Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Classic Brakes At Speedway Motors

Speedway Motors is the #1 authority on disc brakes conversion kits. With the most experience in the Classic Pickup Truck business, you can be assured that you are getting a quality, excellent fitting kit. Insist on a Speedway front disc brake conversion kit for your classic truck. Don't forget to check out our huge selection of brake rotors, high volume master cylinders, proportioning valves and blocks. Stock up on all the essential brake lines, brake calipers, brake pads and fittings, too!

Featured Products
1969-1972 GM Midsize 11 Inch Brake Rotor, 5 on 4 3/4 Inch
1969-1972 GM Midsize 11 Inch Brake Rotor, 5 on 4 3/4 Inch
SKU-91065390
x
            

We stock those hard-to-find replacement brake rotors for your 1969-1972 GM midsize car. These rotors are specifically designed for the rigors of dirt track racing.  Drilled with a 5-on-4.75" bolt circle. Includes 7/16" fine quick-start wheel studs (installed).

  • 1969-1972 GM Midsize
  • 11 Inch Brake Rotor
  • 5 on 4-3/4 Inch
  • 7/16" fine studs installed
  • 11" diameter x 1"
  • IMCA Approved

This rotor is designed for dirt track applications and should NOT be used for asphalt racing.

 

 

Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake
Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake
SKU-91031921
x
            

If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM emergency brake calipers, brake pads and hardware.

  • Fits both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
  • For Ford passenger car axles ONLY 
  • Fits axle with maximum flange diameter of 6-1/4" O.D.
  • For 15" and larger wheel applications ONLY

NOTE: This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts. If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so. Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

Axle Flange Identification Chart (GIF)

910-31921 Instructions (PDF)

Speedway 1969-77 GM Midsize Caliper
Speedway 1969-77 GM Midsize Caliper
SKU-91031035
x
            Rebuilt 1969-77 mid and full size caliper. 7/16"-20 inlet so you can use the readily available brake hoses and hardware from Pre-1978 GM midsize cars. IMCA approved. 

No core charge required. Fits 1" thick rotor. 2.8" diameter pistons installed. It has 7-1/16" center to center mounting holes. The width between mounting tabs is 2-3/4".
1978-Up GM Metric Brake Calipers, IMCA Approved
1978-Up GM Metric Brake Calipers, IMCA Approved
SKU-91031045
x
            

These stock replacement single piston Metric calipers were standard equipment on 1978-88 GM mid-size cars (Cutlass, Grand Prix, Regals, Monte Carlo, etc.). They feature a 2.38" single piston, shielded bottom inlet, and will save 3-1/2 lbs. per side compared to mid-size 1969-1977 caliper.

 

  • IMCA approved
  • No core charge required
  • 7/16"-20 inlet
  • Can be used with brake hoses from Pre-1978 GM intermediate cars
  • Brake pads & bolts sold separately

 

Note: Does NOT include brake pads or slider bolts and bushings.

"Classic Truck, Brake" Page 1 of 25

  • Brake Pedal Pad, Round, Rubber
    Brake Pedal Pad, Round, Rubber
    SKU-91031200
    x
                Rubber brake pedal cover has a concentric circular pattern like original equipment. 1/4" NPT stud (the shank is .650" in length). Molded hard-rubber construction and is 3-1/2" dia. 
            
  • Lokar BAG-6083 1976-03 Chevy Truck Billet Alum Automatic Brake Pad
    Lokar BAG-6083 1976-03 Chevy Truck Billet Alum Automatic Brake Pad
    SKU-491BAG6083
    x
                
    • Made to cover the factory brake pad. Billet aluminum construction with hardware included. Made in the U.S.A. Lifetime warranty.
    • Made To Cover Factory Brake Pad
    • Quick And Easy Installation
    • No Drilling Required
    • No Alignment Problems
    • Hardware Incl.
    • Billet Aluminum
    • Made In The U.S.A.
    • Lifetime Warranty
  • Wilwood 140-7140-DP FDL Rear Brake Kit, New Big Ford 2.50 Off
    New
    Wilwood 140-7140-DP FDL Rear Brake Kit, New Big Ford 2.50 Off
    SKU-8351407140DP
    x
                Please view the product's page for more information
            
