Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 9

Products

Shop Edelbrock Products At Speedway Motors

Proven Performance is the philosophy that began when Vic Edelbrock Sr. founded Edelbrock Performance Parts in 1938. This philosophy continues today with the same high standard of performance and quality that goes into every Perfomer Series intake manifold, Edelbrock 94 carburetor, and Flathead cylinder head. Vic Edelbrock Sr. would be proud of what has grown out of his small racing parts garage in Los Angeles, CA., just like Speedway Motors is proud to carry his products.

Featured Products
  • Edelbrock 2176 Performer Series Intake Manifold, Chrysler 318/360 V8
    New
    Edelbrock 2176 Performer Series Intake Manifold, Chrysler 318/360 V8
    (Part #3252176)
    x
                

    Designed for use with Chrysler Small Block V8 engines such as the 318/340/360, the Performer Series intake manifold from Edelbrock is a stock replacement/street legal addition to your OEM 4 barrel carburetor.  These manifolds are not equipped with EGR valves for original appearance and function.

    • For Chrysler 318/340/360 V8 engines
    • OEM replacement
    • Satin finish

    Note: These are now IMCA approved for Hobby Stocks, Stock Cars, and SportMods.

    Note: These manifolds are not for use on marine engines used in salt water. Will not fit 1992 and later Magnum engines.

    3252176 Installation Instructions (PDF)

  • Edelbrock 8089 Carburetor Fuel Line Banjo Fitting, 3/8 Inch
    Edelbrock 8089 Carburetor Fuel Line Banjo Fitting, 3/8 Inch
    (Part #3258089)
    x
                

    This banjo fitting from Edelbrock features an inlet fitting that is a must-have accessory when installing or tuning your Edelbrock carburetor. These fittings are for Edelbrock Square-Bore and Carter AFB carburetors. Each is manufactured from quality material and sold individually.

    • Fitting End A: 5/8"-20
    • Fitting End B: 3/8"
    • Wrench Type: Hex 
    • For 5/16" fuel line


  • Edelbrock 1146 1949-53 Flathead Offset Generator Bracket
    Edelbrock 1146 1949-53 Flathead Offset Generator Bracket
    (Part #3251146)
    x
                

    This bracket offsets the generator to the passenger side (RH) on '49-'53 Ford Flathead V8s. A special water neck is included that helps to re-route the hose around the relocated generator. This bracket only fits a stock Ford generator, NOT a Powegen.

    Fits most intakes.

    325-1146 Instructions (PDF)

  • Edelbrock 1115 1949-53 Ford Flathead Finned Cylinder Heads, 65cc
    Edelbrock 1115 1949-53 Ford Flathead Finned Cylinder Heads, 65cc
    (Part #3251115)
    x
                

    Extensive R&D and modern CAD systems give these heads more power potential and greater heat control than any before! Works well on stock or modified engines. For 1949-1953 Ford 8BA and 8CM Mercury V8 engines (24-stud).

    • The original Edelbrock design
    • Rugged, ribbed internally and externally with a large water capacity
    • Cast at the Edelbrock Foundry in the USA of T-6 tempered A356 aluminum
    • Excellent breathing characteristics
    • 8:1 compression with stock bore & stroke
    • C/R increase is approx 3/10 of a percent with each 1/8" stroke
    • Accepts .410" valve lift

    325-1115 Instructions (PDF)

  • Edelbrock 1406 Performer 600 CFM 4 Barrel Carburetor, Electric Choke
    Edelbrock 1406 Performer 600 CFM 4 Barrel Carburetor, Electric Choke
    (Part #3251406)
    x
                

    Edelbrock Performer Series 4 barrel carbs have proven themselves to be easy to tune with great drivability. Whether you need to replace an aging stock carb or are looking for a performance carb to top off your hot rod, this Edelbrock carb is the best choice for performance and value. All Edelbrock products are proudly made in the U.S.A.

