Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products

Speedway Motors has hundreds of fuel and oil line fittings in stock and ready to ship! Plumb your open wheel race car with the same hose and fittings the big-name professional racers use like Jiffy-Tite and Fragola. We stock everything from anodized AN fittings to high-pressure stainless steel braided line.

Featured Products
Straight Socketless Reuseable Push-On Hose End for -4 AN Fitting
Straight Socketless Reuseable Push-On Hose End for -4 AN Fitting
x
            

Push-on straight brass hose ends for use with AN fittings. Special construction assures a tight, leak-proof connection with maximum operating pressures up to 350 psi. Covers a wide variety of automotive fluid conveying applications, including air, water, gasoline, and fuel and lubricating oils.

Socketless Push-On Application Chart (GIF)

Socketless Push-On Assembly (GIF)

Fitting Thread Size Guide (GIF)

NPT Thread Size Chart (GIF)

90 Degree Flare Adaptor, AN6 to 1/8 Inch NPT
90 Degree Flare Adaptor, AN6 to 1/8 Inch NPT
x
            

Pipe to 90° flare adaptor. 37° AN. 

Fitting Thread Application Chart (GIF)

Quick Tight Hose Clamp, 1-5/8 - 2-1/8 Inch
Quick Tight Hose Clamp, 1-5/8 - 2-1/8 Inch
x
            Stainless steel quick-tight tube clamps eliminate the need for a screwdriver. Has hole for safety wire tie. Clamps over 1.625" to 2.125" O.D. hose.
        
Jiffy-Tite 52412 Quick Connect Fluid Fittings, -12 AN Male Plug
Jiffy-Tite 52412 Quick Connect Fluid Fittings, -12 AN Male Plug
x
            

Tested and proven to have a 100% leak proof seal at 200 psi and 350° F. Made of aluminum, these Jiffy-Tite valved disconnects are compact, durable, and corrosion resistant. High-flow valve technology in the plug and socket assembly automatically interrupts the flow of fluid when disconnected by hand. Not intended for brake systems.

Select a socket and a plug to make a complete coupler. AN sizes are 37° for mating with existing hose ends or bungs.

See Application tab for intended use on each disconnect/plug.

Jiffy-Tite Flow Specs (Link)

"Open Wheel, Fittings and Hose" Page 1 of 3

  • Inverted Flare Thread Nuts for 3/16 Inch Tubing, 3/8-24
    Inverted Flare Thread Nuts for 3/16 Inch Tubing, 3/8-24
    x
                

    Steel 3/8"-24 IFM thread nuts for 3/16" brake line when double flared to 45°.

  • AFCO Aluminum Tube, 13 Inch Long, 1 Inch O.D. (3/4) Inch
    AFCO Aluminum Tube, 13 Inch Long, 1 Inch O.D. (3/4) Inch
    x
                

    Insist on 6061-T6 drawn tubing for strength, durability, and precise fit.  Extruded tubing looks similar, but it is not as strong or durable.  Extruded parts are prone to failure, while drawn parts keep performing.  Drawn material offers the same strength as hex without the additional weight.

    •  2-1/4” of tapped thread on each end. 

    Tech Tip:  Tube length will need to be 4" shorter than eye to eye working length.

  • Gates 32948 Power Grip Hose Clamp, 1 3/4 Inch - 2 Inch OD
    Gates 32948 Power Grip Hose Clamp, 1 3/4 Inch - 2 Inch OD
    x
                

    These heatshrink tube clamps replace your ugly old hose clamps and give a much cleaner look. Conforms to any shape of hose or housing, even out of round fittings. They are easy to install with only a heat gun. Made from a heat-sensitive thermoplastic with a memory to prevent over/under-tightening. Unique indicator tells you when clamp has shrunk to seal.

    Temperature rating: -40° F to 302° F (-40° C to 150° C)

    Instruction Sheet (PDF) 

  • Steel -6 AN Fitting for Aeroquip FC300 High Pressure Hose, 45 Degree
    Steel -6 AN Fitting for Aeroquip FC300 High Pressure Hose, 45 Degree
    x
                

    Steel power steering hose end fitting for use with Aeroquip FC300 high pressure hose. 45° elbow -6 AN swivel fitting easily assembles onto -6 AN hose with a bench vise and/or wrenches.  Steel hose ends are reusable.

    Fitting Thread Size Chart (GIF)

    FC300 Assembly Chart (GIF)

  • Snap-In Grease Needle
    $7.99
    Snap-In Grease Needle
    x
                

    Inject grease into low profile grease zerks or hard to reach places with this adapter. Nipple snaps into your existing grease gun end.

     

  • Gates 32925 Power Grip Hose Clamp, 15/16 Inch - 1 1/16 Inch OD
    Gates 32925 Power Grip Hose Clamp, 15/16 Inch - 1 1/16 Inch OD
    x
                

    These heatshrink tube clamps replace your ugly old hose clamps and give a much cleaner look. Conforms to any shape of hose or housing, even out of round fittings. They are easy to install with only a heat gun. Made from a heat-sensitive thermoplastic with a memory to prevent over/under-tightening. Unique indicator tells you when clamp has shrunk to seal.

