Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Chassis & Frame At Speedway Motors

Start your Classic Truck project right here at Speeway Motors with a wide variety of chassis & frames. Multiple frames and transmission cushions are available. Make sure your classic pickup truck project starts on the right track with reproduction frames rails right here at Speedway Motors!

"Classic Truck, Frame" Page 1 of 3

  • Universal Expanding Body Mounts
    Universal Expanding Body Mounts
    x
                

    If you are building a lightweight car like a "T" or an "A", mounting the body may present a problem. These neat expanding rubber universal body mounts allow you to drill a 3/4" hole in the top of the frame, insert a 3/8" coarse bolt, tighten, then the body is mounted.

    Not recommended for cars newer than 1934.

  • DEi 010393 Reflect-A-GOLD Heat Reflective Tape, 24 x 24 Inch Sheet
    DEi 010393 Reflect-A-GOLD Heat Reflective Tape, 24 x 24 Inch Sheet
    x
                Reflect-A-GOLD is a metalized polyamide  polymer laminated glass cloth with a high temperature pressure sensitive  adhesive for use in extreme temperature swing environments. It is  lightweight and easy to apply and remove. 

    Highly effective material for firewalls, fuel cells, engine covers, under hoods, engine compartment, bulk heads, seat bottoms – anything or area that needs protection from heat.

    • For firewalls, bulkheads, engine covers, floors, seat bottoms & more
    • Capable of handling continual temperatures up to 850°F
    • Resists UV degradation for long-term performance
    • Virtually NO clearance needed
    • Adhesive protected by a release liner rated up to 325°F
    • Light weight and flexible-Trim to size
    • Space age polymer material
    • Reflects up to 850°F! Reflecting 80% of heat!
    • Ultra light weight and self adhesive
  • Bolt-In 1947-54 Chevy Pickup Mustang II Crossmember
    Bolt-In 1947-54 Chevy Pickup Mustang II Crossmember
    x
                

    Our bolt-in Mustang II suspension kit for 1947-1954 Chevy half-ton and 3/4 ton pickups includes all hardware and instructions. 

    • Completely bolt in - no welding required
    • Based on proven Mustang II geometry
    • Complete with bolt in boxing plates to reinforce the frame
    • Interlocking design for ultimate strength
    • Threaded adjusters to fine tune ride height
    • Full lower A-arms required with this crossmember (strutless type)
    • Requires the use of a power rack and pinion and tubular control arms
    • NOT for use with air ride

    910-44754 Instructions (PDF)

    Note:  Use bolt-in motor mount kit 910-54754 to mount your S/B Chevy.
  • Rubber GM Transmission Cushion
    Rubber GM Transmission Cushion
    x
                

    OEM-style rubber transmission cushion for many '58-'82 GM transmissions including TH350 auto, Muncie, Saginaw, and others.

    • Meets or exceeds OEM specifications 
    • Rubber formulation provides abrasion resistance and aging stability
    • Tough, hardened steel plate & inserts
    • Chemlock® bonding agent ensures superior rubber-to-metal bond
  • TH350 Transmission Cushion Mount-Polyurethane
    TH350 Transmission Cushion Mount-Polyurethane
    x
                

    Heavy duty Turbo 350 polyurethane replacement for original GM mounts. Features a built-in safety lock to prevent separation. For race or street race use.

    Fits "most" GM transmissions having a mount on the tailshaft. The bolt spacing for the tranny mount will accomodate 3-3/4" to 4-1/4" bolt pattern on the transmission. For TH350 application.

  • 1940-1941 Ford Pickup Running Boards
    1940-1941 Ford Pickup Running Boards
    x
                Smoothie custom style. Fit 1/2 ton pick-up and 1/2 ton panel (not for sedan delivery). Choose left hand or right hand. Fiberglass construction. Ships UPS oversize. 

    This product is usually in stock. However, if it is not, please allow three to four weeks for delivery. 

  • 1953-56 Ford Half Ton Pickup Running Boards
    1953-56 Ford Half Ton Pickup Running Boards
    x
                Oversize UPS. Fiberglass construction. 

