Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Electrical, Lighting and Body At Speedway Motors

At Speedway Motors, we believe in a having a good-looking set of tail lights because with our performance parts, that's all the compeition usually sees! We have the largest selection of headlights, auxiliary lights and third brakes lights, plus the wiring harnesses to make it all work. We'll help you light up the night - you just focus on lighting up those tires!

Featured Products
Two Post Battery Disconnect Switch
Two Post Battery Disconnect Switch
(Part #91064500)
x
            Remote battery disconnect switch for safety and theft protection. A battery kill switch is required for use with alternators by the NHRA. Battery shut off switch can be remote mounted or where specified for saftey and  convenience.
  • 180 amp continuous, 1000 amp instantaneous
  • Die cast lever
  • Fits panel through 3/16" thick

910-64500 Instructions (PDF)

Heavy Duty Turn Signal Switch
Heavy Duty Turn Signal Switch
(Part #91062860)
x
            

For early autos not equipped with right and left turn signals. Chrome plated finish. Switch works with 6 or 12 volt systems. Includes wiring diagram. Clamps to any steering column with included stainless hose clamp. Switch has four-way flashers and does not self cancel.

You will need to purchase a three-prong flasher to use with this switch (part number 910-64046 or install kit 91062861). For LED light applications, you will also need a LED dummy load resistor (part number 910-03030).

910-62860 Instructions (PDF)

Black Dietz Type Headlights, Standard Bulb
Black Dietz Type Headlights, Standard Bulb
(Part #91101008)
x
            

Our universal fit Deitz-type 7" headlights feature black painted housings with chrome rings. Has a 12 volt sealed beam bulb with both high & low beams. "Drilled" mounting stud measures 1/2"-13. The pre-wired plug has 3 wires with 6" leads.

1928-1931 Ford Model A Stainless Tail Lights
1928-1931 Ford Model A Stainless Tail Lights
(Part #91127001)
x
            

Polished stainless steel housing with glass lenses. An excellent replacement or addition to your Model 'A' Ford. Left tail light has lenses on the bottom to illuminate a license plate. Choose left or right. 12 volt operation.

  • 3.851" diameter
  • 3" depth
  • 3.851" height
  • 1-3/4" mount 

Wire colors:

  • Housing - Ground
  • Tail - Black
  • Stop - Green

These tail lights have two bulbs in them that are of a single filament style. 

Lokar SP-1500U GM Speedometer Drive Cable Kit, Black
Lokar SP-1500U GM Speedometer Drive Cable Kit, Black
(Part #491SP1500U)
x
            

The finishing touch to your mechanical (cable-drive) speedometer installation in your GM or Mopar. Includes a 7 ft. long glossy black vinyl housing and inner cable (you trim to length) with billet aluminum ends, and instructions.

Works with all cable-drive aftermarket and original equipment speedometers that have a male 5/8"-18 thread connection. Has a 7/8"-18 end for the transmission.

GM Installation Instructions (PDF)

Universal Headlight Switch With Hi/Low
Universal Headlight Switch With Hi/Low
(Part #91080154)
x
            

This headlight switch has four positions. In is off, out one notch is park lights, out another notch is lows beams, and all the way out is high beams. Screw type terminals. 3/8" mounting hole.

910-80154 Instructions (PDF) 

LED Cat Eye Tail Light
$39.99
Product Rating: 4.73 Stars
LED Cat Eye Tail Light
(Part #91137035)
x
            

This 12-volt, 12-LED tail light can be used as a stop/turn/tail or just use as a third stop light. Measures 7.25" long x 1-50" tall x .730" thick with a chrome bezel. Light is flat on the back side and comes with a mounting gasket.

10-32 mounting bolts (not) included.