    CALIBRATED FOR FUEL ECONOMY
    Designed for small-block and small displacement big-block engines, this four barrel carb is recommended only for stock to Performer level applications. They are not recommended for use on RPM or Torker II intake manifolds. Match with an Edelbrock Performer or Performer EPS manifold and other brands of similar design. Calibrated 2% leaner than #1405. Includes both timed and full vacuum ports for ignition advance. Comes with: Metering Jets Primary .098, Secondary .095; Metering Rods .075 x .047; Step-Up Spring yellow (4" Hg). Includes an electric choke and detailed instructions. Ford/Mopar throttle adapter arms sold separately. 

    • Easy to tune with great driveability
    • 600 CFM
    • Electric choke
    • Ford/Mopar arms sold separately

    Edelbrock 600 CFM 4 Barrel Carburetor Installation Instructions (PDF)

  • Edelbrock 4025 Uni-Syn Carburetor Synchronizing Tool
    Edelbrock 4025 Uni-Syn Carburetor Synchronizing Tool
    (Part #3254025)
    x
                

    If you have more than one carb on your hot rod, you need one of these "Uni-Syn" carb synchronizing tools. Just set on the top of your carb and adjust until all the carbs in your tri-power three deuce set-up read the same. 

    Works well on small one barrel and two barrel carbs (downdraft or side-draft). Fits carb necks from 1-3/8" up to 3".

  • Russel Performance 662041 Endura Finish Aluminum Pipe Plug 1/4 In. NPT
    Russel Performance 662041 Endura Finish Aluminum Pipe Plug 1/4 In. NPT
    (Part #61766204)
    x
                

    Don't you just hate it when you have a polished intake or water pump and the only pipe plugs you can find are blue or steel? These Allen head aluminum plugs from Russell Performance have a durable anodized Endura finish.

    Fitting Thread Application Chart (GIF)

  • Edelbrock 2186 Performer 383 Series Manifold for B/B Chrysler
    New
    Edelbrock 2186 Performer 383 Series Manifold for B/B Chrysler
    (Part #3252186)
    x
                

    This Edelbrock Performer Series Manifold is designed for street 361-383-400 Chrysler V8s that measure 7.75" across block. This is a stock replacement/street legal part for 400 V8's with OEM 4-bbl carburetors.

    • Chrysler 361-400 V8
    • Idle 5500 RPM
    • For B/B Chrysler
    • Sold Individually

     

     

     

Filter

"Edelbrock" Page 1 of 9

Page 1 of 9

  • Edelbrock 1413 Performer 4 Barrel Carburetor, 800 CFM, Electric Choke
    Edelbrock 1413 Performer 4 Barrel Carburetor, 800 CFM, Electric Choke
    (Part #3251413)
    x
                

    Edelbrock Performer Series four barrel carbs have proven themselves to be easy to tune with great drivability. Whether you need to replace an aging stock carb or are looking for a performance carb to top off your hot rod, the Edelbrock Performer Series carbs are the best choice for performance and value. All Edelbrock products are proudly made in the U.S.A.

    Designed and calibrated for maximum street performance with most Performer RPM, RPM Air-Gap and Torker II manifolds and with Performer manifolds on large cubic-inch engines. Includes an electric choke and detailed instructions. Ford/Mopar throttle adapter arms sold separately.

    • Electric choke 
    • Smooth throttle response throughout the power band
    • Uses metering rods to transition between circuits - rods can be changed in seconds without carburetor removal or draining fuel
    • Float levels are factory set; adjustments are rarely needed
    • Change jets, adjust floats & replace needles/seats without draining fuel or removing carb
    • Lightweight all-aluminum body is compatible with gasohol and blended fuels
    • Includes both timed and full vacuum ports for ignition advance

    Edelbrock 800 CFM 4 Barrel Carburetor Installation Instructions (PDF)

     

  • Edelbrock 5001 Small Block Chevy Torker II Intake Manifold
    Edelbrock 5001 Small Block Chevy Torker II Intake Manifold
    (Part #3255001)
    x
                

    Designed for 1955-86 high-performance 262-400 c.i.d. small-block Chevy V8s operating in the 2500-6500 RPM range. The Torker II is an updated version of original Torker offering better performance. Manifold accepts late-model waterneck, air-conditioning, alternator and H.E.I. distributor.

    Will fit Corvette and 1987 and later stock aluminum heads. Will NOT fit 1987 and later cast iron heads and will NOT cover port openings of Chevrolet Bowtie or LT1 heads.

