Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products

Hook up that horsepower with driveline parts from Speedway Motors. Whether you're racing at your local dirt track, at the drag strip or just have a monster under the hood of your hot rod, we have the parts and technical know-how to help you put the power to the ground.

"Driveline and Axles, Driveshaft" Page 1 of 4

  • Winters Performance 7605 Pro-Eliminator Drive Shaft Snap Ring
    Winters Performance 7605 Pro-Eliminator Drive Shaft Snap Ring
    x
                

    These Pro-Eliminator rearend replacement parts are in stock and ready to order.

    • Driveshaft Snap Ring

    Quick Change Gear Sets, part number 91711-..., which is #41 on the diagram link below, are located elsewhere on this website.

    Note: This part is for sale because we either do not carry this product anymore or never have carried this brand/style before. Damages will be noted if applicable.

     Pro Eliminator Rear End Diagram (GIF)

  • MPD Racing 68002/68102 Mag Housing and Ring
    MPD Racing 68002/68102 Mag Housing and Ring
    x
                

     For Sprint Car Drive Lines Only. Will not fit Midgets

    • Will fit MPD 4.45" diameter balls
    • Weighs only 2.15 lbs
  • Winters Performance 5003 Heat Treated Lower Shaft, 19-1/2 Inch
    Winters Performance 5003 Heat Treated Lower Shaft, 19-1/2 Inch
    x
                

    Winters Replacement Parts

    Speedway Motors has everyting you need to repair or upgrade your Winters quick change rearend. From center sections and gear sets to bearings, washers and O-Rings, we can help you get your rear back on the track!

    Winters Replacement Parts Figure (pdf)

  • Speedway Steel Drive Shaft
    $89.99
    Product Rating: 4.21 Stars
    Speedway Steel Drive Shaft
    x
                

    Lightweight steel driveshaft lengths measured from center of U-joint to center of U-joint. Driveshafts are not dynamically balanced. We recommend dynamically balancing the driveshaft prior to installation. Several lengths are available.

    • Super strong and much lighter
    • 2" O.D. tubing with .083" wall
    • Forged yokes
    • Painted white for high visibility on the track
    • Fits most IMCA modifieds

    U-joint # 91048315 works for the front U-joint position on these driveshafts and with the front yokes we sell. Any of the three U-joints listed will work on the rear U-joint location based on rear axle requirement.

  • Seals-It TBS2A-07 Complete Torque Ball Seal Kit
    Seals-It TBS2A-07 Complete Torque Ball Seal Kit
    x
                This seal kit fits in the motor plate hole and helps keep dirt out of the U-joint and torque tube.  
            
  • Drive Shaft Safety Loop
    $29.99
    Product Rating: 4.50 Stars
    Drive Shaft Safety Loop
    x
                This driveshaft safety loop holds the drive shaft in place in case of universal joint failure. Made from 2" x 1⁄4" hot rolled steel with grade 5 bolts. Bolt-on installation.
            
  • GM Front Slip Yoke, 5 1/2 Inch
    GM Front Slip Yoke, 5 1/2 Inch
    x
                

    Stock length (5-1/2") slip yoke for GM applications with 1-3/16" x 27-spline output shaft. Works with 1310 series U-joints.

    • This yoke measures 5-1/2" from tip to centerline of u-joint
    • This yoke is grooved for an "external" u-joint cap retaining clip
    • The machined length on the yoke is 3-3/4"

    The expressed measurement or length of the slip yoke is taken from the center of the u-joint to tip, not overall. 

    Fits over the output shaft of the following transmissions: 

    • Common GM/Saginaw 3 & 4 speed transmissions with a 1-3/16" x 27 spline output shaft
    • Powerglide, T-350, 700R-4, 200R-4, and 4L60 automatic transmissions
    • Muncie M20/M21 and Borg Warner T-5, T-10 & T-56 27-spline manual transmissions
  • Winters Performance 6661-02 Standard Weight Torque Tube
    Winters Performance 6661-02 Standard Weight Torque Tube
    x
                This Winters Aluminum Torque Tube features an aluminum collar and 3" diameter tube. Assembly is 28" in length from mount face to the end of the tube. Must be cut to desired length.  
            
  • 9 Inch Ford Small Yoke
    $64.99
    $74.99
    Product Rating: 5.00 Stars
    9 Inch Ford Small Yoke
    x
                We found a limited supply of new small yokes for the 9" Ford.  They accept the 1310 series U-joints (1-1/16" caps x 3-7/32").  Fits standard 28 spline pinion gear.
            
