Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Classic Brakes At Speedway Motors

Speedway Motors is the #1 authority on disc brakes conversion kits. With the most experience in the Classic Pickup Truck business, you can be assured that you are getting a quality, excellent fitting kit. Insist on a Speedway front disc brake conversion kit for your classic truck. Don't forget to check out our huge selection of brake rotors, high volume master cylinders, proportioning valves and blocks. Stock up on all the essential brake lines, brake calipers, brake pads and fittings, too!

Featured Products
1969-1972 GM Midsize 11 Inch Brake Rotor, 5 on 4 3/4 Inch
1969-1972 GM Midsize 11 Inch Brake Rotor, 5 on 4 3/4 Inch
(Part #91065390)
x
            

We stock those hard-to-find replacement brake rotors for your 1969-1972 GM midsize car. These rotors are specifically designed for the rigors of dirt track racing.  Drilled with a 5-on-4.75" bolt circle. Includes 7/16" fine quick-start wheel studs (installed).

  • 1969-1972 GM Midsize
  • 11 Inch Brake Rotor
  • 5 on 4-3/4 Inch
  • 7/16" fine studs installed
  • 11" diameter x 1"
  • IMCA Approved

This rotor is designed for dirt track applications and should NOT be used for asphalt racing.

 

 

Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake
Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake
(Part #91031921)
x
            

If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM emergency brake calipers, brake pads and hardware.

  • Fits both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
  • For Ford passenger car axles ONLY 
  • Fits axle with maximum flange diameter of 6-1/4" O.D.
  • For 15" and larger wheel applications ONLY

NOTE: This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts. If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so. Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

Axle Flange Identification Chart (GIF)

910-31921 Instructions (PDF)

Speedway 1969-77 GM Midsize Caliper
Speedway 1969-77 GM Midsize Caliper
(Part #91031035)
x
            Rebuilt 1969-77 mid and full size caliper. 7/16"-20 inlet so you can use the readily available brake hoses and hardware from Pre-1978 GM midsize cars. IMCA approved. 

No core charge required. Fits 1" thick rotor. 2.8" diameter pistons installed. It has 7-1/16" center to center mounting holes. The width between mounting tabs is 2-3/4".
1978-Up GM Metric Brake Calipers, IMCA Approved
1978-Up GM Metric Brake Calipers, IMCA Approved
(Part #91031045)
x
            

These stock replacement single piston Metric calipers were standard equipment on 1978-88 GM mid-size cars (Cutlass, Grand Prix, Regals, Monte Carlo, etc.). They feature a 2.38" single piston, shielded bottom inlet, and will save 3-1/2 lbs. per side compared to mid-size 1969-1977 caliper.

 

  • IMCA approved
  • No core charge required
  • 7/16"-20 inlet
  • Can be used with brake hoses from Pre-1978 GM intermediate cars
  • Brake pads & bolts sold separately

 

Note: Does NOT include brake pads or slider bolts and bushings.

"Classic Truck, Brake" Page 1 of 25

  • Lokar BAG-6083 1976-03 Chevy Truck Billet Alum Automatic Brake Pad
    Lokar BAG-6083 1976-03 Chevy Truck Billet Alum Automatic Brake Pad
    (Part #491BAG6083)
    x
                
    • Made to cover the factory brake pad. Billet aluminum construction with hardware included. Made in the U.S.A. Lifetime warranty.
    • Made To Cover Factory Brake Pad
    • Quick And Easy Installation
    • No Drilling Required
    • No Alignment Problems
    • Hardware Incl.
    • Billet Aluminum
    • Made In The U.S.A.
    • Lifetime Warranty
  • Wilwood 140-7140-DP FDL Rear Brake Kit, New Big Ford 2.50 Off
    New
    Wilwood 140-7140-DP FDL Rear Brake Kit, New Big Ford 2.50 Off
    (Part #8351407140DP)
    x
                This group of FDL Pro-Series rear disc kits provides a complete solution for popular muscle car rear axles that require a parking brake. Forged billet Dynalite four piston calipers, 12.19"  one-piece drum/rotors, and high friction pads provide optimized and balanced braking for all types of custom performance street/strip and show machines. The neatly hidden internal shoe system provides a clean installation with superior static holding power for parking. Optional caliper finishes and rotor designs enable the builder to personalize the style and optimize brake performance for every individual application.

