Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 50

Products

Driveline and Axles

Shop Driveline and Axles At Speedway Motors

Hook up that horsepower with driveline parts from Speedway Motors. Whether you're racing at your local dirt track, at the drag strip or just have a monster under the hood of your hot rod, we have the parts and technical know-how to help you put the power to the ground.

Featured Products
  • Micro Sprint Splined Rear Axle Bearing
    Micro Sprint Splined Rear Axle Bearing
    (Part #9601277)
    x
                

    These Micro Sprint splined rear axle bearings are in stock and ready to order. No need to run a rear axle bearing sleeve with these bearings, it is already built into them.

    • Steel Material
    • Sold Individually
    • 31 Spline Count

     

     

  • 9 Inch Ford Rear End Overhaul Kit
    9 Inch Ford Rear End Overhaul Kit
    (Part #9190950)
    x
                This 9" Ford overhaul kit includes: pinion pilot, pinion shaft, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear marking grease, brush and Loctite. Ring gear bolts not included. 

    NOTE: All Ford 9" full spools use overhaul kit 9190950-31, even if they are a 28-spline spool. The 9190950-31 contains the large I.D. standard O.D. carrier bearings and pinion bearings needed for use with our full spools.

    If you are using the H.D. nodular iron center section which uses the large diameter carrier bearings, order kit 9190950-31s, which also includes the large pinion bearings for use with the Daytona pinion support.

    9" Ford Carrier Bearing Chart (GIF)  - Double check your bearing p/n.

  • Spring Behind Axle Bracket
    $12.99
    Product Rating: 5.00 Stars
    Spring Behind Axle Bracket
    (Part #91635010)
    x
                

    Weld-on brackets attach spring and radius rods to 2" O.D. axles. For spring behind front axle suspensions. 3/8" thick steel, 5" eye to eye.

    Spring Behind Illustration (GIF)

     

  • Seals-It EAS1-05 Universal Inner Axle Seal for 2.5-2.75 Inch Tube
    Seals-It EAS1-05 Universal Inner Axle Seal for 2.5-2.75 Inch Tube
    (Part #9190970)
    x
                One size fits all! Fits any inner axle tube with an I.D. between 2-1/2" and 2-3/4". This eliminates ordering the wrong seal and allows you to always have the correct seal on hand. Typical applications* include Ford 9”, Quick change type rears, and 12 bolt GM. All seals are supplied with general installation guidelines. 
    • Inner Axle Seal I.D. = 7/8"
    • Axle sizes/Splines:  1-3/16” thru 1-1/2” / 28-31

     

    * Applications are reference only. Seals may be used on any rear end that is within the part number’s dimensional range. Rears can vary within a single model year and within the same model. Measure listed parameters before ordering.

  • Winters Performance 3748 Front Hub Shim
    New
    Winters Performance 3748 Front Hub Shim
    (Part #8023748)
    x
                

    These front hub shims from Winters performance must be used when using a double lip seal and oil in front hubs. This shim is sold individually.

     

     

  • Winters Quick Change Gears, 10 Spline
    From: $59.99
    Product Rating: 4.67 Stars
    Winters Quick Change Gears, 10 Spline
    (Part #80285)
    x
                
    • 8620 Steel
    • Heat Treated
    • CNC Machined
    • 10 spline
    • 1-1/4" Width

    Winters Quick Change Gear Chart

  • 1310 Series Chevy to Chevy U-Joint
    1310 Series Chevy to Chevy U-Joint
    (Part #91048315)
    x
                High quality, heat treated forged steel replacement U-joints. Comes with outside retaining clips.
            
  • Wide 5 Hub Seal
    $5.99
    Wide 5 Hub Seal
    (Part #912S23756)
    x
                
            

Filter

"Driveline and Axles" Page 1 of 50

Page 1 of 50

  • Winters Performance 6252 Pro-Eliminator Rearend Stationary Coupler
    Winters Performance 6252 Pro-Eliminator Rearend Stationary Coupler
    (Part #8026252)
    x
                

    These Pro-Eliminator rearend replacement parts are in stock and ready to order.

