Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Electrical, Lighting and Body At Speedway Motors

At Speedway Motors, we believe in a having a good-looking set of tail lights because with our performance parts, that's all the compeition usually sees! We have the largest selection of headlights, auxiliary lights and third brakes lights, plus the wiring harnesses to make it all work. We'll help you light up the night - you just focus on lighting up those tires!

Featured Products
Two Post Battery Disconnect Switch
Two Post Battery Disconnect Switch
x
            Remote battery disconnect switch for safety and theft protection. A battery kill switch is required for use with alternators by the NHRA. Battery shut off switch can be remote mounted or where specified for saftey and  convenience.
  • 180 amp continuous, 1000 amp instantaneous
  • Die cast lever
  • Fits panel through 3/16" thick

910-64500 Instructions (PDF)

Heavy Duty Turn Signal Switch
Heavy Duty Turn Signal Switch
x
            

For early autos not equipped with right and left turn signals. Chrome plated finish. Switch works with 6 or 12 volt systems. Includes wiring diagram. Clamps to any steering column with included stainless hose clamp. Switch has four-way flashers and does not self cancel.

You will need to purchase a three-prong flasher to use with this switch (part number 910-64046). For LED light applications, you will also need a LED dummy load resistor (part number 910-03030).

910-62860 Instructions (PDF)

Black Dietz Type Headlights, Standard Bulb
Black Dietz Type Headlights, Standard Bulb
x
            

Our universal fit Deitz-type 7" headlights feature black painted housings with chrome rings. Has a 12 volt sealed beam bulb with both high & low beams. "Drilled" mounting stud measures 1/2"-13. The pre-wired plug has 3 wires with 6" leads.

1928-1931 Ford Model A Stainless Tail Lights
1928-1931 Ford Model A Stainless Tail Lights
x
            

Polished stainless steel housing with glass lenses. An excellent replacement or addition to your Model 'A' Ford. Left tail light has lenses on the bottom to illuminate a license plate. Choose left or right. 12 volt operation.

  • 3.851" diameter
  • 3" depth
  • 3.851" height
  • 1-3/4" mount 

Wire colors:

  • Housing - Ground
  • Tail - Black
  • Stop - Green

These tail lights have two bulbs in them that are of a single filament style. 

Lokar SP-1500U GM Speedometer Drive Cable Kit, Black
Lokar SP-1500U GM Speedometer Drive Cable Kit, Black
x
            

The finishing touch to your mechanical (cable-drive) speedometer installation in your GM or Mopar. Includes a 7 ft. long glossy black vinyl housing and inner cable (you trim to length) with billet aluminum ends, and instructions.

Works with all cable-drive aftermarket and original equipment speedometers that have a male 5/8"-18 thread connection. Has a 7/8"-18 end for the transmission.

Universal Headlight Switch With Hi/Low
Universal Headlight Switch With Hi/Low
x
            

This headlight switch has four positions. In is off, out one notch is park lights, out another notch is lows beams, and all the way out is high beams. Screw type terminals. 3/8" mounting hole.

910-80154 Instructions (PDF) 

LED Cat Eye Tail Light
$39.99
Product Rating: 4.73 Stars
LED Cat Eye Tail Light
x
            

This 12-volt, 12-LED tail light can be used as a stop/turn/tail or just use as a third stop light. Measures 7.25" long x 1-50" tall x .730" thick with a chrome bezel. Light is flat on the back side and comes with a mounting gasket.

10-32 mounting bolts (not) included.

LED Cat Eye Tail Light Installation Instructions (PDF) 

Power Window Kit
$149.99
Product Rating: 4.75 Stars
Power Window Kit
x
            
  • Kit for 2 doors
  • Works for all flat glass windows
  • Straight up and down travel only
  • 6"-24" Glass height
  • Includes: Switches, wiring and crossover kit

Instructions (PDF)

"Electrical, Lighting and Body" Page 1 of 20

  • AFCO 85053B Starter Switch Panel with Lights, 4-1/8 x 5-7/8 Inch
    AFCO 85053B Starter Switch Panel with Lights, 4-1/8 x 5-7/8 Inch
    x
                

    AFCO starter switch panels are for standard ignitions.

