Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 7

Products

HVAC

Shop Muscle Car Heating & A/C At Speedway Motors

Speedway Motors has the heating and air conditioner you need to make your muscle car comfortable again. We offer great prices on new heater cores, sound proof insulation mats and air conditioning kits. Keep your car cool in the summer heat with quality A/C components from Speedway Motors.

Featured Products
  • AC O Rings - Replacement AN10 AC O-Rings - Set of 6
    AC O Rings - Replacement AN10 AC O-Rings - Set of 6
    (Part #6173418)
    x
                Replacement o-rings for your air conditioning system. 
            
  • 90 Degree Nickel Plated AC Fitting, -6 AN
    90 Degree Nickel Plated AC Fitting, -6 AN
    (Part #6171732)
    x
                These handsome nickle plated steel fittings are reuseable.
            
  • Air Conditioning Condenser, 12 x 19-1/2 Inch
    Air Conditioning Condenser, 12 x 19-1/2 Inch
    (Part #42815215)
    x
                

    Horizontal mount aluminum A/C condenser with parallel flow. This is 12" wide by 19-5/8" tall with fittings on passenger/right hand side. Top fitting is 90 degree pointed down and lower fitting is straight point out horizontal.

    Has one -6 AN and one -8 AN fitting.

  • A/C Hose Kit
    $89.99
    Product Rating: 5.00 Stars
    A/C Hose Kit
    (Part #42810100)
    x
                

    These air conditioning hose kits include enough hose and fittings to allow a normal installation in applications without bulkhead fittings. 

    • (2) Band Clamps
    • (4) AN6 Straight
    • (1) AN8 Straight
    • (1) AN10 Straight
    • (2) AN6 90 Degree
    • (1) AN8 90 Degree
    • (1) AN10 90 Degree
    • (1) AN8 90 Degree with Service Port
    • (1) AN10 90 Degree with Service Port
    • (4) #6 O-Rings
    • (2) #8 O-Rings
    • (2) #10 O-Rings
    • (2) Grommets
    • 6 ft #6 Hose
    • 5 ft #8 Hose
    • 4 ft #10 Hose

     

    Fittings will need to be crimped at your local shop.

  • Slim Line Heat/Air Unit
    $359.99
    Product Rating: 5.00 Stars
    Slim Line Heat/Air Unit
    (Part #91000466)
    x
                This low profile under the dash mount heat/cool unit is 26.25" wide 5.25" tall and 12" deep. Features a three speed blower, heat/cool adjustment, defroster duct hook-ups, and three 1" x 5" front adjusting vents. Easy to install with mounting slots on the sides of the unit all plumbing and wiring done from the back side of the unit. Will handle 18,000 BTU's based on a Sanden or Sankyo 508 compressor at 60 MPH. The blower motor is capable of 240 CFM. Minimum condenser dimensions would be 12"X18" but would prefer a 14"X20" sized condenser, or 280 sq. in.
            
  • Speedway Universal Fit Street Rod Heater, 12 Volt, 20,000 BTU
    Speedway Universal Fit Street Rod Heater, 12 Volt, 20,000 BTU
    (Part #910454)
    x
                

    These all new universal street rod heaters give you the option of heat in your custom ride with the ease of installation.  They feature a compact size, two-speed fan, and rear fan guard.

    • 9-1/2" x 6-1/2" x 7"
    • Adjustable louver to direct heat flow
    • 12V 20,000 BTU heater
    • Has rear exit hose connections for convenient mounting
  • 90 Degree Crimp-On O-Ring Heater Hose Fitting, -10 AN
    90 Degree Crimp-On O-Ring Heater Hose Fitting, -10 AN
    (Part #4281327)
    x
                

    These premium -10 size (7/8" x 14 TPI) crimp-on hose fittings feature O-ring seals and a 90 degree bend. Ideal for use with heater bulkhead plates.

    Note: Will need to be crimped by your local shop. 

  • LS EVAP Delete Plug
    $12.99
    $18.99
    LS EVAP Delete Plug
    (Part #91680916)
    x
                

    These EGR EVAP delete plugs are intended for use on non-pollution controlled, off-road vehicles only.

    • For GM LS engines
    • Hardware and O-ring are included

     

Filter

"Muscle Car, HVAC" Page 1 of 7

Page 1 of 7

  • Aeroquip FCF0809 Stainless Steel Braided AC Hose, -8 AN, 9 Ft. Length
    Aeroquip FCF0809 Stainless Steel Braided AC Hose, -8 AN, 9 Ft. Length
    (Part #617809)
    x
                This is a superior hose for air conditioning applications. The attractive hose has a stainless steel outer braid with a nylon inner tube for excellent refrigerant performance.
            
