Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 22

Products

Fasteners and Hardware

Shop Open Wheel Fasteners & Hardware At Speedway Motors

Speedway Motors is the sprint or midget racer's connection for high performance fasteners! Speedway can supply all your fastener needs, from nylock nuts and washers to rivets and complete Sprint car bolt kits featuring Speedway's exclusive Tru-Lite titanium bolts. Don't lose the open wheel race due to cheap fasteners! Use only the best from Speedway Motors.

Featured Products
  • Seals It Single Grommet Seal, Rubber
    Seals It Single Grommet Seal, Rubber
    (Part #9101003)
    x
                

    Grommet seals have many applications. In race cars they serve to keep unwanted smoke and fumes from entering the driver's area while protecting lines from chafing and abrading on rough surfaces. In hot rods and custom car applications, they provide the perfect "finishing touch" to all through panel installations. Wiring, fuel and oil lines, air and liquid hoses, and all other lines that make up your rod or custom, can make an otherwise detailed installation look unfinished. Seals-It grommet seals add the well-organized, professional appearance you want throughout your vehicle.

    • Choose from hose size fittment (dimension C) -AN4, -AN6, -AN8

    Other Applications Include:

    • Marine
    • Commercial Equipment
    • Motor Homes, etc. 

    Installation Notes:

    • Use of lubricant is desirable during assembly (petroleum, jelly, silicon, etc.)
    • For special hose sizes or other parts (wire looms, shafts, etc.):
      • Measure the O.D. of part in the area that will be retained by the grommet after installation.
      • Satisfactory results are obtained by punching a hole that is 1/16" (1.5mm) to 1/8" (3.2mm) less than the hose size.
    • These are general guidelines for application of grommet seals. The elastic properties of the grommets allow for wide variences based on application requirements and mounting area.
    • Holes are best put in blank grommets using "gasket" or "leather working" punches using a hardwood backing for support.
    • A sharpened piece of tubing of the desired diameter also works well; drilling is NOT recommended.
    • Split grommet seals - These do not have the same "alastic" properties due to their construction.  The hole size used should be matched closely to the item passing through the grommet. (i.e. .750" diameter shaft = .750" diameter hole)

    Grommet Seal Sizing Chart (GIF)

  • Cold Fire Super Systems 20000820 Cylinder to Valve O-Ring
    Cold Fire Super Systems 20000820 Cylinder to Valve O-Ring
    (Part #48675092)
    x
                Replacement O-ring for Cold Fire Suppression Systems.
            
  • Zip Tie Wraps, 14 Inches
    $8.99
    Product Rating: 3.50 Stars
    Zip Tie Wraps, 14 Inches
    (Part #910045)
    x
                Zip ties available in black, blue, red, white, yellow, orange, or purple.  Package of 100.
            
  • Kinsler Fuel Injection 3117 Fuel Line Bypass Pill Holder O-Ring Kit
    Kinsler Fuel Injection 3117 Fuel Line Bypass Pill Holder O-Ring Kit
    (Part #4733117)
    x
                

    Replacement set of O-rings for Kinsler bypass pill holder 3112. Includes (1) small O-ring and (1) large O-ring. Compatible with both gas and methanol.

  • Tru Rivets, 3/16 Inch Large Head
    From: $9.99
    Product Rating: 4.53 Stars
    Tru Rivets, 3/16 Inch Large Head
    (Part #91004)
    x
                Large head 3/16" aluminum pop rivets with steel shank. 1/4" to 3/8" grip range. Available in red, white, pepsi (light) blue, chevron blue, yellow, black, and orange. Box of 250.
            
  • Painless 70959 3/4 Inch ClassicBraid Wire Sleeving, 6 Feet
    Painless 70959 3/4 Inch ClassicBraid Wire Sleeving, 6 Feet
    (Part #91070959)
    x
                

    This 3/4" ClassicBraid from Painless Performance has a smooth new look that will transform your engine and give you that factory installed look. Its woven construction gives you excellent blockage against mud and dirt while giving you adequate drainage for optimum wiring protection.