  • Lokar BAG-6005 Billet Aluminum Brake Pad w/Rubber, Brushed
    Lokar BAG-6005 Billet Aluminum Brake Pad w/Rubber, Brushed
    SKU-491BAG6005
    x
                
    • Made to cover the factory brake pad. Billet aluminum construction with hardware included. Made in the U.S.A. Lifetime warranty.
    • Designed w/1/2 X 20 Thread
    • Incl. 1/2 X 20 Stud In Kit
    • Can Be Mounted Centered Or Off Center
    • Rubber Insert Designed Pad
    • Made In The U.S.A.
    • Lifetime Warranty
  • Mild Steel -3 AN Brake Line Kit
    Mild Steel -3 AN Brake Line Kit
    SKU-6178560
    x
                

    This brake line kit bridges the gap between our stainless steel -3 AN kit, and our steel inverted flare version. It includes a 25 foot roll of 3/16" steel brake line, four 18" stainless steel braided hoses and enough -3 AN fittings to plumb your brake lines. 

    Since we don't know what calipers and master cylinder you will be using, these fittings are sold separately.

     
    Learn more about flaring lines for our automotive fittings by reading our tech article. The Principles of Automotive Fittings
  • Aluminum Tube Nut Coupler, AN4 1/4 Inch
    Aluminum Tube Nut Coupler, AN4 1/4 Inch
    SKU-6176056
    x
                

    Use these tube nut couplers in conjunction with our tube sleeves (sold seperately) to seal bulkhead fittings to fuel cells, oil tanks and other applications using hard line fitting situations. You need to flare the tube to 37° to match the AN fittings. Not for use with 45° flared lines.

    Fitting Thread Application Chart (GIF)

  • Wilwood 120-13529-BK Forged Dynalite-M Disc Brake Caliper, Black
    New
    Wilwood 120-13529-BK Forged Dynalite-M Disc Brake Caliper, Black
    SKU-83512013529BK
    x
                

    The Forged Billet Dynalite-M is specifically designed to enhance outboard clearance and is the basis for Wilwood’s new Classic Style brake kits. The latest applied developments and innovations in caliper design and manufacturing processes have resulted in substantial improvements in strength and performance over all comparable models.

    • Aluminum construction
    • Black Powder coat finish
    • 3.3 Pounds
    • Mount Center: 5.25 Inches
    • Mount Type: Lug
    • Mount Side: Universal
    • Type: Stainless
    • 4 Piston
    • Minimum Rotor Diameter: 10.00"
    • Maximum Rotor Diameter: 13.06"
    • Rotor Width: 1"
    • Piston Bore: 1.75"
    • Inlet Thread Size: 1/8-27 NPT
    • Strongest calipers in it's class, with weights starting at 2.80 pounds
  • GM Metric Caliper Fitting, 10mm - 1.5 to -3 AN, Male Adapter Connector
    GM Metric Caliper Fitting, 10mm - 1.5 to -3 AN, Male Adapter Connector
    SKU-6174043
    x
                

    Made from high-quality steel, these bulkhead adapters from Speedway give you an easy way to connect lines through firewalls or frames.

    These fittings have AN at one end and 10mm-1.5" on the other end. It can be screwed into a GM metric caliper with 10mm-1.5" threads if you use our crush washers (part number 617-3642). 

    Steel Male Adapter Connector Fitting 

    • AN to IFM all steel adapter
    • 10mm - 1.5 to -3 AN

     

  • Ford F-150 11.75 Inch Brake Rotor
    Ford F-150 11.75 Inch Brake Rotor
    SKU-91031068
    x
                5 x 5-1/2". This rotor was originally used on front of most Ford F-150 two wheel drive trucks from 1973 to approximately 1993. 11.75" diameter. 
            
  • Stainless Steel Brake Line, 3/16 Inch
    Stainless Steel Brake Line, 3/16 Inch
    SKU-6178510
    x
                

    Our 3/16" stainless steel tubing is made from 304 grade (rated at 6000 psi) which is double annealed to allow easy flaring.