    • Stationary Coupler

    Quick Change Gear Sets, part number 91711-..., which is #41 on the diagram link below, are located elsewhere on this website.

    Note: This part is for sale because we either do not carry this product anymore or never have carried this brand/style before. Damages will be noted if applicable.

     Pro Eliminator Rear End Diagram (GIF)

  • Dana Spicer 5-1350X Heavy Duty Cross U-Joint, 1350 Series, Non-Greaseable
    Dana Spicer 5-1350X Heavy Duty Cross U-Joint, 1350 Series, Non-Greaseable
    (Part #910451350)
    x
                

    Premium Spicer Life Series® u-joints excel in performance and life. The journal crosses are cold-formed from high quality steel for maximum strength. Non-Greasable u-joints have Ample grease reservoirs in each trunion to assure effective lubrication and are pre-filled with high quality synthetic lithium grease providing superior friction reduction and higher temperature resistance. Spicer Life Series® u-joints use Spicer's highest quality, triple-lip seal along with an external seal guard to resist the harshest conditions. So when you replace your car or truck universal joints with genuine Spicer technology, you can rest assured that you are helping to ensure the maximum life for your vehicle.

    Non-Greasable u-joints are stronger than greaseable units since they don't have any grease passages in them.

    • Heavy Duty U-joint
    • 1350 Series
    • 3.625 x 1.188
    • Non-Greaseable cross shaft


  • Henchcraft Mini Sprint 1.5 Inch Left Rear Number 4 Wheel Spacer
    Henchcraft Mini Sprint 1.5 Inch Left Rear Number 4 Wheel Spacer
    (Part #9706880)
    x
                

    New from Henchcraft Chassis, these aluminum rear axle spacers are designed for 2" splined axles for Mini Lightning Sprint chassis.

    • Sized for proper component alignment
    • 1-1/2" left rear #4 spacer
    • For 2" splined axles
    • Aluminum construction
    • For use on Henchraft Mini Lightning Sprint chassis
  • Winters D-Mount Aluminum Front Hubs, RH/LH Rotor Mounts
    Winters D-Mount Aluminum Front Hubs, RH/LH Rotor Mounts
    (Part #80239802)
    x
                

    Winters direct mount front hubs are forged 2024-T3 aluminum for superior strength, durability and weight savings. Hubs are then CNC machined to precise tolerances. Gold anodized to resist corrosion.

    Kit includes bearings, seals, wheel studs, nuts, LH hub w/brake mount, RH hub w/ brake mount, and billet threaded hubcaps.

  • Dana Spicer 5-3615X U-Joint w/Coated Caps for Alum Driveshaft, 1350 Series
    Dana Spicer 5-3615X U-Joint w/Coated Caps for Alum Driveshaft, 1350 Series
    (Part #910453615)
    x
                

    Premium Spicer Life Series® u-joints excel in performance and life. The journal crosses are cold-formed from high quality steel for maximum strength. Non-Greasable u-joints have Ample grease reservoirs in each trunion to assure effective lubrication and are pre-filled with high quality synthetic lithium grease providing superior friction reduction and higher temperature resistance. Spicer Life Series® u-joints use Spicer's highest quality, triple-lip seal along with an external seal guard to resist the harshest conditions. So when you replace your car or truck universal joints with genuine Spicer technology, you can rest assured that you are helping to ensure the maximum life for your vehicle.

    Non-Greasable u-joints are stronger than greaseable units since they don't have any grease passages in them.

