Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Muscle Car Air & Fuel Delivery At Speedway Motors

Speedway Motors stocks all the best names in American muscle car carburetors and intake manifolds! Plus, we have a great selection of fuel cells and gas pedals, as well as electric and mechanical fuel pumps. Don't forget to let your engine breath with filters from K&N and R2C. Speedway can fuel your need for speed!

Featured Products
MSD 2225 In-Line Hi-Pressure Fuel Pump
MSD 2225 In-Line Hi-Pressure Fuel Pump
x
            

Most modern engines have a hi-pressure fuel pump located in the gas tank. If you are transplanting one of these engines into your hot rod, what are you going to do for a fuel pump? This MSD pump can be mounted on the frame and can put out up to 43 gph at 40 psi or 39 gph at 80 psi.

  • Flows 43 gph (282 lb/hr) gasoline @ 40 psi and 12 volts/5.4 amps 
  • Supports most multiport EFI systems up to 500 horsepower
  • Mounts in-line (out of the fuel tank)
  • Roller vane pump mechanism is extremely resistant to clogging and jamming
  • Has 3/8” hose barb inlet and 5/16" hose barb outlet
  • Made in the USA

MSD Rebate (Link)

Three Plain 9 Super 7   Carbs on 1957-86 Small Block Chevy Edelbrock Intake
Three Plain 9 Super 7 Carbs on 1957-86 Small Block Chevy Edelbrock Intake
x
            

This tri power kit uses the Edelbrock C-357-B S/B Chevy 3x2 intake with Speedway's 9 Super 7® carbs. It has progressive linkage to give you good driveability and economy, but power when you need it. The manifold has a balanced 180° firing order port runner arrangement. It contains an exhaust gas heat riser and offers excellent performance potential. (idle-5500 rpm)

Kit includes three carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required. Fits 1957-1986 Chevy 262-400 c.i.d. small-block Chevys.

9 Super 7® Linkage Instructions (PDF)

Note: Not applicable to an HEI based distributor system due to a clearance issue. This system must be used in conjunction with a small diameter based distributor.

The 9Super7 Carb  makes setting up a multiple carburetor induction system easier than when Strombergs were available new. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb set-up.

  • Three Deuce carburetor setups come with two "secondary" carbs for front and rear intake position and one "primary" carb for central/middle position
  • All-new tooling for crisp, flawless castings
  • New aluminum base assembly allows for cooler fuel temps and better fuel efficiency as compared to the original cast iron design
  • Stainless steel screws and hardware
  • Original troublesome needle and seat replaced by a Grose-style fuel inlet valve to better cope with higher fuel pressures and improved high speed running 
  • Will not stick or dribble like the old Viton-tipped needle and seat setups
  • Extended brass throttle shaft to simplify multi-carb linkage
  • Primary Carb - (1) Middle Position
    • Choke assembly, accelerator pump, and jets have all been faithfully retained and accept standard Stromberg parts
  • Secondary Carb - (2) Front and Rear Position
    • Special base plate with no idle circuits or choke linkage
    • Special butterflies and shafts installed
    • Works best with progressive linkage
    • Idle only off the center or main carburetor
    • No more plug foul

Note: The secondary carbs have NO choke, and they have NO idle system.

915-11655 Primary 9 Super 7 Carburetor Instructions (PDF)

LS1 Complete Fuel Delivery Kit
$169.99
Product Rating: 4.63 Stars
LS1 Complete Fuel Delivery Kit
x
            

To make your LS1 transplant a little less painful, we put together these kits for you. If you already have a fuel pump in the tank, use the filter/regulator kit 910-12800.

This kit includes a high pressure MSD in-line pump capable of 43 gph @ 40 psi or 39 gph @ 80 psi, a filter/regulator assembly, and all necessary fittings (including fuel rail fitting). Pump draws only 5.4 amps and supports up to 500 horsepower. Pump features 3/8" hose barb inlet and 5/16" barb outlet.

Hose and additional fittings sold separately. MSD pump requires the use of 5/16" high pressure rubber hose with appropriate fuel injection hose clamps for the pressure side of the pump.

