Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products

Speedway Motors stocks all the best names in American muscle car carburetors and intake manifolds! Plus, we have a great selection of fuel cells and gas pedals, as well as electric and mechanical fuel pumps. Don't forget to let your engine breath with filters from K&N and R2C. Speedway can fuel your need for speed!

"Muscle Car, Fuel Storage" Page 1 of 13

  • RCI 126 Replacement Flapper Valve, 16 Bolt
    RCI 126 Replacement Flapper Valve, 16 Bolt
    x
                

    This fuel tank cap seal flapper is designed to retrofit all RCI Circle Track cells with the 16 bolt oval type 4" cap assemblies.

    This flapper is designed to slow the fuel leakage in the event of a vehicle roll over.

    A must have safety item! 

    • Replacement nylon flapper valve for all "16 bolt top" RCI fuel cells
    • Compatible with gas or alcohol
    • Overall Length: 4-3/8"
    • Overall Width: 3-3/4"
    • Overall Thickness: .03"
    • Clear plastic material

    Note: Per vendor, this flapper valve should be replaced on a yearly basis.

  • Aeroquip Special Application Socketless AN Hose, Black
    Aeroquip Special Application Socketless AN Hose, Black
    x
                
  • Textile braid reinforcement
  • Low pressure design for use with socketless reuseable fittings only
  • No hose clamp necessary
  • Ideal hose for fuel line applications
  • 50,000 ft of hose in stock!
  • Construction: AQP elastomer tube, textile braid reinforcement, black AQP elastomer cover.

    Application: For gasoline, fuel and lubricating oils, air and water. Not recommended for hydraulic impulse applications and is not approved for air brake, hydraulic brake or power steering applications.

    Operating Range: Max Operating pressure: 250 PSI. Minimum burst pressure: 1000 PSI. Operating Temperature Range -40°F to 300°F. Air not to exceed +250°F and water not to exceed +180°F. Reduced pressure operation allows for temperatures up to 300°F.

    Aeroquip Hose Sizing Guide (GIF)

    Hose Fitting Sizing Chart (GIF)

  • Black Straight -6 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    Black Straight -6 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    x
                

    These straight flare adapters connect 3/8" pipe to straight -6 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Black finish will give your engine compartment the look you are after.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fuel line hose connector
    • -6 AN to 3/8" aluminum pipe adapter
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Black anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Aeroquip Special Application Socketless AN Hose, Blue
    Aeroquip Special Application Socketless AN Hose, Blue
    x
                
  • Textile braid reinforcement
  • Low pressure design for use with socketless reuseable fittings only
  • No hose clamp necessary
  • Ideal hose for fuel line applications
  • 50,000 ft of hose in stock!

    Construction: AQP elastomer tube, textile braid reinforcement, blue AQP elastomer cover.

    Application: For gasoline, fuel and lubricating oils, air and water. Not recommended for hydraulic impulse applications and is not approved for air brake, hydraulic brake or power steering applications.

    Operating Range: Max Operating pressure: 250 PSI. Minimum burst pressure: 1000 PSI. Operating Temperature Range -40°F to 300°F. Air not to exceed +250°F and water not to exceed +180°F. Reduced pressure operation allows for temperatures up to 300°F.

    Aeroquip Hose Sizing Guide (GIF)

  • Hose Fitting Sizing Chart (GIF)

  • Straight Chrome Fitting, 3/8 Inch Hose to 3/8 Inch NPT
    Straight Chrome Fitting, 3/8 Inch Hose to 3/8 Inch NPT
    x
                

    These chrome plated push-on brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb ends
    • 3/8" Hose to 3/8" NPT adapter
    • Fuel line hose connector
    • Straight angle
  • Black Straight -6 AN Flare to 1/4 Inch NPT Pipe Adapter Fitting
    Black Straight -6 AN Flare to 1/4 Inch NPT Pipe Adapter Fitting
    x
                

    These straight flare adaptors connect 1/4" pipe to straight -6 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Black finish will give your engine compartment the look you are after.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fuel line hose connector
    • -6 AN to 1/4" aluminum pipe
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Black anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Professional Products 10415 Holley 4150 Dual Feed Fuel Line Kit, -8 AN
    Professional Products 10415 Holley 4150 Dual Feed Fuel Line Kit, -8 AN
    x
                These dual feed fuel line kits give you the looks, performance and flexibility your car deserves. Fuel log features -8 AN inlet, 1/8" NPT tapped fuel pressure gauge port, and allows you to have a fuel tank return if needed.

    Fuel line fits Holley 4150 style Double Pumper carburetors with 7/8"-20 inlets.

