
    • Overall Length: 1.50"
    • This seal will fit our steel wide 5 axle
    • Choose housing tube I.D. size needed:
      • 2.500" - Gold
      • 2.562" - Blue
      • 2.625" - Red
      • 2.750" - Silver

    919-0951 Instructions (PDF)

  • Winters Side Bell 6 Rib
    From: $244.99
    Winters Side Bell 6 Rib
    (Part #802K1663)
    x
                

    Winters Replacement Parts

    Speedway Motors has everyting you need to repair or upgrade your Winters quick change rearend. From center sections and gear sets to bearings, washers and O-Rings, we can help you get your rear back on the track!

    Winters Replacement Parts Figure (pdf)

  • Winters Performance 6746 Quick Change Standard Rear Cover
    Winters Performance 6746 Quick Change Standard Rear Cover
    (Part #8026746)
    x
                
    • Standard rear cover
    • Complete with bearings
  • Winters Performance 7309 Bearing Cone, Steel Spools/Differentials
    Winters Performance 7309 Bearing Cone, Steel Spools/Differentials
    (Part #8027309)
    x
                

    Winters Replacement Parts

    Speedway Motors has everyting you need to repair or upgrade your Winters quick change rearend. From center sections and gear sets to bearings, washers and O-Rings, we can help you get your rear back on the track!

    Winters Replacement Parts Figure (pdf)

  • 9 Inch Ford Housing with Metric Brackets, 60-3/4 Inch Hub-to-Hub Width
    9 Inch Ford Housing with Metric Brackets, 60-3/4 Inch Hub-to-Hub Width
    (Part #91048375)
    x
                If your class does not allow a grand national rear end this is your best choice. These housings have new centerless ground 3" tubes installed in reclaimed original Ford 9" housings and have the end and metric brackets jig welded in place. We offer this housing with either centered or 2" offset yoke to the right pinion locations. Works great with Currie cut-to-fit axles. Axles sold separately. Use two 30 inch axles. IMCA Approved.
            
  • Bearing-Seal Kit for Two Mustang II Brake Rotors
    Bearing-Seal Kit for Two Mustang II Brake Rotors
    (Part #91031000)
    x
                

    This bearing and seal kit includes two inner wheel bearings, two outer wheel bearings and two inner grease seals. This kit is enough for two brake rotors and is intended to be used with a new rotor installation as this kit does not include the bearing races or cups.

    If your project willl be making use of used rotors, you will require new bearing races or cups.  Therefore you will need to purchase the bearing and seal kit # 910-31052 suggested below in place of kit # 910-31000.

    Works with Mustang II/Pinto and Granada rotors using Mustang II/Pinto spindles only. It will not work for installing Mustang II/Pinto brake rotors on 1949-1954 Chevy spindles. Not for use with early Chevy spindle brake conversion kits.

    -Large Bearing-
    Thickness: .656"
    Upper OD: 1.900"
    Lower OD: 2.150"
    Bearing ID: 1.375"

    -Small Bearing-
    Thickness: .651"
    Upper OD: 1.380"
    Lower OD: 1.570"
    Bearing ID: 0.864"

    Never install new hubs with old bearings.

  • AFCO 10350 Standard Wide 5 Hub Bearing Kit W/ STD Nuts
    AFCO 10350 Standard Wide 5 Hub Bearing Kit W/ STD Nuts
    (Part #10610350)
    x
                Kit fits all wide 5 hubs except early Howe.
            
  • Ford 9 Inch Megalite Steel Full Spool, 28-Spline
    Ford 9 Inch Megalite Steel Full Spool, 28-Spline
    (Part #91048611)
    x
                These Ford 9" megalite steel full spools weigh just 5.55 lbs.

    Comparison spool weights:

    • Aluminum - 5.0 lbs.
    • Lite Steel - 6.0 lbs.
    • Standard Steel - 8.9 lbs.
    • Stock carrier with mini spool - 13.7 lbs.

    Note: All Ford 9" full spools use overhaul kit 9190950-31, even if they are a 28-spline spool. The 9190950-31 contains the large I.D. standard O.D. carrier bearings and pinion bearings needed for use with our full spools.

    If you are using the H.D. nodular iron center section which uses the large diameter carrier bearings, order kit 9190950-31s, which also includes the large pinion bearings for use with the Daytona pinion support.

  • 9 Inch Ford Viton Pinion Seal
    9 Inch Ford Viton Pinion Seal
    (Part #912S18833V)
    x
                

    These Viton 9" Ford rear axle pinion seals are good to over 400° F. Stock rubber seal starts to deteriorate at about 250° F.

  • Grand National Rear Hub Bolts, Pair
    Grand National Rear Hub Bolts, Pair
    (Part #91048385-2)
    x
                

    Pair of Grand National rear end drive flange screws.

    • flathead Allen screws
    • 5/16"-18 x 3/4"
    • 1/2" thread length
    • black oxide coated steel
  • Winters Performance 7439 007 Front Cap O-Ring
    Winters Performance 7439 007 Front Cap O-Ring
    (Part #8027439)
    x
                Wide 5 hub replacement parts.
            
