Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Muscle Car Air & Fuel Delivery At Speedway Motors

Speedway Motors stocks all the best names in American muscle car carburetors and intake manifolds! Plus, we have a great selection of fuel cells and gas pedals, as well as electric and mechanical fuel pumps. Don't forget to let your engine breath with filters from K&N and R2C. Speedway can fuel your need for speed!

Featured Products
MSD 2225 In-Line Hi-Pressure Fuel Pump
MSD 2225 In-Line Hi-Pressure Fuel Pump
x
            

Most modern engines have a hi-pressure fuel pump located in the gas tank. If you are transplanting one of these engines into your hot rod, what are you going to do for a fuel pump? This MSD pump can be mounted on the frame and can put out up to 43 gph at 40 psi or 39 gph at 80 psi.

  • Flows 43 gph (282 lb/hr) gasoline @ 40 psi and 12 volts/5.4 amps 
  • Supports most multiport EFI systems up to 500 horsepower
  • Mounts in-line (out of the fuel tank)
  • Roller vane pump mechanism is extremely resistant to clogging and jamming
  • Has 3/8” hose barb inlet and 5/16" hose barb outlet
  • Made in the USA

MSD Rebate (Link)

Three Plain 9 Super 7   Carbs on 1957-86 Small Block Chevy Edelbrock Intake
Three Plain 9 Super 7 Carbs on 1957-86 Small Block Chevy Edelbrock Intake
x
            

This tri power kit uses the Edelbrock C-357-B S/B Chevy 3x2 intake with Speedway's 9 Super 7® carbs. It has progressive linkage to give you good driveability and economy, but power when you need it. The manifold has a balanced 180° firing order port runner arrangement. It contains an exhaust gas heat riser and offers excellent performance potential. (idle-5500 rpm)

Kit includes three carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required. Fits 1957-1986 Chevy 262-400 c.i.d. small-block Chevys.

9 Super 7® Linkage Instructions (PDF)

Note: Not applicable to an HEI based distributor system due to a clearance issue. This system must be used in conjunction with a small diameter based distributor.

The 9Super7 Carb  makes setting up a multiple carburetor induction system easier than when Strombergs were available new. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb set-up.

  • Three Deuce carburetor setups come with two "secondary" carbs for front and rear intake position and one "primary" carb for central/middle position
  • All-new tooling for crisp, flawless castings
  • New aluminum base assembly allows for cooler fuel temps and better fuel efficiency as compared to the original cast iron design
  • Stainless steel screws and hardware
  • Original troublesome needle and seat replaced by a Grose-style fuel inlet valve to better cope with higher fuel pressures and improved high speed running 
  • Will not stick or dribble like the old Viton-tipped needle and seat setups
  • Extended brass throttle shaft to simplify multi-carb linkage
  • Primary Carb - (1) Middle Position
    • Choke assembly, accelerator pump, and jets have all been faithfully retained and accept standard Stromberg parts
  • Secondary Carb - (2) Front and Rear Position
    • Special base plate with no idle circuits or choke linkage
    • Special butterflies and shafts installed
    • Works best with progressive linkage
    • Idle only off the center or main carburetor
    • No more plug foul

Note: The secondary carbs have NO choke, and they have NO idle system.

915-11655 Primary 9 Super 7 Carburetor Instructions (PDF)

LS1 Complete Fuel Delivery Kit
$169.99
Product Rating: 4.57 Stars
LS1 Complete Fuel Delivery Kit
x
            

To make your LS1 transplant a little less painful, we put together these kits for you. If you already have a fuel pump in the tank, use the filter/regulator kit 910-12800.

This kit includes a high pressure MSD in-line pump capable of 43 gph @ 40 psi or 39 gph @ 80 psi, a filter/regulator assembly, and all necessary fittings (including fuel rail fitting). Pump draws only 5.4 amps and supports up to 500 horsepower. Pump features 3/8" hose barb inlet and 5/16" barb outlet.

