Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 50

Products

Suspension

Shop Classic Truck Suspension At Speedway Motors

Speedway Motors is your number one source for Classic Truck suspension components! Speedway stocks a huge inventory of suspension parts, plus shocks from AFCO and Bilsein, truck springs, rear lowering springs and other specialized components you need to finish any classic pickup suspension project. You can improve the ride of your classic truck with Speedway’s selection of control arms, coilover springs, heim rod ends or complete suspension kits. We also offer the best in air ride setups and coilover kits too!

Featured Products
  • Shock Mount Studs
    $3.99
    Product Rating: 4.81 Stars
    Shock Mount Studs
    (Part #91036096)
    x
                

    Shock mounting stud is approximately 3-5/8" in overall length. The part where the shock rides, is 5/8" O.D. and approximately 1-1/4" wide and the threads at the shock end are 7/16"-20, about 7/8" long. The threads at the bracket end are 1/2"-20, about 1-1/8" long.

    Studs sold individually.

     

  • Heidts SB-012 Sway Bar Bracket Kit for Tubular Full Lower Control Arms
    New
    Heidts SB-012 Sway Bar Bracket Kit for Tubular Full Lower Control Arms
    (Part #413012)
    x
                

    This stabilizer bar bracket kit from Heidts is for tubular full lower A-Arms. These brackets bolt onto the control arms for a quick and simple installation. These brackets will only work on strut-less style control arms designed for stock coil springs. They will not bolt onto a coil over type arm as most of those do not have a plate in the center of them to bolt anything onto them.

    • Steel Construction
    • Hardware Included
    • Sold as Kit
    • Natural Finish

    Installation Instructions (PDF)

     

  • Std Heim 5/8" RH Male
    $5.99
    $7.99
    Product Rating: 4.40 Stars
    Std Heim 5/8" RH Male
    (Part #1750106)
    x
                

    These right hand standard rod ends are a general purpose, two-piece design. They have a carbon steel body and a hardened steel ball without a race (metal to metal contact).

    Applications: Clutch, brake, steering linkage, & suspension components on moderate horsepower applications.

    Assembly: To ease assembly, be sure to run a tap or die through the threads on chrome plated fasteners and apply an anti-seize compound to prevent galling of the threads.

  • Lower Coil Spring Mount Perch
    Lower Coil Spring Mount Perch
    (Part #91720243)
    x
                Lower coil spring mount welds to 3" axle tube for mounting conventional 5" coil springs.
            
  • Heidts Mustang II Swaybar End Link Mount for Tubular Lower Control Arms
    Heidts Mustang II Swaybar End Link Mount for Tubular Lower Control Arms
    (Part #413230)
    x
                

    These weld-on Mustang II front swaybar end link mounts from Heidts are for tubular lower control arms. You can chose from left or right.

    • Steel Construction
    • Natural Finish
    • Sold Individually
  • Speedway Aluminum Extruded Leaf Spring Lowering Blocks
    Speedway Aluminum Extruded Leaf Spring Lowering Blocks
    (Part #91643)
    x
                

    Our lightweight extruded aluminum lowering blocks are stronger than billet!  Available in several heights, all 2-1/2" wide, 5" long.  The centering pin is 9/16".  These blocks will increase or decrease suspension height on most leaf spring applications and can be installed below the leaf spring to raise the vehicle or on top of the leaf spring to lower the vehicle. These lowering blocks allow you to lower your leaf spring vehicle by up to 4 inches.  Heavy Duty U-bolts and hardware are available separately.

    • Lightweight aluminum lowering blocks are stronger than billet
    • 2-1/2" wide
    • 5" long
    • 9/16" centering pin
    • Increase or decrease suspension height on most leaf spring applications
    • Allows you to lower your leaf spring vehicle by up to 4 inches
    • U-bolts and hardware available separately

    Lowering blocks are sold individually (each).

    THICKNESS options explained:

    • 025 = 1/4" thick
    • 050 = 1/2" thick
    • 075 = 3/4" thick
    • 100 = 1" thick
    • 150 = 1.5" thick
    • 200 = 2" thick
    • 250 = 2.5" thick
    • 300 = 3" thick
    • 350 = 3.5" thick
    • 400 = 4" thick
  • Eagle Motorsports Chassis Repair Tool
    Eagle Motorsports Chassis Repair Tool
    (Part #96000420)
    x
                

    Eagle Motorsports factory-built component. This torsion mandrel tool is perfect for straightening bent tubes and spuds.