    Installation Instructions (PDF)

  • Lokar BAG-6005 Billet Aluminum Brake Pad w/Rubber, Brushed
    Lokar BAG-6005 Billet Aluminum Brake Pad w/Rubber, Brushed
    (Part #491BAG6005)
    x
                
    • Made to cover the factory brake pad. Billet aluminum construction with hardware included. Made in the U.S.A. Lifetime warranty.
    • Designed w/1/2 X 20 Thread
    • Incl. 1/2 X 20 Stud In Kit
    • Can Be Mounted Centered Or Off Center
    • Rubber Insert Designed Pad
    • Made In The U.S.A.
    • Lifetime Warranty
  • Wilwood 160-8747 GT 48 Curved Vane Spec 37 Iron Rotor, 12.6 Inch
    New
    Wilwood 160-8747 GT 48 Curved Vane Spec 37 Iron Rotor, 12.6 Inch
    (Part #8351608747)
    x
                Wilwood's GT 48 Curved Vane Spec-37 rotors are manufactured from a proprietary iron alloy developed to withstand extreme temperatures with the highest possible degree of resistance against distortion, warping, cracking, and wear. The formulation for this alloy is a derivative of technology and materials that were significant in the development of the extreme duty military spec rotors that are manufactured by Wilwood. Every Spec 37 rotor is precision machined to less than .001" run-out, flatness, and parallelism. Combined with our proven GT Series asymmetrical face slot pattern and individual dynamic balancing, you are assured the smoothest, vibration free performance at any speed. These rotors provide the highest cooling capacity and longest service life for extreme braking short tracks and road course competition.
    • Spec-37 Heavy wall Castings
    • Suitable for moderate temperature racing to street use.
  • Wilwood 140-13323 FNSL 4R Rear Brake Kit, Big Ford 2.36 Off, Bronco
    New
    Wilwood 140-13323 FNSL 4R Rear Brake Kit, Big Ford 2.36 Off, Bronco
    (Part #83514013323)
    x
                These versions of Forged Narrow Superlite 4R rear disc kits provide the ultimate Big Brake solution for Bronco 65-77 rear axles with Big Ford flange and bearing. (normally: OE 11 inch diameter brakes and 3300 GVW.) Each includes a high efficiency drum style parking brake assembly. FNSL4R four piston calipers, 13"  or 14"  two-piece rotors, and high performance BP-10 compound pads provide optimized and balanced braking to compliment front big brake upgrades available for Bronco platform. The neatly hidden internal shoe system provides a clean installation with superior static holding power for parking. Optional caliper finishes and rotor designs allow builders to personalize the style and performance for every application.

    Installation Instructions (PDF)

  • Wilwood 160-12292 GT 36 Curved Vane Spec 37 Iron Rotor, 12.19 Inch
    New
    Wilwood 160-12292 GT 36 Curved Vane Spec 37 Iron Rotor, 12.19 Inch
    (Part #83516012292)
    x
                Wilwood's GT 36 Curved Vane Spec-37 rotors are manufactured from a proprietary iron alloy developed to withstand extreme temperatures with the highest possible degree of resistance against distortion, warping, cracking, and wear. The formulation for this alloy is a derivative of technology and materials that were significant in the development of the extreme duty military spec rotors that are manufactured by Wilwood. Every Spec 37 rotor is precision machined to less than .001" run-out, flatness, and parallelism. Combined with our proven GT Series asymmetrical face slot pattern and individual dynamic balancing, you are assured the smoothest braking available.
    • Spec-37 Heavy wall Castings
    • Suitable for high temperature racing to street use.
  • Wilwood 120-8000-RSP BNSL6R Caliper,RH, 1.62/1.12/1.12 Pist, 1.25 Disc
    New
    Wilwood 120-8000-RSP BNSL6R Caliper,RH, 1.62/1.12/1.12 Pist, 1.25 Disc
    (Part #8351208000RSP)
    x
                The billet SL6R series adds the versatility and convenience of radial mounting to this widely popular caliper group. Radial mounting simplifies adaptation and provides two planes of adjustment for accurate alignment over the disc. These calipers integrate "Big Brake" style with Wilwood's latest technology to generate big stopping power in extreme environments over a broad range of vehicle applications. The key to the superior performance of the SL6R comes from the extremely durable and efficient body design. Starting at 4.84 pounds it is the product of computer generated solid modeling and FEA stress analysis technology. Full length stiffening ribs and a reinforced radial transition from the piston bore housings to the closed end bridges has produced the strongest SL caliper bodies ever built. When compared to open bridge calipers that use tube or stand spacers between the body halves, the closed end bridge design is measurably stronger with less separation or deflection under load. Additional strength and resistance to deflection comes from the four high-strength steel end bridge bolts. A fifth center bridge bolt provides even more overall strength and easy access to the pads without the need to remove the caliper from the mount.    A unique six-piston differential bore configuration provides balanced loading for even pad wear in sustained high heat environments. The standard SL6R calipers feature one-piece stainless steel pistons. Stainless is used for its slow he
            