    Temperature rating: -40° F to 302° F (-40° C to 150° C) 

    Gates Power Grip Hose Clamp, 15/16" - 1-1/16" OD

    Instruction Sheet (PDF) 

  • Blue Straight AN6 Flare Adapter to 1/4 Inch Aluminum Pipe Fitting
    Blue Straight AN6 Flare Adapter to 1/4 Inch Aluminum Pipe Fitting
    x
                

    These straight flare adaptors connect 1/4" pipe to straight -6 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fitting
    • -6 AN to 1/4" aluminum pipe
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Blue anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Gates 32954 Power Grip Hose Clamp, 2 Inch - 2 1/4 Inch OD
    Gates 32954 Power Grip Hose Clamp, 2 Inch - 2 1/4 Inch OD
    x
                

    These heatshrink tube clamps replace your ugly old hose clamps and give a much cleaner look. Conforms to any shape of hose or housing, even out of round fittings. They are easy to install with only a heat gun. Made from a heat-sensitive thermoplastic with a memory to prevent over/under-tightening. Unique indicator tells you when clamp has shrunk to seal.

    Temperature rating: -40° F to 302° F (-40° C to 150° C)

    Instruction Sheet (PDF) 

  • Jiffy-Tite 52312 Quick Connect Fluid Fittings, -12 AN Female Socket
    Jiffy-Tite 52312 Quick Connect Fluid Fittings, -12 AN Female Socket
    x
                

    Tested and proven to have a 100% leak proof seal at 200 psi and 350° F. Made of aluminum, these Jiffy-Tite valved disconnects are compact, durable, and corrosion resistant. High-flow valve technology in the plug and socket assembly automatically interrupts the flow of fluid when disconnected by hand. Not intended for brake systems.

    Select a socket and a plug to make a complete coupler. AN sizes are 37° for mating with existing hose ends or bungs.

    See Application tab for intended use on each disconnect/plug.

    Jiffy-Tite Flow Specs (Link)

  • Blue Straight AN10 Flare Adapter to 3/4 Inch Aluminum Pipe Fitting
    Blue Straight AN10 Flare Adapter to 3/4 Inch Aluminum Pipe Fitting
    x
                

    These straight flare adaptors connect 3/4" pipe to straight -10 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fitting
    • -10 AN to 3/4" aluminum pipe
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Blue anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • 90 Degree Flare Adaptor, AN4 to 1/8 Inch NPT
    90 Degree Flare Adaptor, AN4 to 1/8 Inch NPT
    x
                

    Pipe to 90° flare adaptor. 37° AN. 

    Fitting Thread Application Chart (GIF)

  • Quick Tight Hose Clamp, 1 Inch to 1-1/2 Inch
    Quick Tight Hose Clamp, 1 Inch to 1-1/2 Inch
    x
                Stainless steel quick-tight tube clamps eliminate the need for a screwdriver. Has hole for safety wire tie. Clamps over 1" to 1.50" O.D. hose.
            
  • Jiffy-Tite 52412 Quick Connect Fluid Fittings, -12 AN Male Plug
    Jiffy-Tite 52412 Quick Connect Fluid Fittings, -12 AN Male Plug
    x
                

    Tested and proven to have a 100% leak proof seal at 200 psi and 350° F. Made of aluminum, these Jiffy-Tite valved disconnects are compact, durable, and corrosion resistant. High-flow valve technology in the plug and socket assembly automatically interrupts the flow of fluid when disconnected by hand. Not intended for brake systems.

    Select a socket and a plug to make a complete coupler. AN sizes are 37° for mating with existing hose ends or bungs.

    See Application tab for intended use on each disconnect/plug.

    Jiffy-Tite Flow Specs (Link)

  • Aluminum Socketless Reusable Push-On Hose Barb Ends for AN Fittings
    Aluminum Socketless Reusable Push-On Hose Barb Ends for AN Fittings
    x
                

    These lightweight socketless fittings are machined from aluminum alloy and anodized red and blue with a luster finish, the ultimate in professional appearance. Precision machine work ensures a positive seal when coupling Full Flow™ hose ends to your carburetor. They are ideal for use as fuel line connectors or adapters.

    • AN to hose barb 
    • Choose straight, 45°, 90°, 120° or 180°. Then choose -6, -8, -10 or -12 AN size.
    • Use with Aeroquip Special Application blue hose
    • For use with 37° AN style fittings

    Socketless Fitting Application Chart (GIF)

    AN Thread Size Guide (GIF)

    Fitting Thread Size Guide (GIF)

  • Jiffy-Tite 21802 Quick Disconnect Wing Fittings, 1/8 Inch NPT, Male
    Jiffy-Tite 21802 Quick Disconnect Wing Fittings, 1/8 Inch NPT, Male
    x
                

    Tested and proven to have a 100% leak proof seal at 200 psi and 350° F. Made of aluminum, these Jiffy-Tite valved disconnects are compact, durable, and corrosion resistant. High-flow valve technology in the plug and socket assembly automatically interrupts the flow of fluid when disconnected by hand. Not intended for brake systems.

    Select a socket and a plug to make a complete coupler. AN sizes are 37° for mating with existing hose ends or bungs.

    See Application tab for intended use on each disconnect/plug.

    Jiffy-Tite Flow Specs (Link)

  • Billet Nose Wing Post Tube Clamp, 1.250 Inch Tube
    Billet Nose Wing Post Tube Clamp, 1.250 Inch Tube
    x
                Machined to be aerodynamic - these tube clamps fit on your front torsion tubes for quick and easy adjustments or replacement.  Accept a 3/4" post, includes hardware. 
            
Goto Previous PagePrevious Page
1 2 3