    NOTE: This line is intended to be used in conjunction with 37 degree AN # 3 style fittings which make use of a single flare. Stainless steel line will not work with 45 degree double flare 3/8"-24 flare nuts. We strongly suggest that the 37 degree single flare (flaring tool # 910-89524) be used when flaring this line for the AN # 3 tube nuts and sleeves.

    Learn more about flaring lines and how to select proper automotive fittings by reading our tech article. The Principles of Automotive Fittings.

    Brake System Builder Tip (GIF)

  • Hawk HB119A.594 Performance 1978-Up HPS Brake Pads, DTC-15
    Hawk HB119A.594 Performance 1978-Up HPS Brake Pads, DTC-15
    SKU-919119A
    x
                

    Get superior stopping power with Hawk Performance! Hawk Performance brake pads have been successful in virtually all forms of motorsports for over 16 years. This success helps Hawk Performance enjoy the benefits of the “Win on Sunday, Sell on Monday,” philosophy. Hawk is one of few brake pad manufacturers that can deliver on the promise, “Race Proven – Street Legal.”

    • Increased stopping power
    • High friction/torque hot or cold
    • Gentle on rotors
    • Extended pad life
    • Low dust
    • Virtually noise-free

    Tech Tip:  Only use full metallic pads on coated rotors.

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

     

  • Wilwood 140-13581-D Dynapro 6 Front Disc Brake Kit, 12.88 Inch, Black
    New
    Wilwood 140-13581-D Dynapro 6 Front Disc Brake Kit, 12.88 Inch, Black
    SKU-83514013581D
    x
                Please view the product's page for more information
            
  • Lokar X70-BHR Midnight Series Black Billet Hand Brake Boot Ring
    Lokar X70-BHR Midnight Series Black Billet Hand Brake Boot Ring
    SKU-491X70BHR
    x
                Lokar Shifter and Hand Brake Boots are black Naugahyde and all sets include a boot, polished stainless base ring, OR billet aluminum ring with ball-milled edge and stainless screws. Billet aluminum rings also available in black anodized.
    • Our Classic Shifter Boot is designed with a polished stainless bezel on top of the boot which fits over the shifter lever.
    • It also includes a foam rubber seal to eliminate air flow from the floor through the boot.
    • The Hand Brake Boots are available in transmount or floor mount styles.
    • All boots hug the shifter lever and there are no unsightly pull ties or laces.
  • Lokar 70-BHBT Billet Hand Brake Boot Ring with Transmount Boot
    Lokar 70-BHBT Billet Hand Brake Boot Ring with Transmount Boot
    SKU-49170BHBT
    x
                
    • Lokar shifter boots are black Naugahyde and all sets include a boot, polished stainless base ring, or billet aluminum ring with ball-milled edge and stainless screws. Available in transmount style or floor mount style. Boot hugs the hand brake lever.
    • Black Naugahyde
    • Boot Hugs The Hand Brake Lever
    • Made In The U.S.A.
    • Lifetime Warranty
  • Lokar EHB-7000F Floor Mount Emergency Hand Brake, Chrome Finish
    Lokar EHB-7000F Floor Mount Emergency Hand Brake, Chrome Finish
    SKU-4917000
    x
                

    This Lokar Floor Mount Emergency Hand Brake features a chrome plated steel e brake handle and is designed after the automotive industry standards. The ratchet cut gear plate and lock are heat treated for strength and safety. Special feature includes 4-point mounting capabilities for floor mount or side mounting for custom applications.

    Comes complete with clevis for installation with Lokar Emergency Brake Cables, Lokar # EC-80FU, Speedway Motors # 491-80FU suggested below. Cables are sold separately.

    Lokar Install Tip:  Every think about mounting the floor mount hand brake sideways in front of your seat?  You can!

  • Aeroquip FBM1110 45 Degree High Pressure -3 AN TFE Hose End
    Aeroquip FBM1110 45 Degree High Pressure -3 AN TFE Hose End
    SKU-6172015
    x
                High alloy steel for high pressure brake and power steering systems. When assembled, you have a quality hose assembly that can handle up to 3000 psi. 