    • Made in the USA
    • Continuous Temperature Rating -94° to 257°F
    • Melting Point 482°F
    • Resistant to Automotive Chemicals & Fluids
    • Great For Auto, Marine, RV, Aircraft, Power Sports, & More
    • 6' Long
  • Swedged Aluminum Throttle Linkage Tubes, 3/16 Inch (10-32) Thread
    Swedged Aluminum Throttle Linkage Tubes, 3/16 Inch (10-32) Thread
    (Part #94055301)
    x
                

    This swedged throttle linkage tubing is tapped 3/16" (10-32) LH and RH thread. One end of the throttle rod will have left hand threads, and the other end will have right hand threads. Made of 5/16" x 0.049 round aluminum tubing.

    Note: When measuring for your tube length, you will want to allow 1.5" in length for the rod ends (3/4" of length for each end when calculating your eye-to-eye measurement. For instance, an eye-to-eye length of 11.5" would require a 10" swedged tube.

  • Cold Fire Super Systems 20000800 Valve Cap O-Ring
    Cold Fire Super Systems 20000800 Valve Cap O-Ring
    (Part #48675093)
    x
                Replacement O-ring for Cold Fire Suppression Systems.
            

Filter

"Open Wheel, Fasteners and Hardware" Page 1 of 22

Page 1 of 22

  • Speed Fast Aluminum SAE/Fine Lock Nut Kit
    Speed Fast Aluminum SAE/Fine Lock Nut Kit
    (Part #94004006)
    x
                This Aluminum Nylock Nut Kit contains 50 pieces. A variation of the nyloc nut, this features a fiber and nylon locking insert for the tightest hold. Nylocs are  designed to increase locking force and prevent the nut from coming  loose. 

    Several sizes of nylocks are available in this kit for your application. Comes with (10) 10-32, (10) 5/16"-24, (10) 3/8"-24, (10) 1/4"-28,  (10) 1/2"-20.
  • Zip Tie Wraps, Stainless Steel Tooth, Black, 100 per Bag
    Zip Tie Wraps, Stainless Steel Tooth, Black, 100 per Bag
    (Part #940048)
    x
                

    These zip ties are made in the U.S.A. and feature a stainless steel securing tooth. They come 100 to a package and are perfect for securing loose wiring and hoses or can help serve as temporary fixes to many odd jobs and projects.

    • Stainless Tooth Tie Wraps feature super strong self-locking, stainless steel tooth, one piece design, standard size head.
    • Black Tie Wraps are UV resistant. Recommended for outdoor usage.
    • Metal Detectable
    • Temperature Ratings 185 F / 85 C.
    • UL Flame Rating 94V-2.
    • Minimum installation temperature is greater than 32 F or 0 C.
    • Made From Nylon 6/6.
    • Choose from lengths of 4", 5.5", 7.3", and 11.4"
    • 100 per Bag
  • AFCO 10138 Steel Jam Nut, 3/8-24 RH
    $0.78
    $0.99
    AFCO 10138 Steel Jam Nut, 3/8-24 RH
    (Part #10610138)
    x
                

    Steel fine thread jam nuts for use with rod ends, heim joints, and clevis.

  • Speed Fast O-Ring Assortment Kit
    Speed Fast O-Ring Assortment Kit
    (Part #94004112)
    x
                
    • Wide selection of popular O-rings
    • 1/16" in. section to 1/4" in. O.D.
    • 1/8" in. section to 2-1/4" in. O.D.
    • R-01 thru R-32
    • 407 pieces
    •  Nitrile Rubber, Buna-N SAE Assortment
    • Suitable for many Hydrocarbons, Fats, Oils, Gas, etc...
    • Not Suitable for use with Brake Fluids
    • Good Abrasion Resistance and Resistant to Compression
    • High Tensile Strength
  • Mag Daddy 3/4 Inch Medium Cable Daddy Magnetic Wire Fasteners, 5-Pack
    Mag Daddy 3/4 Inch Medium Cable Daddy Magnetic Wire Fasteners, 5-Pack
    (Part #91033243)
    x
                These medium Mag Daddy™ fasteners are designed to hold up to 10  unshielded Cat 5 Cables.  Rated at 16 lbs., these black fasteners  feature a magnetic bond for easy installation and removal without the  use of screws, wires, or zip-ties.
    • Easy Installation
    • Plastic lasts 20x longer than Nylon 6.6
    • Rotates 360°
    • Reusable
    • Take wires in and out
    • Sold in sets of 5 

    Suggested locations for use: Steel, Beams, Purlins, Ceiling Decks, Drop Ceiling Channels, Metal Joists, Frame Rail, Screw Heads, Metal Washer, etc.