    NOT intended for use on heavy vehicles (trucks, vans etc.).

    Torker II Intake Manifold Installation Instructions (PDF)

  • Edelbrock Big Block Chevy Dual Quad Set-Up, Rectangular Port
    Edelbrock Big Block Chevy Dual Quad Set-Up, Rectangular Port
    (Part #92519917)
    x
                

    There is nothing sweeter looking or sounding than a dual quad on a Chevy! This one kit gets you two manual choke Edelbrock carbs, an Edelbrock unpolished intake manifold, fuel line and special progressive linkage. Just add a suggested air cleaner to finish your installation.

    • 1500-6000 RPM
    • Will clear HEI distributors
    • Will not fit tall-deck truck blocks
    • Has 6-7/16" carb centers

    Overall Height from the bottom of the intake to the top of the air cleaners below:

    325-4237: 11.795"

    325-1235: 11.272"

    325-4119: 12.965"

    Height from bottom of intake to carb mounting surface: 4.899"

    • Port exit dimensions:  1.66" x 2.30

     

  • Edelbrock 14064 Endurashine Performer 600 CFM 4 BBL Carb, Electric
    Edelbrock 14064 Endurashine Performer 600 CFM 4 BBL Carb, Electric
    (Part #32514064)
    x
                Please view the product's page for more information
            
  • Edelbrock 41409 Classic 348/409 Satin Valve Covers
    Edelbrock 41409 Classic 348/409 Satin Valve Covers
    (Part #32541409)
    x
                

    Edelbrock first made these aluminum valve covers in the late '50s and they're still a classic. Made of heavy-gauge sand-cast aluminum, our classic finned valve covers are available in either a classic polished aluminum or durable black powder coated finish. Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.

    • Chevy 348/409
    • Heavy gauge material
    • 3-13/16" overall height
    • Made in the U.S.A.
  • Edelbrock 2215 LS1 Performer RPM Hydraulic Roller Cam, 1500-6500 RPM
    Edelbrock 2215 LS1 Performer RPM Hydraulic Roller Cam, 1500-6500 RPM
    (Part #3252215)
    x
                

    Edelbrock LS1 camshaft for 1997 and up Corvettes and 1998-2002 Camaro/Firebird LS1/LS6 based engines. This cam features more aggressive profiles than conventional cams without excessive valve overlap. Intended for use with OEM or Edelbrock hydraulic roller tappets. Dyno testing has resulted in 25HP gain over stock!

    Note: This camshaft is designed to be used in engine swap applications using a CARBURETOR ONLY. It is not intended to be used in factory EFI-equipped LS1 vehicles.

    325-2215 Instructions (PDF)

  • Edelbrock 2921 Victor Jr. Ford 302 Intake Manifold
    Edelbrock 2921 Victor Jr. Ford 302 Intake Manifold
    (Part #3252921)
    x
                

    The Edelbrock Victor Series intake manifolds have set the standard for quality and performance in the racing industry. The Victor Jr. 302 is designed for Ford 260-289-302 competition engines using modified stock cast iron or aftermarket Windsor-style cylinder heads.

    The Victor Jr. 302 has no rear water crossover. Port exit size at cylinder head is 1.90" x 1.08" with enough extra material to open it up to 2.10" x 1.18".

    325-2921 Instructions (PDF)

  • Edelbrock 12801 Polished 2-Carb Fuel Block
    Edelbrock 12801 Polished 2-Carb Fuel Block
    (Part #32512801)
    x
                

    Edelbrock has reintroduced the vintage cast aluminum fuel blocks for dual, triple and quad carb applications for your hot rod or custom. This fuel log features a single 3/8" NPT inlet and two 1/4" NPT outlets. Each fuel distribution block has four holes for mounting to a firewall.

    Polished finish.

  • Edelbrock 5408 348/409 Dual Quad Intake Manifold, Small Port
    Edelbrock 5408 348/409 Dual Quad Intake Manifold, Small Port
    (Part #3255408)
    x
                

    Performer RPM Dual-Quad intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W" Series engines. These manifolds deliver performance improvements in the 1500-6500 rpm range with Edelbrock Performer Series dual-quad carburetors, and they accept Edelbrock dual-quad accessories including fuel lines, throttle linkage, and air cleaners.