    Wiring Instructions (PDF)

  • Lokar SG-6009 Chrome Dimmer Switch Cover, Chevy/Ford
    Lokar SG-6009 Chrome Dimmer Switch Cover, Chevy/Ford
    x
                Brighten up that old dimmer switch with one of these new dimmer switch covers from Lokar!  Made from steel and feature a beautiful chrome finish and a textured rubber pad. 
            
  • DEi 030305 Lite N Boltz LED Bolts, Amber
    DEi 030305 Lite N Boltz LED Bolts, Amber
    x
                

    Available in five different colors, these LED stainless steel button head bolts can be used for anything imaginable. These can be used on the interior or exterior and are compact enough to put anywhere. Sold per pair and have 5/16"-18 x 3/4" threads. 12 volt. Has a 9/16" O.D.

    Useful as:

    • Map and gauge lights
    • Indicator signals
    • Step illumination
    • Engine compartment lighting
    • Running boards
    • Truck bed rails
    • Dashboard accent lights

    Product FAQ's (PDF)

  • Modern Driveline Reverse Switch Harness for GM T5 and T56 Transmissions
    Modern Driveline Reverse Switch Harness for GM T5 and T56 Transmissions
    x
                

    These harnesses for transmission neutral safety switch/reverse light switches are designed for use with GM T5 and T56 transmissions.

    • Factory style
    • For GM T5 and T56 transmissions

     

  • 1954 Chevy Park Light Lens, Amber
    1954 Chevy Park Light Lens, Amber
    x
                These amber parking light lens for 1954 Chevy passenger cars feature  original   style lens pattering. They fit the factory housing    and are  a direct   replacement for your old damaged or missing park light    lens. 
    • Amber plastic lens with original style lens patterning 
    • Fits factory housing
    • Left or Right Side
    • Fits All Passenger Cars
    • Sold each
  • 1933-34 Ford Car, 1935-37 Ford Truck Headlight Mount Pads
    1933-34 Ford Car, 1935-37 Ford Truck Headlight Mount Pads
    x
                

    These headlight mount gasket pads fit '33-'34 Ford passenger cars as well as '35-'37 Ford pickup trucks.  They are rubber construction and are not visible when properly installed.  Use these rubber gaskets to ensure a tight seal.

    • OEM replacements
    • 1933-'34 Ford passenger cars and 1935-'37 Ford pickups
    • Rubber construction
    • Sold as a pair
  • Halogen Tail Light Bulbs, 1157 Offset Mounting Pins
    Halogen Tail Light Bulbs, 1157 Offset Mounting Pins
    x
                

    Those other super bright, super high powered tail light bulbs may be easy to see, but they also generate enough heat to discolor your lens and burn the paint.

    Halogen tail light bulbs are brighter than standard bulbs, but use less energy, which means they burn cooler. 12 volt only.

    This bulb is shorter than a 1157 bulb and measures only 1-3/4" from bottom to end of the tip. From the pin to tip is 1-1/2".



     

  • Tall Model T Cowl-Tail Lights, Black
    Tall Model T Cowl-Tail Lights, Black
    x
                

    Features a 12 volt dual element bulb and can be used as a tail light or a cowl light. 9-1/2" tall with 3" diameter lens. Specify red or amber lens.

    Note: Mount bracket is NOT included. Lens must be secured in place with silicone (see Instructions).

    Cowl Light Installation Instructions (PDF)

  • 1932 Ford Stainless Tail Lights
    From: $29.99
    Product Rating: 4.67 Stars
    1932 Ford Stainless Tail Lights
    x
                

    These are an exact duplicate of the original 1932 Ford glass lens tail lights. Left light has a lens to illuminate license plate. Choose left or right.