  • Stallard Chassis BC250-540 Sprocket Carrier and Rotor Hub
    Stallard Chassis BC250-540 Sprocket Carrier and Rotor Hub
    x
                
    • Fits any 1.75” x 27 spline rear axle
    • Use the same hub for drive sprocket or brake rotor
    • 5.25” bolt circle with six threaded ¼ x 20 mounting holes
  • DMI RRC-1400 XR-1 Bulldog Rearend Integral 10-10 Coupler
    DMI RRC-1400 XR-1 Bulldog Rearend Integral 10-10 Coupler
    x
                

    Manufactured with the highest quality castings, bearings, and gears these rearend parts have proven reliability.

    Integral 10-10 Coupler

  • 1310 Series Chevy to Chevy U-Joint
    1310 Series Chevy to Chevy U-Joint
    x
                High quality, heat treated forged steel replacement U-joints. Comes with outside retaining clips.
            
  • Tru-Lite Titanium Torque Tube Stud Kits
    Tru-Lite Titanium Torque Tube Stud Kits
    x
                These titanium stud kits are designed to attach torque tubes to Sprint rear ends. Each titanium stud features fine thread on one end and coarse thread on the other. 
    • 3/8"-16-24 x 1.8" RH male
    • Kits contain 6 studs, jet nuts and washers
    • Titanium standard
    • Fits any brand rear end
    • Strong, durable and easy to install
  • Billet U-Bolt Strap Kit, 1-1/8 Inch
    Billet U-Bolt Strap Kit, 1-1/8 Inch
    x
                

    NEVER OVERTIGHTEN U-BOLTS AGAIN !! 

    These universal billet strap kits fit 1330 U-Joint, Steel Girdle, Ford 9 inch.  They include case hardened bolts, nuts, flat and lock washers.

    • Billet strap kit
    • Fit 1330 U-Joint, Steel Girdle, Ford 9 inch
    • Include case hardened bolts, nuts, flat and lock washers
  • Mini-Sprint Aluminum Rear Sprocket, 6.438 Inch Bolt Circle
    Mini-Sprint Aluminum Rear Sprocket, 6.438 Inch Bolt Circle
    x
                These lightweight 7075-T6 aluminum sprockets for Mini/Micro Sprints fit 6-lug hubs with the 6.438" bolt circle. Available from 42-55 tooth.
            
  • DMI SRC2430 Hollow Steel Drive Shaft
    DMI SRC2430 Hollow Steel Drive Shaft
    x
                
    This DMI hollow driveshaft is specifically designed out of steel to be very lightweight. This drive shaft will fit an internal coupler or external coupler by Winters, DMI, Franklin, ect.
    • Lightweight
    • Specially designed and engineered
    • 10-16 spline
  • 1999-2012 Yamaha R6 Steel Counter Sprocket
    1999-2012 Yamaha R6 Steel Counter Sprocket
    x
                1999 - 2012 Yamaha R6 steel counter sprocket.
            
  • Butlerbuilt Torque Tube Pad
    $49.99
    Butlerbuilt Torque Tube Pad
    x
                

    Protect your ankles in violent crashes by wrapping your torque tube with this flame retardant pad.  Installs and removes in seconds and is intended to work with existing torque blankets and scatter guards.

  • 1310 / 1350 Series Chevy to Ford U-Joint
    1310 / 1350 Series Chevy to Ford U-Joint
    x
                High quality, heat treated forged steel replacement U-joints. The endcaps on the 3-5/8" width side have grooves for "inside clips." There are no grooves on the 3-7/32" width endcaps, therefore that side MUST use external clips. All four clips included.
            
  • Speedway Steel Drive Shaft, 52-1/2 Inch
    Speedway Steel Drive Shaft, 52-1/2 Inch
    x
                

    Lightweight steel driveshaft lengths measured from center of U-joint to center of U-joint. Drive shafts are not dynamically balanced. We recommend dynamically balancing the driveshaft prior to installation. Several lengths are available.

    • Super strong and much lighter
    • 2-1/2" O.D. tubing
    • Forged yokes
    • Fits most IMCA modifieds

    U-joint # 91048315 works for the front U-joint position on these driveshafts and with the front yokes we sell. Any of the three U-joints listed will work on the rear U-joint location based on rear axle requirement.

  • Stallard Chassis Micro Sprint Chain Guide Assembly Kit
    Stallard Chassis Micro Sprint Chain Guide Assembly Kit
    x
                These chain guide assembly kits work with Micro Sprint applications and are designed to fit 2009-later Stallard chassis.  They feature aluminum construction with a black anodized finish and come complete with block plate, mounting plate, and chain guide block.
    • Complete assembly includes block plate, mounting plate and chain guide block
    • Aluminum construction, black anodize finish
    • Fits 2009-later Stallard chassis
  • Simpson 31023BK 3 Inch Torque Tube Restraining Strap
    Simpson 31023BK 3 Inch Torque Tube Restraining Strap
    x
                

    Simpson Racing is all about Racers Safety, Sometimes a torque tube hoop does not justify so use this torque tube restraining strap.

