Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Open Wheel Driveline & Rear End At Speedway Motors

Speedway Motors can help you put the power to the wheels with a complete selection of Sprint and Midget driveline components. We stock fully-loaded quick change rearend assemblies, plus all the differential gears and parts to service them. Quality open wheel components from a reliable source, Speedway Motors.

"Open Wheel, Midget" Page 1 of 2

  • B&J Midget Quick Change Gears
    From: $189.99
    B&J Midget Quick Change Gears
    x
                

    These are the lightest and strongest gears available!  Each gear is hand finished and inspected for superior quality.  Gears are 1" wide and made for 6-spline rearends.  Please use the chart below to determine which set(s) you need!

    B & J Quick Change Chart

  • Winters Performance 7297V D-Mount Front Hub Seal
    Winters Performance 7297V D-Mount Front Hub Seal
    x
                Single lip grease seal for Winters direct mount front hubs.
            
  • Sprint Taper Hub Outer Bearing, Small
    Sprint Taper Hub Outer Bearing, Small
    x
                Fits tapered-bearing hubs and Weld hubs. Works with stepped shaft spindles. If you have straight shaft, you will need two outer bearings.
            
  • Winters D-Mount Aluminum Front Hubs, RH/LH Rotor Mounts
    Winters D-Mount Aluminum Front Hubs, RH/LH Rotor Mounts
    x
                

    Winters direct mount front hubs are forged 2024-T3 aluminum for superior strength, durability and weight savings. Hubs are then CNC machined to precise tolerances. Gold anodized to resist corrosion.

    Kit includes bearings, seals, wheel studs, nuts, LH hub w/brake mount, RH hub w/ brake mount, and billet threaded hubcaps.

  • MPD 13634 Sprint Racing Low Drag Bearing Assembly, REM Finish
    MPD 13634 Sprint Racing Low Drag Bearing Assembly, REM Finish
    x
                These bearing sets fit all Sprint car front hubs using light weight spindles & all midget hubs.

    Testing shows a good quality tapered wheel bearing provides the lowest rolling resistance when a thrust (side) load is applied, compared to all the popular bearing options. Sprint Cars & Midgets are in constant thrust load. MPD takes quality USA made Timken® bearings and REM® Finish for the ultimate low drag race bearing set.

    MPD recommends NEW Bearing Spacers & TFE Low Drag Seals to be used with these REM® Finished Timken® Tapered Roller bearings. Once adjusted for your hub. You simply lock down your spindle nut for a perfect set of Freewheeling Bearings.

    Use an injection needle to selectively fill the bearing with grease only between the rollers, eliminating overpacking and the resultant overheating that occurs. Properly packed bearings will run cooler, have less rolling resistance and may be packed less often.
    • Provides the lowest rolling resistance when a thrust (side) load is applied
    • Includes Timken bearings and REM finish for the ultimate low drag race bearing set
    • Use in conjunction with the MPD bearing spacer (546013607) and TFE low drag seal (546025605)
  • Winters Performance 6781 Pro-Eliminator Midget Sliding Coupler
    Winters Performance 6781 Pro-Eliminator Midget Sliding Coupler
    x
                

    These Pro-Eliminator rear end replacement parts are in stock and ready to order.

    Pro Eliminator Rear End Part Guide (Link)

  • Sander Engineering S333-26.5 Midget Torque Tube and Collar
    Sander Engineering S333-26.5 Midget Torque Tube and Collar
    x
                

    This Sander Engineering midget torque tube and collar will fit most Midget Rear ends. 

     

  • MPD Racing 063805 U-Joint, Esslinger Engine
    MPD Racing 063805 U-Joint, Esslinger Engine
    x
                

    MPD Racing Aluminum u-joint machined from 7075 aluminum. Will work with only Midget Sprint Cars

    • 16 Spline
    • Lightweight
  • Weld 13/15 Magnum Hub With Rotor Mount
    Weld 13/15 Magnum Hub With Rotor Mount
    x
                
    • 100% CNC machined anodize black aluminum
    • Designed for use with a sprint or midget
    • Accommodates a straight shaft spindle and brake rotor
  • Winters Performance 3700 Billet Aluminum U-Joint
    Winters Performance 3700 Billet Aluminum U-Joint
    x
                

    Winters billet aluminum U-joint machined from 7076-T6 aluminum. Kit includes our U-joint spring 624-S306.

  • Weld Racing Ultra Hub
    $250.99
    Weld Racing Ultra Hub
    x
                

    Sprint hubs will never be the same. The new Weld Racing 3 Spoke Ultra Hub makes all other hubs obsolete. The innovative 3 spoke design reduces static weight by over 30%, and more importantly reduces the rotational moment of inertia by over 61%. Available for 10", 13" and 15" applications. 

    These aluminum hubs are 'for dirt use only'. They include bearings, seals and dust cap. Specify LH or RH. 

  • Winters Performance 6778A 44/3 Midget 44 Inch Replacement Axle
    Winters Performance 6778A 44/3 Midget 44 Inch Replacement Axle
    x
                

    Speedway offers a Winters Midget 44" aluminum replacement axle. With 3" offset and 31" spline. 


Goto Previous PagePrevious Page
1 2