    Includes oil fill tube (not installed) and matching push-in breather cap. Use with dual quad linkage and fuel line at right. Carb center-to-center measurement is 6-7/16".

    325-5408 Instructions (PDF)

  • Edelbrock 75014 RPM Air-Gap S/B Chevy Intake Manifold, Endurashine
    Edelbrock 75014 RPM Air-Gap S/B Chevy Intake Manifold, Endurashine
    (Part #32575014)
    x
                

    Designed for 1955-86 262-400 c.i.d. Chevrolet V8s, the award-winning RPM Air-Gap incorporates the same race-winning technology that's used on the Victor Series competition intakes. The air-gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power.

    Manifold features rear water outlets, two distributor clamp locations and nitrous bosses. Accepts all 1976 and later alternator and A/C brackets for the street. The heater outlet boss is angled for proper fit over the valve cover. The temp sensor boss clears all waternecks.

    • For square-bore carburetors only
    • No provision for exhaust-heated chokes and no exhaust crossover
    • Not for 1987 and later cast iron heads
    • Will not fit under stock Corvette hood

    325-75014 Instructions (PDF)

  • Edelbrock 5412 289-302 Ford Three Deuce Tri Power Intake Manifold
    Edelbrock 5412 289-302 Ford Three Deuce Tri Power Intake Manifold
    (Part #3255412)
    x
                
    This intake for 3 deuces on a small block Ford does NOT have clearance for the Powerfire, Flamethrower, OEM, or any HEI style distributor. It requires the smaller cap as available on distributor 547-8352
    • 289-302 Small Block Ford 3 deuce aluminum intake
    • Designed to use 3 bolt carburetors such as the Speedway 9 Super 7's
    • For Stock/OEM standard deck
    • RPM range, Idle-5,500
    • Low Rise, Dual-plane design
    • Improved throttle response
    • Made of aluminum
    • Natural finish
  • Edelbrock 14073 Performer 4 Barrel Carb, 750 CFM, Manual Choke, Black
    Edelbrock 14073 Performer 4 Barrel Carb, 750 CFM, Manual Choke, Black
    (Part #32514073)
    x
                Please view the product's page for more information
            
  • Edelbrock 18064 Endurashine AVS 4 Barrel Carb, 650 CFM, Electric Choke
    Edelbrock 18064 Endurashine AVS 4 Barrel Carb, 650 CFM, Electric Choke
    (Part #32518064)
    x
                

    The Thunder Series' unique Qwik-Tune Secondary Air Valve allows for limitless calibration of the secondary circuit with simple hand tools while on your vehicle. It can be easily adjusted, in seconds, to suit your application - no extra parts required to achieve optimum performance. Also features Edelbrocks's amazing Endurashine finish that has the brilliance of chrome or a well-polished piece, but without the maintenance or the high price tag. This coating won't fade or oxidize and cleans up easily with soap and water.

    Designed and calibrated for optimum street performance in small-block and some big-block engines. Match with a variety of manifolds that include Edelbrock Performer, Performer EPS, Performer RPM, RPM Air-Gap, Torker II and other brands of similar design.

    • Primary and secondary booster clusters offer the most accurate and up-to-date calibration available for today's fuels and octane levels
    • Two-piece design means no gaskets below the fuel level for leak-free operation

    Edelbrock 650 CFM 4 Barrel Carburetor Installation Instructions (PDF)

  • Edelbrock 1146 1949-53 Flathead Offset Generator Bracket
    Edelbrock 1146 1949-53 Flathead Offset Generator Bracket
    (Part #3251146)
    x
                

    This bracket offsets the generator to the passenger side (RH) on '49-'53 Ford Flathead V8s. A special water neck is included that helps to re-route the hose around the relocated generator. This bracket only fits a stock Ford generator, NOT a Powegen.

    Fits most intakes.

    325-1146 Instructions (PDF)

  • Edelbrock 1487 Performer Carburetor Calibration Kit, 1406
    Edelbrock 1487 Performer Carburetor Calibration Kit, 1406
    (Part #3251487)
    x
                

    Most of the time you can bolt an Edelbrock Performer carb on your engine and it’s good to go. But if you have done a little tweaking on the engine you may need to tune it a bit. These kits include an assortment of metering rods and jets, one pair of metering rod retaining springs and a complete assortment of step-up springs.