    • Works for 1-1/8" torsion bar tube size
    • Use for quick fixes at the track
    • Able to straighten spuds or tubes
    • Precision tuned high strenght steel

     

  • Pinto-Mustang II Spindle Nut & Washer Kit
    Pinto-Mustang II Spindle Nut & Washer Kit
    (Part #910615074)
    x
                Complete kit for 2 spindles; nuts, washers, cotter pins.  For 1974-80 Pinto, Bobcat and Mustang II. Thread size of nut: 13/16"-20
            

Filter

"Classic Truck, Suspension" Page 1 of 50

Page 1 of 50

  • S-10 2 Inch Front/ 3 Inch Rear Drop Lowering Kit
    S-10 2 Inch Front/ 3 Inch Rear Drop Lowering Kit
    (Part #9172150)
    x
                These are lowering kits that will lower your '82-'04 two wheel drive S-10 chassis just a little bit or put it in the weeds. Kits do not include shocks (sold separately). Inches of drop are an approximate and vary with car and engine weight. 
            
  • AFCO 3840C 4 Inch Double Adjustable Coilover Shock w/o Spring
    AFCO 3840C 4 Inch Double Adjustable Coilover Shock w/o Spring
    (Part #1063840C)
    x
                Please view the product's page for more information
            
  • Mustang II IFS, Narrow Control Arms, Coilover Springs, Stock Spindles
    Mustang II IFS, Narrow Control Arms, Coilover Springs, Stock Spindles
    (Part #91034208)
    x
                Please view the product's page for more information
            
  • AFCO 23600CR 10 Inch Extreme Chrome Coil-Over Spring, 600 Rate
    AFCO 23600CR 10 Inch Extreme Chrome Coil-Over Spring, 600 Rate
    (Part #10623600CR)
    x
                

    Whether you are building a purpose-built drag strip machine or a beautiful show car, Extreme Chrome coilover springs will provide the strength, durability and show stopping good looks you desire. 

    • Industry exclusive 360° polished wire
    • High quality REAL chrome finish
    • Looks great from any angle - not just on the outside edge
    • 2-5/8" inside diameter

    All Afcoils carry a lifetime warranty to remain within 2% of the original nominal free height. 

    Afcoil Spring Rate Guide (Link)

    Coil-Over Mounting Guide (Link)

  • Leaf Spring Liner with Lip, 2-1/4 Inch
    Leaf Spring Liner with Lip, 2-1/4 Inch
    (Part #91033038)
    x
                Equal partners in a smooth-riding leaf spring suspension are quality shocks and friction-free movement of the spring leafs. This special compound of poly-vinyl plastic has a very "slippery" surface which works as a permanent dry lubricant to eliminate interleaf friction and squeaking. It also features a small lip to keep it in place. 

    One 20 ft. roll does one cross spring. Liner is less than 1/16" thick.

  • AFCO 6845F Reactor Front Drag Shocks - Chevrolet/GM/Dodge
    AFCO 6845F Reactor Front Drag Shocks - Chevrolet/GM/Dodge
    (Part #1066845F)
    x
                

    AFCO Single Adjustable Monotube FRONT shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Plus, with AFCO's exclusive "BNC" valving, these shocks eliminate bounce caused by the impact after a wheel stand.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • BNC Valving eliminates front end bounce
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered

    Fits most '55-'96 GM chassis

    Fits 1979-1992 Dodge Ram half-ton 2WD pickup trucks.

    See Applications tab for fittment.

  • Speedway Steel 5/8 Inch LH Male Heim Joint Rod Ends with Stud
    Speedway Steel 5/8 Inch LH Male Heim Joint Rod Ends with Stud
    (Part #1750329)
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of.  They are teflon lined.
            
  • Seals-It WS7500 Heim Joint Rod End Seals, 3/4 Inch Hole, Set/6
    Seals-It WS7500 Heim Joint Rod End Seals, 3/4 Inch Hole, Set/6
    (Part #91001505)
    x
                

    These rod end seals are a neoprene rubber seal bonded to an aircraft quality washer. Extends the life of your rod ends by keeping the dirt, debris and moisture out of the spherical ball. They fit on both sides of the ball end of the heim joint and are sized to match the hole in the spherical ball.  

    For use with standard and Pro 1 Series rod end only. Sold in sets of six, which will cover both sides of three rod ends.

  • Carrera BKR 11-95 Front Coilover Shock Kit 450 Rate, 10.3 Inch Mounted
    Carrera BKR 11-95 Front Coilover Shock Kit 450 Rate, 10.3 Inch Mounted
    (Part #2553235F)
    x
                Please view the product's page for more information
            
  • AFCO 5/8 Inch Shock Bearing
    $10.99
    AFCO 5/8 Inch Shock Bearing
    (Part #1080TX)
    x
                Mid-to-heavyweight cars can destroy a rubber mount bushing in no time.   Instead, use spherical bearings which don't compress and allow operation   at far greater mounting angles. Works with AFCO 5/8" bearing end   shocks (except K-Series).                               
    • 5/8" I.D.
    • 1/2" wide
    • Bearing only
  • Speedway Steel 5/16 Inch LH Male Heim Joint Rod Ends with Stud
    Speedway Steel 5/16 Inch LH Male Heim Joint Rod Ends with Stud
    (Part #1750322)
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of.  They are teflon lined.
            