  • Aluminum Tube Nut Coupler, AN4 1/4 Inch
    Aluminum Tube Nut Coupler, AN4 1/4 Inch
    (Part #6176056)
    x
                

    Use these tube nut couplers in conjunction with our tube sleeves (sold seperately) to seal bulkhead fittings to fuel cells, oil tanks and other applications using hard line fitting situations. You need to flare the tube to 37° to match the AN fittings. Not for use with 45° flared lines.

    Fitting Thread Application Chart (GIF)

  • Wilwood 140-12569-D D154 Rear Brake Kit, Chevy C-10, 2.42 Off 5-lug
    New
    Wilwood 140-12569-D D154 Rear Brake Kit, Chevy C-10, 2.42 Off 5-lug
    (Part #83514012569D)
    x
                D154 Pro-Series rear disc kits provides a complete solution for popular muscle car rear axles that require a parking brake. Forged D154 dual piston calipers, 12.19"  one-piece drum/rotors, and high friction pads provide optimized and balanced braking for all types of custom performance street/strip and show machines. The neatly hidden internal shoe system provides a clean installation with superior static holding power for parking. D154 rear caliper kits offer a complimentary match to vehicles using Wilwood D52 or D154 calipers on OE spindles. Optional caliper finishes and rotor designs enable the builder to personalize the style and optimize brake performance.

    Installation Instructions (PDF)

  • Wilwood 160-11837-B GT 48 Curved Vane Spec 37 Iron Rotor, 11.75 Inch
    New
    Wilwood 160-11837-B GT 48 Curved Vane Spec 37 Iron Rotor, 11.75 Inch
    (Part #83516011837B)
    x
                Wilwood's GT 48 Curved Vane Spec-37 rotors are manufactured from a proprietary iron alloy developed to withstand extreme temperatures with the highest possible degree of resistance against distortion, warping, cracking, and wear. The formulation for this alloy is a derivative of technology and materials that were significant in the development of the extreme duty military spec rotors that are manufactured by Wilwood. Every Spec 37 rotor is precision machined to less than .001" run-out, flatness, and parallelism. Combined with our proven GT Series asymmetrical face slot pattern and individual dynamic balancing, you are assured the smoothest, vibration free performance at any speed. These rotors provide the highest cooling capacity and longest service life for extreme braking short tracks and road course competition.
    • Spec-37 Heavy wall Castings
    • Suitable for high temperature racing to street use.
  • Wilwood 120-13529-BK Forged Dynalite-M Disc Brake Caliper, Black
    New
    Wilwood 120-13529-BK Forged Dynalite-M Disc Brake Caliper, Black
    (Part #83512013529BK)
    x
                

    The Forged Billet Dynalite-M is specifically designed to enhance outboard clearance and is the basis for Wilwood’s new Classic Style brake kits. The latest applied developments and innovations in caliper design and manufacturing processes have resulted in substantial improvements in strength and performance over all comparable models.

