Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 10

Products

Fuel Injection

Shop Classic Truck Air & Fuel Delivery At Speedway Motors

Speedway Motors stocks all the best names in classic truck carburetors and intake manifolds! Plus, we have a great selection of fuel cells and gas pedals, as well as electric and mechanical fuel pumps. Don't forget to let your engine breath with filters from K&N and R2C. Speedway can fuel your need for speed!

Featured Products
  • Hilborn Flathead Ford Mechanical Fuel Injection
    Hilborn Flathead Ford Mechanical Fuel Injection
    (Part #385239F8A)
    x
                

    This Hilborn Mechanical Fuel Injection unit fits the Ford Flathead 239 V8 engine. It comes complete with #6 nozzles and 9" stacks. For use with gasoline. Recommended fuel pump is 150C #0 direct from Hilborn. Fabrication required to drive the fuel pump and for linkage.

    • High quality heat-treated aluminum casting
    • Cad-plated steel ram tubes
    • Fully assembled with shafts, butterflies, nozzles, fuel lines, metering valve, & bypass valve
  • Fragola 4919461-BL O-Ring Boss Carb Adapter, -8 AN to -8 AN, Short
    New
    Fragola 4919461-BL O-Ring Boss Carb Adapter, -8 AN to -8 AN, Short
    (Part #6174919461)
    x
                
    Fragola Performance is proud to offer this made in the USA, O-ring Boss carburetor adapter. This is just one of the many top quality fluid delivery products offered by Fragola.
    • -8 AN Male to 3/4"-16 (-8AN) port fitting
    • Fuel line adapter fitting
    • Black anodized finish
    • Made in the USA
  • AIRAID 120-400 Air Tube Coupler with Clamps, 4 Inch Diameter
    AIRAID 120-400 Air Tube Coupler with Clamps, 4 Inch Diameter
    (Part #178120400)
    x
                These silicon hose connectors are great for use with  AirAid's   performance air intake systems. They come complete with clamps and are  designed to be used with 4"   diameter air tubing.
    • Works with 4" tubing (178100400)
    • Durable silicon material
    • Stainless steel clamps included
  • MSD 23131 MAP Sensor
    $88.99
    $93.99
    MSD 23131 MAP Sensor
    (Part #54723131)
    x
                The pressure inside the intake manifold is an extremely important input to the ECU. This sensor will respond to changes in manifold pressures and relay the information to the ECU in the form of a voltage signal ranging from about 1 volt to 5 volts. Several different versions are available for normally-aspirated and engines with blowers.
    • Applications up to 30lbs of boost
  • LS1/LT1 EFI Fuel Line Fitting, -6 AN Male to 3/8 Inch Female, Black
    LS1/LT1 EFI Fuel Line Fitting, -6 AN Male to 3/8 Inch Female, Black
    (Part #61744123)
    x
                
    • Direct replacement for OEM fuel rail and return line fittings in late-model EFI pressure side application
    • Exclusive SAE quick disconnect threaded aluminum retaining cap for ease of installation and positive engagement under high pressure
    • 37° sealing angle provides a positive seal at maximum operating pressures
    • Black anodized finish
  • Aluminum Fuel Line, 3/8 Inch O.D.
    From: $10.99
    Product Rating: 4.78 Stars
    Aluminum Fuel Line, 3/8 Inch O.D.
    (Part #91011430)
    x
                Where else can you buy aluminum fuel line in the size and length you need? This easy-to-flare and bend tubing will save weight and money. 
    • Use with tube nut couplers, sleeves and 37° flared AN fittings
    • Rated to 250 psi
    • Not recommended for high pressure (brake) applications
    • Available in 10 ft., 20 ft., or 30 ft. coils

    Learn more about flaring lines and how to select proper automotive fittings by reading our tech article. The Principles of Automotive Fittings.