    • 12 volt bulb
    • Highly polished stainless steel housing & rim
    • Cloth braided wire loom
    • Stainless steel screws
    • Glass red lens
    • 3-7/8" diameter, 2-3/8" depth
    • 2-11/16" overall depth (includes the wire retainer on the back of the lamp)

     

  • 1968 Belair/Biscayne LED Tail/Stop Lights
    1968 Belair/Biscayne LED Tail/Stop Lights
    x
                

    Face it, it's hard to see those tail lights on older cars. Now is the time to change out those broken or faded tail lights for new LED versions. 

    • 40 Super Bright LEDS
    • Polycarbonate Lens
    • Epoxy Coated, Fully Sealed Electronics, 1157 Plug
    • Solid State Circuit Boards Designed for 7.7 - 14.0 VDC

     

  • Stewart Warner 279B-F Deluxe Electrical Oil Pressure Sender
    Stewart Warner 279B-F Deluxe Electrical Oil Pressure Sender
    x
                

    Designed to make sure that you get fast, accurate information from your Stewart Warner gauges. 

    • 1/8-27 NPT
    • Electrical
    • Designed to be used with 90° sweep gauges
  • 1949-1950 Chevy Chrome Tail Light Bezel with Red Reflector
    1949-1950 Chevy Chrome Tail Light Bezel with Red Reflector
    x
                These tail light bezels for 1949-1950 Chevy passenger cars replicate those of the original. They feature a chrome plated finish and the original style red reflectors. 
    • Chrome plated steel bezel
    • Has original style red reflector with "GUIDE" script
    • Duplicate of original
    • Left or Right Side
    • Fits All Passenger Cars
  • American Autowire 37788 1955 Chevy OEM Style Turn Signal Switch
    American Autowire 37788 1955 Chevy OEM Style Turn Signal Switch
    x
                

    If you're still running the stock column in your 1955 Chevy car, you'll probably need one of these OEM style turn signal switches.  They come complete with the male connector body.

    • 1955 Chevrolet passenger car
    • OEM style replacement
    • Complete with male connector body

     

  • AFCO 85293 Warning Light, Oil Temp.
    AFCO 85293 Warning Light, Oil Temp.
    x
                

    These lights allow the driver to maintain focus on the race.

    Wiring Instructions (PDF)

  • Fuse Block for Glass Fuses
    $9.99
    Product Rating: 5.00 Stars
    Fuse Block for Glass Fuses
    x
                

    Allows easy installation of extra fuses or for use in basic electrical systems. Accepts 7 glass fuses. Also included is two connector strips, one ties three fuses to a common power source and one ties two fuses to a common power source.

  • Lokar CC-1600U Carbureted Cruise Control Cable, Black
    Lokar CC-1600U Carbureted Cruise Control Cable, Black
    x
                
    • Lokar cruise control cable is for use with Rostra control kits. Kit includes 4 foot stainless outer housing designed with a specialty extruded liner for extended life of the cable and 5 feet of stainless inner wire, which replaces black plastic cable in Rostra kits. Cables are u-cut-to-fit inside and outside of the firewall. All billet aluminum fittings, stainless hold down clip and mounting bracket. Mount cable to carburetor with Lokar's stainless carburetor bracket and return springs.
    • For Use w/Rostra Control Kits
    • Stainless Housing
    • 5 in. Stainless Inner Wire/4 in. Outer Housing
    • U-Cut-To-Fit Inside And Outside Of Firewall
    • Billet Aluminum Fittings
    • Incl. Hold Down Clip/Mounting Bracket
    • Made In The U.S.A.
    • Lifetime Warranty
  • Speedway 7 Inch Fluted Replacement Headlights w/ Amber Turn Signal
    Speedway 7 Inch Fluted Replacement Headlights w/ Amber Turn Signal
    x
                

    Speedway's 7" replacement Fluted H4 Headlights allow you to have "the look" with out breaking the bank. Features a chrome plated plastic reflector with a glass lens and an "amber" turn signal lens. Includes a H4 Halogen bulb.

    These headlights have a separate 94-style single filament bulb which can be used as a turn signal or a running lamp (not both). 