    • Aluminum construction
    • Black Powder coat finish
    • 3.3 Pounds
    • Mount Center: 5.25 Inches
    • Mount Type: Lug
    • Mount Side: Universal
    • Type: Stainless
    • 4 Piston
    • Minimum Rotor Diameter: 10.00"
    • Maximum Rotor Diameter: 13.06"
    • Rotor Width: 1"
    • Piston Bore: 1.75"
    • Inlet Thread Size: 1/8-27 NPT
    • Strongest calipers in it's class, with weights starting at 2.80 pounds
  • Wilwood 160-2979 GT 48 Curved Vane Spec 37 Iron Rotor, 12.72 Inch
    New
    Wilwood 160-2979 GT 48 Curved Vane Spec 37 Iron Rotor, 12.72 Inch
    (Part #8351602979)
    x
                Wilwood's GT 48 Curved Vane Spec-37 rotors are manufactured from a proprietary iron alloy developed to withstand extreme temperatures with the highest possible degree of resistance against distortion, warping, cracking, and wear. The formulation for this alloy is a derivative of technology and materials that were significant in the development of the extreme duty military spec rotors that are manufactured by Wilwood. Every Spec 37 rotor is precision machined to less than .001" run-out, flatness, and parallelism. Combined with our proven GT Series asymmetrical face slot pattern and individual dynamic balancing, you are assured the smoothest, vibration free performance at any speed. These rotors provide the highest cooling capacity and longest service life for extreme braking short tracks and road course competition.
    • Spec-37 Heavy wall Castings
    • Suitable for moderate temperature racing to street use.
  • Wilwood 160-7100 SRP 30 Vane Iron Rotor, 11 Inch
    New
    Wilwood 160-7100 SRP 30 Vane Iron Rotor, 11 Inch
    (Part #8351607100)
    x
                SRP Drilled Performance Rotors feature a specially engineered directional cross drill and face slot pattern that improve brake response and pad performance throughout the entire range of light to heavy braking. The venting and cleaning action of the holes and slots will reduce pad glaze and disperse gasses and heat generated during the pad to rotor interface. The holes and slots also inhibit irregular pad compound build-up on the rotor faces resulting in smoother engagement and improved pedal response in all conditions. The material removed also contributes to lower rotating and unsprung suspension weight.
    • Premium grade, medium weight castings.
    • Suitable for moderate temperature racing to street use.
    • For ultimate durability in racing use comparable ULHP or GT rotors.
  • Hawk HB119A.594 Performance 1978-Up HPS Brake Pads, DTC-15
    Hawk HB119A.594 Performance 1978-Up HPS Brake Pads, DTC-15
    (Part #919119A)
    x
                

    Get superior stopping power with Hawk Performance! Hawk Performance brake pads have been successful in virtually all forms of motorsports for over 16 years. This success helps Hawk Performance enjoy the benefits of the “Win on Sunday, Sell on Monday,” philosophy. Hawk is one of few brake pad manufacturers that can deliver on the promise, “Race Proven – Street Legal.”

    • Increased stopping power
    • High friction/torque hot or cold
    • Gentle on rotors
    • Extended pad life
    • Low dust
    • Virtually noise-free

    Tech Tip:  Only use full metallic pads on coated rotors.

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

     

  • Wilwood 160-11839-B GT 48 Curved Vane Spec 37 Iron Rotor, 12.19 Inch
    New
    Wilwood 160-11839-B GT 48 Curved Vane Spec 37 Iron Rotor, 12.19 Inch
    (Part #83516011839B)
    x
                Wilwood's GT 48 Curved Vane Spec-37 rotors are manufactured from a proprietary iron alloy developed to withstand extreme temperatures with the highest possible degree of resistance against distortion, warping, cracking, and wear. The formulation for this alloy is a derivative of technology and materials that were significant in the development of the extreme duty military spec rotors that are manufactured by Wilwood. Every Spec 37 rotor is precision machined to less than .001" run-out, flatness, and parallelism. Combined with our proven GT Series asymmetrical face slot pattern and individual dynamic balancing, you are assured the smoothest, vibration free performance at any speed. These rotors provide the highest cooling capacity and longest service life for extreme braking short tracks and road course competition.
    • Spec-37 Heavy wall Castings
    • Suitable for high temperature racing to street use.
  • Wilwood 140-13581-D Dynapro 6 Front Disc Brake Kit, 12.88 Inch, Black
    New
    Wilwood 140-13581-D Dynapro 6 Front Disc Brake Kit, 12.88 Inch, Black
    (Part #83514013581D)
    x
                Please view the product's page for more information
            
