Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Fittings and Hoses At Speedway Motors

Speedway Motors has hundreds of fuel line, water and oil line fittings and hose in stock and ready to ship! Plumb your race car, street rod, classic truck, or muscle car with fittings from top brands like Aeroquip, AFCO and Fragola. We stock everything from anodized AN fittings and power steering fittings to high-pressure stainless steel braided line, as well as all the tools needed to assemble and install them.

"Fittings and Hose, Fittings" Page 1 of 8

  • Inverted Flare Thread Nuts for 3/16 Inch Tubing, 3/8-24
    Inverted Flare Thread Nuts for 3/16 Inch Tubing, 3/8-24
    SKU-91031820
    x
                

    Steel 3/8"-24 IFM thread nuts for 3/16" brake line when double flared to 45°.

  • AN Fitting Plug, -8 AN
    $4.99
    AN Fitting Plug, -8 AN
    SKU-54523804
    x
                These AN fitting plugs have always been hard-to-find items. Plugs are used when sealing spare race engines against dirt and water during transportation and storage. Each plug is reusable. Use on oil, fuel, or coolant lines. Four plugs per package.
            
  • Black 45 Degree Socketless Push-On Hose End, -8 AN
    Black 45 Degree Socketless Push-On Hose End, -8 AN
    SKU-62020101
    x
                

    Black socketless push-on hose end fittings will give your engine compartment the look you are after. 45 degree fittings in multiple sizes.  For use with 37 degree flared ends.

  • Speedway Full Flow Swivel Hose End Fitting, 45 Degree, Red/Blue -12 AN
    Speedway Full Flow Swivel Hose End Fitting, 45 Degree, Red/Blue -12 AN
    SKU-6201012
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then red and blue anodized to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 45 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -12 AN
    • 45 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Red/Blue corrosion resistant finish

    Full Swivel Application Chart (GIF)

  • AN16 Fitting Caps, 4/pk
    $5.99
    AN16 Fitting Caps, 4/pk
    SKU-54523811
    x
                These AN fitting caps have always been hard-to-find items. Caps are used when sealing spare race engines against dirt and water during transportation and storage. 

    Each cap is reusable. Use on oil, fuel, or coolant lines. Four caps per package.

  • Speedway Full Flow Swivel Hose End Fitting, Straight, Anodized, -8 AN
    Speedway Full Flow Swivel Hose End Fitting, Straight, Anodized, -8 AN
    SKU-62010031
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then black anodized to give them a new sleek look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a straight design and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -8 AN female to push-on adapter
    • Straight style fuel line hose connector/coupler
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Black corrosion resistant finish

    Full Swivel Application Chart (GIF)

  • 3/8 Inch-24 IFF Each Port with Bracket, Chrome Adapter Tee
    3/8 Inch-24 IFF Each Port with Bracket, Chrome Adapter Tee
    SKU-91031839
    x
                IFF TEE male and female adapters
            
  • Threaded Aluminum Weld Bung Fitting, 1/8 Inch NPT Female
    Threaded Aluminum Weld Bung Fitting, 1/8 Inch NPT Female
    SKU-6176801
    x
                

    We offer these premium-quality weld-in bungs for a variety of uses. They're CNC-machined from solid aluminum and are great for oil or fuel tanks, radiators, valve covers, manifolds, and rear axle housings.

    Aluminum female pipe thread weld bung fitting.

    Threaded Aluminum Weld Bung Fitting

    • 1/8 Inch NPT

    Fitting Thread Application Chart (GIF)

     

  • Goodridge AN921-08D 90 Deg High-Flow O-Ring -8 AN Hose to Port Fitting
    Goodridge AN921-08D 90 Deg High-Flow O-Ring -8 AN Hose to Port Fitting
    SKU-6177025
    x
                

    Goodridge high-flow 90° bend O-ring port adapter fitting for 37° AN flare. Blue anodized finish.

    Fitting Thread Application Chart (GIF)

  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Black, -10 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Black, -10 AN
    SKU-62010181
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then black anodized to give them a new sleek look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -10 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Black corrosion resistant finish

    Full Swivel Application Chart (GIF)

  • AN8 Fitting Caps, 4/pk
    $4.99
    Product Rating: 5.00 Stars
    AN8 Fitting Caps, 4/pk
    SKU-54523805
    x
                These AN fitting caps have always been hard-to-find items. Caps are used when sealing spare race engines against dirt and water during transportation and storage. 

    Each cap is reusable. Use on oil, fuel, or coolant lines. Four caps per package.

  • AN Fitting Plug, -6 AN
    $4.99
    AN Fitting Plug, -6 AN
    SKU-54523802
    x
                These AN fitting plugs have always been hard-to-find items. Plugs are used when sealing spare race engines against dirt and water during transportation and storage. Each plug is reusable. Use on oil, fuel, or coolant lines. Four plugs per package.
            
  • Speedway Replacement Nitrile O-Rings for -4 AN Fittings, Pack/10
    Speedway Replacement Nitrile O-Rings for -4 AN Fittings, Pack/10
    SKU-6173473
    x
                

    Speedway replacment "Nitrile 1" AN fitting O-rings are designed for standard fuel or oil applications.

    Bag of 10 O-rings.