Hose and additional fittings sold separately. MSD pump requires the use of 5/16" high pressure rubber hose with appropriate fuel injection hose clamps for the pressure side of the pump.

Holley 0-4412CT Circle Track 500 CFM 2 Barrel Carburetor
Holley 0-4412CT Circle Track 500 CFM 2 Barrel Carburetor
x
            This 500cfm 4412CT Holly carb shares the hugely  successful features of the original 4412C but with a couple changes  aimed for circle track cars. The choke has been removed but the horn  remains and has been specially calibrated for circle track use. The  4412C Holley carb is easily the most winningest two barrel carburetor on the market  and comes out of the box ready to run. 

Features:
  • Choke delete
  • Choke horn remains
  • 50cc accelerator pump
  • 1 timed (spark) port, 1 full vacuum, & 1 PCV port
  • The mandated carbs for many oval track racing sanctioning bodies
  • Calibrated specifically for circle track use

"Muscle Car, Air and Fuel Delivery" Page 1 of 25

  • Late Carburetor Adapter
    $24.99
    Product Rating: 4.00 Stars
    Late Carburetor Adapter
    x
                

    Bolt a newer type 4-bolt carb (3-1/4" x 1-7/8", like Rochester 2GC) to an early 3-bolt manifold. Aluminum casting.

    560-5159 Instructions (PDF)

  • RCI 126 Replacement Flapper Valve, 16 Bolt
    RCI 126 Replacement Flapper Valve, 16 Bolt
    x
                

    This fuel tank cap seal flapper is designed to retrofit all RCI Circle Track cells with the 16 bolt oval type 4" cap assemblies.

    This flapper is designed to slow the fuel leakage in the event of a vehicle roll over.

    A must have safety item! 

    • Replacement nylon flapper valve for all "16 bolt top" RCI fuel cells
    • Compatible with gas or alcohol
    • Overall Length: 4-3/8"
    • Overall Width: 3-3/4"
    • Overall Thickness: .03"
    • Clear plastic material

    Note: Per vendor, this flapper valve should be replaced on a yearly basis.

  • Holley Carburetor Gas Needle and Seat, .110 Inch
    Holley Carburetor Gas Needle and Seat, .110 Inch
    x
                "Viton" needle and seat is resistant to dirt and provides superior seal when closed. Size .110" for gas carbs. Gasket not included. 
            
  • Fuel Filter Mounting Bracket
    Fuel Filter Mounting Bracket
    x
                

    These fuel filter mounting brackets are CNC machined aluminum. Available in 1-3/8", 1-1/2", or 1-3/4" round tubing.

    These brackets are designed to be used with our filters. Hole is 2" inner diameter. 

  • Open 4 Barrel Carburetor Base Gasket
    Open 4 Barrel Carburetor Base Gasket
    x
                Open base gaskets.
            
  • Lokar SRK-4000 Carburetor Bracket and Return Spring
    Lokar SRK-4000 Carburetor Bracket and Return Spring
    x
                

    Stainless bracket mounts to rear of Holley, Edelbrock, AFB, Quadrajet, Demon, and In-Line Dual Quads. Stainless bracket and dual stainless springs are used to mount Lokar’s Throttle Cable and Kickdown kits. Design provides improved clearance on Edelbrock carbs. Includes tension screw to prevent bracket from movement under extreme pressure on a kickdown cable, such as with a 700-R4 transmission.

    Mounts Lokar Throttle Cables and Kickdowns for a nice clean setup. Includes allen wrench to adjust the set screw.

  • Carb and Fuel Pump Fitting, 1/2 Inch-20, AN 6
    Carb and Fuel Pump Fitting, 1/2 Inch-20, AN 6
    x
                

    #6 Ford, Chrysler and early Chevy fuel pumps with 1/2"-20 inverted flare thread.