Holley 0-4412CT Circle Track 500 CFM 2 Barrel Carburetor
Holley 0-4412CT Circle Track 500 CFM 2 Barrel Carburetor
x
            This 500cfm 4412CT Holly carb shares the hugely  successful features of the original 4412C but with a couple changes  aimed for circle track cars. The choke has been removed but the horn  remains and has been specially calibrated for circle track use. The  4412C Holley carb is easily the most winningest two barrel carburetor on the market  and comes out of the box ready to run. 

Features:
  • Choke delete
  • Choke horn remains
  • 50cc accelerator pump
  • 1 timed (spark) port, 1 full vacuum, & 1 PCV port
  • The mandated carbs for many oval track racing sanctioning bodies
  • Calibrated specifically for circle track use

"Muscle Car, Air and Fuel Delivery" Page 1 of 25

  • AFCO 10171 Bushing Kit w/ RH Threaded Female Rod End
    AFCO 10171 Bushing Kit w/ RH Threaded Female Rod End
    x
                AFCO Throttle Rod Components
            
  • Aluminum Flare Union Adapter Fitting, Black, -10 AN
    Aluminum Flare Union Adapter Fitting, Black, -10 AN
    x
                

    Aluminum 37° flare AN union fitting. Black anodized finish will give your engine compartment the look you are after.

  • Aeroquip FBM4255 Starlite Crimp Fitting, 150 Degree, -12 AN
    Aeroquip FBM4255 Starlite Crimp Fitting, 150 Degree, -12 AN
    x
                

    Aeroquip's incredible Starlite racing hose and fittings are up to 45% lighter than stainless steel braided hose and reusable fittings. Can be used with fuel, lube and coolants. Working temperature is -45° to +300°F and have a 200 psi working pressure.

    Starlite hose can be used with either crimp style or reusable hose fittings. Crimp style fitting must be used only with Starlite hose and installed by qualified personnel using an Aeroquip ProCrimp 1380 crimping machine.

    There are only two ways to order these fittings and hose:

    1. Bring or mail us your old hose to match.
    2. We will send you the fittings and hose you think will work. You cut the hose to length and send it back to us for crimping.

    Fitting Thread Application Chart (GIF)

  • Aeromotive 18664 Stealth Fuel Cell, 15 Gallon
    Aeromotive 18664 Stealth Fuel Cell, 15 Gallon
    x
                

    Finally, a truly universal system that is built for street rods, drag racing, off-road, autocross, drifting and any other performance application you can think of! This complete unit has all the advantages of an in-tank fuel system; quiet cool operation, ideal fuel pump environments and a serious reduction in installation time and investment. In addition, this system eliminates the risk of fuel pump cavitation due to hard cornering, launching or braking thanks to innovative baffling built into each tank.

    • Includes Stealth 340 LPH in-tank fuel pump
    • Works with both carbureted and EFI systems
    • Return line provisions
    • Two AN8 vents with rollover valves
    • Universal 0-90 Ohm fuel level sender
    • Standard 12-bolt flush mount lid assembly
    • Natural aluminum finish
    • Ready to go simple installation

    Fuel Pump Flow Chart (GIF)

  • Edelbrock 1413 Performer 4 Barrel Carburetor, 800 CFM, Electric Choke
    Edelbrock 1413 Performer 4 Barrel Carburetor, 800 CFM, Electric Choke
    x
                Please view the product's page for more information
            
  • Aeromotive 11140 340 Stealth Fuel Pump, Centered Inlet
    Aeromotive 11140 340 Stealth Fuel Pump, Centered Inlet
    x
                

    The Aeromotive 340 Stealth Fuel Pump is a high-output, in-tank, electric fuel pump that fits most popular EFI applications. It is a compact, lightweight pump that bolts into many existing hanger assemblies.

    What sets the 340 Stealth Pump apart is its superior flow throughout a wide pressure range. Compared to other popular aftermarket pumps, at 40 psi the 340 boasts more than 340 lph. That’s over 30% more flow, making it ideal for applications requiring more flow while retaining the factory lines and mounting provisions available in the OE configuration. The 340 is also perfect for use as a universal replacement for applications that require more flow to support forced air power adders such as turbo and supercharged applications.