LED Cat Eye Tail Light Installation Instructions (PDF) 

Power Window Kit
$149.99
Product Rating: 4.80 Stars
Power Window Kit
(Part #91123333)
x
            
  • Kit for 2 doors
  • Works for all flat glass windows
  • Straight up and down travel only
  • 6"-24" Glass height
  • Includes: Switches, wiring and crossover kit

Instructions (PDF)

"Electrical, Lighting and Body" Page 1 of 21

  • AFCO 85053B Starter Switch Panel with Lights, 4-1/8 x 5-7/8 Inch
    AFCO 85053B Starter Switch Panel with Lights, 4-1/8 x 5-7/8 Inch
    (Part #10685053B)
    x
                

    AFCO starter switch panels are for standard ignitions.

    Wiring Instructions (PDF)

  • Lokar SG-6009 Chrome Dimmer Switch Cover, Chevy/Ford
    Lokar SG-6009 Chrome Dimmer Switch Cover, Chevy/Ford
    (Part #4916009)
    x
                Brighten up that old dimmer switch with one of these new dimmer switch covers from Lokar!  Made from steel and feature a beautiful chrome finish and a textured rubber pad. 
            
  • DEi 030305 Lite N Boltz LED Bolts, Amber
    DEi 030305 Lite N Boltz LED Bolts, Amber
    (Part #91068003)
    x
                

    Available in five different colors, these LED stainless steel button head bolts can be used for anything imaginable. These can be used on the interior or exterior and are compact enough to put anywhere. Sold per pair and have 5/16"-18 x 3/4" threads. 12 volt. Has a 9/16" O.D.

    Useful as:

    • Map and gauge lights
    • Indicator signals
    • Step illumination
    • Engine compartment lighting
    • Running boards
    • Truck bed rails
    • Dashboard accent lights

    Product FAQ's (PDF)

  • Modern Driveline Reverse Switch Harness - GM T5, T-56 Transmissions
    Modern Driveline Reverse Switch Harness - GM T5, T-56 Transmissions
    (Part #91070002)
    x
                

    These harnesses for transmission neutral safety switch/reverse light switches are designed for use with GM T5 and T56 transmissions.

    • Factory style
    • For GM T5 and T56 transmissions

     

  • 1954 Chevy Park Light Lens, Amber
    1954 Chevy Park Light Lens, Amber
    (Part #9115400)
    x
                These amber parking light lens for 1954 Chevy passenger cars feature  original   style lens pattering. They fit the factory housing    and are  a direct   replacement for your old damaged or missing park light    lens. 
    • Amber plastic lens with original style lens patterning 
    • Fits factory housing
    • Left or Right Side
    • Fits All Passenger Cars
    • Sold each
  • 1933-34 Ford Car, 1935-37 Ford Truck Headlight Mount Pads
    1933-34 Ford Car, 1935-37 Ford Truck Headlight Mount Pads
    (Part #7514013130)
    x
                

    These headlight mount gasket pads fit '33-'34 Ford passenger cars as well as '35-'37 Ford pickup trucks.  They are rubber construction and are not visible when properly installed.  Use these rubber gaskets to ensure a tight seal.

    • OEM replacements
    • 1933-'34 Ford passenger cars and 1935-'37 Ford pickups
    • Rubber construction
    • Sold as a pair
  • Halogen Tail Light Bulbs, 1157 Offset Mounting Pins
    Halogen Tail Light Bulbs, 1157 Offset Mounting Pins
    (Part #91131016)
    x
                

    Those other super bright, super high powered tail light bulbs may be easy to see, but they also generate enough heat to discolor your lens and burn the paint.

    Halogen tail light bulbs are brighter than standard bulbs, but use less energy, which means they burn cooler. 12 volt only.

    This bulb is shorter than a 1157 bulb and measures only 1-3/4" from bottom to end of the tip. From the pin to tip is 1-1/2".



     

  • Tall Model T Cowl-Tail Lights, Black
    Tall Model T Cowl-Tail Lights, Black
    (Part #91117400)
    x
                

    Features a 12 volt dual element bulb and can be used as a tail light or a cowl light. 9-1/2" tall with 3" diameter lens. Specify red or amber lens.

