Speedway Motors is the source for all your classic pickup truck parts. No matter whether you're wrenching on a half ton Ford F100, Chevy 3100, or Chevy C10, we can help you build the truck of your dreams. Also, for those of you who drive Chevy S10 or diesel trucks, Speedway Motors has your lowering kits, drop spindles, V8 swap kits, tuners, modules, and cat-back exhaust systems too.
This harness was designed to offer you all the highest quality components in a package designed for cars with minimum accessories. Each wire is color coded and labeled every few inches.
Our prewired 12 circuit kit will fit all your basic needs and makes wiring a painless process. It is designed especially for the street rod without accessories. It also includes horn relay and connector, turn and hazard signals, dimmer switch connector, circuit breaker for headlights, two flashers, one alternator plug, two ignition switch connectors, plus more.
- Mainfuse box base is 1-7/8" x 3-11/16"
- Box height is 3-3/4"
Speedway’s line of universal Chevy radiators makes it easy for budget-minded racers to get a professional-quality aluminum racing radiator. These high performance radiators feature furnace-brazed construction, two rows of large 1" aluminum tubes, billet filler necks and a maximum number of fins per inch for great heat transfer. They are not available with transmission coolers and they do not come with mounting brackets.
These Chevy-style radiators have driver’s side upper inlets, passenger side lower outlets, and can be ordered in a variety of custom widths.
- All-aluminum, furnace-brazed construction
- No cheap epoxy glue or crimped in gaskets
- Maximum amount of fins per inch allows greater heat transfer
- Billet filler necks
- Available in 22", 24", 28", or 31" widths (measurements include tanks)
Learn more about how radiators work and selecting the proper radiator for your vehicle by reading our tech article, Radiator Cooling Performance.
Rebuilt 1969-77 mid and full size caliper. 7/16"-20 inlet so you can use the readily available brake hoses and hardware from Pre-1978 GM midsize cars. IMCA approved.
No core charge required. Fits 1" thick rotor. 2.8" diameter pistons installed. It has 7-1/16" center to center mounting holes. The width between mounting tabs is 2-3/4".
These stock replacement single piston Metric calipers were standard equipment on 1978-88 GM mid-size cars (Cutlass, Grand Prix, Regals, Monte Carlo, etc.). They feature a 2.38" single piston, shielded bottom inlet, and will save 3-1/2 lbs. per side compared to mid-size 1969-1977 caliper.
- IMCA approved
- No core charge required
- 7/16"-20 inlet
- Can be used with brake hoses from Pre-1978 GM intermediate cars
- Brake pads & bolts sold separately
Note: Does NOT include brake pads or slider bolts and bushings.
Speedway Motors now offers you a 9" Ford street 3rd member for your street rod. We reclaim genuine Ford 9" housings, clean, inspect and install all new components. All bearings, seals, 1310 series yoke and ring & pinion are new!
These Ford 9" 3rd member assemblies feature new Pro Gears ring & pinion, choice of 3.50, 3.70, 3.89, 4.11 or 4.56, Currie 9-Plus limited slip differential, 28 or 31 spline. Shipped in handy plastic carrying case. Assembled by professionals.
910-48345 Instructions (PDF)
Fits aftermarket Mustang II crossmembers. Available in manual or power steering. Mount bushings are included with the Power version, but mount bushings are NOT included in the Manual version.
MANUAL: New manual rack and pinion steering assembly for Pinto/Bobcat/Mustang II based front suspensions in street rods and kit cars. 9/16"-26 spline input shaft. 16" mount centers.
POWER: Rebuilt power rack from 1982-88 T-bird. Also fits aftermarket Mustang II crossmembers. Bushings included. (Can be used with a Saginaw GM power steering pump without any additional valves or inline pressure regulators). Overall width is 45-1/8" with 15-1/2" mount centers. Must use offset bushings (910-34342) to mount to original Mustang II crossmembers. 3/4"-36 spline input shaft.
Speedway Motors now offers a reproduction version of one of the most popular carburetors ever used, the original Stromberg 97! Original equipment on '30s and '40s cars and trucks, the Stromberg 97 has long been favored by flathead hot rodders and racers who realized the performance qualities of this timeless fuel supplier.