     

    • For 3" torque tube.

     

  • Ford 9 Inch Long Wide Steel Yoke, 1-1/8 Inch Cap Diameter
    Ford 9 Inch Long Wide Steel Yoke, 1-1/8 Inch Cap Diameter
    x
                

    These are long wide steel yokes with 1-1/8" cap diameter and 4-1/4" yoke height.  They fit Ford 9" with 1330 U-joint and 28 spline.  The mounted lenght on these yokes is 4.33" and the overall lenght is 5.09".  These steel yokes feature a natural finish.

    • 1-1/8" cap diameter
    • 4-1/4" yoke height
    • Mounted lenght: 4.33"
    • Overall lenght: 5.09"
    • Natural finish
    • Steel
    • Fits Ford 9" with 1330 U-joint and 28 spline

     

  • GM Front Slip Yoke, 8 Inch
    $69.99
    $79.99
    Product Rating: 5.00 Stars
    GM Front Slip Yoke, 8 Inch
    x
                

    Longer slip yokes help compensate for extreme travel rear suspension set-ups or driveshaft lengths slightly shorter than needed. Yoke is grooved for "external" snap rings to retain U-joint cups. Works with 1310 series U-joints.

    Fits over the output shaft of the following transmissions: 

    • Common GM/Saginaw 3 & 4 speed transmissions with a 1-3/16" x 27 spline output shaft
    • Powerglide, T-350, 700R-4, 200R-4, and 4L60 automatic transmissions
    • Muncie M20/M21 and Borg Warner T-5, T-10 & T-56 27-spline manual transmissions
  • M&W Micro Sprint Nylon Sprocket Hub Chain Guard
    M&W Micro Sprint Nylon Sprocket Hub Chain Guard
    x
                These nylon sprocket hub chain guards from M&W Aluminum Products are perfect for your micro/mini sprint race car.  They are a replacement for our 27-spline quick change sprocket carriers and they bolt directly to your sprocket.
    • For 27-spline quick change sprocket carriers
    • Black nylon
    • Direct replacement for white nylon chain guard (part number; 960-1300)
    • Choose from 5.25" or 6.438" inside diameter
  • 1310 / 1330 Series Chevy to Ford U-Joint
    1310 / 1330 Series Chevy to Ford U-Joint
    x
                

    High quality, heat treated forged steel replacement U-joints. This u-joint only works with clips outside the end caps. Clips included. The caps do not have grooves for clips.

  • Fast Shafts Steel Drive Shaft
    $149.99
    Product Rating: 4.50 Stars
    Fast Shafts Steel Drive Shaft
    x
                

    Fast Shafts are built using only the best DOM 1020 "Drive Shaft Quality" tubing on the market. All Fastshafts driveshafts are balanced using only the finest balancing equipment.

    • 2" OD x .120 wall
    • Driveshafts are balanced and include 1310 series U-joints
    • Available in 28", 29", 31" and 32.5"
  • DMI SRC-2305 Ankle Saver Steel Torque Ball Housing
    DMI SRC-2305 Ankle Saver Steel Torque Ball Housing
    x
                Not much to say here. More power, tacky track, failed u-joint... ouch! This steel torque ball housing will save you some pain. 3.46 lbs.  
            
  • M&W SG-525-2 Micro/Mini/600 Sprocket Guard, 5.25 Inch Bolt Circle
    M&W SG-525-2 Micro/Mini/600 Sprocket Guard, 5.25 Inch Bolt Circle
    x
                Use these on both sides of your sprocket hub as a chain guide and protection against debris.
            
  • Winters Performance 3942-03/9105 27-1/4 32-Spline Ball Drive Shaft Kit
    Winters Performance 3942-03/9105 27-1/4 32-Spline Ball Drive Shaft Kit
    x
                Reduce deflection and eliminate bind with this new driveline development.  Lighter than many titanium drive shafts, this large OD shaft offers the swivel ball system with 32 splines on each end.  Non-swivel style rearends can be upgraded to accept this driveshaft.
            
  • Winters Hercules Sprint U-Joint
    Winters Hercules Sprint U-Joint
    x
                The latest development in U-Joint technology, Hercules is the answer to driveline failure. Billet 7075 aluminum captures the journal while U-bolts hold it securely. Weighs only 3.8 lbs and is available in both 16 or 32 spline. 
            
  • MPD Racing 02160030 Midget 2.3 Inch O.D. Torque Tube
    MPD Racing 02160030 Midget 2.3 Inch O.D. Torque Tube
    x
                Midget torque tube and collar by MPD Racing. Will work with any ball and housing, it is a midget drive line only.
            
Goto Previous PagePrevious Page
1 2 3 4