Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 5

Products

HVAC

Shop Classic Truck Heating & A/C At Speedway Motors

Speedway Motors has the heating and air conditioner parts you need to make your classic truck comfortable again. We offer great prices on new heater cores, control modules and air conditioning kits. Don't forget replacement air conditioning o-rings, pipes, and fittings to fix any problems your truck may have right here at Speedway Motors.

Featured Products
  • LS EVAP Delete Plug
    $12.99
    $18.99
    LS EVAP Delete Plug
    (Part #91680916)
    x
                

    These EGR EVAP delete plugs are intended for use on non-pollution controlled, off-road vehicles only.

    • For GM LS engines
    • Hardware and O-ring are included

     

  • A/C Drier with Safety Switch
    $54.99
    Product Rating: 5.00 Stars
    A/C Drier with Safety Switch
    (Part #42891003)
    x
                

    If you need to replace your drier, we have you covered. The binary switch is supplied, but it is not installed. Measures 2-3/8” x 6-1/2”.

    Note: Always mount in a cool place. Inside the car is acceptable. Mount in the vertical position with the connections on top. When properly charged, the sight glass in a 134a system will still show milky. It is recommended to replace the drier anytime a connection in the system has been opened. 

  • 90 Degree Nickel Plated AC Fitting, -6 AN
    90 Degree Nickel Plated AC Fitting, -6 AN
    (Part #6171732)
    x
                These handsome nickle plated steel fittings are reuseable.
            
  • Air Conditioning Condenser, 12 x 19-1/2 Inch
    Air Conditioning Condenser, 12 x 19-1/2 Inch
    (Part #42815215)
    x
                

    Horizontal mount aluminum A/C condenser with parallel flow. This is 12" wide by 19-5/8" tall with fittings on passenger/right hand side. Top fitting is 90 degree pointed down and lower fitting is straight point out horizontal.

    Has one -6 AN and one -8 AN fitting.

  • A/C Hose Kit
    $89.99
    Product Rating: 5.00 Stars
    A/C Hose Kit
    (Part #42810100)
    x
                

    These air conditioning hose kits include enough hose and fittings to allow a normal installation in applications without bulkhead fittings. 

    • (2) Band Clamps
    • (4) AN6 Straight
    • (1) AN8 Straight
    • (1) AN10 Straight
    • (2) AN6 90 Degree
    • (1) AN8 90 Degree
    • (1) AN10 90 Degree
    • (1) AN8 90 Degree with Service Port
    • (1) AN10 90 Degree with Service Port
    • (4) #6 O-Rings
    • (2) #8 O-Rings
    • (2) #10 O-Rings
    • (2) Grommets
    • 6 ft #6 Hose
    • 5 ft #8 Hose
    • 4 ft #10 Hose

     

    Fittings will need to be crimped at your local shop.

  • Slim Line Heat/Air Unit
    $359.99
    Product Rating: 5.00 Stars
    Slim Line Heat/Air Unit
    (Part #91000466)
    x
                This low profile under the dash mount heat/cool unit is 26.25" wide 5.25" tall and 12" deep. Features a three speed blower, heat/cool adjustment, defroster duct hook-ups, and three 1" x 5" front adjusting vents. Easy to install with mounting slots on the sides of the unit all plumbing and wiring done from the back side of the unit. Will handle 18,000 BTU's based on a Sanden or Sankyo 508 compressor at 60 MPH. The blower motor is capable of 240 CFM. Minimum condenser dimensions would be 12"X18" but would prefer a 14"X20" sized condenser, or 280 sq. in.
            
  • Flex-A-Lite 640 Mojave Universal Heater
    Flex-A-Lite 640 Mojave Universal Heater
    (Part #359640)
    x
                

    This 12,000 BTU universal heater is fully self contained, but compact in size. The 3 speed fan blows air through a heater core that is plumbed just like any newer car. Works well in most under-dash applications. Includes universal switch, fuse and wiring.

    Also available is a universal plenum which also has provisions for defroster hookups.

    359-640 Instructions (PDF)

  • 90 Degree Crimp-On O-Ring Heater Hose Fitting, -10 AN
    90 Degree Crimp-On O-Ring Heater Hose Fitting, -10 AN
    (Part #4281327)
    x
                

    These premium -10 size (7/8" x 14 TPI) crimp-on hose fittings feature O-ring seals and a 90 degree bend. Ideal for use with heater bulkhead plates.