There have been numerous attempts to reproduce this unit, with little success. "Speedy" Bill Smith of Speedway Motors in Lincoln, Nebraska, took on the challenge to make a great product even better. The 9 Super 7 ® Carb brings this reproduction of the original Stromberg 97 2 barrel carb into the 21st Century!
Speedway Motors has incorporated all of the improvements shown above while maintaining the carburetor's original look. Features such as the choke assembly, accelerator pump, main jets and cosmetics have all been faithfully retained. Additionally, each carburetor is individually flow tested and inspected for leaks. Perfection is the result!
Aesthetically, the 9Super7 is nearly identical to the stock unit, minus the large 97 logo that appeared on the side and the patent numbers found on the float bowl area. Upgraded internal parts include; the float, needle, and seat. Jetting and power valve settings remain as they were for the original 97 carbs as well as the cfm and vacuum specs.
The other similarity that the 9 Super 7 shares with the original 97 is the setup and tuning necessary to yield a well-running machine. While perhaps not as simple as bolting on a single four-barrel, the 9 Super 7 makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required is an intake, a linkage system, a Uni-Syn syncing tool, and a little patience. Be sure to include the Secondary 9 Super 7 when installing multi-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs. See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb set-up.
- All-new tooling for crisp, flawless castings
- New aluminum base assembly allows for cooler fuel temps and better fuel efficiency as compared to the original cast iron design
- Stainless steel screws and hardware
- Choke assembly, accelerator pump, and jets have all been faithfully retained and accept standard Stromberg parts
- Features original Stromberg 0.97" venturi diameter
- Modern Nitrophyl float and Neoprene gaskets
- Original troublesome needle and seat replaced by a Grose-style fuel inlet valve to better cope with higher fuel pressures and improved high speed running
- Will not stick or dribble like the old Viton-tipped needle and seat setups
- Grose-style jet valve won't corrode in modern fuel, something the original needle and seat units can't do
- Comes with a No. 65 power valve and 0.045" main jets, identical to the stock 97
- Extended brass throttle shaft to simplify multi-carb linkage
Whether you're building an option loaded car or just want to have extra circuits available for future updates, this harness is perfect and makes any job painless. Compact 5-1/2"L x 4-1/2"W x 3-1/4"H fuse block holds 18 standard push-in fuses and can be mounted almost anywhere.
Each high temperature wire is color coded and labeled every six inches. Also includes GM type steering column connectors. To keep costs down and the quality high, this harness does not include any switches, light sockets or plugs that you would normally already have.
- Harness has 20 circuits, of which 18 are fused
- Taillight leads measure 17' long
- Includes plug for GM column, headlight switch, dimmer switch, and signal flashers
"Classic Truck" Page 1 of 25
$29.99More InfoSpeedway Fuel Level Gauge with Sender, 2-1/16 Inchx
These fuel level gauge/sender kits feature a domed lens and a stainless steel bezel and a backlit white face. The fuel sender comes with seal and and all mounting hardware.
- Overall Diameter: 2.25"
- Overall Length: 9.25"
- Includes sender
- 240 ohms empty, 33 ohms full
- Stainless steel bezel
- Backlit white face
Learn more about selecting the proper fuel sending unit by reading our tech article, Fuel Sending Units.
$59.99$73.99More InfoAuto Meter 201009 Cobra Voltmeter Gauge, Short Sweep Electric, 2 Inchx
This vintage instrument series is designed to accurately re-create the period correct details of the instruments used in the original Cobra Roadster while incorporating the latest technology advancements in performance gauges from Auto Meter. These black dial face instruments feature incandescent through the dial backlighting with white pointers, traditional numbers and tick marks, and are finished with flat glass and scalloped chrome bezels.