    Note: Mount bracket is NOT included. Lens must be secured in place with silicone (see Instructions).

    Cowl Light Installation Instructions (PDF)

  • 1932 Ford Stainless Tail Lights
    From: $29.99
    Product Rating: 4.67 Stars
    1932 Ford Stainless Tail Lights
    (Part #91137005)
    x
                

    These are an exact duplicate of the original 1932 Ford glass lens tail lights. Left light has a lens to illuminate license plate. Choose left or right.

    • 12 volt bulb
    • Highly polished stainless steel housing & rim
    • Cloth braided wire loom
    • Stainless steel screws
    • Glass red lens
    • 3-7/8" diameter, 2-3/8" depth
    • 2-11/16" overall depth (includes the wire retainer on the back of the lamp)

     

  • 1968 Belair/Biscayne LED Tail/Stop Lights
    1968 Belair/Biscayne LED Tail/Stop Lights
    (Part #91137075)
    x
                

    Face it, it's hard to see those tail lights on older cars. Now is the time to change out those broken or faded tail lights for new LED versions. 

    • 40 Super Bright LEDS
    • Polycarbonate Lens
    • Epoxy Coated, Fully Sealed Electronics, 1157 Plug
    • Solid State Circuit Boards Designed for 7.7 - 14.0 VDC

     

  • Stewart Warner 279B-F Deluxe Electrical Oil Pressure Sender
    Stewart Warner 279B-F Deluxe Electrical Oil Pressure Sender
    (Part #665279B)
    x
                

    Designed to make sure that you get fast, accurate information from your Stewart Warner gauges. 

    • 1/8-27 NPT
    • Electrical
    • Designed to be used with 90° sweep gauges
  • 1949-1950 Chevy Chrome Tail Light Bezel with Red Reflector
    1949-1950 Chevy Chrome Tail Light Bezel with Red Reflector
    (Part #91149502)
    x
                These tail light bezels for 1949-1950 Chevy passenger cars replicate those of the original. They feature a chrome plated finish and the original style red reflectors. 
    • Chrome plated steel bezel
    • Has original style red reflector with "GUIDE" script
    • Duplicate of original
    • Left or Right Side
    • Fits All Passenger Cars
  • American Autowire 37788 1955 Chevy OEM Style Turn Signal Switch
    American Autowire 37788 1955 Chevy OEM Style Turn Signal Switch
    (Part #91037788)
    x
                

    If you're still running the stock column in your 1955 Chevy car, you'll probably need one of these OEM style turn signal switches.  They come complete with the male connector body.

    • 1955 Chevrolet passenger car
    • OEM style replacement
    • Complete with male connector body

     

  • AFCO 85293 Warning Light, Oil Temp.
    AFCO 85293 Warning Light, Oil Temp.
    (Part #10685293)
    x
                

    These lights allow the driver to maintain focus on the race.

    Wiring Instructions (PDF)

  • Fuse Block for Glass Fuses
    $9.99
    Product Rating: 5.00 Stars
    Fuse Block for Glass Fuses
    (Part #91064004)
    x
                

    Allows easy installation of extra fuses or for use in basic electrical systems. Accepts 7 glass fuses. Also included is two connector strips, one ties three fuses to a common power source and one ties two fuses to a common power source.

  • MSD 8183 2-Pin Deutsch Connector, 16 gauge
    New
    MSD 8183 2-Pin Deutsch Connector, 16 gauge
    (Part #5478183)
    x
                There is absolutely no excuse for losing a race due to a poor wiring connection. MSDs Deutsch Connectors are sealed and lock together making them perfect for harsh racing applications. The compact housing of the connectors are molded from a durable plastic material that will not harden or crack. Each housing is indexed to prevent any chance of mismatching the ends plus they have a molded channel to secure another connector for a tidy appearance.The terminals grip to the wire with strong crimp tabs then lock into position inside the housing. The connections are protected with thick seals that will keep water, mud and debris away from the contacts. These terminals can handle more current than conventional connectors and do not require special tools. Supplied with terminals, seals and housings.