  • 3/8 X 3/8 Clevis
    $7.99
    3/8 X 3/8 Clevis
    (Part #6680116)
    x
                The correct clevis for mounting our rack and pinion units (668-0105 & 668-0115). 
            
  • AFCO 20136B Coil-Over Mount Bushing
    AFCO 20136B Coil-Over Mount Bushing
    (Part #10620136B)
    x
                Coil-over mount bushing.
            
  • AFCO Non-Adjustable Alum. Coil-Over Shock Kit, 7 Inch Stroke, 13 Inch Comp.
    AFCO Non-Adjustable Alum. Coil-Over Shock Kit, 7 Inch Stroke, 13 Inch Comp.
    (Part #1061370)
    x
                

    AFCO has been building racing shocks for over 20 years and are now applying their technology to street rod shocks. These aluminum coilover shock kits have superior FIXED valving that will give you a better ride and improve handling.

    • Each shock is hand built and dyno tested
    • Supplied with two 5/8" I.D. polyurethane bushings
    • Includes AFCO Mirror Finish coilover springs in the rate of your choice
    • Kit includes (2) shocks, (2) springs, and (2) coil-over hardware kits
  • Spindle Nuts for Mustang II Spindle
    Spindle Nuts for Mustang II Spindle
    (Part #91631936)
    x
                

    These spindle nuts are for your Mustang II Spindle. They are a combination of a castle nut and a washer.

    • Includes Cotter Pin
    • Sold as Pair
    • Combination of castle nut and washer
  • AFCO 3240C Pro Touring Elite Series Shock, 4 Inch Stroke
    AFCO 3240C Pro Touring Elite Series Shock, 4 Inch Stroke
    (Part #1063240C)
    x
                

    AFCO's Pro Touring Elite Series double adjustable shocks offer a unique blend of hydraulic and gas-assisted dampening that provides unparalleled on-and-off track performance. These shocks will revolutionize the handling of your dual-purpose street/autocross vehicle. 

    • Remote mounted canister allows for convenient dampening adjustment
    • Double Adjustability - broad range of adjustment
    • 1/2" I.D. x 1" wide Teflon lined spherical bearing end mounts

    Suggested Spring Height

    • 4" Stroke:  7-8"
    • 5" Stroke:  10-12"
    • 7" Stroke:  12-14"

    Coil-over compatible with purchase of additional parts.

    Front Coil-Over Mounting Guide (GIF)

    Rear Coil-Over Mounting Guide (GIF)

     

  • QA1 COM8T-102PK 1 Inch Bearing Kit
    QA1 COM8T-102PK 1 Inch Bearing Kit
    (Part #2558102)
    x
                Kit Includes:     
    • (2) Steel Spherical Bearings
      • 0.5" I.D.
      • 1.0" O.D.
      • 1.0" Wide
    • (4) Snap Rings
  • 1965-72 Chevy Pickup Rear Lowering Kit
    1965-72 Chevy Pickup Rear Lowering Kit
    (Part #91006575)
    x
                

    This kit does it all! It lowers your truck 5", Corrects the shock angle so shocks work correctly, AND centers the rear axle. (All this is recommended when lowering 5" or more.) Includes 5" drop springs and shocks, deluxe trac bar, hardware and shock relocation kit.

    Note: C-notch required. Coils come black powder coated. 

  • Gasser Straight Axle, Ford Spindle and Brake Kits, 54-1/4 Hub-to-Hub
    Gasser Straight Axle, Ford Spindle and Brake Kits, 54-1/4 Hub-to-Hub
    (Part #9103546)
    x
                

    These kits include our gasser straight front axle, semi-elliptical springs, spindles, king pins, steering arms, tierod kit, brake kit, and hardware. Choose either 5 on 4-1/2" or 5 on 4-3/4" bolt pattern with standard brake kit or Wilwood brake kit. Standard brake kits use new rotors and GM metric style calipers. Brake lines not included. Shocks not included, but shock mounts are included. Assembly required.

    Gasser Info (PDF)

    Note: Wilwood brakes increase hub-to-hub width by 1/2".

    910-3546 Instructions (PDF)

  • AFCO 23500CR 10 Inch Extreme Chrome Coil-Over Spring, 500 Rate
    AFCO 23500CR 10 Inch Extreme Chrome Coil-Over Spring, 500 Rate
    (Part #10623500CR)
    x
                

    Whether you are building a purpose-built drag strip machine or a beautiful show car, Extreme Chrome coilover springs will provide the strength, durability and show stopping good looks you desire. 

    • Industry exclusive 360° polished wire
    • High quality REAL chrome finish
    • Looks great from any angle - not just on the outside edge
    • 2-5/8" inside diameter

    All Afcoils carry a lifetime warranty to remain within 2% of the original nominal free height. 

    Afcoil Spring Rate Guide (Link)

    Coil-Over Mounting Guide (Link)

Goto Previous PagePrevious Page
1 2 3 4 5 ... 50