    Fitting Thread Application Chart

  • Tri-Bar Wing Nut Style Air Cleaners
    Tri-Bar Wing Nut Style Air Cleaners
    x
                

    Just the ticket for that tri-power setup! These chrome plated steel air cleaners have a 4" x 2" replaceable paper element and will fit 2-5/8" and 2-5/16" carbs.

    Comes with a metal screw to secure it to the carb neck from the top side. Includes tri-bar style retaining nut.

  • Aeroquip Special Application Socketless AN Hose, Black
    Aeroquip Special Application Socketless AN Hose, Black
    x
                
  • Textile braid reinforcement
  • Low pressure design for use with socketless reuseable fittings only
  • No hose clamp necessary
  • Ideal hose for fuel line applications
  • 50,000 ft of hose in stock!
  • Construction: AQP elastomer tube, textile braid reinforcement, black AQP elastomer cover.

    Application: For gasoline, fuel and lubricating oils, air and water. Not recommended for hydraulic impulse applications and is not approved for air brake, hydraulic brake or power steering applications.

    Operating Range: Max Operating pressure: 250 PSI. Minimum burst pressure: 1000 PSI. Operating Temperature Range -40°F to 300°F. Air not to exceed +250°F and water not to exceed +180°F. Reduced pressure operation allows for temperatures up to 300°F.

    Aeroquip Hose Sizing Guide (GIF)

    Hose Fitting Sizing Chart (GIF)

  • Three Plain 9 Super 7   Carbs on 1957-86 Small Block Chevy Edelbrock Intake
    Three Plain 9 Super 7 Carbs on 1957-86 Small Block Chevy Edelbrock Intake
    x
                Please view the product's page for more information
            
  • Quick Release Cable or Linkage End, 1/4-28 RH
    Quick Release Cable or Linkage End, 1/4-28 RH
    x
                These steel ends are perfect for throttle cable or linkage that needs to be quick release. They have the same thread on the stud as they do in the body. 
            
  • K&N Filters 99-0516 Air Filter Oil, Aerosol
    K&N Filters 99-0516 Air Filter Oil, Aerosol
    x
                

    K&N Air Filter Oil is the only oil specially formulated to work in combination with the cotton fabric in K&N Filtercharger elements providing a superior air filtration system. When used as directed, it quickly penetrates the filter pleats, where it remains suspended in the cotton fabric. Saturation is maintained until the element is cleaned with K&N Air Filter Cleaner.

    NOTE: Aerosol items cannot be shipped by air.

  • Lokar BAG-6099 1967-69 Camaro/Firebird E-Brake Pedal Pad
    Lokar BAG-6099 1967-69 Camaro/Firebird E-Brake Pedal Pad
    x
                These billet aluminum pads are the perfect finishing touch for your dream car. The pedal pads attach to your existing brake pedals. 
            
  • Pump Frame Tube Clamp for 1-1/4 Inch Tube
    Pump Frame Tube Clamp for 1-1/4 Inch Tube
    x
                

    Pump Frame Tube Clamp for 1.250" Tube for FUELAB Prodigy pump.

  • Louvered Style Air Cleaners
    $9.99
    Product Rating: 4.64 Stars
    Louvered Style Air Cleaners
    x
                

    Just the ticket for that tri-power setup! Chrome plated steel housing with 4" x 2" replaceable paper element. Fits Holley 94, Stromberg 97, Speedway 9 Super 7, Demon 98 and Rochester 2 barrels (all with 2-5/8" neck). 

    Retained with a #36 hose clamp.

  • Throttle Ball Assortment
    $9.99
    Product Rating: 5.00 Stars
    Throttle Ball Assortment
    x
                

    Many applications use a ball on the carburetor arm to hook the linkage to. This handy little assortment of 4 throttle balls with various threads will allow you to finish up linkage.