    Works only with TFE Stainless Braided
    High Pressure Hose.

    Hose End Application Chart (GIF)

  • Lokar EC-8001U120 E-Brake Universal Connector Cable, 120 Inch, Black
    Lokar EC-8001U120 E-Brake Universal Connector Cable, 120 Inch, Black
    SKU-491EC8001U120
    x
                
    • Quality One-Piece Aluminum Adjusters
    • Aluminum Ferrule To Eliminate Fraying Of Housing
    • Extruded Liner For Extended Life Of The Cable
    • Stainless Inner Cable Resists Moisture
    • Allow Rear End Backing Plate Fitting To Be Removed
    • U-Cut-To-Fit Outer Housings
    • Black Housing
  • 90 Degree -3 AN to 1/8 NPT Steel Adapter Fitting
    90 Degree -3 AN to 1/8 NPT Steel Adapter Fitting
    SKU-6174279
    x
                

    Brake Adaptor.

    • 1/8" NPT

     

  • DOT Braided Stainless Brake Hoses, Mustang II, 7/16-24
    DOT Braided Stainless Brake Hoses, Mustang II, 7/16-24
    SKU-6178565
    x
                

    DOT approved brake line kits include two stainless steel -3 AN brake lines with the banjo fitting installed, banjo bolts and washers, 3/8"-24 IFF frame adapter fittings and frame tabs with clips. Includes -3 AN fittings and adapters to connect them to 3/16" brake line using a 3/8"-24 IFM flare nut.

    • Stainless steel braid over Teflon® hose
    • Reduces volumetric expansion of brake lines
    • Reduces brake fade
    • Less susceptible to debris than rubber line
  • Lokar XBAG-6176 Midnight Series 97-01 Jeep Auto Curved Brake Pad w/Rub
    Lokar XBAG-6176 Midnight Series 97-01 Jeep Auto Curved Brake Pad w/Rub
    SKU-491XBAG6176
    x
                For a compact and clean look. Add style and function to your classic car. Designed with hidden screws. Curved to match and bolt directly to the factory pedal. Brushed billet aluminum with rubber inserts. Made in the U.S.A. Lifetime warranty.
            
  • Goodridge 15 Inch Braided Brake Line with 90 Degree End
    Goodridge 15 Inch Braided Brake Line with 90 Degree End
    SKU-91031898
    x
                

    These high quality stainless steel, braided fluid lines have a 90° fitting on one end and a straight fitting on the other. They work well for brake lines, clutch lines and gauge lines. These are available with AN3 or AN4 fittings. Sold individually.

    • Stainless steel
    • 90° fitting on one end and a straight fitting on the other
    • Brake lines, clutch lines and gauge lines
    • Available with AN3 or AN4 fittings
    • Sold individually

    Select applicable length. AN size is the "-#" at the end of the part number.

  • Lokar EC-80THT216 Univ. Transmount E-Brake Cables, 216 In, Stainless
    Lokar EC-80THT216 Univ. Transmount E-Brake Cables, 216 In, Stainless
    SKU-491EC80THT216
    x
                Transmount emergency brake cables for use with Lokar's transmount emergency hand brake and includes bracket for mounting cables to hand brake. Kit comes equipped with quality one-piece aluminum adjusters and aluminum ferrule to eliminate fraying of stainless housing. Outer housing is designed with specially extruded liner for extended life of the cable. Stainless steel inner cable resists moisture. Design allows rear end backing plate fittings to be removed without removing brake cables. Lokar cables also feature adjustable cable lock and clevis. Kit includes two 8 foot outer housings that u-cut-to-fit and are available in stainless housing or black housing. Application fits 8 and 9 inch Fords, Chevy, Chrysler and Lincoln Versailles drum and disc brakes.
    • Quality One-Piece Aluminum Adjusters
    • Aluminum Ferrule To Eliminate Fraying
    • Extruded Liner For Extended Life Of The Cable
    • Stainless Inner Cable Resists Moisture
    • Allow Rear End Backing Plate Fitting To Be Removed
    • Black Housing
  • 7/16 Inch to AN4 Banjo Fitting
    7/16 Inch to AN4 Banjo Fitting
    SKU-6174063
    x
                7/16 Inch to AN4 Banjo Fitting
            