- Short Sweep Electric Voltmeter
- 8-18 V
- Mounts in 2-1/16" Hole
- Includes mounting hardware and Incandescent Backlighting
- Requires 18 gauge electrical wire and ring or spade terminal connections for installation (not included)
$19.99$26.95More InfoLokar SG-6009 Chrome Dimmer Switch Cover, Chevy/Fordx
Brighten up that old dimmer switch with one of these new dimmer switch covers from Lokar! Made from steel and feature a beautiful chrome finish and a textured rubber pad.
$759.99$799.95More InfoAeromotive 18664 Stealth Fuel Cell, 15 Gallonx
Finally, a truly universal system that is built for street rods, drag racing, off-road, autocross, drifting and any other performance application you can think of! This complete unit has all the advantages of an in-tank fuel system; quiet cool operation, ideal fuel pump environments and a serious reduction in installation time and investment. In addition, this system eliminates the risk of fuel pump cavitation due to hard cornering, launching or braking thanks to innovative baffling built into each tank.
- Includes Stealth 340 LPH in-tank fuel pump
- Works with both carbureted and EFI systems
- Return line provisions
- Two AN8 vents with rollover valves
- Universal 0-90 Ohm fuel level sender
- Standard 12-bolt flush mount lid assembly
- Natural aluminum finish
- Ready to go simple installation
Fuel Pump Flow Chart (GIF)
$19.99More InfoTCI 745504 Midplate Spacer Kit, 1/4 Inch Thickx
TCI® Seven, Eight, Nine and Ten inch Race Torque Converters are designed to allow use with or without a midplate. The converter has the stock length nose piece. By removing the sleeve on the pilot, you can use this 1/4" extension.
- 1 - Pilot Extension
- 3 - 1/4" Washers
- 3 - Long converter bolts
$174.99$179.95More InfoAeromotive 11140 340 Stealth Fuel Pump, Centered Inletx
The Aeromotive 340 Stealth Fuel Pump is a high-output, in-tank, electric fuel pump that fits most popular EFI applications. It is a compact, lightweight pump that bolts into many existing hanger assemblies.
What sets the 340 Stealth Pump apart is its superior flow throughout a wide pressure range. Compared to other popular aftermarket pumps, at 40 psi the 340 boasts more than 340 lph. That’s over 30% more flow, making it ideal for applications requiring more flow while retaining the factory lines and mounting provisions available in the OE configuration. The 340 is also perfect for use as a universal replacement for applications that require more flow to support forced air power adders such as turbo and supercharged applications.
- Fits most vehicles where popular aftermarket pumps are applicable
- Designed for in-tank use only
- Can be used in carbureted or EFI applications
- Turbine pump mechanism increases durability and can be used in pulse modulated applications
910-11140 Instructions (PDF)
Modern Driveline Reverse Switch Harness for GM T5 and T56 Transmissionsx
These harnesses for transmission neutral safety switch/reverse light switches are designed for use with GM T5 and T56 transmissions.
- Factory style
- For GM T5 and T56 transmissions
$739.99$799.99More InfoClassic Instruments Speedometer Gauge Set, V8 Speedster Facex
Tom Gale, formerly Chief Designer of the Daimler Chrysler Corporation, has led the Classic Instruments design team in the production of a beautiful new series. Designed with unique dial faces that are spun and engine turned aluminum. The pointers for this series is a new design and each pointer is chrome painted. The face has a chrome V8 emblem signifying American Hot Rod Heritage. The light diffusers have laser etched indices lining up with the indices on the gauge faces.
The V8 Red Steelie series features a vivid red background with spun aluminum numbers and accent graphics that brightly bounce off the red background. The series also features the uniquely designed pointer for the V8 line which is chrome plated and balanced for precision accuracy. Additional details within the instruments are laser etched markings on the light diffuser ring which add a level of dimension and functionality. The etching corresponds with the indices on the face and flow into a polished stainless high step bezel that is crimped around a optic grade curved lens to complete the overall design.