    Includes

    • 1/4" threaded stud, .222" ball, .131" ball stud
    • 1/4" threaded stud, .250" ball, .160" ball stud
    • 3/16" threaded stud, .267" ball, .157" ball stud
    • 3/16" threaded stud, .241" ball, .132" ball stud
  • Edelbrock 1405 Performer 600 CFM 4 Barrel Carburetor, Manual Choke
    Edelbrock 1405 Performer 600 CFM 4 Barrel Carburetor, Manual Choke
    x
                

    Edelbrock Performer Series four barrel carbs have proven themselves to be easy to tune with great drivability. Whether you need to replace an aging stock carb or are looking for a performance 4 barrel carb to top off your hot rod, the Edelbrock Performer Series carbs are the best choice for performance and value. All Edelbrock parts are proudly made in the U.S.A.  

    This 600 CFM 4 barrel carburetor is designed and calibrated for optimum street performance in small-block and some big-block engines. Match with a variety of manifolds that include Edelbrock Performer, Performer EPS, Performer RPM, RPM Air-Gap, Torker II and other brands of similar design. Includes manual choke and detailed instructions. Ford/Mopar throttle adapter arms sold separately. 

    Edelbrock 600 CFM 4 Barrel Carburetor Installation Instructions (PDF)

     Top It Off Rebate (PDF)

  • MSD 2225 In-Line Hi-Pressure Fuel Pump
    MSD 2225 In-Line Hi-Pressure Fuel Pump
    x
                

    Most modern engines have a hi-pressure fuel pump located in the gas tank. If you are transplanting one of these engines into your hot rod, what are you going to do for a fuel pump? This MSD pump can be mounted on the frame and can put out up to 43 gph at 40 psi or 39 gph at 80 psi.

    • Flows 43 gph (282 lb/hr) gasoline @ 40 psi and 12 volts/5.4 amps 
    • Supports most multiport EFI systems up to 500 horsepower
    • Mounts in-line (out of the fuel tank)
    • Roller vane pump mechanism is extremely resistant to clogging and jamming
    • Has 3/8” hose barb inlet and 5/16" hose barb outlet
    • Made in the USA

    MSD Rebate (Link)

  • Lokar DBW-6070 Chrome Drive-By-Wire Spoon Pedal Arm for DBW Throttle
    Lokar DBW-6070 Chrome Drive-By-Wire Spoon Pedal Arm for DBW Throttle
    x
                Chrome plated steel pedals for use with Lokar drive-by-wire throttle control modules. Pedals feature a splined adjustable mount and spring-loaded return.
            
  • Carb Linkage Thread End for 9 Super 7   /Stromberg 97/Demon 98 Carbs, RH
    Carb Linkage Thread End for 9 Super 7 /Stromberg 97/Demon 98 Carbs, RH
    x
                

    This carb linkage rod end has 3/16" fine RH threads (also known as 10-32).  It is intended for use with 9 Super 7 ®, Stromberg 97, and Demon 98 carburators.

    • 3/16" fine RH threads (10-32)
    • Secures with pin
    • Steel
    • .430" Diameter
    • Application:
      • 9 Super 7 ®
      • Stromberg 97
      • Demon 98
  • Air Cleaner Nut
    $9.99
    Product Rating: 3.67 Stars
    Air Cleaner Nut
    x
                

    Easy grip air cleaner nut features a bottom O-ring seal to keep dust and debris from entering your engine. Available for 1/4" or 5/16" studs.

    • Diameter at Top:  1-1/2"
    • Diameter at Base:  7/8"
    • Height:  1-1/4"
  • 3-7/8 Inch Washable Air Filters
    3-7/8 Inch Washable Air Filters
    x
                

    Our washable replacement filters outlast typical paper media filters because they can be washed and reused. Simply wash the filter using K&N Filter Cleaner and then re-oil it with K&N Air Filter Oil.

  • 6-3/8 Inch Chrome Air Cleaner, 4 Barrel Carb, 5-1/8 Inch Neck
    6-3/8 Inch Chrome Air Cleaner, 4 Barrel Carb, 5-1/8 Inch Neck
    x
                

    Keep the air entering your engine clean with our chrome plated steel air cleaners. They feature a recessed base and have a 6-3/8 in. diameter.  These air cleaners have a chrome plated steel housing with a paper filter element.