  • 90 Degree Crimp-On O-Ring Heater Hose Fitting, -10 AN
    90 Degree Crimp-On O-Ring Heater Hose Fitting, -10 AN
    (Part #4281327)
    x
                

    These premium -10 size (7/8" x 14 TPI) crimp-on hose fittings feature O-ring seals and a 90 degree bend. Ideal for use with heater bulkhead plates.

    Note: Will need to be crimped by your local shop. 

  • Heater Core for 1965-67 Ford Galaxie and Custom Passenger Car
    Heater Core for 1965-67 Ford Galaxie and Custom Passenger Car
    (Part #910399001)
    x
                For your 1965-67 Ford / Mercury passenger car, use a 100% new heater core,   not a marginal   recore like others sell. All heater cores are a   direct fit  factory replacement for applications without A/C. 
    • All new construction
    • Direct fit factory replacement for 1965-67 Ford Galaxie and Custom
    • Please note: non air applications

    Note: These heater cores may be shipped either aluminum or copper/brass, depending on application & inventory/stock. 

  • Holley 20-132 LS Accessory Drive Bracket-ALT, P/S, A/C
    Holley 20-132 LS Accessory Drive Bracket-ALT, P/S, A/C
    (Part #42520132)
    x
                Please view the product's page for more information
            
  • Heater Core for 1969-70 GM Full Size Passenger Car
    Heater Core for 1969-70 GM Full Size Passenger Car
    (Part #910398218)
    x
                For your 1969-70 GM full size passenger car, use a 100% new  heater core, not a marginal recore like others sell. All heater cores  are a direct fit factory replacement for applications not originally  equipped with A/C.
    • All new construction
    • Direct fit factory replacement for 1969-70 GM FULL SIZE
    Note: These heater cores may be shipped either aluminum or copper/brass, depending on application & inventory/stock.
  • Under Dash AC Unit
    $229.99
    $279.99
    Under Dash AC Unit
    (Part #91000535)
    x
                

    Looking for a simple under-the-dash A/C cooling unit? This compact air conditioning control box is just 16" long 4.25" tall and 11" deep. This unit features two large 2" X 6" air vents in front with a three-speed blower motor and cooling control adjustment.

    Note:  This unit consists of the AC evaporator, duct assembly and blower motor for the under dash use.  It will require the additional items of the compressor, hose kit, dryer and condenser to complete the A/C system.

  • Heater Core for 1963-64 GM Mid Size Passenger Car w/ Factory Air
    Heater Core for 1963-64 GM Mid Size Passenger Car w/ Factory Air
    (Part #910399047)
    x
                For your 1963-64 GM Full Size passenger car, use a 100% new heater core,   not a marginal   recore like others sell. All heater cores are a   direct fit  factory replacement for applications with A/C. 
    • All new construction
    • Direct fit factory replacement for 1963-64 GM Full Size passenger car with factory air
    • Please note: factory air applications

    Note: These heater cores may be shipped either aluminum or copper/brass, depending on application & inventory/stock. 

  • Air Conditioning Kit w/ Condenser
    Air Conditioning Kit w/ Condenser
    (Part #428200)
    x
                

    The days of riding around trying to look cool while sweating your butt off are gone! So is going to the junkyard and trying to find used parts to cobble up an a/c system. These kits have three dash vents and two defrost ducts and are engineered for 1930's coupes, pick-ups and smaller cars.

    These are designed with both the a/c evaporator and heater core in one unit which helps keep size and installation time down. They fit under the dash just like a new car and allow disassembly without removing the unit from the car.

    They include dash louvers, defrost louvers, switch panel, a/c hose kit, dryer with switch, Sanden 508 compressor  with V-belt pulley, and evaporator/heater assembly. They are available with or without condenser and standard finish or deluxe polished aluminum compressor.

    Hoses will need to be crimped by your local shop. R134a Freon required, but not supplied. Compressor brackets and heater hoses sold separately.

    Instructions (PDF) 

  • 1964-68 Mustang Heater Core
    $69.99
    1964-68 Mustang Heater Core
    (Part #91739022)
    x
                Here is a 100% new heater core, not a marginal recore like others sell, for your 1964-1968 Mustang. For cars without factory air conditioning.
            
  • Heater Core for 1971-90 GM Full Size Passenger Car
    Heater Core for 1971-90 GM Full Size Passenger Car
    (Part #910398219)
    x
                For your 1971-90 GM Full Size passenger car, use a 100% new heater core, not a marginal   recore like others sell. All heater cores listed are a direct fit  factory replacement for applications without A/C. 
    • All new construction
    • Direct fit factory replacement
    • Please note: non air applications

    Note: These heater cores may be shipped either aluminum or copper/brass, depending on application & inventory/stock. 