    • 6-5/8" headlight O.D.
    • Wiring pigtail for turn/running light is included
    • Wiring pigtail for headlight NOT included
    • Uses common 3-prong headlight plug-in

    Headlight Wiring Chart (GIF)

    Installation Instructions (PDF)  

  • Stewart Warner 82623B GM Sender for Wings Electronic Speedometer
    Stewart Warner 82623B GM Sender for Wings Electronic Speedometer
    x
                

    This sending unit for electronic speedometers has a .894" (7/8”) female attachment nut to attach it to the transmission or out-drive unit.  This is similar to the female threaded ring on mechanical speedometer cables. Most customers will need to purchase part number 66582629, square drive tip, to attach this sender to a GM transmission.

  • 1928-29 Dropped Stainless Headlight Bars
    1928-29 Dropped Stainless Headlight Bars
    x
                1928-1929 Dropped style stainless steel headlight bars. Polished. 

    Top width (flange tip to flange tip) 42-1/2"
    Bottom width (flange tip to flange tip) 38-1/2"
  • 1957 Chevy LED Tail Light Conversion Kit
    1957 Chevy LED Tail Light Conversion Kit
    x
                The 1957 Chevy cars were not known to have very bright or visible tail lights. The cure is the addition of LED conversion kits. 

    These replace old 1157 style bulbs with 14 LED bulbs that are much brighter, don't put out much heat and last up to 100,000 hours. Stainless steel hardware and easy 30 minute installation.

    1957 Chevy LED Tail Light Conversion Instructions (pdf)

  • MSD 7990 Dual Ignition Kill Switch
    MSD 7990 Dual Ignition Kill Switch
    x
                

    When running a crank trigger, you now have an option of two base timings. When the track gets slick, just flip the switch to kill some power.

     MSD Rebate (Link)

  • 1928-29 Model A Style Headlights
    1928-29 Model A Style Headlights
    x
                Available in polished stainless steel. 12 volt bulb is mounted behind original style lens. Complete with mounting stud. 9" diameter. Stainless with Halogen bulb. 
            
  • Lokar SP-1503HT Ford Speedometer Drive Cable Kit, Stainless
    Lokar SP-1503HT Ford Speedometer Drive Cable Kit, Stainless
    x
                

    The finishing touch to your mechanical (cable-drive) speedometer installation in your Ford. Kit includes a 7 ft. long braided stainless steel housing and 7' inner cable (you trim to length), billet aluminum fitting ends and instructions.

    Works with all cable-drive aftermarket and original equipment speedometers that have a male 5/8"-18 threaded connection. The transmission end has the standard Ford end with retaining clamp.

  • Lokar SP-1506U Early Ford Speedo Cable Kit w/Ford End, Black Housing
    Lokar SP-1506U Early Ford Speedo Cable Kit w/Ford End, Black Housing
    x
                Premium housing designed with a specially extruded liner for extended life of the cable and billet aluminum fittings. Inner cable and outer housing are "U-Cut-to-Fit". Kit comes complete with all fittings and is available for GM, Ford and Chrysler applications. (Gauges not included)
    Lokar Speedometer Cables are designed to work with most cable driven aftermarket speedometer gauges (such as Auto Meter, Stewart Warner, VDO, Classic Instruments, etc.) or factory speedometer with a 5/8-18 male thread at the speedo.
    Lokar Speedometer Cables are designed to fit into the transmission gear adapter (not supplied in Chevy or Chrysler Lokar Kit). Customer must have the trans end adapter and speedometer gear for all Chevy and Chrysler applications. For Ford applications, the gear adapter is supplied in the Lokar Kit. Customer must supply the speedo gear and speedo gear retainer clip.
    • All Lokar Speedometer Cables are seven feet (7') long
    • Designed to be "U-Cut-to-Fit".
    • Additional length cable in black or stainless housing is available upon request for an additional charge.
    • Must have a 3/4 - 20 female thread at the speedometer
  • 1955 Chevy LED Tail Light Conversion Kit
    1955 Chevy LED Tail Light Conversion Kit
    x
                The 1955 Chevy cars were not known to have very bright or visible tail lights. The cure is the addition of LED tail light conversion kits. 