    6-3/8 Inch Chrome Air Cleaner, 4 Barrel Carb.

    • Chrome plated steel
    • 6-3/8" diameter and 2-1/2" tall filter element
    • Fits 4 barrel carbs with 5-1/8" neck
    • 3-3/4" tall from the base to the highest point on the top.
    • includes stud and wing nut
    • non-restricting flame retardant filter
    • unique sculptured design to fit most applications
    • performance engineered for increased breathing
    • designed to perform with today's large displacement engines

     

  • Speedway Throttle and Kickdown Cable Bracket Kit
    Speedway Throttle and Kickdown Cable Bracket Kit
    x
                Chrome plated, fully adjustable throttle cable and automatic transmission kickdown cable bracket bolts to the corner of most 2bbl. or 4 bbl. carburetors. Steel bracket locks in place and won't swivel. Works with OEM cable housings that have square plastic ends which snap into the bracket holes.
            
  • Small Block Chevy Intake Bolt Kits
    Small Block Chevy Intake Bolt Kits
    x
                A bolt kit for S/B Chevy intakes. All feature that unique King Chrome premium chrome plating.
            
  • 1955-57 Chevy Bel-Air / 150 / 210 Fuel Sending Unit, 3/8 Inch Outlet
    1955-57 Chevy Bel-Air / 150 / 210 Fuel Sending Unit, 3/8 Inch Outlet
    x
                These quality fuel sending units are designed as replacements for 1955-57 Chevy passenger vehicles.  They feature a 3/8" tube inverted flare outlet and will work with factory style fuel level gauges.
    • 55-57 BELAIR/150/210
    • 3/8" tube inverted flare outlet
    • OEM Replacement fuel sender/pickups
    • Designed for use with factory fuel level gauge

    LH/RH Swing Guide (Link)

    Ohms Chart (Link)

  • Mr. Gasket 1514 Chrome Fuel Pump Mounting Plate, Small Block Chevy
    Mr. Gasket 1514 Chrome Fuel Pump Mounting Plate, Small Block Chevy
    x
                

    Mr.Gasket announces a fuel pump mounting plate to dress up the fuel pump area of your engine. This chrome plated mounting plate, for the 265-400 cu. in. Chevrolet small block engine, is ideal for mounting a stock OEM pump. The mounting plate is precision cut to cover the stock fuel pump opening and is complete with gasket.

    • Quality chrome finish
    • Fits 265-400 SBC engines
    • Mounts stock OEM pump
    • Includes gasket
  • Replacement Screen for 97 Carb Scoop
    Replacement Screen for 97 Carb Scoop
    x
                4.5" x 4.5" flat replacement screen for 97 Carb Scoop 916-11001. Can also be used to make your own custom air intake screen or air filter screen.
            
  • Speedway Carburetor Bracket and Return Springs
    Speedway Carburetor Bracket and Return Springs
    x
                Stainless throttle cable bracket & spring set. Mounts to rear of Holley, Edelbrock, AFB, Quadrajet, Demon, and in-line dual quad carburetors. Dual spring design provides a safe, reliable throttle return when compared to single spring set-ups.

    Note: There is no provision in this bracket for an automatic transmission.
  • Edelbrock 2701 Performer EPS Chevy Intake Manifold
    Edelbrock 2701 Performer EPS Chevy Intake Manifold
    x
                

    Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

    Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most.

    IMCA racing approved.

    325-2701 Instructions (PDF)

  • Speedway Universal Throttle Linkage Bell Crank Kit
    Speedway Universal Throttle Linkage Bell Crank Kit
    x
                This bell crank kit features 12 mounting holes for multi-arm positioning and can be used in either push or pull type throttle linkages. Center hole is 1/4" diameter for easy mounting. Each arm has 3 holes for various throttle ratios. Includes all hardware needed for installation. 
            