  • Straight Chrome Fitting, 5/16 Inch Hose to 1/4 Inch NPT
    Straight Chrome Fitting, 5/16 Inch Hose to 1/4 Inch NPT
    x
                

    These socketless chrome plated brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb connector
    • 5/16" Hose to 1/4" NPT adapter
    • Straight angle
  • Aluminum -8 AN Female to -6 AN Male Reducer Fitting
    Aluminum -8 AN Female to -6 AN Male Reducer Fitting
    x
                

    Aluminum female to male adapter for 37° AN pipe fittings. Blue anodized finish.

    • -8AN female to -6AN male fuel line hose connector

    Fitting Thread Application Chart (GIF)

  • Aeroquip FBG0600 FC300 High Pressure Hose, -6 AN, Per Ft.
    Aeroquip FBG0600 FC300 High Pressure Hose, -6 AN, Per Ft.
    x
                

    Aeroquip FC 300 hose is designed for high pressure fluid applications such as power steering line. The FC300 hose features a blue, abrasion-resistant fabric cover over a synthetic rubber inner tube for longer life. This high pressure hose is ideal for power steering, hydraulics, air, fuel and lubricating oil applications.

    • Max operating pressure is 2250 psi
    • Minimum bend radius is 4"
    • Temperature range of -55°F to +300°F
    • Hose is sold by the foot

    Note: The FC300 Hose only works with FC300 steel fittings (not included). Easily assembles with a bench vise and/or wrenches. Ends are reusable.

    AN Thread Sizing Guide (GIF)

    AN 6 Hose Application Chart (GIF)

  • Straight Chrome Fitting, 3/8 Inch Hose to 1/4 Inch NPT
    Straight Chrome Fitting, 3/8 Inch Hose to 1/4 Inch NPT
    x
                

    These chrome plated brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb end
    • 3/8" Hose to 1/4" NPT adapter
    • Straight angle line connector

     

  • Chrome 90   Adapter Fitting, 3/8 Inch Hose to 1/4 NPT
    Chrome 90 Adapter Fitting, 3/8 Inch Hose to 1/4 NPT
    x
                

    These chrome plated brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb ends
    • 3/8" Hose to 1/4" NPT
    • 90 Degree angle
  • Chrome 90   Adapter Fitting, 3/8 Inch Hose to 3/8 NPT
    Chrome 90 Adapter Fitting, 3/8 Inch Hose to 3/8 NPT
    x
                

    These chrome plated brass adapter fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb ends
    • 3/8" push-on hose to 3/8" NPT fuel line connector
    • 90 Degree angle
  • Black 90 Degree -3 AN Flare to 1/8 Inch NPT Pipe Adapter Fitting
    Black 90 Degree -3 AN Flare to 1/8 Inch NPT Pipe Adapter Fitting
    x
                

    Aluminum pipe thread to 37° AN adapter fitting. Black anodized finish will give your engine compartment the look you are after.

    • 90 degree elbow
    • -3 AN flare to 1/8" NPT thread
    • Fuel line hose connector

    Fitting Thread Application Chart (GIF)

  • Aluminum Bulkhead Jam Nut, Blue, -6 AN
    Aluminum Bulkhead Jam Nut, Blue, -6 AN
    x
                

    Aluminum bulkhead jam nuts for AN fittings. Blue anodized finish.

    AN Thread Sizing Guide (GIF)

    Fitting Thread Application Chart (GIF)

  • Aeroquip Straight Full Flow Swivel Hose End Coupler Fitting, -6 AN
    Aeroquip Straight Full Flow Swivel Hose End Coupler Fitting, -6 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a red and blue anodized finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617306).

    • -6 AN female to push-on style adapter
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • Unique taper design ensures easy assembly
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Accepts a variety of lightweight aluminum AN style adapters & fittings
    • Works great with custom fuel lines
    • Available in Red/Blue corrosion resistant finish

    Straight full flow ends come in sizes of AN4, AN6, AN8, AN10, AN12, and AN16.

    Fitting Thread Application Chart (GIF)

  • Nickel Straight Flare to Aluminum Pipe Adapter Fitting, -6 AN to 3/8 Inch NPT
    Nickel Straight Flare to Aluminum Pipe Adapter Fitting, -6 AN to 3/8 Inch NPT
    x
                

    Many street rodders find that red or blue anodized aluminum AN hose fittings look too racy on their cars, but standard steel versions are just too plain.

    Speedway offers a great looking alternative with these nickel plated aluminum hose fittings and adapters from Aeroquip. Lighter and more affordable than stainless steel, these electoless nickel plated pieces combine great corrosion resistance with a neutral color and classy appearance.

    These straight flare adaptors connect 3/8" pipe to straight -6 AN fittings. They are lightweight and feature a 37° sealing angle. 