    These replace old 1157 style bulbs with 14 LED bulbs that are much brighter, don't put out much heat and last up to 100,000 hours. Stainless steel hardware and easy 30 minute installation.

    1955 Chevy LED Tail Light Conversion Instructions (pdf)

  • DEi 030304 Lite N Boltz LED Bolts, Red
    DEi 030304 Lite N Boltz LED Bolts, Red
    x
                

    Available in five different colors, these LED stainless steel button head bolts can be used for anything imaginable. These can be used on the interior or exterior and are compact enough to put anywhere. Sold per pair and have 5/16"-18 x 3/4" threads. 12 volt. Has a 9/16" O.D.

    Useful as:

    • Map and gauge lights
    • Indicator signals
    • Step illumination
    • Engine compartment lighting
    • Running boards
    • Truck bed rails
    • Dashboard accent lights

    Product FAQ's (PDF)

  • Longacre 44611 Flip-Up Start/Ignition Switch Panel w/Pilot Light
    Longacre 44611 Flip-Up Start/Ignition Switch Panel w/Pilot Light
    x
                These high capacity (40 amp at 12 volts) ignition switch panels with aircraft style cover and pilot light are easy to turn off in an emergency from any angle, even with gloves. Will not turn off from vibration. They come pre-wired with high insulation "Fat" wires and soldered terminals with heat shrinked seals.
    • Starter button with weatherproof cover
    • Lightweight aluminum panel
    • Plugs into Longacre wiring harness P/N 44930
    • Ignition Switch:
      • Style:    Toggle
      • Cover:    Aircraft style flip
      • Pilot Light Included:   Yes
      • Rating:    40 amps @ 12 volts
    • Starter Switch:
      • Style:    Push button
      • Cover:    Weatherproof rubber
      • Rating:    15 amps @ 12 volts resistive
    • Panel:
      • Material:    Lightweight aluminum
      • Panel Dimensions:   3-1/2" x 3-1/2"
      • Wiring Included:    Yes
  • Lokar XBAG-6109 Midnight Series Oval Billet Aluminum Dimmer Cover
    Lokar XBAG-6109 Midnight Series Oval Billet Aluminum Dimmer Cover
    x
                
    • Oval Billet Aluminum Dimmer Cover – Brushed
    • Black Anodized Billet Aluminum 
    • Made In The U.S.A.

     

  • Toggle Ignition On Switch
    $9.99
    Product Rating: 4.67 Stars
    Toggle Ignition On Switch
    x
                Toggle switch works great as a kill switch or with other auxiliary equipment. 25 amp SPST switch with rubber boot and on/off plate.
            
  • 1930-31 Ford Model A Dropped Headlight Bar Kit, Stainless
    1930-31 Ford Model A Dropped Headlight Bar Kit, Stainless
    x
                Get everything you need to complete your  dropped headlight bar installation with this convenient kit!  All for  one money saving price.

    Includes:
    • 911-21809 - Stainless Headlight Bar
    • 751-A13130BS - Rubber mounting pads
    • 751-A13130SS - Hardware kit
  • Universal Headlight Mount
    $19.99
    Product Rating: 4.00 Stars
    Universal Headlight Mount
    x
                
    • 5/16" mounting holes 2" center to center
    • 1/2" ID sleeve for light mounting bolt
    • Great for headlights and taillights
    • Use with mounting cups 91061034
  • 1932 Ford Tail Light LED Conversion Lens
    1932 Ford Tail Light LED Conversion Lens
    x
                These direct replacement tail light lenses will convert your 1932 Ford Deuce tail lights to powerful and bright LED lights. Choose left or right sides.
    • 17 Super Bright Red LEDs
    • Drivers side (Left side) includes a 4 LED White License Light (primary picture)
    • Epoxy coated, fully sealed electronics
    • Two 1156 plugs
    • Solid state circuit board for 12V systems 
    1932 Ford LED Tail Light Conversion Instructions (pdf)
  • 1942-1948 Ford Car Tail Lights
    1942-1948 Ford Car Tail Lights
    x
                

    Duplicate of original 1942-1948 Ford passenger car taillights with polished stainless steel housings complete with red glass lens. Uses a single 1157 dual filament bulb (included). Mounting gasket NOT included.