  • Lokar BAG-6185 1966-77 Ford Bronco Billet Alum Man Brake/Clutch Pedals
    Lokar BAG-6185 1966-77 Ford Bronco Billet Alum Man Brake/Clutch Pedals
    SKU-491BAG6185
    x
                For a compact and clean look. Add style and function to your classic car. Designed with hidden screws. Curved to match and bolt directly to the factory pedal. Brushed billet aluminum with rubber inserts. Made in the U.S.A. Lifetime warranty.
    • For A Compact And Clean Look
    • Add Style And Function To Your Classic Car
    • Designed With Hidden Screws
    • Curved To Match And Bolt Directly To Factory Pedal
    • Black Anodized Aluminum w/Rubber Inserts
    • Lifetime Warranty
  • Threaded Steel Weld Bung Fitting, 1/4 Inch NPT Female
    Threaded Steel Weld Bung Fitting, 1/4 Inch NPT Female
    SKU-6176702
    x
                

    We offer these premium-quality weld-in bungs for a variety of uses. They're CNC-machined from steel and are great for oil or fuel tanks, radiators, valve covers, manifolds, and rear axle housings.

    Female weld bung fittings available in steel.  1/4 Inch NPT works well with rubber round pedal pad (part number 91031200) to mount pedal stud. 

    Threaded Steel Weld Bung Fitting

    • 1/4 Inch NPT

    Fitting Thread Application Chart (GIF)

     

  • Lokar BCA-9503 90 Billet Aluminum Direct Fit Brake & Clutch Pedal Arm
    Lokar BCA-9503 90 Billet Aluminum Direct Fit Brake & Clutch Pedal Arm
    SKU-491BCA9503
    x
                
    • Billet Brake And Clutch Arm
  • 7 Inch Dual Brake Booster
    $129.99
    7 Inch Dual Brake Booster
    SKU-91031432
    x
                

    Compact, 7" diameter for installation under floor or on firewall of almost any vehicle. Has a zinc chromate finish.

    Booster Tech Tip (GIF) 

    Learn more about selecting the proper brake booster for your vehicle by reading our tech article. Brake System Selection.  

  • DOT Braided Stainless Brake Hoses, GM/Ford, 7/16-20
    DOT Braided Stainless Brake Hoses, GM/Ford, 7/16-20
    SKU-6178564
    x
                

    This line kit would be used to connect from "hard" lines on the rear axle to rear disc calipers when changing from drum to disc brakes. DOT approved brake line kits include two stainless steel -3 AN brake lines with the banjo fitting installed, banjo bolts and washers, 3/8"-24 IFF frame adapter fittings and frame tabs with clips. Includes -3 AN fittings and adapters to connect them to 3/16" brake line using a 3/8"-24 IFM flare nut.

    • Stainless steel braid over Teflon® hose
    • Reduces volumetric expansion of brake lines
    • Reduces brake fade
    • Less susceptible to debris than rubber line
    • Used to connect from hard line on rear axle to rear calipers when changing from drum to disc brakes

    Kit includes:

    • (2) 8" stainless steel srake lines w/ 7/16" banjo on one end 
    • (2) 7/16" banjo bolts w/ crush washers
    • (2) 3/8" x 24 IFF apapters to the hard lines
    • (2) frame tabs & clips
  • 1963-1966 Chevy 1/2 Ton Pickup Front Disc Brake Conversion Kit
    1963-1966 Chevy 1/2 Ton Pickup Front Disc Brake Conversion Kit
    SKU-91006366
    x
                

    This kit allows you to upgrade your 1963-1966 Chevy pickup to disc brakes and gain the advantage of a more common 5-on-4.75" GM midsize passanger car bolt circle. A wheel change is required, but you want custom 5-lug wheels on your truck anyway, right? The new 11" rotors fit on your stock drum brake spindles.