- Black "V8 Speedster" face design or Red "V8 Red Steelie" face design
- Kit includes 3-3/8" Speedo & Tach, 2-1/8" Fuel, Oil, Temp, Volts
- Standard GM sender pack included
$44.99$49.99More Info3X Chemistry Satin Rust Encapsulator, Quartx
3X:Chemistry Encapsulator is a single component, high solids paint specially formulated to bond to blasted or rusted metal surfaces. The coating forms a rock hard finish that's flexible, non-porous and will not crack, chip, flake or peel. No hardeners or activators are needed. Encapsulator is completely unaffected by salt, gasoline, oils, battery acids, hydraulic fluids, solvents, chemicals, or corrosives.
- Permanently stops rust and corrosion
- Can be sprayed or brushed over rusted surfaces
- Reusable after opening
- Highest percentage of solids
- Available in Satin
$103.99More InfoWaterman 935566D Dash Mount Fuel Shut Off Valve, -6 ANx
Dash mount is AN6 male with offset style handle. Fuel cell ball valve mounts in plate. Required for many Sprint cars. They are designed to be plumbed inline and mount close to the driver.
- Engineered specifically for sprint car applications
- -6 AN male to male fuel shut off valve
- Designed to be plumbed inline and mount close to the driver
$10.99$14.99More InfoCON2R 7-002 Chrome Wing Nut, 1/4-20 Thread, 2-1/4 Across, 1-1/2 Tallx
This wing nut is for-sure an attention getter. Perfect topper for the air cleaner on a big four barrel, on top of your tri-power pots or an accent piece wherever you need it.
$18.99$19.99More InfoStainless Steel Beauty Ring for 15 Inch GM Rally Wheel, 2.5 Inch Widex
Modeled after 70's GM factory equipped rally wheel beauty rings. They are designed to fit our GM Style Rally Wheels.
- 15" x 2.5" stainless steel trim ring
- For use on 7" rim
- Perfect finishing touch to our GM Style Rally Wheels
$6.99$7.99More InfoSpeedway Extreme Gaskets, 2-1/2 Inch Collector Gasketsx
- Reusable triple-layer gasket
- Stainless steel with a heat-resistant, rubber-based inner core
- 0.085” thick, ultra pliable
- Easily conforms to surface irregularities to create a tight, leak-proof seal
$51.99$68.80More InfoDEi 010502 Protect-A-Boot Spark Plug Boot Heat Shield, 6 Inch, Silver, 8 Packx
Protect-A-Boots are made from a high temperature resistant glass fiber material and treated with a proprietary coating, Protect-A-Boots provide spark plug boot and wire protection from extreme under hood heat.
- Double-wall construction for added durability
- Helps prevent burn-through, hardening and cracking of boots
- Installs in seconds
- Universal-fits most straight or angled boots
- Withstands 1200°F direct continuous heat
- Non-flammable & protects against chemicals & resists water
$48.99$65.88More InfoDEi 010393 Reflect-A-GOLD Heat Reflective Tape, 24 x 24 Inch Sheetx
Reflect-A-GOLD is a metalized polyamide polymer laminated glass cloth with a high temperature pressure sensitive adhesive for use in extreme temperature swing environments. It is lightweight and easy to apply and remove.
Highly effective material for firewalls, fuel cells, engine covers, under hoods, engine compartment, bulk heads, seat bottoms – anything or area that needs protection from heat.
- For firewalls, bulkheads, engine covers, floors, seat bottoms & more
- Capable of handling continual temperatures up to 850°F
- Resists UV degradation for long-term performance
- Virtually NO clearance needed
- Adhesive protected by a release liner rated up to 325°F
- Light weight and flexible-Trim to size
- Space age polymer material
- Reflects up to 850°F! Reflecting 80% of heat!
- Ultra light weight and self adhesive
FlatStoppers were developed as a solution for people having problems with tires developing flat spots when a vehicle is parked for 30 days or longer. Once tires are set on FlatStoppers (on a level surface), they settle into the pad's concave depression, which helps support more of
the tire. This disperses the weight of the car more evenly onto the tire - helping to prevent any flat spotting. The pads measure 22.3" long x 3.5" high x 14" wide, and will accommodate tires up to 12" wide.
FlatStoppers will not conduct heat or cold into your tires despite changing floor temperatures.