    91033243 Cable Daddy Information/Instructions (PDF) 

  • Steel 3/8 Inch AN6 Washers, 50 Pack
    Steel 3/8 Inch AN6 Washers, 50 Pack
    (Part #94004060)
    x
                Steel 3/8" AN Washers, 50 Pack
            
  • Pop Rivet 151 Piece Kit
    $15.99
    Pop Rivet 151 Piece Kit
    (Part #94004007)
    x
                151 piece kit comes with 1/8" and 3/16" pop rivets with steel head and steel mandrel, and aluminum head with steel mandrel. Or aluminum head with aluminum mandrel. 

    Also comes with an assortment of backing washers as well as the large headed 3/16" style. All packed into a convenient storage case.

  • AFCO 10141 Steel Jam Nut, 3/4-16 LH
    $1.35
    $1.99
    AFCO 10141 Steel Jam Nut, 3/4-16 LH
    (Part #10610141)
    x
                

    Steel fine thread jam nuts for use with rod ends, heim joints, and clevis.

  • Speed Fast Stainless Safety Wire, .032 Inch
    Speed Fast Stainless Safety Wire, .032 Inch
    (Part #91089407)
    x
                Speed Fast 304 stainless steel safety wire. Sold in one pound rolls and comes with a handy belt clip.
            
  • TI64 222 Titanium Micro Sprint Bullet Nose Stop Adjuster Bolt Kit
    TI64 222 Titanium Micro Sprint Bullet Nose Stop Adjuster Bolt Kit
    (Part #940222)
    x
                These bullet nose stop adjusters for Micro Sprint cars are constructed of titanium for long lasting durability.  They come in a set of 4 bolts with 5/16"-18 x 1-3/4" threads.
    • Bullet Nose Stop Adjuster
    • Set of 4
    • 5/16"-18 x 1-3/4"
  • Mag Daddy 1/2 In Large Cable Daddy Magnetic Wire/Cable Fasteners
    Mag Daddy 1/2 In Large Cable Daddy Magnetic Wire/Cable Fasteners
    (Part #91062423)
    x
                Mag Daddy Cable-Daddy™ fasteners are designed to  easily secure all wires and cables in a variety of environments. These  magnetic fasteners adhere to most all metal surfaces with an absurd 23  lbs. of retention force! Mag Daddy Cable-Daddy™ fasteners are the best  solution to wire and cable management. They're offered in a choice of  three sizes to meet your requirements. Whether you need to hold a brake  line in place or quickly organize wires or cables, Mad Daddy Cable-Daddy™  fasteners are the perfect fix.
    • Black rectangular cable hold-down
    • 23 lbs. of retention force
    • Magnet base is 26mm x 11mm with a total height of 18.5mm
    • Holds up to 20 unshielded Cat 5 Cables
    • Easy Installation
    • Plastic lasts 20x longer than Nylon 6.6
    • Ability to Rotate 360°
    • Re-usability
    • Take in and out wires
    • Sold in packs of 5

    Locations: Steel, Beams, Purlins, Ceiling Decks, Drop Ceiling Channels, Metal Joists, Frame Rail, Screw Heads, Metal Washer, etc.