  • Lokar X70-BHR Midnight Series Black Billet Hand Brake Boot Ring
    Lokar X70-BHR Midnight Series Black Billet Hand Brake Boot Ring
    (Part #491X70BHR)
    x
                Lokar Shifter and Hand Brake Boots are black Naugahyde and all sets include a boot, polished stainless base ring, OR billet aluminum ring with ball-milled edge and stainless screws. Billet aluminum rings also available in black anodized.
    • Our Classic Shifter Boot is designed with a polished stainless bezel on top of the boot which fits over the shifter lever.
    • It also includes a foam rubber seal to eliminate air flow from the floor through the boot.
    • The Hand Brake Boots are available in transmount or floor mount styles.
    • All boots hug the shifter lever and there are no unsightly pull ties or laces.
  • Wilwood 15A-5740K 9725 PolyMatrix A Brake Pad Set, .98 Inch Thick
    New
    Wilwood 15A-5740K 9725 PolyMatrix A Brake Pad Set, .98 Inch Thick
    (Part #83515A5740K)
    x
                
    • Ultimate high friction pad with aggressive initial response
    • Immediate low tempeature response.
    • Low wear rate
    • Ultimate high friction pad with aggressive initial response
    • Immediate cold response with highest friction values at all temperatures.
    • Severe duty use on oval tracks, road courses, and other applications that require immediate high torque response.
    • Long wear rate for sustained high heat braking.
    • Compatible with all iron and steel rotors.

    Compound Data Sheet (PDF)

  • Lokar 70-BHBT Billet Hand Brake Boot Ring with Transmount Boot
    Lokar 70-BHBT Billet Hand Brake Boot Ring with Transmount Boot
    (Part #49170BHBT)
    x
                
    • Lokar shifter boots are black Naugahyde and all sets include a boot, polished stainless base ring, or billet aluminum ring with ball-milled edge and stainless screws. Available in transmount style or floor mount style. Boot hugs the hand brake lever.
    • Black Naugahyde
    • Boot Hugs The Hand Brake Lever
    • Made In The U.S.A.
    • Lifetime Warranty
  • Lokar EHB-7000F Floor Mount Emergency Hand Brake, Chrome Finish
    Lokar EHB-7000F Floor Mount Emergency Hand Brake, Chrome Finish
    (Part #4917000)
    x
                

    This Lokar Floor Mount Emergency Hand Brake features a chrome plated steel e brake handle and is designed after the automotive industry standards. The ratchet cut gear plate and lock are heat treated for strength and safety. Special feature includes 4-point mounting capabilities for floor mount or side mounting for custom applications.

    Comes complete with clevis for installation with Lokar Emergency Brake Cables, Lokar # EC-80FU, Speedway Motors # 491-80FU suggested below. Cables are sold separately.

    Lokar Install Tip:  Every think about mounting the floor mount hand brake sideways in front of your seat?  You can!

  • Wilwood 160-7106-BK SRP-BLK 32 Vane Iron Rotor, 12.19 Inch
    New
    Wilwood 160-7106-BK SRP-BLK 32 Vane Iron Rotor, 12.19 Inch
    (Part #8351607106BK)
    x
                SRP Drilled Performance Rotors feature a specially engineered directional cross drill and face slot pattern that improve brake response and pad performance throughout the entire range of light to heavy braking. The venting and cleaning action of the holes and slots will reduce pad glaze and disperse gasses and heat generated during the pad to rotor interface. The holes and slots also inhibit irregular pad compound build-up on the rotor faces resulting in smoother engagement and improved pedal response in all conditions. The material removed also contributes to lower rotating and unsprung suspension weight.
    • Premium grade, medium weight castings.
    • Suitable for moderate temperature racing to street use.
    • For ultimate durability in racing use comparable ULHP or GT rotors.
  • Lokar EC-8001U120 E-Brake Universal Connector Cable, 120 Inch, Black
    Lokar EC-8001U120 E-Brake Universal Connector Cable, 120 Inch, Black
    (Part #491EC8001U120)
    x
                
    • Quality One-Piece Aluminum Adjusters
    • Aluminum Ferrule To Eliminate Fraying Of Housing
    • Extruded Liner For Extended Life Of The Cable
    • Stainless Inner Cable Resists Moisture
    • Allow Rear End Backing Plate Fitting To Be Removed
    • U-Cut-To-Fit Outer Housings
    • Black Housing
  • 90 Degree -3 AN to 1/8 NPT Steel Adapter Fitting
    90 Degree -3 AN to 1/8 NPT Steel Adapter Fitting
    (Part #6174279)
    x
                

    Brake Adaptor.