    Installation Instructions (PDF)

  • Painless Wiring 50302 6-Switch Fused Panel with Wiring and Hardware
    New
    Painless Wiring 50302 6-Switch Fused Panel with Wiring and Hardware
    (Part #91050302)
    x
                

    This heavy duty lightweight switch panel from Painless Performance is designed to mount to a roll bar using standard metal hose clamps. Lighted rocker switches are color coded for quick reference.  All of the circuits are individually fused and are easily accessible for quick testing and replacement. This kit comes complete with 18 ft. of TXL wire, using fully insulated terminals. Made in the USA!

    Installation Instructions (PDF) 

    The Kit Controls:

    • Start
    • Ignition
    • Fuel pump
    • Electric fan/water pump (Switch up position - fan on only / Switch middle position - all off / Switch down position - fan & water pump on)
    • Two accessories

     

     

  • Lokar CC-1600U Carbureted Cruise Control Cable, Black
    Lokar CC-1600U Carbureted Cruise Control Cable, Black
    (Part #491CC1600U)
    x
                
    • Lokar cruise control cable is for use with Rostra control kits. Kit includes 4 foot stainless outer housing designed with a specialty extruded liner for extended life of the cable and 5 feet of stainless inner wire, which replaces black plastic cable in Rostra kits. Cables are u-cut-to-fit inside and outside of the firewall. All billet aluminum fittings, stainless hold down clip and mounting bracket. Mount cable to carburetor with Lokar's stainless carburetor bracket and return springs.
    • For Use w/Rostra Control Kits
    • Stainless Housing
    • 5 in. Stainless Inner Wire/4 in. Outer Housing
    • U-Cut-To-Fit Inside And Outside Of Firewall
    • Billet Aluminum Fittings
    • Incl. Hold Down Clip/Mounting Bracket
    • Made In The U.S.A.
    • Lifetime Warranty
  • Speedway 7 Inch Fluted Replacement Headlights w/ Amber Turn Signal
    Speedway 7 Inch Fluted Replacement Headlights w/ Amber Turn Signal
    (Part #9106121)
    x
                

    Speedway's 7" replacement Fluted H4 Headlights allow you to have "the look" with out breaking the bank. Features a chrome plated plastic reflector with a glass lens and an "amber" turn signal lens. Includes a H4 Halogen bulb.

    These headlights have a separate 94-style single filament bulb which can be used as a turn signal or a running lamp (not both). 

    • 6-5/8" headlight O.D.
    • Wiring pigtail for turn/running light is included
    • Wiring pigtail for headlight NOT included
    • Uses common 3-prong headlight plug-in

    Headlight Wiring Chart (GIF)

    Installation Instructions (PDF)  

  • Stewart Warner 82623B GM Sender for Wings Electronic Speedometer
    Stewart Warner 82623B GM Sender for Wings Electronic Speedometer
    (Part #66582623B)
    x
                

    This sending unit for electronic speedometers has a .894" (7/8”) female attachment nut to attach it to the transmission or out-drive unit.  This is similar to the female threaded ring on mechanical speedometer cables. Most customers will need to purchase part number 66582629, square drive tip, to attach this sender to a GM transmission.

  • 1928-29 Dropped Stainless Headlight Bars
    1928-29 Dropped Stainless Headlight Bars
    (Part #91121803)
    x
                1928-1929 Dropped style stainless steel headlight bars. Polished. 

    Top width (flange tip to flange tip) 42-1/2"
    Bottom width (flange tip to flange tip) 38-1/2"
  • 1957 Chevy LED Tail Light Conversion Kit
    1957 Chevy LED Tail Light Conversion Kit
    (Part #91131040)
    x
                The 1957 Chevy cars were not known to have very bright or visible tail lights. The cure is the addition of LED conversion kits. 