  • Russell Performance 641605 LS/Hemi EFI Fuel System Retrofit Kit
    Russell Performance 641605 LS/Hemi EFI Fuel System Retrofit Kit
    (Part #325641605)
    x
                

    This fuel pump kit provides a complete electronic fuel system for GM LS-series and Chrysler 5.7 Hemi engine swaps in muscle cars, street rods and off-road vehicles. Kit features an Edelbrock EFI fuel pump, regulator/filter, relay, Russell Pro Flex hose, an assortment of silver and black AN hose end fittings, and all mounting hardware. When using with OEM fuel tank sending units, an additional adapter to -6 male AN is required.

    • For GM/Chevy LS and Chrysler 5.7 Hemi engine swaps into older non-EFI vehicles
    • Includes Edelbrock Electric Fuel Pump # 3594
    • Includes Edelbrock Fuel Pressure Regulator
    • Returnless Fuel System
    • Supports up to 450 HP
  • Lokar TCB-40TP2 GM TPI Throttle Cable Bracket
    Lokar TCB-40TP2 GM TPI Throttle Cable Bracket
    (Part #49140TP2)
    x
                Use this bracket to attach the hi-tech throttle and kickdown cable to your GM Tuned Port Injection unit.
            

Filter

"Classic Truck, Fuel Injection" Page 1 of 10

Page 1 of 10

  • Lokar TCB-40TP3 Tuned-Port Billet Aluminum Bracket w/Triple Stud
    Lokar TCB-40TP3 Tuned-Port Billet Aluminum Bracket w/Triple Stud
    (Part #491TCB40TP3)
    x
                

    The billet aluminum bracket mounts to the side of the Tuned-Port plenum. The billet aluminum bracket is available with:

    • a single stud for throttle only
    • double stud for throttle and kickdown
    • triple stud for a throttle, kickdown and cruise control cable.
  • Russell Performance 641605 LS/Hemi EFI Fuel System Retrofit Kit
    Russell Performance 641605 LS/Hemi EFI Fuel System Retrofit Kit
    (Part #325641605)
    x
                

    This fuel pump kit provides a complete electronic fuel system for GM LS-series and Chrysler 5.7 Hemi engine swaps in muscle cars, street rods and off-road vehicles. Kit features an Edelbrock EFI fuel pump, regulator/filter, relay, Russell Pro Flex hose, an assortment of silver and black AN hose end fittings, and all mounting hardware. When using with OEM fuel tank sending units, an additional adapter to -6 male AN is required.

    • For GM/Chevy LS and Chrysler 5.7 Hemi engine swaps into older non-EFI vehicles
    • Includes Edelbrock Electric Fuel Pump # 3594
    • Includes Edelbrock Fuel Pressure Regulator
    • Returnless Fuel System
    • Supports up to 450 HP
  • Lokar XTCB-40RJ1 Midnight Series 502 Ram Jet Throttle Cable Bracket
    Lokar XTCB-40RJ1 Midnight Series 502 Ram Jet Throttle Cable Bracket
    (Part #491XTCB40RJ1)
    x
                
    • Brackets fit the GM ramjet engine.
    • These brackets along with Lokar Throttle Cables will allow the ramjet to work properly in any vehicle.
    • When used with an automatic transmission, be sure to use the transmission specific Lokar Kickdown Cable.
    • Uses TC-1000RJ throttle cable.
  • Aluminum Flare Fitting Plug, Blue, -16 AN
    Aluminum Flare Fitting Plug, Blue, -16 AN
    (Part #6176023)
    x
                

    Aluminum flare plugs. 37° AN.