    • 1/8" NPT

     

  • DOT Braided Stainless Brake Hoses, Mustang II, 7/16-24
    DOT Braided Stainless Brake Hoses, Mustang II, 7/16-24
    (Part #6178565)
    x
                

    DOT approved brake line kits include two stainless steel -3 AN brake lines with the banjo fitting installed, banjo bolts and washers, 3/8"-24 IFF frame adapter fittings and frame tabs with clips. Includes -3 AN fittings and adapters to connect them to 3/16" brake line using a 3/8"-24 IFM flare nut.

    • Stainless steel braid over Teflon® hose
    • Reduces volumetric expansion of brake lines
    • Reduces brake fade
    • Less susceptible to debris than rubber line
  • Wilwood 140-10941-R AERO4 Rear Brake Kit, Chevy C-10, 2.42 Off 5-lug
    New
    Wilwood 140-10941-R AERO4 Rear Brake Kit, Chevy C-10, 2.42 Off 5-lug
    (Part #83514010941R)
    x
                AERO4 Rear Parking Brake kits provide the ultimate Big Brake solution for popular muscle car rear axles that require a parking brake. Forged AERO4 four piston calipers, 14"  two-piece rotors, and high performance BP-10 compound pads provide optimized and balanced braking to compliment front big brake upgrades on all types of custom, show and high performance street machines. The neatly hidden internal shoe system provides a clean installation with superior static holding power for parking. Optional caliper finishes and rotor designs allow builders to personalize the style and performance for every application.

    Installation Instructions (PDF)

  • Wilwood 140-13322-D Dynapro Lug Mount Rear Brake Kit, Big Ford, Bronco
    New
    Wilwood 140-13322-D Dynapro Lug Mount Rear Brake Kit, Big Ford, Bronco
    (Part #83514013322D)
    x
                These versions of DPL Pro-Series rear disc kits provides a complete solution for Bronco 65-77 rear axles with Big Ford flange and bearing. (normally: OE 11 inch diameter brakes and 3300 GVW.) Forged Billet Dynapro Lug Mount four piston calipers, 12.19"  one-piece drum/rotors, and high friction pads provide optimized and balanced braking to compliment front big brake upgrades available for Bronco platform. The neatly hidden internal shoe system provides a clean installation with superior static holding power for parking. Optional caliper finishes and rotor designs enable the builder to personalize the style and optimize brake performance for every individual application.

    Installation Instructions (PDF)

  • Lokar XBAG-6176 Midnight Series 97-01 Jeep Auto Curved Brake Pad w/Rub
    Lokar XBAG-6176 Midnight Series 97-01 Jeep Auto Curved Brake Pad w/Rub
    (Part #491XBAG6176)
    x
                For a compact and clean look. Add style and function to your classic car. Designed with hidden screws. Curved to match and bolt directly to the factory pedal. Brushed billet aluminum with rubber inserts. Made in the U.S.A. Lifetime warranty.
            
  • Goodridge 15 Inch Braided Brake Line with 90 Degree End
    Goodridge 15 Inch Braided Brake Line with 90 Degree End
    (Part #91031898)
    x
                

    These high quality stainless steel, braided fluid lines have a 90° fitting on one end and a straight fitting on the other. They work well for brake lines, clutch lines and gauge lines. These are available with AN3 or AN4 fittings. Sold individually.

    • Stainless steel
    • 90° fitting on one end and a straight fitting on the other
    • Brake lines, clutch lines and gauge lines
    • Available with AN3 or AN4 fittings
    • Sold individually

    Select applicable length. AN size is the "-#" at the end of the part number.

  • Lokar EC-80THT216 Univ. Transmount E-Brake Cables, 216 In, Stainless
    Lokar EC-80THT216 Univ. Transmount E-Brake Cables, 216 In, Stainless
    (Part #491EC80THT216)
    x
                Transmount emergency brake cables for use with Lokar's transmount emergency hand brake and includes bracket for mounting cables to hand brake. Kit comes equipped with quality one-piece aluminum adjusters and aluminum ferrule to eliminate fraying of stainless housing. Outer housing is designed with specially extruded liner for extended life of the cable. Stainless steel inner cable resists moisture. Design allows rear end backing plate fittings to be removed without removing brake cables. Lokar cables also feature adjustable cable lock and clevis. Kit includes two 8 foot outer housings that u-cut-to-fit and are available in stainless housing or black housing. Application fits 8 and 9 inch Fords, Chevy, Chrysler and Lincoln Versailles drum and disc brakes.
    • Quality One-Piece Aluminum Adjusters
    • Aluminum Ferrule To Eliminate Fraying
    • Extruded Liner For Extended Life Of The Cable
    • Stainless Inner Cable Resists Moisture
    • Allow Rear End Backing Plate Fitting To Be Removed
    • Black Housing
  • 7/16 Inch to AN4 Banjo Fitting
    7/16 Inch to AN4 Banjo Fitting
    (Part #6174063)
    x
                7/16 Inch to AN4 Banjo Fitting
            