  • 1965-67 Chevelle Heater Core
    $74.99
    1965-67 Chevelle Heater Core
    (Part #91739040)
    x
                For a 1965-1967 Chevelle. These are 100% new heater cores. Not marginal recores like others sell. All heater cores listed are for cars without factory air conditioning. 
            
  • Aeroquip FCF1003 Stainless Steel Braided AC Hose, -10 AN, 3 Ft. Length
    Aeroquip FCF1003 Stainless Steel Braided AC Hose, -10 AN, 3 Ft. Length
    (Part #617103)
    x
                This is a superior hose for air conditioning applications. The attractive hose has a stainless steel outer braid with a nylon inner tube for excellent refrigerant performance.
            
  • Straight Nickel Plated AC Fitting w/Port, -6 AN to -6 AN
    Straight Nickel Plated AC Fitting w/Port, -6 AN to -6 AN
    (Part #6171912)
    x
                These handsome nickel plated steel fittings are reuseable. This AN6 straight fitting features a high side R134a port.
            
  • Heater Core for 1966-71 Dodge Charger and Coronet
    Heater Core for 1966-71 Dodge Charger and Coronet
    (Part #910399101)
    x
                For your 1966-71 Charger / Coronet, use a 100% new heater core,    not a marginal   recore like others sell. All heater cores are a    direct fit  factory replacement for applications without A/C. 
    • All new construction
    • Direct fit factory replacement for 1966-71 Dodge Charger and Coronet
    • Please note non air applications

    Note: These heater cores may be shipped either aluminum or copper/brass, depending on application & stock. 

  • Air Conditioning Condenser, 12 x 19-1/2 Inch
    Air Conditioning Condenser, 12 x 19-1/2 Inch
    (Part #42815215)
    x
                

    Horizontal mount aluminum A/C condenser with parallel flow. This is 12" wide by 19-5/8" tall with fittings on passenger/right hand side. Top fitting is 90 degree pointed down and lower fitting is straight point out horizontal.

    Has one -6 AN and one -8 AN fitting.

  • 1957 Chevy Car Heater Core
    $199.99
    1957 Chevy Car Heater Core
    (Part #91734460)
    x
                

    These are a 100% new, factory replacement Tri-Five heater core. Not a marginal recore like others sell. For '57 Chevrolet cars without factory air conditioning. We also recommend the mounting plate, which is normally rusted beyond use.

    Note: General Motors produced two different style heater cores for these vehicles.  The heater cores we carry are a reproduction of the "deluxe" model, not the "standard."

  • 135 Degree Nickel Plated AC Fitting, O-Ring Pilot w/Port, -10 AN
    135 Degree Nickel Plated AC Fitting, O-Ring Pilot w/Port, -10 AN
    (Part #6171894)
    x
                These handsome nickel plated steel fittings are reuseable. This 135 degree AN10 fitting features a low side R134a port.
            
  • Heater Core for 1967-72 Ford / Mercury Passenger Car w/ Factory Air
    Heater Core for 1967-72 Ford / Mercury Passenger Car w/ Factory Air
    (Part #910399032)
    x
                For your 1967-72 Ford / Mercury Mid Size passenger car, use a 100% new heater core,   not a marginal   recore like others sell. All heater cores are a   direct fit  factory replacement for applications with A/C. 
    • All new construction
    • Direct fit factory replacement for:
      • 1967-72 Ford Mustang / Mercury Cougar with factory air
      • 1969-72 Comet with factory air
      • 1970-72 Pinto / Maverick with factory air
    • Please note: factory air applications

    Note: These heater cores may be shipped either aluminum or copper/brass, depending on application & inventory/stock. 

  • Crimp-On A/C O-Ring Fitting, 90 Degree, -6 AN
    Crimp-On A/C O-Ring Fitting, 90 Degree, -6 AN
    (Part #4282321)
    x
                90° elbow A/C O-ring crimp fitting with in a -6 (5/8" x 18 TPI) size.
            
  • Heater Core for 1962 Chevrolet Impala
    $111.99
    $139.99
    Heater Core for 1962 Chevrolet Impala
    (Part #910399053)
    x
                For your 1962 GM Full Size passenger car, use a 100% new heater core,   not a marginal   recore like others sell. All heater cores are a   direct fit  factory replacement for applications without A/C. 
    • All new construction
    • Direct fit factory replacement for 1962 Chevrolet Impala
    • Please note: non air applications

    Note: These heater cores may be shipped either aluminum or copper/brass, depending on application & inventory/stock. 

Goto Previous PagePrevious Page
1 2 3 4 5 6 7