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum connector fitting
    • -6 AN to 3/8" aluminum pipe adapter
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in nickel plated finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Russell Performance 639200 3/8 Inch Tubing - AN 6 Female Flare Adapter
    Russell Performance 639200 3/8 Inch Tubing - AN 6 Female Flare Adapter
    x
                

    Tubing to AN flare adapters are for use with aluminum tubing only (not steel tubing). 

    • Connects 3/8" aluminum tube to -6 AN adapters
    • Unique crimp design eliminates tube flaring
    • Not for use with fuel injection

    Learn more about flaring lines and how to select proper automotive fittings by reading our tech article. The Principles of Automotive Fittings.

  • Female Aluminum Swivel Coupler Fitting, -6 AN
    Female Aluminum Swivel Coupler Fitting, -6 AN
    x
                

    Female aluminum swivel coupler for 37° AN fittings.

    • -6 AN female adapter
    • Straight style fuel line hose connector
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Red/Blue corrosion resistant finish

    Fitting Thread Application Chart (GIF)

  • Black Straight -8 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    Black Straight -8 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    x
                

    These straight flare adapters connect 3/8" pipe to straight -8 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Black finish will give your engine compartment the look you are after.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fuel line hose connector
    • -8 AN male to 3/8" aluminum pipe
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Black anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • 3/8 Inch-24 Inverted Male Flare Plug for Master Cylinder Ports
    3/8 Inch-24 Inverted Male Flare Plug for Master Cylinder Ports
    x
                These threaded plug fittings are designed for use on master cylinders with 3/8"-24 IFM unused ports.
    • 3/8"-24 IFF Plug
    • Use to plug unused ports on double sided master cylinder
  • Straight Chrome Fitting, 3/8 Inch Hose to 1/8 Inch NPT
    Straight Chrome Fitting, 3/8 Inch Hose to 1/8 Inch NPT
    x
                

    These chrome plated brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb ends
    • 3/8" Hose to 1/8" NPT
    • Straight angle
  • Aluminum Pipe Bushing Reducer Fitting, 1/2 NPT to 3/8 NPT
    Aluminum Pipe Bushing Reducer Fitting, 1/2 NPT to 3/8 NPT
    x
                

    Aluminum pipe bushing reducer adapter fitting. Blue anodized finish.

    Fitting Thread Application Chart (GIF)

  • Aluminum 1/8 Inch NPT Hose Barb Fitting
    Aluminum 1/8 Inch NPT Hose Barb Fitting
    x
                Use this billet aluminum hose barb fitting in place of the ugly old brass fittings.  These aluminum fittings accept 5/16" or 3/8" I.D. hose (must be clamped) and thread into 1/8" NPT.
            
  • Aluminum -10 AN Female to -8 AN Male Reducer Fitting
    Aluminum -10 AN Female to -8 AN Male Reducer Fitting
    x
                

    Aluminum female to male reducer for 37° AN fittings. Blue anodized finish.

    • -10 AN Female to -8 AN Male adapter
    • Straight style fuel line hose connector
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Blue anodized finish

    Fitting Thread Application Chart (GIF)

  • Tight Fit 90 Degree Socketless Reusable Fittings
    Tight Fit 90 Degree Socketless Reusable Fittings
    x
                

    These tight fit 90° steel fittings work great for a variety of different applications.  They feature your choice of -4, -6, or -8 AN male/female ends with a corrosion resistant finish.

    • Working pressure of 5500 psi 
    • 90° steel fuel line hose connector
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Choose from -4 AN, -6 AN, or -8 AN sizes

    Socketless Fitting Application Chart (GIF)

    AN Thread Size Guide (GIF)

    Fitting Thread Size Guide (GIF)

  • Premium Black Synthetic Hose - AN8
    Premium Black Synthetic Hose - AN8
    x
                

    This lightweight motorsports inspired hose has a rubber core, flexible braided nylon cover in a black color, and is resistant to oil, fuels, and coolants. Features a 500 psi working pressure and an operating range of -40° F to +300° F. Designed to be used with both crimp style and full flow type fittings. 

    • Vacuum Rating: 28 in. hg.
    • Weight Per Ft.: 0.120 lbs.
    • Minimum Bend Radius:  3.5 in.

    Works great as a fuel line for gasoline and alcohol fuels.

  • Premium Black Synthetic Hose - AN16
    Premium Black Synthetic Hose - AN16
    x
                

    This lightweight motorsports inspired hose has a rubber core, flexible braided nylon cover in a black color, and is resistant to oil, fuels, and coolants. Features a 350 psi working pressure and an operating range of -40° F to +300° F. Designed to be used with both crimp style and full flow type fittings. 

    • Vacuum Rating: 28 in. hg.
    • Weight Per Ft.: 0.320 lbs.
    • Minimum Bend Radius:  5.5 in.

     

Goto Previous PagePrevious Page
1 2 3 4 5 ... 13