  • US Brake Tri Reverse Mount Master Cylinder Pedal Assembly Kit, 6.2:1
    US Brake Tri Reverse Mount Master Cylinder Pedal Assembly Kit, 6.2:1
    (Part #91029984)
    x
                

    This Wilwood pedal/US Brake master cylinder assembly combines the brake and clutch pedals together in one unit and positions the master cylinders inside the firewall and away from engine heat. It features all aluminum frame and arm construction with steel pivots, mounting studs, and anti-skid pedal pads. Wilwood's clevis and pivot pin balance bar provide smooth and accurate settings of the brake pedal bias. It can be set and locked down with the jam nut, or attached to a remote cable for quick on-track adjustments.

    • 6.2:1 pedal ratio 
    • External return spring maintains positive pedal feel, prolongs pad life
    • Polished smooth bores
    • One-piece alumiunum construction
    • Each master cylinder has a single 1/8" NPT outlet
    • Specify m/c bore sizes needed (3/4", 7/8", 1")

    Learn more about selecting the proper master cylinder for your vehicle by reading our tech article. Brake System Selection.

  • Lokar BAG-6185 1966-77 Ford Bronco Billet Alum Man Brake/Clutch Pedals
    Lokar BAG-6185 1966-77 Ford Bronco Billet Alum Man Brake/Clutch Pedals
    (Part #491BAG6185)
    x
                For a compact and clean look. Add style and function to your classic car. Designed with hidden screws. Curved to match and bolt directly to the factory pedal. Brushed billet aluminum with rubber inserts. Made in the U.S.A. Lifetime warranty.
    • For A Compact And Clean Look
    • Add Style And Function To Your Classic Car
    • Designed With Hidden Screws
    • Curved To Match And Bolt Directly To Factory Pedal
    • Black Anodized Aluminum w/Rubber Inserts
    • Lifetime Warranty
  • Wilwood 15Q-7268K 7816 PolyMatrix Q Brake Pad Set, BNDL, .60 In Thick
    New
    Wilwood 15Q-7268K 7816 PolyMatrix Q Brake Pad Set, BNDL, .60 In Thick
    (Part #83515Q7268K)
    x
                
    • Medium friction, smooth engagement, low abrasion on iron rotors.
    • Flat torque curve. Can be used with aluminum rotors on Sprint Car applications.
    • Low wear rate at low to medium temperatures
    • Medium friction, smooth engagement, low abrasion on iron rotors.
    • High performance ceramic based street formula.
    • Lowest dust and noise.
    • Compatible with all types of steel or iron rotors.
    • Aluminum rotors for racing.

    Compound Data Sheet (PDF)

  • Wilwood 160-7745-BK SRP-BLK 48 Curved Vane Iron Rotor, 12.8 Inch
    New
    Wilwood 160-7745-BK SRP-BLK 48 Curved Vane Iron Rotor, 12.8 Inch
    (Part #8351607745BK)
    x
                SRP Drilled Performance Rotors feature a specially engineered directional cross drill and face slot pattern that improve brake response and pad performance throughout the entire range of light to heavy braking. The venting and cleaning action of the holes and slots will reduce pad glaze and disperse gasses and heat generated during the pad to rotor interface. The holes and slots also inhibit irregular pad compound build-up on the rotor faces resulting in smoother engagement and improved pedal response in all conditions. The material removed also contributes to lower rotating and unsprung suspension weight.
    • Premium grade, heavy wall castings.
    • Suitable for moderate temperature racing to street use.
    • For ultimate durability in racing use comparable HD or GT rotors.
  • Threaded Steel Weld Bung Fitting, 1/4 Inch NPT Female
    Threaded Steel Weld Bung Fitting, 1/4 Inch NPT Female
    (Part #6176702)
    x
                

    We offer these premium-quality weld-in bungs for a variety of uses. They're CNC-machined from steel and are great for oil or fuel tanks, radiators, valve covers, manifolds, and rear axle housings.