    • Highly polished stainless steel housing & rim
    • Cloth braided wire loom
    • 12 volt bulb
    • Red glass lens
  • 1937-1938 Chevy Blue Dot Tail Light Lens, Passenger Car
    1937-1938 Chevy Blue Dot Tail Light Lens, Passenger Car
    x
                

    These red glass tail light lens are replacements for your 1937-1938 Chevy passenger car.  They feature the classic Lynx-Eye blue dot in the center.

    • Original replacements
    • 1937-1938 Chevy passenger car only
    • Classic Lynx-Eye blue dot in center
    • Red glass lens
    • Sold each
  • Safety Kill Switch
    $19.99
    Product Rating: 4.50 Stars
    Safety Kill Switch
    x
                

    This is the best kill switch we've found! Works with standard ignition only. Water resistant with O-ring shaft seal. Pull on, push off with silver contacts.

    20 amp rating at 12 VDC.

  • Speedway 2005-2006 LS2/4L65E Wiring Harness, Extended
    Speedway 2005-2006 LS2/4L65E Wiring Harness, Extended
    x
                

    Take the fear out of electronic fuel injection! These engine wiring harnesses are designed to make your engine transplant effortless. Each new harness contains in-depth application-specific instruction sheets, clearly marked factory GM connectors, labeled GXL jacketed wire, GM color coding, and pre-fitted corrugated slit loom for an extra value and professional look. All un-needed emissions wiring is eliminated to make the install as simple and reliable as possible.

    2005-2006 LS2/E40 24X Reluctor and 4L65E Transmission

    • Made from premium grade GXL jacketed automotive wire
    • Most wiring is larger gauge than stock application for durability
    • No splices to reduce points of failure
    • All primary grounding is done at the head or block and grounding points are isolated from each other to reduce electrical interference and minimize ground looping
    • Harness wiring matches GM wiring configuration and jacket colors follow GM color coding for easy identification
    • All electrical connectors are made by Delphi or Packard and are direct fit for GM cars and trucks
    • Can be installed to run engine in 20 minutes, but figure 4-6 hours for a professional installation
    • Diagnostic connector or OBD2 port for connection to scanners and tuning tools
    • Made in the USA.
  • Billet Specialties 32121 Standard Horn Button - No Logo
    Billet Specialties 32121 Standard Horn Button - No Logo
    x
                  
    • Precision machined 6061-T6 billet aluminum
    • Fully polished
    • Stainless internal hardware
  • 1940 Ford Red Glass Tail Light Lens, Passenger Car
    1940 Ford Red Glass Tail Light Lens, Passenger Car
    x
                

    Replace those old, cracked, or missing tail lights with these reproduction red glass lens.  They are replacement tail light lens for your 1940 Ford passenger car.

    • Original reproduction
    • 1940 Ford passenger car only
    • Red glass lens
    • Sold each

     

     

  • 1932 Ford Tail Light Bracket, Chrome
    1932 Ford Tail Light Bracket, Chrome
    x
                

    These 1932 Ford tail light brackets are stamped steel reproductions. They feature a beautiful chrome plated finish. Choose left or right side.

    • 1932 Ford passenger cars
    • Chrome plated finish
    • Stamped steel reproductions
    • Specify left or right side
  • 1938-1939 Ford Blue Dot Tail-Stop Lights
    1938-1939 Ford Blue Dot Tail-Stop Lights
    x
                

    Polished stainless steel rim taillights for 1938-1939 Ford. These taillights have a blue dot glass lens, single 1157 dual filament bulb, and match the original tail lights closely.

    For 12 volt systems only. Mounting gasket sold separately.

     

Goto Previous PagePrevious Page
1 2 3 4 5 ... 20