    • Fits most vehicles where popular aftermarket pumps are applicable
    • Designed for in-tank use only
    • Can be used in carbureted or EFI applications
    • Turbine pump mechanism increases durability and can be used in pulse modulated applications

    910-11140 Instructions (PDF)

  • Lokar XSRK-4001 Black Stainless Steel Carburetor Bracket
    Lokar XSRK-4001 Black Stainless Steel Carburetor Bracket
    x
                

    Stainless bracket mounts to rear of Holley, Edelbrock, AFB, Quadrajet, Demon, and In-Line Dual Quads.  Design provides improved clearance on Edelbrock carbs. Design includes tension screw to prevent bracket from movement under extreme pressure on a kickdown cable, such as with a 700-R4 transmission.

    • Mounts to rear of Holley, Edelbrock, AFB, Quadrajet, Demon, and In-Line Dual Quads
    • Stainless steel
    • Improved clearance on Edelbrock carbs
    • Includes tension screw to prevent bracket movement under extreme pressure

    49104001 Installation Instructions (PDF) 

  • Waterman 935566D Dash Mount Fuel Shut Off Valve, -6 AN
    Waterman 935566D Dash Mount Fuel Shut Off Valve, -6 AN
    x
                Dash mount is AN6 male with offset style handle. Fuel cell ball valve   mounts in plate. Required for many  Sprint cars. They are designed to be  plumbed inline and mount close to the driver.
    • Engineered specifically for sprint car applications
    • -6 AN male to male fuel shut off valve
    • Designed to be plumbed inline and mount close to the driver
  • Speedway 90 -12 AN Flare to 1/2 Inch NPT Pipe Adapter Fitting
    Speedway 90 -12 AN Flare to 1/2 Inch NPT Pipe Adapter Fitting
    x
                

    Many street rodders find that red or blue anodized aluminum AN hose fittings look too racy on their cars, but standard steel versions are just too plain. Speedway offers a great looking alternative with these nickel plated aluminum hose fittings and adapters. Lighter and more affordable than stainless steel, these electoless nickel plated aluminum pieces combine great corrosion resistance with a neutral color and classy appearance.

    Aluminum pipe thread to 37° AN adapter fitting with a 90° bend.

    Fitting Thread Application Chart (GIF)

  • Black Straight -12 AN Flare to 1/2 Inch NPT Pipe Adapter Fitting
    Black Straight -12 AN Flare to 1/2 Inch NPT Pipe Adapter Fitting
    x
                

    These straight flare adaptors connect 1/2" pipe to straight -12 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Black finish will give your engine compartment the look you are after.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fitting
    • -12 AN to 1/2" aluminum pipe
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Black anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Russell Performance 641605 LS/Hemi EFI Fuel System Retrofit Kit
    Russell Performance 641605 LS/Hemi EFI Fuel System Retrofit Kit
    x
                

    This fuel pump kit provides a complete electronic fuel system for GM LS-series and Chrysler 5.7 Hemi engine swaps in muscle cars, street rods and off-road vehicles. Kit features an Edelbrock EFI fuel pump, regulator/filter, relay, Russell Pro Flex hose, an assortment of silver and black AN hose end fittings, and all mounting hardware. When using with OEM fuel tank sending units, an additional adapter to -6 male AN is required.

    • For GM/Chevy LS and Chrysler 5.7 Hemi engine swaps into older non-EFI vehicles
    • Includes Edelbrock Electric Fuel Pump # 3594
    • Includes Edelbrock Fuel Pressure Regulator
    • Returnless Fuel System
    • Supports up to 450 HP
  • Aluminum Flare Union Adapter Fitting, Blue, -12 AN
    Aluminum Flare Union Adapter Fitting, Blue, -12 AN
    x
                

    Aluminum 37° flare AN union fitting. Blue anodized finish.

    Fitting Thread Application Chart (GIF)

  • Aluminum Tee Flare Adapter Fitting, Black, -12 AN
    Aluminum Tee Flare Adapter Fitting, Black, -12 AN
    x
                

    Aluminum tee adapter for 37° AN flared fittings. Black anodized finish will give your engine compartment the look you are after.

    Fitting Thread Application Chart (GIF)

  • 1970-74 Challenger / Cuda Fuel Sending Unit, 3/8 Inch Outlet
    1970-74 Challenger / Cuda Fuel Sending Unit, 3/8 Inch Outlet
    x
                These quality fuel sending units are designed as  replacements for 1970-74 Dodge Challenger & Plymouth Cuda.  Will work with factory  style fuel level gauges.
    • 70-74 CHALLENGER & CUDA
    • 3/8" OUTLET
    • OEM Replacement fuel sender/pickups
    • Designed for use with factory fuel level gauge

    LH/RH Swing Guide (Link)

    Ohms Chart (Link)

  • Socketless Reusable Push-On Hose End for -8 AN Fitting, 45 Degree
    Socketless Reusable Push-On Hose End for -8 AN Fitting, 45 Degree
    x
                

    45° push-on style steel hose ends for use with AN fittings. Special construction assures a tight, leak-proof connection with maximum operating pressures up to 350 psi. Covers a wide variety of automotive fluid conveying applications, including air, water, gasoline, and fuel and lubricating oils. 