    Kit includes 11" rotors, GM Midsize calipers, caliper brackets, bearings, seals, spindle nuts, dust caps, banjo bolts, brake hoses, 9" single diaphragm brake booster, master cylinder, disc/drum proportioning valve, and mounting hardware.

    Only for 1/2 ton trucks 

  • Power Brake Booster Conversion Plate
    Power Brake Booster Conversion Plate
    SKU-91031402
    x
                

    If your car currently has manual brakes and you want power brakes, you have to build a new mount for the brake booster. With this plate you will be able to bolt your booster to your existing 2-bolt master cylinder mount.

    Fits boosters with four bolts on 3-3/8" centers. Fits master cylinder mounts with 3-1/4" or 3-3/8" centers.

  • Dual Outlet Master Cylinder Stainless Steel Dual Brake Line Kit
    Dual Outlet Master Cylinder Stainless Steel Dual Brake Line Kit
    SKU-91031802
    x
                

    This is a pair of steel or stainless steel brake lines intended to simplify plumbing from the master cylinder to a proportioning block, such as our 910-31358 or 835-26011179.

    • Features tight 90° bends at the master cylinder end
    • Both ends of both lines are 3/8"-24 inverted flare nuts
    • The longer of the two lines measures app. 12" from the bend to the end
  • Lokar EC-80FUTB T-Bird Emergency Brake Cables, Black Housing
    Lokar EC-80FUTB T-Bird Emergency Brake Cables, Black Housing
    SKU-49108001
    x
                Please view the product's page for more information
            
  • 7/16 Inch-24 IFM to -3 AN Steel Male Brake Adapter Connector Fitting
    7/16 Inch-24 IFM to -3 AN Steel Male Brake Adapter Connector Fitting
    SKU-6174131
    x
                

    Made from high-quality steel, these bulkhead adapters from Speedway give you an easy way to connect lines through firewalls or frames.

    Steel Male Adapter Connector Fitting 

    • AN to IFM all steel adapter
    • 7/16 Inch-24 IFM to -3 AN
  • GM Caliper Slider Bolt
    $2.99
    Product Rating: 4.50 Stars
    GM Caliper Slider Bolt
    SKU-8352300542
    x
                The overall length of these slide bolts is 4-3/8".  The underhead length is 3-3/8".  The thread on the bolts is 7/16-20 (US fine). 
            
  • Lokar XEHB-7000F Floor Mount Emergency Hand Brake, Black Finish
    Lokar XEHB-7000F Floor Mount Emergency Hand Brake, Black Finish
    SKU-49107000
    x
                

    This floor mount emergency hand brake is designed after the automotive industry standard. Lever has been designed with durability in mind and features black powder coated steel construction. Ratchet cut gear plate and lock are heat treated for strength and safety. Special feature includes 4-point mounting capabilities for floor mount or side mounting for personal applications. Comes complete with clevis for installation with Lokar Emergency Brake Cables, Lokar # EC-80FU, Speedway Motors # 491-80FU suggested below.

    Cables are sold separately. E brake handle measures 10" from end-to-end.

    Lokar Install Tip:  Ever think about mounting the floor mount hand brake sideways in front of your seat?  You can!

  • Lokar EFB-9000 Under Dash Emergency Brake Foot Pedal, Brushed Aluminum
    Lokar EFB-9000 Under Dash Emergency Brake Foot Pedal, Brushed Aluminum
    SKU-4919000
    x
                

    Lokar's under-dash emergency brake pedal offers easy operation in a clean, out of the way assembly. Mounted bracket can be adjusted to fit firewall-to-dash distances of 9 to 13 inches.  Pedal arm measures 10 inches and is available with a brushed aluminum or chrome plated finish.

    Under-dash brake pedal works with Connector Cable kit 491-8001HT (which is available in stainless or black) and Universal Cables 491-80FU.

    Under-Dash E-Brake Installation Instructions (PDF)

Goto Previous PagePrevious Page
1 2 3 4 5 ... 25