  • Dana Spicer 5-3614X U-Joint w/Coated Caps for Alum Driveshaft, 1330 Series
    Dana Spicer 5-3614X U-Joint w/Coated Caps for Alum Driveshaft, 1330 Series
    (Part #910453614)
    x
                

    Premium Spicer Life Series® u-joints excel in performance and life. The journal crosses are cold-formed from high quality steel for maximum strength. Non-Greasable u-joints have Ample grease reservoirs in each trunion to assure effective lubrication and are pre-filled with high quality synthetic lithium grease providing superior friction reduction and higher temperature resistance. Spicer Life Series® u-joints use Spicer's highest quality, triple-lip seal along with an external seal guard to resist the harshest conditions. So when you replace your car or truck universal joints with genuine Spicer technology, you can rest assured that you are helping to ensure the maximum life for your vehicle.

    Non-Greasable u-joints are stronger than greaseable units since they don't have any grease passages in them.

    • Coated Caps
    • 1330 Series
    • 3.625 x 1.062 
    • For use with Aluminum drive shafts
    • Non-Greaseable cross shaft


  • GM 10 Bolt Ring and Pinion Instal Kit, 8.5 R&P, 30 Spline
    GM 10 Bolt Ring and Pinion Instal Kit, 8.5 R&P, 30 Spline
    (Part #919831021)
    x
                Everything you need for a complete ring and pinion installation job. 

    Kit Includes:

    • cover gasket
    • crush sleeve
    • marking compound and brush
    • pinion and carrier bearings
    • pinion nut and washer
    • pinion seal
    • thread locking compound
    • sealer

    Note: Pinion-depth shims are not included. 

  • Winters Performance 7403T Pro-Eliminator O-Ring, 4 and 6 Rib Bell
    Winters Performance 7403T Pro-Eliminator O-Ring, 4 and 6 Rib Bell
    (Part #8027403T)
    x
                

    Pro-Eliminator Rearend and Winters Replacement Parts

    Speedway Motors has everyting you need to repair or upgrade your Winters quick change rearend. From center sections and gear sets to bearings, washers and O-Rings, we can help you get your rear back on the track!

    • Winters O-Ring, 4 and 6 Rib Bell

    Winters Replacement Parts Figure (pdf)

    Pro Eliminator Rear End Diagram (GIF) 

  • MPD 13634 Sprint Racing Low Drag Bearing Assembly, REM Finish
    MPD 13634 Sprint Racing Low Drag Bearing Assembly, REM Finish
    (Part #54613634)
    x
                These bearing sets fit all Sprint car front hubs using light weight spindles & all midget hubs.

    Testing shows a good quality tapered wheel bearing provides the lowest rolling resistance when a thrust (side) load is applied, compared to all the popular bearing options. Sprint Cars & Midgets are in constant thrust load. MPD takes quality USA made Timken® bearings and REM® Finish for the ultimate low drag race bearing set.

    MPD recommends NEW Bearing Spacers & TFE Low Drag Seals to be used with these REM® Finished Timken® Tapered Roller bearings. Once adjusted for your hub. You simply lock down your spindle nut for a perfect set of Freewheeling Bearings.

    Use an injection needle to selectively fill the bearing with grease only between the rollers, eliminating overpacking and the resultant overheating that occurs. Properly packed bearings will run cooler, have less rolling resistance and may be packed less often.
    • Provides the lowest rolling resistance when a thrust (side) load is applied
    • Includes Timken bearings and REM finish for the ultimate low drag race bearing set
    • Use in conjunction with the MPD bearing spacer (546013607) and TFE low drag seal (546025605)
  • DRP 10503 Adjustable Wide 5 Axle Shaft Wheel Bearing Spacer
    DRP 10503 Adjustable Wide 5 Axle Shaft Wheel Bearing Spacer
    (Part #91010503)
    x
                

    These adjustable wheel bearing spacers are easy to install.  They allow you to set the bearing pre-load, preventing over tightening while reducing drag.

    • Anodized aluminum
    • Adjustable
    • Easy installation
    • Set pre-load and reduce drag
    • Sold each
  • Low Friction 28mm Double Row Birdcage Bearing
    Low Friction 28mm Double Row Birdcage Bearing
    (Part #94059142)
    x
                

    These low friction 28mm Bird Cage bearings are 1.1" wide with a  3.940" OD.

    • Low friction 28mm double row
    • 1.1" wide, 3.940"outside diameter
    • Fits many different bird cages
  • Winters Performance POSTER-10 10-Spline Quick Change Gear Chart
    Winters Performance POSTER-10 10-Spline Quick Change Gear Chart
    (Part #8021000)
    x
                Perfect for trailers or the race shop!  19" x 25"  Laminated.
            
Goto Previous PagePrevious Page
1 2 3 4 5 ... 27