    Socketless Push-On Application Chart (GIF)

    Socketless Push-On Assembly (GIF)

  • Holley 0-80670 Avenger 670 CFM 4 Barrel Carburetor, Electric Choke
    Holley 0-80670 Avenger 670 CFM 4 Barrel Carburetor, Electric Choke
    x
                

    The Holley Street Avenger Model 4150 four barrel carb is the ultimate vacuum secondary street performance upgrade. This 4 barrel carb is street ready right out of the box and features a calibrated electric choke, air and fuel adjustments and built in fuel filters. There are clear sights for easy float adjustments, adjustable vacuum secondaries and four vacuum ports. Plus it has a million mile power valve, is 100% wet flow tested and includes fittings.

    • No Trouble quick change vacuum secondaries - up to 6% more acceleration or 5% better fuel economy with simple spring change (springs included) 
    • Vacuum secondaries allow use on wide variety of vehicles
    • Tuneable fuel metering system
    • Dual feed fuel inlet
    • 1 timed (spark) port, 2 full vacuum, and 1 PCV port
    • Ford A/T kickdown, does not work with A.O.D. transmissions
    • Calibrated for monster low-end torque, awesome acceleration, & unmatched top-end horsepower
    • Bolt on & go design
    • Electric choke

    Holley 670 CFM 4 Barrel Carburetor Installation Instructions (PDF)

  • Aeroquip FCE1524 Nickel 45 Deg Push-On Hose Socketless Fitting, -10 AN
    Aeroquip FCE1524 Nickel 45 Deg Push-On Hose Socketless Fitting, -10 AN
    x
                

    Many street rodders find that red or blue anodized aluminum AN hose fittings look too racy on their cars, but standard steel versions are just too plain.

    Speedway offers a great looking alternative with these nickel plated aluminum hose fittings and adapters from Aeroquip. Lighter and more affordable than stainless steel, these electoless nickel plated pieces combine great corrosion resistance with a neutral color and classy appearance.

    Socketless Fitting Application Chart (GIF)

  • Mikise Power Pic Filter Cleaner Spout
    Mikise Power Pic Filter Cleaner Spout
    x
                

    New economy air filter cleaner to clean your air filter from the inside out.  Hooks to a standard garden hose to direct multiple high pressure sprays streams where needed.

    • Clean your air filter from the inside out
    • Hooks to a standard garden hose
  • Speedway Holley Mechanical Fuel Pump Fuel Line Kit
    Speedway Holley Mechanical Fuel Pump Fuel Line Kit
    x
                

    This pump-to-carb fuel line kit will get you the -8 AN hose, hose end fittings and mechanical fuel pump fitting if required. Choose from push-on steel or aluminum fittings with blue hose, or aluminum fittings with stainless steel braided hose. Comes with -8 AN hose only.

    Fitting sizes listed indicate fuel pump outlet fitting size.

    Style Choice Guide:

    • ALU - aluminum fittings with blue hose
    • SS  - aluminum fittings with stainless hose
    • STL - steel fittings with blue hose 
  • Flamed Billet-Style Oval Air Cleaners
    Flamed Billet-Style Oval Air Cleaners
    x
                

    Theses highly polished aluminum air cleaners have the look of billet without the expense. Available with flame top.

    Measures 3" high, 8-3/8" wide. Fits 5-1/8" single quad air horns.

  • Edelbrock Big Block Chevy Dual Quad Set-Up, Rectangular Port
    Edelbrock Big Block Chevy Dual Quad Set-Up, Rectangular Port
    x
                

    There is nothing sweeter looking or sounding than a dual quad on a Chevy! This one kit gets you two manual choke Edelbrock carbs, an Edelbrock unpolished intake manifold, fuel line and special progressive linkage. Just add a suggested air cleaner to finish your installation.