    These replace old 1157 style bulbs with 14 LED bulbs that are much brighter, don't put out much heat and last up to 100,000 hours. Stainless steel hardware and easy 30 minute installation.

    1957 Chevy LED Tail Light Conversion Instructions (pdf)

  • MSD 8961 MSD High Current Relay, SPST
    $26.99
    $29.99
    New
    MSD 8961 MSD High Current Relay, SPST
    (Part #5478961)
    x
                MSDs High Current Relays are what you need to activate accessories that draw high current. These Relays are very reliable due to the fully automated manufacturing process and sophisticated coil winding procedure. The SPST High Current Relay is rated at 30 amps with an input voltage of 12 volts DC. The relay is ideal for use with the MSD RPM Activated Switch when 12 volts are responsible for activating a high current device such as a nitrous solenoid.The DPST relay is also rated at 30 amps with a 12 volt input voltage. This Relay is the best choice when 12 volts are required to activate multiple high current devices at the same time such as multiple stage nitrous solenoids.

    Installation Instructions (PDF)

  • MSD 8190 10 Male Pins and Seals
    $8.99
    $9.99
    New
    MSD 8190 10 Male Pins and Seals
    (Part #5478190)
    x
                Male pins and seals for use with Weathertight Connectors.
            
  • MSD 7990 Dual Ignition Kill Switch
    MSD 7990 Dual Ignition Kill Switch
    (Part #5477990)
    x
                

    When running a crank trigger, you now have an option of two base timings. When the track gets slick, just flip the switch to kill some power.

     MSD Rebate (Link)

  • 1928-29 Model A Style Headlights
    1928-29 Model A Style Headlights
    (Part #91121011)
    x
                Available in polished stainless steel. 12 volt bulb is mounted behind original style lens. Complete with mounting stud. 9" diameter. Stainless with Halogen bulb. 
            
  • MSD 8187 4-Pin Deutsch Connector, 12-14 gauge
    New
    MSD 8187 4-Pin Deutsch Connector, 12-14 gauge
    (Part #5478187)
    x
                There is absolutely no excuse for losing a race due to a poor wiring connection. MSDs Deutsch Connectors are sealed and lock together making them perfect for harsh racing applications. The compact housing of the connectors are molded from a durable plastic material that will not harden or crack. Each housing is indexed to prevent any chance of mismatching the ends plus they have a molded channel to secure another connector for a tidy appearance.The terminals grip to the wire with strong crimp tabs then lock into position inside the housing. The connections are protected with thick seals that will keep water, mud and debris away from the contacts. These terminals can handle more current than conventional connectors and do not require special tools. Supplied with terminals, seals and housings.

    Installation Instructions (PDF)

    • Sealed Connectors
  • EMPI 16-2059 Bullet Light Assembly, Convex Red, Each
    EMPI 16-2059 Bullet Light Assembly, Convex Red, Each
    (Part #1412059)
    x
                

    EMPI Bullet lights feature a high power 12-Volt 50 watt halogen bulb with a mirror finish reflector. The compact (approximately 3-1/2" tall by 2-1/2" diameter) housing is made of precision machined aluminum.

    • Bullet Light w/ Red Lens
    • Precision machined aluminum housing
    • Mounts on flat or slightly rounded surfaces
    • Sold Each

  • MSD 8184 2-Pin Deutsch Connector, 12-14 gauge
    New
    MSD 8184 2-Pin Deutsch Connector, 12-14 gauge
    (Part #5478184)
    x
                There is absolutely no excuse for losing a race due to a poor wiring connection. MSDs Deutsch Connectors are sealed and lock together making them perfect for harsh racing applications. The compact housing of the connectors are molded from a durable plastic material that will not harden or crack. Each housing is indexed to prevent any chance of mismatching the ends plus they have a molded channel to secure another connector for a tidy appearance.The terminals grip to the wire with strong crimp tabs then lock into position inside the housing. The connections are protected with thick seals that will keep water, mud and debris away from the contacts. These terminals can handle more current than conventional connectors and do not require special tools. Supplied with terminals, seals and housings.