    91062423 Cable Daddy Information/Instructions (PDF)

  • Plastic Large Head Quarter Turn Fasteners, .500 Inch Grip, Pack/10
    Plastic Large Head Quarter Turn Fasteners, .500 Inch Grip, Pack/10
    (Part #91007137)
    x
                
    1/4 turn panel fasteners that have an extra large 1-1/8" diameter head with a 1/2" grip. These quarter turn fasteners are available in black, blue, grey, purple, red, white and yellow.
    • Extra large 1-1/8" diameter head
    • .500" grip
    • Available in Black, Blue, Grey, Purple, Red, White, or Yellow
    • Pack of 10

    Measurement Guide (Link)

  • Painless 70956 1/8 Inch ClassicBraid Wire Sleeving, 20 Feet
    Painless 70956 1/8 Inch ClassicBraid Wire Sleeving, 20 Feet
    (Part #91070956)
    x
                

    This ClassicBraid has a smooth texture and appearance that will transform your engine bay and give you that factory installed look. Its tight woven construction gives you an excellent blockade against mud and dirt while keeping adequate drainage for optimum wiring protection. 

    • Made in the USA
    • Continuous Temperature Rating -94° to 257°F
    • Melting Point 482°F
    • Resistant to Automotive Chemicals & Fluids
    • Great For Auto, Marine, RV, Aircraft, Power Sports, & More
    • 20' long
  • DMI RRC-1620 XR-1 Bulldog Rearend Stub Shaft Snap Ring
    DMI RRC-1620 XR-1 Bulldog Rearend Stub Shaft Snap Ring
    (Part #9409046)
    x
                

    Manufactured with the highest quality castings, bearings, and gears these rearend parts have proven reliability.

    Stub Shaft Snap Ring

  • Tru-Lite Titanium Torque Tube Stud, 3/8 Inch-16-24 x 1.25
    Tru-Lite Titanium Torque Tube Stud, 3/8 Inch-16-24 x 1.25
    (Part #9406053)
    x
                

    These titanium studs are fine on one end and coarse on the other.

    • 3/8" x 1.25.
    • Titanium standard.

     

  • Tru-Lite Fine Thread Titanium Bolt, 3/8-24 x 1.500 Inch
    Tru-Lite Fine Thread Titanium Bolt, 3/8-24 x 1.500 Inch
    (Part #9406303)
    x
                

    3/8"-24 with 9/16" Hex Head

    These fine thread titanium bolts feature heat treated rolled threads. Titanium bolts have a greater tensile strength than Grade 8 bolts at half the weight.

  • Tru-Lite Titanium Bolt, 1/2-20 Fine Thread, 1.400 In Long, 3/4 In
    Tru-Lite Titanium Bolt, 1/2-20 Fine Thread, 1.400 In Long, 3/4 In
    (Part #9405814)
    x
                

    These fine thread Tru-Lite titanium bolts feature heat treated rolled threads. Titanium bolts have a greater tensile strength than Grade 8 bolts at half the weight. Made from 6AL/4V material which has 3 times the strength of aluminum and is 42% lighter than steel.

    • Fine thread Titanium
    • Greater tensile strength than Grade 8 bolts
    • 3 times the strength of aluminum
    • 42% lighter than steel
    • 1/2"-20 x 1.400"
    • 3/4" Hex Head
    • Application: radius rod to birdcage
  • Small Diameter Steel Jam Nuts, 5/8-18, Pack/6
    Small Diameter Steel Jam Nuts, 5/8-18, Pack/6
    (Part #1756048)
    x
                Steel fine thread jam nuts for use with rod ends, heim joints, and clevis. Each has a small 3/4" O.D. for added clearance. Sold in bags of six nuts. Available with left or right thread.
            
  • DMI RRC-1110 XR-1 Bulldog Rearend Side Bell Stud
    DMI RRC-1110 XR-1 Bulldog Rearend Side Bell Stud
    (Part #9409019)
    x
                

    Manufactured with the highest quality castings, bearings, and gears these rearend parts have proven reliability.

    Side Bell Stud

  • AFCO 80745 Twister Pliers
    $49.99
    $50.99
    AFCO 80745 Twister Pliers
    (Part #10680745)
    x
                
    • Utilizes end bearing for faster, smoother twisting
    • Great for use in small areas where a second pull is required
Goto Previous PagePrevious Page
1 2 3 4 5 ... 22