  • Double End Carburetor Linkage, 9 Inches Long
    Double End Carburetor Linkage, 9 Inches Long
    x
                

    3/16" steel rod carburetor linkage with double ends. Thread size is 10-32 RH and LH. For use with 9 Super 7®, Stromberg 97, and Demon 98 carbs.

  • Universal Electric 4-7 PSI Fuel Pump
    Universal Electric 4-7 PSI Fuel Pump
    x
                

    Inexpensive solid state universal fuel pump for stock engines. Set for 4-7 psi and flows up to 35 gph. 12 volt. 1/8" npt inlet and outlet and includes two barbed hose fittings to connect to 5/16" hose.

    This pump is NOT self priming; it must be mounted below the gas tank to prevent the pump from running dry and over heating.  Failure to do so will cause premature failure of the pump.

    910-11520 Instructions (PDF) 

  • Holley Power Valve
    From: $9.99
    Product Rating: 5.00 Stars
    Holley Power Valve
    x
                Standard flow. Available sizes include: 2.5, 3.5, 4.5, 5.5, 6.5, 7.5, 8.5, 9.5 and 10.5 in hg. 

    High flow (big window valve) for alcohol. Available sizes include: 2.5, 3.5, 4.5, 5.5, 6.5, 8.5, 10.5 in hg.

  • Black Straight -6 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    Black Straight -6 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    x
                

    These straight flare adapters connect 3/8" pipe to straight -6 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Black finish will give your engine compartment the look you are after.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fuel line hose connector
    • -6 AN to 3/8" aluminum pipe adapter
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Black anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Offenhauser Chrome Universal Adjustable Fuel Pressure Regulator, 1-6 PSI
    Offenhauser Chrome Universal Adjustable Fuel Pressure Regulator, 1-6 PSI
    x
                This Offenhauser chrome universal fuel regulator is adjustable from 1-6 PSI, making it an affordable option for a variety of low pressure carbureted applications. Fuel pump regulator has 1/8" NPT female threads and includes both 5/16" and 3/8" hose barb connectors.
            
  • AN6 to 3/8 Inch Push-On for EFI
    AN6 to 3/8 Inch Push-On for EFI
    x
                

    Push-on EFI fittings for OEM hard lines. -6 AN male to 3/8" SAE quick-disconnect male. Zinc finish.

  • Stewart Warner 385C-F R Swing 6-12 Fuel Level Sending Unit, 240/33 Ohm
    Stewart Warner 385C-F R Swing 6-12 Fuel Level Sending Unit, 240/33 Ohm
    x
                Please view the product's page for more information
            
  • Aeroquip FBM4035 Hose End Coupler Fitting, 90 Degree, Blue/Red, -12 AN
    Aeroquip FBM4035 Hose End Coupler Fitting, 90 Degree, Blue/Red, -12 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a blue/red anodized finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617312).

    • -12 AN 
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • Unique taper design ensures easy assembly
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Accepts a variety of lightweight aluminum AN style adapters & fittings
    • Available in Blue/Red corrosion resistant finish

    90° Full Flow Ends come in sizes of AN4, AN6, AN8, AN10, AN12 and AN16.

    Fitting Thread Application Chart (GIF)

  • Holley 45-224 4150 Electric Choke Conversion Kits
    Holley 45-224 4150 Electric Choke Conversion Kits
    x
                

    These kits can be used to convert Holley carburetors which originally came equipped with manually–operated choke or automatic/electric operated choke. 

    Fits carburetor's with "external" vacuum source (Model 0-4412, 0-4776-2, 0-4777-2, 0-4778-2, 0-4779-2, 0-4780-2, 0-4781- 2, 0-6299, 0-6708 and 0-6709).

    427-45224 Instructions (PDF)

Goto Previous PagePrevious Page
1 2 3 4 5 ... 25