    This product is usually in stock. However, if it is not, please allow three to four weeks for delivery. 

  • Tubular Transmission Mount with 2 Inch Drop
    Tubular Transmission Mount with 2 Inch Drop
    x
                

    Universal rear transmission mounts and heavy duty tube crossmember. Fit most GM, Ford, and Mopar manual and auto transmissions. Black powder coated finish. Crossmember must be welded directly into frame or to 3 hole mounting flanges for bolt-in application. Fits frames up to 38" wide.

     

    Note: May require re-drilling of the mount holes when used with Ford C4/C6 trans cushion 910-18017.

  • Tubular Transmission Mount with 6 Inch Drop
    Tubular Transmission Mount with 6 Inch Drop
    x
                

    Universal rear transmission mounts and heavy duty tube crossmember. Fit most GM, Ford, and Mopar manual and auto transmissions. Black powder coated finish. Crossmember must be welded directly into frame or to 3 hole mounting flanges for bolt-in application. Fits frames up to 38" wide.

     

    Note: May require re-drilling of the mount holes when used with Ford C4/C6 trans cushion 910-18017.

  • Speedway Economy 12 Circuit Wiring Harness
    Speedway Economy 12 Circuit Wiring Harness
    x
                

    This harness was designed to offer you all the highest quality components in a package designed for cars with minimum accessories. Each wire is color coded and labeled every few inches.

    Our prewired 12 circuit kit will fit all your basic needs and makes wiring a painless process. It is designed especially for the street rod without accessories. It also includes horn relay and connector, turn and hazard signals, dimmer switch connector, circuit breaker for headlights, two flashers, one alternator plug, two ignition switch connectors, plus more.

    • Mainfuse box base is 1-7/8" x 3-11/16"
    • Box height is 3-3/4"
    12 Circuit Wiring Harness Installation Instructions (PDF)
  • DEi 010408 Cool-Tape Heat Reflective Tape, 1-3/8 Inch x 15 Ft.
    DEi 010408 Cool-Tape Heat Reflective Tape, 1-3/8 Inch x 15 Ft.
    x
                

    Cool Tape is a flexible and super strong self-adhesive thermal insulating tape capable of protecting up to 2000°F of radiant heat. Made of one mil aluminized material bonded to a woven glass fiber heat resistant matting, Cool Tape is a ultra light weight heat reflective solution for wrapping wires, cables, hoses, fuel lines, covering seams and many other uses.

    • Withstands direct heat up to 400°F and 2000°F radiant heat
    • Protects lines, hoses, cables, and more
    • Aluminized and bonded to fiberglass
    • Flexible and easy to apply
    • Strong self-adhesive backing
    • Use to secure panels, seal air boxes, wrap wiring & more

    Cool Tape Frequently Asked Questions (PDF)

  • Heidts Mustang II Crossmember for 1953-56 Ford F-100 Pickup Frame, Weld-On
    Heidts Mustang II Crossmember for 1953-56 Ford F-100 Pickup Frame, Weld-On
    x
                Please view the product's page for more information
            
  • Heatshield Armor Exhaust Wrap, 1/2 Inch Thick, 12 x 60 Inch Sheet
    Heatshield Armor Exhaust Wrap, 1/2 Inch Thick, 12 x 60 Inch Sheet
    x
                Stop heat at its source with Heatshield Armor exhaust wrap. It has an aluminum shell and inner ceramic liner that allows it to withstand continuous 1800 degree Farenheit temperatures. Best of all, it's flexible, easy to cut and simple to install using six 14" long stainless steel ties to wrap it around your pipes. Each kit contains a 1' x 5' section of material.
            
  • Thermo Tec 16000 Fire-Proof Shifter Boot
    Thermo Tec 16000 Fire-Proof Shifter Boot
    x
                

    The Fire-Proof Shifter Boot is made of woven silica with a flexible Mylar finish. The shifter boot was developed as a fire barrier for high-speed engine fires, which can burn away rubber boots in seconds. Thermo-Tec's Fire-Proof Shifter Boot gives the driver one more level of protection from engine fires and tunnel heat.  Includes boot only, mounting ring not included.

    Universal, fits many applications. 