    Fitting Thread Application Chart (GIF)

  • Lokar XTCB-40TP2 Midnight Series Tuned-Port Alum Bracket w/Double Stud
    Lokar XTCB-40TP2 Midnight Series Tuned-Port Alum Bracket w/Double Stud
    (Part #491XTCB40TP2)
    x
                
    • The billet aluminum bracket mounts to the side of the Tuned-Port plenum.
    • The billet aluminum bracket is available with a double stud for throttle and kickdown
  • Lokar TCB-40TP1 Tuned-Port Billet Aluminum Bracket w/Single Stud
    Lokar TCB-40TP1 Tuned-Port Billet Aluminum Bracket w/Single Stud
    (Part #491TCB40TP1)
    x
                

    The billet aluminum bracket mounts to the side of the Tuned-Port plenum. The billet aluminum bracket is available with:

    • a single stud for throttle only
    • double stud for throttle and kickdown
    • triple stud for a throttle, kickdown and cruise control cable.
  • AFCO 10176-24 Throttle Rod, 24 Inch Long
    AFCO 10176-24 Throttle Rod, 24 Inch Long
    (Part #1061017624)
    x
                
    • 1/4" plated steel rod
    • 1/4" male right hand threads on both ends
    Note: Extra-long thread allows more adjustment
  • Edelbrock 12801 Polished 2-Carb Fuel Block
    Edelbrock 12801 Polished 2-Carb Fuel Block
    (Part #32512801)
    x
                

    Edelbrock has reintroduced the vintage cast aluminum fuel blocks for dual, triple and quad carb applications for your hot rod or custom. This fuel log features a single 3/8" NPT inlet and two 1/4" NPT outlets. Each fuel distribution block has four holes for mounting to a firewall.

    Polished finish.

  • Hex Polished Aluminum Fuel Block, 4-Hole
    Hex Polished Aluminum Fuel Block, 4-Hole
    (Part #91611034)
    x
                

    Speedway fuel blocks provide even fuel distribution for proper fuel flow to multi-carb set-ups. This 1950's style six-sided polished aluminum fuel distribution block is designed for four-carb applications. Fuel log is 5" long and has a single 1/4" NPT pipe inlet fittng. Outlets for carburetor fittings are 1/8" NPT threaded ports.

    Don't forget to order the suggested hose barb fittings to complete your set-up!

  • -6 AN Carb and Fuel Pump Fitting, 5/8 Inch-18 Inverted Flare Thread
    -6 AN Carb and Fuel Pump Fitting, 5/8 Inch-18 Inverted Flare Thread
    (Part #6174038)
    x
                

    Fits the Rochester 2GC Carburetor Part Number 455-37001.

    Fitting Thread Application Chart (GIF)

  • Trans-Dapt 2566 Torque Curve MPFI Spacer - GM
    Trans-Dapt 2566 Torque Curve MPFI Spacer - GM
    (Part #7202566)
    x
                

    This spacer was designed to give you an increase in fuel mileage, torque and throttle response but with ease of installation and a great price. Most others cause unwanted turbulence and create an annoying whistle. Includes hardware and gaskets.

    1999-2006 Chevy/GMC 1500, 2500, 3500 trucks, SUVs, Tahoe, Suburban, Yukon, Escalade, Hummer H2 and Motorhomes with 4.8,5.3, 6.0 and 8.1 engines with multi-port fuel injection.

    720-2566 Instructions (PDF) 

  • Lokar XTCB-40EFI Midnight Series Ford EFI Throttle Bracket 86-93, EGR
    Lokar XTCB-40EFI Midnight Series Ford EFI Throttle Bracket 86-93, EGR
    (Part #491XTCB40EFI)
    x
                
    • Ford EFI Bracket fits 1986 to 1993, Ford 302, and 351 electronic fuel injection systems that have installed the Mustang EGR spacer.
    • This Stainless Bracket mounts in stock location for easy installation of our Kickdown Cables and Throttle Cables.
    • (1986 to 1993 uses TC-1000HT)
    • The EFI Bracket does not fit B.A.P. throttle bodies.
  • Round Polished Aluminum Fuel Block, 4-Hole
    Round Polished Aluminum Fuel Block, 4-Hole
    (Part #91611014)
    x
                

    Speedway fuel blocks provide even fuel distribution for proper fuel flow to multi-carb set-ups. This polished aluminum fuel distribution block is designed for four-carb applications. Fuel log is 1-1/4" O.D. x 5" long and has a single 1/4" NPT pipe inlet fittng. Outlets for carburetor fittings are 1/8" NPT threaded ports.