    • 1500-6000 RPM
    • Will clear HEI distributors
    • Will not fit tall-deck truck blocks
    • Has 6-7/16" carb centers

    Overall Height from the bottom of the intake to the top of the air cleaners below:

    325-4237: 11.795"

    325-1235: 11.272"

    325-4119: 12.965"

    Height from bottom of intake to carb mounting surface: 4.899"

    • Port exit dimensions:  1.66" x 2.30

     

  • Aeroquip FBM4043 Hose End Coupler Fitting, 120 Degree, Blue/Red, -8 AN
    Aeroquip FBM4043 Hose End Coupler Fitting, 120 Degree, Blue/Red, -8 AN
    x
                

    Aeroquip reusable hose ends are easier to install than cutter-style fittings and are more user-friendly.  With their compression-style design, they can be reused without damaging the fitting, and the nipple pilot prevents damage to the inner tube.  Their one-piece design allows for improved flow and eliminates two potential leak points (brazed joints).  They're available in red/blue anodized finishes.

    • 120 Degree 
    • Aluminum
    • Hose End Size: -8 AN
    • Fitting Style: Reusable non-swivel
    • Adapter Size: -8 AN
    • Adapter Attachment: Female threads
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • Unique taper design ensures easy assembly
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Accepts a variety of lightweight aluminum AN style adapters & fittings
    • Available in Blue/Red corrosion resistant finish

    Fitting Thread Application Chart (GIF)

  • Aluminum -12 AN Female to -8 AN Male Reducer Fitting
    Aluminum -12 AN Female to -8 AN Male Reducer Fitting
    x
                

    Aluminum female to male adapter for 37° AN fittings. Blue anodized finish.

    Fitting Thread Application Chart (GIF)

  • Sure Seal Air Cleaner Base Only, 14 Inch
    Sure Seal Air Cleaner Base Only, 14 Inch
    x
                

    Speedway's Sure Seal air cleaner base is manufactured from spun aluminum. Fits Holley carbs. Uses standard 14" diameter filters, sold separately. Minimum filter height required is 4".

    • Base has a 1-1/2" drop
    • Distance from the carb neck to top with .5" spacer and 4" filter = 4.25"

     

  • Fuelab 52501-1 EFI Fuel Pressure Regulator, 25-90 PSI
    Fuelab 52501-1 EFI Fuel Pressure Regulator, 25-90 PSI
    x
                

    Gasoline, methanol, ethanol, and dieselfuel compatible for fuel injected applications. Accepts port style and non-port style union fittings without interference. Also features two 1/8” NPT gauge ports for an external pressure gauge and pressure reference. Fine thread pitch on adjustment screw for precise pressure adjustment.

    • Includes stainless steel mounting bracket
    • One -6AN inlet and one -6AN return port in-line
  • Aluminum Straight Thread Fitting Plug, Black, -8 AN
    Aluminum Straight Thread Fitting Plug, Black, -8 AN
    x
                

    Aluminum male straight thread plug with O-ring seal for AN fitting. Black anodized finish.

    Fitting Thread Application Chart (GIF)

  • Black 45 Degree -8 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    Black 45 Degree -8 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    x
                

    Aluminum pipe thread to 37° AN flare adapter fitting with a 45° bend. Black anodized finish will give your engine compartment the look you are after.

    Fitting Thread Application Chart (GIF)

  • Speedway Washable Air Filter Element, 14 x 5 Inch
    Speedway Washable Air Filter Element, 14 x 5 Inch
    x
                Why keep buying paper elements when this one could last a lifetime? These filter elements feature a multi-layer cotton gauze material which is 100% washable and reusable. Use appropriate filter cleaner and filter oil at every service.
            
  • Edelbrock 2921 Victor Jr. Ford 302 Intake Manifold
    Edelbrock 2921 Victor Jr. Ford 302 Intake Manifold
    x
                

    The Edelbrock Victor Series intake manifolds have set the standard for quality and performance in the racing industry. The Victor Jr. 302 is designed for Ford 260-289-302 competition engines using modified stock cast iron or aftermarket Windsor-style cylinder heads.

    The Victor Jr. 302 has no rear water crossover. Port exit size at cylinder head is 1.90" x 1.08" with enough extra material to open it up to 2.10" x 1.18".