    Installation Instructions (PDF)

    • Waterproof
    • Quick Connect
  • MSD 8910 Tach Adapter
    $42.99
    $50.99
    New
    MSD 8910 Tach Adapter
    (Part #5478910)
    x
                If, after installing an MSD Ignition Control, your ta­chometer, fuel pump relay or electronic fuel injection (in foreign vehicles) doesnt operate correctly, your ap­plication may require a Tach Adapter. This is due to the trigger signal not being strong enough to trigger both the MSD and the factorys components.There are a few Tach Adapters available and for more information see pages 152 and 153. Each Adapter is simple to wire in and will have your MSD and vehicle firing away in no time! If you are triggering an MSD Blaster, 5, 6, SCI, or 7 Series Ignition with its white wire or points terminal, you will need the PN 8910 Tach Adapter. The PN 8910 will correct the operation of most voltage-triggered tachometers or fuel injection systems that do not work directly off the tach output terminal of the MSD Ignition Unit.

    Installation Instructions (PDF)

    Installation Instructions (PDF)

    • Lokar SP-1503HT Ford Speedometer Drive Cable Kit, Stainless
      Lokar SP-1503HT Ford Speedometer Drive Cable Kit, Stainless
      (Part #491SP1503HT)
      x
                  

      The finishing touch to your mechanical (cable-drive) speedometer installation in your Ford. Kit includes a 7 ft. long braided stainless steel housing and 7' inner cable (you trim to length), billet aluminum fitting ends and instructions.

      Works with all cable-drive aftermarket and original equipment speedometers that have a male 5/8"-18 threaded connection. The transmission end has the standard Ford end with retaining clamp.

       Ford Installation Instructions (PDF) 

    • Lokar SP-1506U Early Ford Speedo Cable Kit w/Ford End, Black Housing
      Lokar SP-1506U Early Ford Speedo Cable Kit w/Ford End, Black Housing
      (Part #491SP1506U)
      x
                  Premium housing designed with a specially extruded liner for extended life of the cable and billet aluminum fittings. Inner cable and outer housing are "U-Cut-to-Fit". Kit comes complete with all fittings and is available for GM, Ford and Chrysler applications. (Gauges not included)
      Lokar Speedometer Cables are designed to work with most cable driven aftermarket speedometer gauges (such as Auto Meter, Stewart Warner, VDO, Classic Instruments, etc.) or factory speedometer.
      Lokar Speedometer Cables are designed to fit into the transmission gear adapter (not supplied in Chevy or Chrysler Lokar Kit). Customer must have the trans end adapter and speedometer gear for all Chevy and Chrysler applications. For Ford applications, the gear adapter is supplied in the Lokar Kit. Customer must supply the speedo gear and speedo gear retainer clip.
      • All Lokar Speedometer Cables are seven feet (7') long
      • Designed to be "U-Cut-to-Fit".
      • Additional length cable in black or stainless housing is available upon request for an additional charge.
      • Must have a 3/4 - 20 female thread at the speedometer
    • 1955 Chevy LED Tail Light Conversion Kit
      1955 Chevy LED Tail Light Conversion Kit
      (Part #91131030)
      x
                  The 1955 Chevy cars were not known to have very bright or visible tail lights. The cure is the addition of LED tail light conversion kits. 

      These replace old 1157 style bulbs with 14 LED bulbs that are much brighter, don't put out much heat and last up to 100,000 hours. Stainless steel hardware and easy 30 minute installation.