    • Coated Caps
    • 1350 Series
    • 3.625 x 1.188 
    • For use with Aluminum drive shafts
    • Non-Greaseable cross shaft


  • Axle Housing Inner Seal, 9 Inch Ford Grand National/Quick Change Rearends
    Axle Housing Inner Seal, 9 Inch Ford Grand National/Quick Change Rearends
    (Part #9190951)
    x
                

    High cornering forces can force the gear lube out of the center section and down the axle tube leaving the ring and pinion high and dry! This billet aluminum seal has three O-rings that seal it to the axle tube and two bonded, heavy duty, neoprene inner seals designed to compensate for any amount of axle shaft runout. Keeps gear oil in the center section. These seals will take up to an 1.5” diameter axle.

    • Anodized billet aluminum
    • A must for cambered rear ends
    • For 9" Ford Grand National and Quick Change type housings
    • For up to 1.5” diameter axle
    • Keeps gear oil in the center section
    • Outside Diameter: 2.56"
    • Overall Length: 1.50"
    • This seal will fit our steel wide 5 axle
    • Choose housing tube I.D. size needed:
      • 2.500" - Gold
      • 2.562" - Blue
      • 2.625" - Red
      • 2.750" - Silver

    919-0951 Instructions (PDF)

  • Bearing & Seal Kit for Brake Kit 910-31955
    Bearing & Seal Kit for Brake Kit 910-31955
    (Part #91031053)
    x
                Bearing & seal kit for GM Metric calipers & Mustang II rotors to 1949-54 Chevy spindle brake kit part 910-31955  &  910-31956. 

    Kit Includes:

    • Seals
    • Tapered inner bearing
    • Tapered outer bearing cones
    • Tapered outer bearing cups
  • New 9 Inch Ford Iron Carrier Housing w/3.062 Inch Caps
    New 9 Inch Ford Iron Carrier Housing w/3.062 Inch Caps
    (Part #91048390)
    x
                

    If you have built anything that has serious horsepower you know the weak link can be the stock Ford 9" carrier. The pinion area tends to be weak and if you throw enough power at it, it will break. That won't happen with this brand new housing. 

    This new cast iron housing is built to take street/strip abuse without the fear of breaking. Case has forged caps and extra beef where it's needed. Most stock differentials use the 3.062" o.d. bearings # TLM603049 w/ 1.781" i/d. You should also add a new heavy duty cast iron pinion support while you're at it. 

    • Forged Steel Caps
    • 1/2" Allen head grade 8 bolts
    • Heavy Duty Housing - 36 lbs.
    • Good for 1100 plus horsepower 
  • Winters Side Bell 6 Rib
    From: $244.99
    Winters Side Bell 6 Rib
    (Part #802K1663)
    x
                

    Winters Replacement Parts

    Speedway Motors has everyting you need to repair or upgrade your Winters quick change rearend. From center sections and gear sets to bearings, washers and O-Rings, we can help you get your rear back on the track!

    Winters Replacement Parts Figure (pdf)

  • Winters Performance 6746 Quick Change Standard Rear Cover
    Winters Performance 6746 Quick Change Standard Rear Cover
    (Part #8026746)
    x
                
    • Standard rear cover
    • Complete with bearings
  • Winters Performance 6818 Pro-Eliminator Midget Magnesium Gear Cover
    Winters Performance 6818 Pro-Eliminator Midget Magnesium Gear Cover
    (Part #8026718)
    x
                

    These Pro-Eliminator rear end replacement parts are in stock and ready to order.

    Pro Eliminator Rear End Part Guide (Link)

  • DMI RRC-1373 Vault-Lock Quick Change Sprint Rearend Gear Cover
    DMI RRC-1373 Vault-Lock Quick Change Sprint Rearend Gear Cover
    (Part #9401373)
    x
                

    The Vault-Lock rearend gear cover turns timely gear changes into a 15 second job!  These covers eliminate the process of having to remove and reinstall the 6 outside cover bolts by utilizing the patent pending center Vault-Lock design.  Designed to fit Winters or DMI rearends.

    • Speed-up gear change time with the Vault-Lock gear cover
    • Fits Winters Performance or DMI rearends
Goto Previous PagePrevious Page
1 2 3 4 5 ... 50