    Don't forget to order the suggested hose barb fittings to complete your set-up!

  • AIRAID 9500 L Shaped 90 Degree Tube Mount Bracket
    AIRAID 9500 L Shaped 90 Degree Tube Mount Bracket
    (Part #1789500)
    x
                

    Use these air tube mounting brackets to secure your new U-Build-It custom intake systems from AirAid. Available in multiple sizes, these brackets are versatile enough to allow adjustment to your specific tube length or size. 

    • "L" shaped 90°
    • Mounts air intake tubes 
  • Round Polished Aluminum Fuel Block, 2-Hole
    Round Polished Aluminum Fuel Block, 2-Hole
    (Part #91611012)
    x
                

    Speedway fuel blocks provide even fuel distribution for proper fuel flow to multi-carb set-ups. This polished aluminum fuel distribution block is designed for two-carb applications. Fuel log is 1-1/4" O.D. x 3" long and has a single 1/4" NPT pipe inlet fittng. Outlets for carburetor fittings are 1/8" NPT threaded ports.

    Don't forget to order the suggested hose barb fittings to complete your set-up!

  • Round Polished Aluminum Fuel Block, 3-Hole
    Round Polished Aluminum Fuel Block, 3-Hole
    (Part #91611013)
    x
                

    Speedway fuel blocks provide even fuel distribution for proper fuel flow to multi-carb set-ups. This polished aluminum fuel distribution block is designed for three-carb applications. Fuel log is 1-1/4" O.D. x 4" long and has a single 1/4" NPT pipe inlet fittng. Outlets for carburetor fittings are 1/8" NPT threaded ports.

    Don't forget to order the suggested hose barb fittings to complete your set-up!

  • AIRAID 200-100 Cold Air Intake Housing Carburetor Adapter
    AIRAID 200-100 Cold Air Intake Housing Carburetor Adapter
    (Part #178200100)
    x
                

    In addition to individual components, AIRAID® offers several specialty components. Two different carburetor hats are compatible with many EFI throttle bodies and most popular performance carburetors. These specific air intake carb hats are designed to work with 5-1/8" carburetors to improve air flow and overall horsepower.

    • Roto molded construction
    • Works with 5-1/8" carburetors
    • 3-1/2" tube inlet size

     

  • Lokar TCB-40LS1 1998-99 LS1 Throttle Cable Bracket, Single
    Lokar TCB-40LS1 1998-99 LS1 Throttle Cable Bracket, Single
    (Part #49109899)
    x
                Clean up your LS1 intake manifold with this billet aluminum cable bracket. Available with a single stud for throttle only or a double stud to add cruise control or kickdown cable. Designed to work with part #491-1000LS1.
            
  • Carb and Fuel Pump Fitting, 1/2 Inch-20, AN 6
    Carb and Fuel Pump Fitting, 1/2 Inch-20, AN 6
    (Part #6174033)
    x
                

    #6 Ford, Chrysler and early Chevy fuel pumps with 1/2"-20 inverted flare thread.

    Fitting Thread Application Chart

  • LS1/LT1 EFI Fuel Line Fitting, -6 AN Male to 5/16 Inch Female, Black
    LS1/LT1 EFI Fuel Line Fitting, -6 AN Male to 5/16 Inch Female, Black
    (Part #61744113)
    x
                
    • Direct replacements for OEM fuel rail and return line fittings in late-model EFI pressure side application
    • Features exclusive SAE quick disconnect threaded aluminum retaining cap for ease of installation and positive engagement under high pressure
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Black anodized finish
Goto Previous PagePrevious Page
1 2 3 4 5 ... 10