  • Thermo Tec 13500 Adhesive-Backed Aluminized Heat Barrier, 12 x 12 Inch
    Thermo Tec 13500 Adhesive-Backed Aluminized Heat Barrier, 12 x 12 Inch
    x
                

    Protect parts and components from radiant heat. This special adhesive-backed material can be used to protect painted surfaces, plastic  parts and more. This heat barrier is composed of woven silica with a flexible aluminized finish and a strong adhesive. The reflective surface of the material is capable of withstanding   radiant temperatures of up to 2000ºF. Material can be easily applied to any surface or wrapped around hoses and wires for a clean professional appearance.

  • Thermo Tec 17062 Thermo-Flex Insulation, 5/8 Inch I.D. x 3 Ft.
    Thermo Tec 17062 Thermo-Flex Insulation, 5/8 Inch I.D. x 3 Ft.
    x
                

    Thermo-Flex heat shield is a composite material with unlimited uses. The material is manufactured to provide abrasion resistance, thermal insulation and physical containment of hoses and wiring. The combination of aluminum and silica produces a sleeving that is flexible, lightweight and strong. Thermo-Flex can be slit for applications such as wire looms or hosecovering without disconnecting the ends of the wire or hose.

    Thermo-Flex will withstand temperatures in excess of 750º F in radiant heat.

  • 1934 Ford Extended Cab Pickup Running Boards
    1934 Ford Extended Cab Pickup Running Boards
    x
                

    Heavy gauge steel construction for strength. These are a smooth, no-covering style made 6" longer-than-stock to be used in conjunction with the extended cab 1934 Ford pickup assembly. Perfect mate to our extended frame rails. 

    Ready for prep and paint.

  • Aluminized Heat and Sound Insulation Shield, 4 x 6 Foot Sheets
    Aluminized Heat and Sound Insulation Shield, 4 x 6 Foot Sheets
    x
                

    These aluminized heat shields are constructed of two layers of 99.5% pure grade industrial aluminum, laminated to 3/8" fiber tech padding to achieve highest reflection of radiant heat and sound deadening. Includes 4 feet by 6 feet of thermal and noise insulation.

    • Insulates against heat, noise and cold 
    • Mold and mildew proof
    • Fire retardent
    • Reflects 97% of infrared energy
    • Fiberglass reinforced
    • Single-sided aluminum backing
    • 4' x 6' sheet
  • Gusset Kit/Tab Kit, 60 Piece
    $49.99
    $51.99
    Product Rating: 5.00 Stars
    Gusset Kit/Tab Kit, 60 Piece
    x
                

    This Gusset Kit / Tab Kit includes:

    • (10) - Standard gussets with 1/2" hole
    • (10) - Standard 3 hole gussets
    • (10) - Chassis tab, 3/16" steel with 1/2" hole
    • (10) - Trick tab, 1/8" steel with 1/4" hole
    • (10) - Body tabs, .085" steel with 1/4" hole
    • (10) - seat belt tabs, 3/16" steel with 1/2" hole
  • Ford C4-Ford C6 Transmission Cushions
    Ford C4-Ford C6 Transmission Cushions
    x
                

    The studs on the Ford C4 or Ford C6 tranny mount are 10mm x 1.5 thread. It is a standard replacement mount that fits most Fords and is not uncommon, as metric fasteners have been used on domestic vehicles for over 25 years. For Ford C4 and Ford C6 application.

    The slots in the crossmember will require a little grinding to use this mount.

  • 1953-56 Ford Pickup Front Frame Boxing Plates
    1953-56 Ford Pickup Front Frame Boxing Plates
    x
                

    When using original or reproduction frame rails, be sure to fully box the front section for strength and saftey. Our front boxing plates are designed to box the frame in critical front suspension attachment points and motor mount areas.

    10 gauge.