    325-2921 Instructions (PDF)

  • Big Block Chevy Street Tunnel Ram Kit, Polished Scoop
    Big Block Chevy Street Tunnel Ram Kit, Polished Scoop
    x
                

    Oh baby, this would look cool on your car! This complete B/B Chevrolet  Street Tunnel Ram Kit features the  Edelbrock 2-O manifold designed for use on 396-502 c.i.d. big-block Chevy V8s with large oval-port heads (1975 and earlier). Ideal for lightweight applications such as T-buckets or pro-street cars where low-end torque is not a prime factor. Especially suited to engines using slightly modified or aftermarket cylinder heads (9.5:1 or more compression is advised). Optimum power range is 3500-7500 rpm.

    Includes plain unpolished manifold, two 600 cfm manual choke Edelbrock Perfromer carburetors, polished gasser style scoop with filters, and linkage. Not for the faint of heart!


  • AFCO 10176-24 Throttle Rod, 24 Inch Long
    AFCO 10176-24 Throttle Rod, 24 Inch Long
    x
                
    • 1/4" plated steel rod
    • 1/4" male right hand threads on both ends
    Note: Extra-long thread allows more adjustment
  • Edelbrock 12801 Polished 2-Carb Fuel Block
    Edelbrock 12801 Polished 2-Carb Fuel Block
    x
                

    Edelbrock has reintroduced the vintage cast aluminum fuel blocks for dual, triple and quad carb applications for your hot rod or custom. This fuel log features a single 3/8" NPT inlet and two 1/4" NPT outlets. Each fuel distribution block has four holes for mounting to a firewall.

    Polished finish.

  • Aeromotive 12301 10 Micron Red High Flow Fuel Filter, ORB-10 Ports
    Aeromotive 12301 10 Micron Red High Flow Fuel Filter, ORB-10 Ports
    x
                

    Engineered to support 200-3000 HP, these Aeromotive high flow fuel filters are an inexpensive insurance policy to protect your investment. Filters measure 5.5" long and 2" diameter. Contains -10 AN port fittings on the inlet and outlet. Machined from 6061-T6 aircraft aluminum and anodized for a corrosion resistant show car quality appearance. Ideal for carburetion or fuel injection up to 150psi.

    • High-flow, 10-micron fabric (fine) replaceable element 
    • Flows 2,000 lb/hr with a pressure drop of less than 1 PSI
    • Compact size: 5.5” long x 2” diameter
    • All filter assemblies feature an O-ring for positive sealing in high pressure applications
    • CNC-machined from 6061-T6 aircraft aluminum
    • Bright dip red anodized finish for a corrosion resistant, show car quality appearance

    Note: 10-micron filters may ONLY be used after the fuel pump to protect your injectors or carburetor. Fabric elements not suitable for use in E85 or alcohol applications.

  • K&N Filters 99-0533 Air Filter Oil, Squeeze Bottle
    K&N Filters 99-0533 Air Filter Oil, Squeeze Bottle
    x
                

    K&N Air Filter Oil is the only oil specially formulated to work in combination with the cotton fabric in K&N Filtercharger elements providing a superior air filtration system. When used as directed, it quickly penetrates the filter pleats, where it remains suspended in the cotton fabric. Saturation is maintained until the element is cleaned with K&N Air Filter Cleaner.

    8 Oz. squeeze bottle.


  • Aluminum Flare Fitting Plug, Blue, -8 AN
    Aluminum Flare Fitting Plug, Blue, -8 AN
    x
                

    Aluminum flare plugs. 37° AN.

    Fitting Thread Application Chart (GIF)

  • Aeroquip FCE4035 Nickel Plated -12 AN Hose End Fitting, 90 Degree
    Aeroquip FCE4035 Nickel Plated -12 AN Hose End Fitting, 90 Degree
    x
                

    Many street rodders find that red or blue anodized aluminum AN hose fittings look too racy on their cars, but standard steel versions are just too plain.

    Speedway offers a great looking alternative with these nickel plated aluminum hose fittings and adapters from Aeroquip. Lighter and more affordable than stainless steel, these electoless nickel plated pieces combine great corrosion resistance with a neutral color and classy appearance.

    These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a nickel-plated finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617312).

    • -12 AN Aluminum
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Nickel corrosion resistant finish

    Fitting Thread Application Chart (GIF)

Goto Previous PagePrevious Page
1 2 3 4 5 ... 25