    Note: Will need to be crimped by your local shop. 

Filter

"Classic Truck, HVAC" Page 1 of 5

Page 1 of 5

  • Aeroquip FCF0809 Stainless Steel Braided AC Hose, -8 AN, 9 Ft. Length
    Aeroquip FCF0809 Stainless Steel Braided AC Hose, -8 AN, 9 Ft. Length
    (Part #617809)
    x
                This is a superior hose for air conditioning applications. The attractive hose has a stainless steel outer braid with a nylon inner tube for excellent refrigerant performance.
            
  • 90 Degree Crimp-On O-Ring Heater Hose Fitting, -10 AN
    90 Degree Crimp-On O-Ring Heater Hose Fitting, -10 AN
    (Part #4281327)
    x
                

    These premium -10 size (7/8" x 14 TPI) crimp-on hose fittings feature O-ring seals and a 90 degree bend. Ideal for use with heater bulkhead plates.

    Note: Will need to be crimped by your local shop. 

  • Under Dash AC Unit
    $229.99
    $279.99
    Under Dash AC Unit
    (Part #91000535)
    x
                

    Looking for a simple under-the-dash A/C cooling unit? This compact air conditioning control box is just 16" long 4.25" tall and 11" deep. This unit features two large 2" X 6" air vents in front with a three-speed blower motor and cooling control adjustment.

    Note:  This unit consists of the AC evaporator, duct assembly and blower motor for the under dash use.  It will require the additional items of the compressor, hose kit, dryer and condenser to complete the A/C system.

  • Heater Core for 1967-72 GM C/K Series Truck and Blazer
    Heater Core for 1967-72 GM C/K Series Truck and Blazer
    (Part #910399067)
    x
                For your 1967-72 GM C/K Series Truck, use a 100% new heater core,    not a marginal   recore like others sell. All heater cores are a    direct fit  factory replacement for applications without A/C. 
    • All new construction
    • Direct fit factory replacement for 1967-72 GM C/K Series truck, Blazer, and Jimmy
    • Please note: non air applications

    Note: These heater cores may be shipped either aluminum or copper/brass, depending on application & inventory/stock. 

  • Air Conditioning Kit w/ Condenser
    Air Conditioning Kit w/ Condenser
    (Part #428200)
    x
                

    The days of riding around trying to look cool while sweating your butt off are gone! So is going to the junkyard and trying to find used parts to cobble up an a/c system. These kits have three dash vents and two defrost ducts and are engineered for 1930's coupes, pick-ups and smaller cars.

    These are designed with both the a/c evaporator and heater core in one unit which helps keep size and installation time down. They fit under the dash just like a new car and allow disassembly without removing the unit from the car.

    They include dash louvers, defrost louvers, switch panel, a/c hose kit, dryer with switch, Sanden 508 compressor  with V-belt pulley, and evaporator/heater assembly. They are available with or without condenser and standard finish or deluxe polished aluminum compressor.

    Hoses will need to be crimped by your local shop. R134a Freon required, but not supplied. Compressor brackets and heater hoses sold separately.

    Instructions (PDF) 

  • Heater Core for 1966-72 Ford F-Series and Bronco
    Heater Core for 1966-72 Ford F-Series and Bronco
    (Part #910399024)
    x
                For your 1966-72 Ford F-Series pickup, use a 100% new heater core,   not a marginal   recore like others sell. All heater cores are a   direct fit  factory replacement for applications without A/C. 
    • All new construction
    • Direct fit factory replacement for 1966-72 Ford F-Series and Bronco
    • Please note: non air applications

    Note: These heater cores may be shipped either aluminum or copper/brass, depending on application & inventory/stock. 

  • Aeroquip FCF1003 Stainless Steel Braided AC Hose, -10 AN, 3 Ft. Length
    Aeroquip FCF1003 Stainless Steel Braided AC Hose, -10 AN, 3 Ft. Length
    (Part #617103)
    x
                This is a superior hose for air conditioning applications. The attractive hose has a stainless steel outer braid with a nylon inner tube for excellent refrigerant performance.
            