      1955 Chevy LED Tail Light Conversion Instructions (pdf)

    • DEi 030304 Lite N Boltz LED Bolts, Red
      DEi 030304 Lite N Boltz LED Bolts, Red
      (Part #91068001)
      x
                  

      Available in five different colors, these LED stainless steel button head bolts can be used for anything imaginable. These can be used on the interior or exterior and are compact enough to put anywhere. Sold per pair and have 5/16"-18 x 3/4" threads. 12 volt. Has a 9/16" O.D.

      Useful as:

      • Map and gauge lights
      • Indicator signals
      • Step illumination
      • Engine compartment lighting
      • Running boards
      • Truck bed rails
      • Dashboard accent lights

      Product FAQ's (PDF)

    • Longacre 44611 Flip-Up Start/Ignition Switch Panel w/Pilot Light
      Longacre 44611 Flip-Up Start/Ignition Switch Panel w/Pilot Light
      (Part #47544611)
      x
                  These high capacity (40 amp at 12 volts) ignition switch panels with aircraft style cover and pilot light are easy to turn off in an emergency from any angle, even with gloves. Will not turn off from vibration. They come pre-wired with high insulation "Fat" wires and soldered terminals with heat shrinked seals.
      • Starter button with weatherproof cover
      • Lightweight aluminum panel
      • Plugs into Longacre wiring harness P/N 44930
      • Ignition Switch:
        • Style:    Toggle
        • Cover:    Aircraft style flip
        • Pilot Light Included:   Yes
        • Rating:    40 amps @ 12 volts
      • Starter Switch:
        • Style:    Push button
        • Cover:    Weatherproof rubber
        • Rating:    15 amps @ 12 volts resistive
      • Panel:
        • Material:    Lightweight aluminum
        • Panel Dimensions:   3-1/2" x 3-1/2"
        • Wiring Included:    Yes
    • Lokar XBAG-6109 Midnight Series Oval Billet Aluminum Dimmer Cover
      Lokar XBAG-6109 Midnight Series Oval Billet Aluminum Dimmer Cover
      (Part #491XBAG6109)
      x
                  
      • Oval Billet Aluminum Dimmer Cover – Brushed
      • Black Anodized Billet Aluminum 
      • Made In The U.S.A.

       

    • Toggle Ignition On Switch
      $9.99
      Product Rating: 4.75 Stars
      Toggle Ignition On Switch
      (Part #91364380)
      x
                  Toggle switch works great as a kill switch or with other auxiliary equipment. 25 amp SPST switch with rubber boot and on/off plate.
              
    • 1930-31 Ford Model A Dropped Headlight Bar Kit, Stainless
      1930-31 Ford Model A Dropped Headlight Bar Kit, Stainless
      (Part #91121810)
      x
                  Get everything you need to complete your  dropped headlight bar installation with this convenient kit!  All for  one money saving price.

      Includes:
      • 911-21809 - Stainless Headlight Bar
      • 751-A13130BS - Rubber mounting pads
      • 751-A13130SS - Hardware kit
    • Universal Headlight Mount
      $19.99
      Product Rating: 4.00 Stars
      Universal Headlight Mount
      (Part #91061026)
      x
                  
      • 5/16" mounting holes 2" center to center
      • 1/2" ID sleeve for light mounting bolt
      • Great for headlights and taillights
      • Use with mounting cups 91061034
    • 1932 Ford Tail Light LED Conversion Lens
      1932 Ford Tail Light LED Conversion Lens
      (Part #91137026)
      x
                  These direct replacement tail light lenses will convert your 1932 Ford Deuce tail lights to powerful and bright LED lights. Choose left or right sides.
      • 17 Super Bright Red LEDs
      • Drivers side (Left side) includes a 4 LED White License Light (primary picture)
      • Epoxy coated, fully sealed electronics
      • Two 1156 plugs
      • Solid state circuit board for 12V systems 
      1932 Ford LED Tail Light Conversion Instructions (pdf)
    Goto Previous PagePrevious Page
    1 2 3 4 5 ... 21