Flatstoppers are made with the company's patented super-lightweight 100% solid construction technique - making them highly durable, virtually indestructible, and providing a 6,000 lb. vehicle weight capacity. FlatStoppers' textured coating prevents sliding across floors - including epoxy-coated floors and RaceDeck.
FlatStoppers won't scratch or otherwise damage floors, and won't rust.
$14.99$19.97More InfoTitan Tools 51503 Mini Tubing Benderx
- Bends 1/8, 3/16, and 1/4" tubing up to 90 degrees
- Use with Brass, Copper, Steel, or Aluminum
- Compact for limited accessibility applications
$74.99$87.95More InfoLokar TC-1000LS160 Hi-Tech LS1 / 350 Ramjet Throttle Cable, 60 Inchx
Lokar Hi-Tech Throttle Cable features a stainless steel braided housing. They are designed with a specially extruded liner for extended life of the cable – not to be confused with ordinary braided brake hose. Cables are equipped with aluminum fittings and aluminum ferrules to eliminate fraying.
Kits come complete with installation instructions.
$8.99$11.45More InfoDEi 050371 Boom Mat Speaker Baffle, 6 X 8 Inch Oval Slimx
Please view the product's page for more information
$159.99$179.99More InfoRapidAir M3800 Master Air Line Kit, 1/2 Inch Linex
These airline kits work great for your workshop with applications from automotive to woodworking. This is a complete compressed air distribution system that is designed to easily install within new walls or on wall surfaces of existing workshops/garages. These kits allow you to put air lines exactly where you want them, just like electrical outlets. No more dragging hoses across the shop to your work area. No special tools required, simply push the flexible tubing into the fittings and put up your system in an afternoon.
- 1/2" line
- Operating pressure: 175psi at 70° F / 140psi at 140° F
- Meets OSHA guidelines
- Temperature range: -40° F to 140° F
- Compatible with common compressor oils
- 100 ft. of 1/2" ID Tubing
- 3 Outlets
- 1 Manifold
- 5 Elbows
- 1 Tee
- Tools (air chuck & filter regulator sold separately)
$7.99More Info3/8 X 3/8 Clevisx
The correct clevis for mounting our rack and pinion units (668-0105 & 668-0115).
$24.99More InfoBook/Manual - How To Swap GM LS-Series Engines Into Almost Anythingx
How to Swap GM LS-Series Engines into Almost Anything shows how to fit these powerhouse engines into popular GM F-Body cars, such as the Camaro and Firebird, and also how to install these powerplants into non-GM muscle cars, sports cars, trucks, and of course, hot rods. This book includes a historical review, complete specs, and detailed information so you can select and fit the best LS engine for a particular vehicle and application.
A section on mounting kits, explaining how to install these engines into a variety of cars using readily available motor mount kits, universal engine mounts, or fabricated mounts. In addition, the book shows you how to perform necessary oil-pan modifications and adapt accessory drivers as well as choose the most suitable fuel pump, exhaust system, wiring harness, and electronic control module. This guide takes it a step further, revealing how to select the best reprogramming equipment and software for a vehicle and its application. Finally, the book covers the range of compatible transmissions for LS engines.
- By Jefferson Bryant
- 144 pages
- Photos: 375 color
- Sold individually
$5.99More InfoSwindell Series Sprint Car Set-Up Sheetsx
- Can be used if running a 305, 360 or 410 sprint car
- 1 tablet contains 50 sheets
- Easily organize your set-up notes for each race
- Gives you a permanent record of every adjustment and set-up
- Designed and used by World of Outlaw and Chili Bowl Champion Sammy Swindell
$4.99More InfoSpeedway Tire Coaster Setx
- Made from 100% recycled tire rubber
- Set of four
- Four distinct designs in each set
- Vintage Sprint Mag
- Kustom Cross-bar Flipper Cap
- D-hole Stock Car Wheel
- Redline 5 Spoke Mag
From: $5.99More InfoNewStainless Steel Tooth Black Tie Wraps, 100 per Bagx
These zip ties are made in the U.S.A. and feature a stainless steel securing tooth. They come 100 to a package and are perfect for securing loose wiring and hoses or can help serve as temporary fixes to many odd jobs and projects.