  • Straight Nickel Plated AC Fitting w/Port, -6 AN to -6 AN
    Straight Nickel Plated AC Fitting w/Port, -6 AN to -6 AN
    (Part #6171912)
    x
                These handsome nickel plated steel fittings are reuseable. This AN6 straight fitting features a high side R134a port.
            
  • Flex-A-Lite 650 Standard Plenum for Mojave Universal Heater
    Flex-A-Lite 650 Standard Plenum for Mojave Universal Heater
    (Part #359650)
    x
                

    This plenum is made of black molded plastic and snaps onto the outlet 'grille' of the mojave heater. It has a nipple to attach one, 2.5" flex hose (like dryer vent hose - not included) to the side of the plenum.

    The plenum also has two round vents that can be rotated and which have two vanes that can be positioned to direct the airflow almost any direction or even closed to force air into the defrost hose.

    • 4-3/4" tall
    • 8-1/2" wide
    • 4-1/2" deep

    When installed on the heater, the overall dimensions of the assembly (heater with plenum) are:

    • 5" tall
    • 10" wide
    • 13" deep

    When the plenum is snapped onto the heater, the total depth (front to back) is approximately 13".

     

  • Air Conditioning Condenser, 12 x 19-1/2 Inch
    Air Conditioning Condenser, 12 x 19-1/2 Inch
    (Part #42815215)
    x
                

    Horizontal mount aluminum A/C condenser with parallel flow. This is 12" wide by 19-5/8" tall with fittings on passenger/right hand side. Top fitting is 90 degree pointed down and lower fitting is straight point out horizontal.

    Has one -6 AN and one -8 AN fitting.

  • 135 Degree Nickel Plated AC Fitting, O-Ring Pilot w/Port, -10 AN
    135 Degree Nickel Plated AC Fitting, O-Ring Pilot w/Port, -10 AN
    (Part #6171894)
    x
                These handsome nickel plated steel fittings are reuseable. This 135 degree AN10 fitting features a low side R134a port.
            
  • Crimp-On A/C O-Ring Fitting, 90 Degree, -6 AN
    Crimp-On A/C O-Ring Fitting, 90 Degree, -6 AN
    (Part #4282321)
    x
                90° elbow A/C O-ring crimp fitting with in a -6 (5/8" x 18 TPI) size.
            
  • Aeroquip FCF1009 Stainless Steel Braided AC Hose, -10 AN, 9 Ft. Length
    Aeroquip FCF1009 Stainless Steel Braided AC Hose, -10 AN, 9 Ft. Length
    (Part #617109)
    x
                This is a superior hose for air conditioning applications. The attractive hose has a stainless steel outer braid with a nylon inner tube for excellent refrigerant performance.
            
  • 90 Degree Nickel Plated AC Fitting, O-Ring Pilot w/ Port, -10 AN
    90 Degree Nickel Plated AC Fitting, O-Ring Pilot w/ Port, -10 AN
    (Part #6171834)
    x
                These handsome nickel plated steel fittings are reuseable. This 90 degree AN10 fitting features a low side R134a port.
            
  • Air Conditioning Kit w/o Condenser
    Air Conditioning Kit w/o Condenser
    (Part #428100)
    x
                

    The days of riding around trying to look cool while sweating your butt off are gone! So is going to the junkyard and trying to find used parts to cobble up an a/c system. These kits have three dash vents and two defrost ducts and are engineered for 1930's coupes, pickups and smaller cars.

    These are designed with both the a/c evaporator and heater core in one unit which helps keep size and installation time down. They fit under the dash just like a new car and allow disassembly without removing the unit from the car.

    They include dash louvers, defrost louvers, switch panel, a/c hose kit, dryer with switch, compressor with V-belt pulley, and evaporator/heater assembly. They are available with or without condenser and standard finish or deluxe polished aluminum compressor.

    Hoses will need to be crimped by your local shop. R134a Freon required, but not supplied. Compressor brackets and heater hoses sold separately.

    428-100 Instructions (PDF)

  • 90 Degree Nickel Plated AC Fitting, -6 AN
    90 Degree Nickel Plated AC Fitting, -6 AN
    (Part #6171732)
    x
                These handsome nickle plated steel fittings are reuseable.
            
Goto Previous PagePrevious Page
1 2 3 4 5