  • Heidts 1947-54 Chevy Truck Econo Mustang II Crossmember
    Heidts 1947-54 Chevy Truck Econo Mustang II Crossmember
    x
                Please view the product's page for more information
            
  • Heidts Universal Multi-Fit 60 Econo Mustang II Crossmember Kit
    Heidts Universal Multi-Fit 60 Econo Mustang II Crossmember Kit
    x
                Please view the product's page for more information
            
  • DEi 010450 Titanium Exhaust Pipe Heat Shield, 6 Inch x 1 Ft.
    DEi 010450 Titanium Exhaust Pipe Heat Shield, 6 Inch x 1 Ft.
    x
                With the strategic placement of DEI’s Titanium Pipe Shield near transmissions, brake lines, floorboards, body panels, diesel exhaust stacks or motorcycle pipes, radiant heat can be controlled for maximum protection and performance.  Other uses include isolated areas such as sections of the exhaust pipe after the collector, an area that can heat transmission fluid, or along the path of an exhaust system in proximity of gas tanks, differentials and rear facias. The shield is designed for multiple automotive applications as well as marine, powersports, diesel and industrial applications where heat dissipation and thermal control is needed.
    • Capable of handling high temperature exposure up to 1350° F
    • Protects heat sensitive components, hoses, lines and electrical wiring
    • Easy to install with unique rivet-based pipe standoff brackets and pipe clamps
    • Reduces heat from entering vehicle when placed on exhaust pipes
    • Simple to re-position
    • 6" Wide x 1' Long
  • Speedway 1953-1956 Ford F-100 Truck Mustang II Crossmember
    Speedway 1953-1956 Ford F-100 Truck Mustang II Crossmember
    x
                Please view the product's page for more information
            
  • 1947-1954 Chevy 1/2 Ton Pickup Truck Frame Rails
    1947-1954 Chevy 1/2 Ton Pickup Truck Frame Rails
    x
                

    Build a firm foundation for your vintage 1947-54 Chevy 1/2 ton pickup without picking up a welder! This innovative line of chassis components from Speedway Motors allows the do-it-yourself rodder to assemble a frame using only basic hand tools and a drill.

    • Laser cut from 7-gauge steel plate
    • Replicates shape and dimensions of original Chevy frame
    • Welded on a rail fixture to ensure proper shape
    • Ground and sanded to prep for finishing
    • For '47-'54 1/2 pickups

    916-04754 Instructions (PDF)

    NOTE: Finish will be plain steel, not powder coated as shown.

  • Tubular Transmission Mount with 8 Inch Drop
    Tubular Transmission Mount with 8 Inch Drop
    x
                

    Universal rear transmission mounts and heavy duty tube crossmember. Fit most GM, Ford, and Mopar manual and auto transmissions. Black powder coated finish. Crossmember must be welded directly into frame or to 3 hole mounting flanges for bolt-in application. Fits frames up to 38" wide.

     

    Note: May require re-drilling of the mount holes when used with Ford C4/C6 trans cushion 910-18017.

  • DEi 010461 Reflect-A-Cool Heat Reflective Tape Sheet, 12 x 24 Inch
    DEi 010461 Reflect-A-Cool Heat Reflective Tape Sheet, 12 x 24 Inch
    x
                

    Reflect-A-Cool, constructed of fiberglass material backed with a layer of aluminized reflective foil to handle direct continuous temperature of 400°F has many uses such as covering firewalls, marine engine compartments, RVs, in the tub of a racecar where typical mechanical fasteners cannot be used and has many industrial uses.

    Reflect-A-Cool can be trimmed to fit just about any shape. Just measure, trim, face reflective side towards source of radiant heat and remove self-adhesive backing. It’s that easy.

    • Protect wires, cables, hoses, pipes & tubing from radiant heat sources
    • Radiant heat protection up to 2000°F
    • Self-adhesive backing with release liner for easy installation
    • Moisture & solvent resistant
    • Virtually NO clearance needed

    Reflect-A-Cool Frequently Asked Questions (PDF)

  • Thermo Tec 14002 Thermo-Shield Thermal Tape
    Thermo Tec 14002 Thermo-Shield Thermal Tape
    x
                

    Thermo-Shield protects hoses and wires from radiant heat. Thermo-Shield is used in applications where it is difficult or not practical to disconnect one end of the hose or wire. NOT FOR USE ON EXHAUST PIPE.