- Stainless Tooth Tie Wraps feature super strong self-locking, stainless steel tooth, one piece design, standard size head.
- Black Tie Wraps are UV resistant. Recommended for outdoor usage.
- Metal Detectable
- Temperature Ratings 185 F / 85 C.
- UL Flame Rating 94V-2.
- Minimum installation temperature is greater than 32 F or 0 C.
- Made From Nylon 6/6.
- Choose from lengths of 4", 5.5", 7.3", and 11.4"
- 100 per Bag
$324.99More InfoBare 60 Inch Centered 9 Inch Ford Housingx
Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 60" from hub-to-hub. You will need one 28-3/8" long axle and one 30-5/8" long axle. Includes 8 T-bolts for the axle bearing retainer plates and 10 studs for the 3rd member.
Third member sold separately.
$124.99$139.99More InfoRapidAir M6030 100 FT Maxline Nylon Air Hose Tubing, 3/4 Inch Diameterx
These airline kits work great for your workshop with applications from automotive to woodworking. This is just the airline for your compressed air distribution system that is designed to easily install within new walls or on wall surfaces of existing workshops/garages. You can put these air lines exactly where you want them, just like electrical outlets. No more dragging hoses across the shop to your work area. No special tools required, simply push the flexible tubing into your fittings (sold separately) and put up your system in an afternoon.
- 3/4" line
- Operating pressure: 175psi at 70° F / 140psi at 140° F
- Meets OSHA guidelines
- Temperature range: -40° F to 140° F
- Compatible with common compressor oils
- 100 ft. of 3/4" ID Tubing
$239.99More InfoDeluxe 45 Degree Brake Flaring Toolx
- Easily form 45-degree double, single and bubble flares in OE steel, stainless steel and soft metal tubing
- For use with 3/16"-, 1/4"-, 5/16"- and 3/8"-diameter lines
- Turret-style design allows you to make those precision flares in minimal time
- All the brake-flaring forming dies you need are mounted right on the turret
- T-handle screw clamp securely holds your line in place during forming
- Packaged in a blow-molded case
Learn more about flaring lines for our automotive fittings by reading our tech article. The Principles of Automotive Fittings.
$399.99More InfoDougs Headers DEC300A Stainless Steel Electric Exhaust Cut-Outs-3 Inchx
These rugged Doug's Headers electric exhaust cutouts allow you to convert to a wide-open, unobstructed exhaust system with the flip of a dash-mounted switch. Doug's electric exhaust cutouts are built to last; they feature full stainless steel construction with a heavy-duty Dayton gear reduction rack and pinion electric drive mechanism. Best of all, these cutouts use a self-cleaning, knife-edge seat for a leakproof seal every time, whether open or closed. Doug's Headers electric exhaust cutouts include a pre-wired harness, a toggle switch, and fuses for an easy installation.
- 3.000 in.
- Stainless steel
- Sold as a pair
- Includes wiring harness
$9.99More InfoTaylor 20314 14 Inch Braided Grounding Strap Cablex
These braided grounding straps from Taylor Cable are 14" long 4-gauge and feature tin coated copper construction.
- 14" long
- 1" wide
- Tin coated copper
$16.99More InfoCombo Exhaust Bend, 2-1/2 Inch Diameterx
These mild steel combo exhaust bends are perfect for building or repairing headers. They feature smooth mandrel bends with a bend radius of 7" and an outside diameter of 2-1/2".
- Mild steel
- For building or repairing headers
- 16-gauge (0.06" thick)
- 2-1/2" O.D
Metal Pegboard Tool Organizer, 32 x 32 Inch Wall Control Storage Systemx
Durable, all-steel construction will not warp, fray or crack. Attractive, scratch resistant, baked-on powder coat finish wipes clean for long-lasting beauty for any shop or work area. Installation is easy and absolutely no framework is required.