    You may want to order a 325-1477 rebuild kit also.

  • Edelbrock 1479 Performer Carburetor Calibration Kit, 1405
    Edelbrock 1479 Performer Carburetor Calibration Kit, 1405
    (Part #3251479)
    x
                

    Most of the time you can bolt an Edelbrock Performer carb on your engine and it’s good to go. But if you have done a little tweaking on the engine you may need to tune it a bit. These kits include an assortment of metering rods and jets, one pair of metering rod retaining springs and a complete assortment of step-up springs.

    You may want to order a 325-1477 rebuild kit also.

  • Edelbrock 7159 Performer RPM Chevy 348/409 Intake Manifold, Large Port
    Edelbrock 7159 Performer RPM Chevy 348/409 Intake Manifold, Large Port
    (Part #3257159)
    x
                

    The Performer RPM W-Series intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W-Series" big-block engines. Two versions are available; one for small-port cast iron heads and the other for factory large port heads. They both deliver improved performance in the mid to high rpm range (1500-6500 rpm) when combined with an Edelbrock Performer carburetor. Also features a front mounted oil fill tube for those who want the nostalgic look of Edelbrock's Classic series valve covers with no breathers.

    2.39" x 1.15" Port Exit 

    Includes chrome oil fill tube (not installed) and matching push-in breather cap. For square-bore carburetors only.

  • Edelbrock 1411 Performer 750 CFM 4 Barrel Carburetor, Electric Choke
    Edelbrock 1411 Performer 750 CFM 4 Barrel Carburetor, Electric Choke
    (Part #3251411)
    x
                

    Edelbrock Performer Series four barrel carbs have proven themselves to be easy to tune with great drivability. Whether you need to replace an aging stock 4 barrel carb or are looking for a performance 4 barrel carb to top off your hot rod, the Edelbrock Performer Series carbs are the best choice for performance and value. All Edelbrock products are proudly made in the U.S.A.

    Designed for 402 c.i.d. and larger engines with Edelbrock Performer manifolds and other brands of similar design, these four barrel carbs are recommended only for stock to Performer level applications. They are not recommended for use on RPM or Torker II intake manifolds. Calibrated 2% leaner than #1407. Includes an electric choke and detailed instructions. Ford/Mopar throttle adapter arms sold separately.

    • Electric choke 
    • Smooth throttle response throughout the power band
    • Uses metering rods to transition between circuits - rods can be changed in seconds without carburetor removal or draining fuel
    • Lightweight all-aluminum body is compatible with gasohol and blended fuels
    • Includes both timed and full vacuum ports for ignition advance

    Edelbrock 750 CFM 4 Barrel Carburetor Installation Instructions (PDF)

     

     

  • Edelbrock 41439 Classic Series Valve Cover with Breather Hole, Satin
    Edelbrock 41439 Classic Series Valve Cover with Breather Hole, Satin
    (Part #32541439)
    x
                

    This classic series valve cover is manufactured from sand-cast, high quality, heavy gauge aluminum. Edelbrocks valve covers feature finishes to complete the look of your engine compartment. Made in the U.S.A.

    • 1959-86 Chevy 262-400 Small Block
    • 3-1/2" Overall Height
    • With Fill Hole
    • Satin finish

     

  • Edelbrock 6 Carb Throttle Linkage Kit for GM Ram Log Intake, 94 Carbs
    Edelbrock 6 Carb Throttle Linkage Kit for GM Ram Log Intake, 94 Carbs
    (Part #3251031)
    x
                

    This linkage is for an Edelbrock Ram Log intake with 6 "94" carbs on a 325-2150 intake. They feature progressive throttle blade action and include all necessary hardware and instructions for installation.

    • Designed for use on Edelbrock X1 Ram Log intake manifolds
    • Applicable to Edelbrock/Holley "94" carburetors only
    • 6-carb linkage kits
    • Originally designed by Vic Edelbrock Sr. for smooth carburetor operation

Goto Previous PagePrevious Page
1 2 3 4 5 ... 9