    Fitting Thread Application Chart (GIF)

  • Jiffy-Tite 52312 Quick Connect Fluid Fittings, -12 AN Female Socket
    Jiffy-Tite 52312 Quick Connect Fluid Fittings, -12 AN Female Socket
    SKU-46852312
    x
                

    Tested and proven to have a 100% leak proof seal at 200 psi and 350° F. Made of aluminum, these Jiffy-Tite valved disconnects are compact, durable, and corrosion resistant. High-flow valve technology in the plug and socket assembly automatically interrupts the flow of fluid when disconnected by hand. Not intended for brake systems.

    Select a socket and a plug to make a complete coupler. AN sizes are 37° for mating with existing hose ends or bungs.

    See Application tab for intended use on each disconnect/plug.

    Jiffy-Tite Flow Specs (Link)

  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Nickel, -6 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Nickel, -6 AN
    SKU-62010160
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then given a nickel finish to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -6 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a corrosion resistant nickel finish

    Full Swivel Application Chart (GIF)

  • AN Fitting Plug, -4 AN
    $4.99
    AN Fitting Plug, -4 AN
    SKU-54523800
    x
                These AN fitting plugs have always been hard-to-find items. Plugs are used when sealing spare race engines against dirt and water during transportation and storage. Each plug is reusable. Use on oil, fuel, or coolant lines. Four plugs per package.
            
  • Socketless Reusable Push-On Hose End for -4 AN Fitting, 90 Degree
    Socketless Reusable Push-On Hose End for -4 AN Fitting, 90 Degree
    SKU-1061241
    x
                

    Push-on style with 90° steel hose ends for use with AN fittings. Special construction assures a tight, leak-proof connection with maximum operating pressures up to 350 psi. Covers a wide variety of automotive fluid conveying applications, including air, water, gasoline, and fuel and lubricating oils.

    Socketless Push-On Application Chart (GIF)

    Socketless Push-On Assembly (GIF)

    Fitting Thread Size Guide (GIF)

    NPT Thread Size Chart (GIF)

  • Aeroquip FBM4435 Black Hose End Coupler Fitting 90 Degree Angle -12 AN
    Aeroquip FBM4435 Black Hose End Coupler Fitting 90 Degree Angle -12 AN
    SKU-61710191
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a black anodized finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617312).

    • -12 AN 
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • Unique taper design ensures easy assembly
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Accepts a variety of lightweight aluminum AN style adapters & fittings
    • Available in a Black corrosion resistant finish

    90° Full Flow Ends come in sizes of AN6, AN8, AN10 and AN12.

    Fitting Thread Application Chart (GIF)

  • Jiffy-Tite 21506P Quick Disconnect Fluid Fittings, -6 AN Push Lock
    Jiffy-Tite 21506P Quick Disconnect Fluid Fittings, -6 AN Push Lock
    SKU-46821506P
    x
                

    Tested and proven to have a 100% leak proof seal at 200 psi and 350° F. Made of aluminum, these Jiffy-Tite valved disconnects are compact, durable, and corrosion resistant. High-flow valve technology in the plug and socket assembly automatically interrupts the flow of fluid when disconnected by hand. Not intended for brake systems.

    Select a socket and a plug to make a complete coupler. AN sizes are 37° for mating with existing hose ends or bungs.

    See Application tab for intended use on each disconnect/plug.

    Jiffy-Tite Flow Specs (Link)

  • 45 Degree Socketless Push-On Hose End, Nickel, -12 AN
    45 Degree Socketless Push-On Hose End, Nickel, -12 AN
    SKU-6201525
    x
                

    45° socketless push-on hose ends for 37° fittings.

    Nickel Finish 

    Socketless Push-On Hose End Application Chart (GIF)

  • Speedway Full Flow Swivel Hose End Fitting, 45 Degree, Red/Blue -10 AN
    Speedway Full Flow Swivel Hose End Fitting, 45 Degree, Red/Blue -10 AN
    SKU-6201011
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then red and blue anodized to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 45 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -10 AN
    • 45 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Red/Blue corrosion resistant finish

    Full Swivel Application Chart (GIF)

  • Speedway Replacement EPR2 O-Rings for -4 AN Fittings, Pack/5
    Speedway Replacement EPR2 O-Rings for -4 AN Fittings, Pack/5
    SKU-6173463
    x
                

    Speedway replacment "EPR2" AN fitting O-rings are for use with alcohol or nitro fuels.

    Bag of 5 O-rings.

    Fitting Thread Application Chart (GIF)

  • Speedway Full Flow Swivel Hose End Fitting, 45 Degree, Nickel, -8 AN
    Speedway Full Flow Swivel Hose End Fitting, 45 Degree, Nickel, -8 AN
    SKU-62010100
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then given a nickel finish to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 45 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -8 AN
    • 45 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a corrosion resistant nickel finish

    Full Swivel Application Chart (GIF)

  • Aeroquip FBM4033 Full Flow Hose End Coupler Fitting, 90 Degree, -8 AN
    Aeroquip FBM4033 Full Flow Hose End Coupler Fitting, 90 Degree, -8 AN
    SKU-6171017
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a blue/red anodized finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617308).

    • -8 AN 
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • Unique taper design ensures easy assembly
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Accepts a variety of lightweight aluminum AN style adapters & fittings
    • Available in Blue/Red corrosion resistant finish

    90° Full Flow Ends come in sizes of AN4, AN6, AN8, AN10, AN12 and AN16.

    Fitting Thread Application Chart (GIF)

Goto Previous PagePrevious Page
1 2 3 4 5 ... 8