    The adhesive-backed composite construction tape can easily be wrapped around the hose or wire to make a clean, professional appearance and protect parts from over 90% of radiant heat up to 2000 degrees Fahrenheit.

    Comes in a 1-1/2" wide x 15' foot roll.

  • Bolt-In 1935-40 Ford Mustang II Crossmember
    Bolt-In 1935-40 Ford Mustang II Crossmember
    x
                Please view the product's page for more information
            
  • Heidts 1955-59 Chevy Truck Econo Mustang II Crossmember
    Heidts 1955-59 Chevy Truck Econo Mustang II Crossmember
    x
                Please view the product's page for more information
            
  • Straight Tubular Transmission Mount
    Straight Tubular Transmission Mount
    x
                

    Universal rear transmission mounts and heavy duty tube crossmember. Fit most GM, Ford, and Mopar manual and auto transmissions. Black powder coated finish. Crossmember must be welded directly into frame or to 3 hole mounting flanges for bolt-in application. Fits frames up to 38" wide.

     

    Note: May require re-drilling of the mount holes when used with Ford C4/C6 trans cushion 910-18017.

  • Speedway Universal 20 Circuit Wiring Harness
    Speedway Universal 20 Circuit Wiring Harness
    x
                Whether you're building an option loaded car or just want to have extra circuits available for future updates, this harness is perfect and makes any job painless. Compact 5-1/2"L x 4-1/2"W x 3-1/4"H  fuse block holds 18 standard push-in fuses and can be mounted almost anywhere. 

    Each high temperature wire is color coded and labeled every six inches. Also includes GM type steering column connectors. To keep costs down and the quality high, this harness does not include any switches, light sockets or plugs that you would normally already have.

    • Harness has 20 circuits, of which 18 are fused
    • Taillight leads measure 17' long
    • Includes plug for GM column, headlight switch, dimmer switch, and signal flashers

    Wiring Harness Installation Instructions (PDF)

  • Speedway 1955-1959 Chevy Truck Crossmember
    Speedway 1955-1959 Chevy Truck Crossmember
    x
                Please view the product's page for more information
            
  • Small Block Ford Crossmember Motor Mount
    Small Block Ford Crossmember Motor Mount
    x
                Universal mount allows 260-289-302-351W S/B Fords and 1970-1974 Cleveland engines with front sump oil pan to be installed into most frames up to 38" wide. Cut for frame width, then bolt or weld in.   

    Note: We've found a lot of variation in width of Ford blocks. Bolt the cushion to the block first to get proper width measurement. Mounts are not returnable once they've been altered or installed!

  • Speedway Mustang II Crossmember for 1947-54 Chevy Pickup Frame, Kit
    Speedway Mustang II Crossmember for 1947-54 Chevy Pickup Frame, Kit
    x
                Please view the product's page for more information
            
  • 1947-1954 Chevy Pickup Front Frame Boxing Plates
    1947-1954 Chevy Pickup Front Frame Boxing Plates
    x
                

    When using original or reproduction frame rails, be sure to fully box the front section for strength and saftey. Our front boxing plates are designed to box the frame in critical front suspension attachment points and motor mount areas.

    10 gauge.

  • Aluminized Heat Barrier, 40 x 36 Inch
    Aluminized Heat Barrier, 40 x 36 Inch
    x
                

    Protect your equipment from radiant heat. Often used to create curtains and screens, this sheeting has an aluminum foil backing that reflects heat and withstands temperatures up to 300° F. The fiberglass fabric base is off-white and has a maximum temperature of 1000° F. Foil backing is silver.

  • Heidts Universal 56-1/2 Econo Crossmember
    Heidts Universal 56-1/2 Econo Crossmember
    x
                Please view the product's page for more information
            
  • Universal Body To Frame Cushion Kit
    Universal Body To Frame Cushion Kit
    x
                Our universal body-to-frame cushioning liner mounts between the body and frame of your hot rod, making it ride as good as it looks. Liner measures 1/8" thick and 2" wide and comes in a 25 ft. length. Has an adhesive tape backing to keep it in place when mounting your body.
            
Goto Previous PagePrevious Page
1 2 3