    Female weld bung fittings available in steel.  1/4 Inch NPT works well with rubber round pedal pad (part number 91031200) to mount pedal stud. 

    Threaded Steel Weld Bung Fitting

    • 1/4 Inch NPT

    Fitting Thread Application Chart (GIF)

     

  • Lokar BCA-9503 90 Billet Aluminum Direct Fit Brake & Clutch Pedal Arm
    Lokar BCA-9503 90 Billet Aluminum Direct Fit Brake & Clutch Pedal Arm
    (Part #491BCA9503)
    x
                
    • Billet Brake And Clutch Arm
  • DOT Braided Stainless Brake Hoses, GM/Ford, 7/16-20
    DOT Braided Stainless Brake Hoses, GM/Ford, 7/16-20
    (Part #6178564)
    x
                

    This line kit would be used to connect from "hard" lines on the rear axle to rear disc calipers when changing from drum to disc brakes. DOT approved brake line kits include two stainless steel -3 AN brake lines with the banjo fitting installed, banjo bolts and washers, 3/8"-24 IFF frame adapter fittings and frame tabs with clips. Includes -3 AN fittings and adapters to connect them to 3/16" brake line using a 3/8"-24 IFM flare nut.

    • Stainless steel braid over Teflon® hose
    • Reduces volumetric expansion of brake lines
    • Reduces brake fade
    • Less susceptible to debris than rubber line
    • Used to connect from hard line on rear axle to rear calipers when changing from drum to disc brakes

    Kit includes:

    • (2) 8" stainless steel srake lines w/ 7/16" banjo on one end 
    • (2) 7/16" banjo bolts w/ crush washers
    • (2) 3/8" x 24 IFF apapters to the hard lines
    • (2) frame tabs & clips
  • 1963-1966 Chevy 1/2 Ton Pickup Front Disc Brake Conversion Kit
    1963-1966 Chevy 1/2 Ton Pickup Front Disc Brake Conversion Kit
    (Part #91006366)
    x
                

    This kit allows you to upgrade your 1963-1966 Chevy pickup to disc brakes and gain the advantage of a more common 5-on-4.75" GM midsize passanger car bolt circle. A wheel change is required, but you want custom 5-lug wheels on your truck anyway, right? The new 11" rotors fit on your stock drum brake spindles.

    Kit includes 11" rotors, GM Midsize calipers, caliper brackets, bearings, seals, spindle nuts, dust caps, banjo bolts, brake hoses, 9" single diaphragm brake booster, master cylinder, disc/drum proportioning valve, and mounting hardware.

    Only for 1/2 ton trucks 

  • Wilwood 160-12286 GT 36 Curved Vane Spec 37 Iron Rotor, 11.75 Inch
    New
    Wilwood 160-12286 GT 36 Curved Vane Spec 37 Iron Rotor, 11.75 Inch
    (Part #83516012286)
    x
                Wilwood's GT 36 Curved Vane Spec-37 rotors are manufactured from a proprietary iron alloy developed to withstand extreme temperatures with the highest possible degree of resistance against distortion, warping, cracking, and wear. The formulation for this alloy is a derivative of technology and materials that were significant in the development of the extreme duty military spec rotors that are manufactured by Wilwood. Every Spec 37 rotor is precision machined to less than .001" run-out, flatness, and parallelism. Combined with our proven GT Series asymmetrical face slot pattern and individual dynamic balancing, you are assured the smoothest braking available.
    • Spec-37 Heavy wall Castings
    • Suitable for high temperature racing to street use.
  • Dual Outlet Master Cylinder Stainless Steel Dual Brake Line Kit
    Dual Outlet Master Cylinder Stainless Steel Dual Brake Line Kit
    (Part #91031802)
    x
                

    This is a pair of steel or stainless steel brake lines intended to simplify plumbing from the master cylinder to a proportioning block, such as our 910-31358 or 835-26011179.

    • Features tight 90° bends at the master cylinder end
    • Both ends of both lines are 3/8"-24 inverted flare nuts
    • The longer of the two lines measures app. 12" from the bend to the end
Goto Previous PagePrevious Page
1 2 3 4 5 ... 25