- 32" tall x 32" wide x 3/4" deep
- Pack of two
- Durable and versatile
- 20 gauge steel with a baked-on rust and scratch resistant finish
- Slotted to accept Wall Control accessories
- Holes accept conventional 1/4" peg hooks
- Choose from blue, grey, red, white, or galvanized steel
Hurricane Aluminum Fan Shroud Kit for 22 Inch Radiator, Engine Driven Fanx
These universal fit aluminum fan shroud kits can be built to fit many applications with a belt-driven fan. The adjustable collar will accommodate 15"-20" fan diameters.
Measures 19" tall x 16-3/4" wide x 2-5/8" deep. Works well with Speedway & Afco 24" wide radiators and will work with the Speedway & Afco 22" wide radiators with slight trimming of the width of the shroud.
- Made for exact fit of many Muscle Car and Hotrod radiators
- Allows the installer the choice of off center, side-to-side and above the radiator fan positioning
- For crossflow or downflow radiator mounting
- Includes fully-formed shroud of .063" lightweight aircraft aluminum
- 3" trimmable collar
- Adjustable collar; adjusts for 15-20" fan diameters
- Includes all the necessary hardware and mounting instructions
- Measures 19" tall x 16-3/4" wide x 2-5/8" deep
Learn more about the importance of using a fan and shroud with our radiators by reading our tech article. Radiator Cooling Performance.
$17.99More InfoSweet Mfg. 001-21040 Rack and Pinion Replacement Bootx
These high quality rubber replacement boots for Sweet Mfg. rack and pinions perform as good as they look.
- Replacement for Sweet Mfg. rack and pinion
- High quality rubber construction
$69.99More InfoSpeedway Electric Speedometer, 3-3/8 Inch Diameterx
These electric speedometers are perfect for your rod or race project. They feature a white face with bold black lettering and a bright orange needle for quick monitoring. Our 0-160 mph speedometers also come with a stainless steel bezel and a complete installation kit.
- 3-3/8” body diameter
- 3-3/4 ” bezel
- Overall Diameter: 3-3/4"
- Body Length: 1.60"
- Stud Length: 1.00"
- Backlit white face with black lettering
- Orange needle
- 0-160 mph range
- Stainless steel bezel
- Includes installation kit
- SENDER NOT Included
$14.99$19.99More InfoDura-Bond FKC-1HP Small Block Chevy Engine Finishing Hardwarex
- (4) Head Dowels
- (2) Timing Cover Dowles
- (3) Cam Bolts
- (1) Cam Lock Plate
- (2) Oil Filter Adaptor Bolts
- (1) Long Woodruff Key
- (2) Short Woodruff Keys
- (2) Transmission Dowels
$307.99More InfoHooker Headers 8501HKR LS Cast Iron Exhaust Manifoldsx
Please view the product's page for more information
$3.99$5.99More InfoTitan Tools 32980 5LB Telescoping Magnetic Pick Up Toolx
These 5lb magnetic pick up tools will telescope from 6-1/2" to 33" and are ideal for retrieving dropped parts, fasteners, and tools. They feature a 3/4" diameter head with a comfortable textured cushion grip.
- 5lb telescoping magnetic pick up tool
- 5lb magnet with shielded sides for targeted pick-ups
- 3/4" Diameter head
- Telescopes from 6-1/2 to 33"Ideal for retrieving dropped parts, fasteners and tools.
- Comfortable textured cushion grip
$999.99More InfoLongacre Accuset II Scale Kitx
- Push one button for all 4 wheel weights plus cross weight
- Push a second button for all partial %
- Baseline memory recall
- Heavy duty red HiFlex cables with billet AN connectors
- 4 LMF™ swirl finished 15" x 15" low profile pads
- 1500 lb. per pad capacity, 6000 lb. total
- 2-year limited warranty
- Includes FREE scale pad box
- Push one button for all 4 wheel weights plus cross weight
$49.99$62.95More InfoLokar BAG-6085 73-98 Chevy Truck Billet Aluminum Throttle Pad w/Rubberx
These direct replacement throttle pads for 1973 - 1998 Chevy Truck feature rubber inserts and measure 2"x5". These billet aluminum pads are available in a brushed finish.
- Mounts onto factory arm and spring
- Quick and Easy Installation
- Available in brushed finish