Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products

Speedway Motors is the classic pickup truck source for body parts, gauges, and interior accessories! Find all the essential fiberglass fenders, hoods, tailgates, gauge sets by Stewart Warner and Auto Meter, and vintage gas caps, in our online catalog. While you are there, check out our emblems and decals, rear and side view mirrors, windshields, fiberglass hoods and step plates. Don't forget about Speedway's vintage seats and seat belts for your classic truck, too!

Featured Products
4 Inch Peep Mirror
$14.99
Product Rating: 4.11 Stars
4 Inch Peep Mirror
x
            Our 4" diameter peep mirror clamps to the top edge of the door. Fits over a door edge that is app. 1/8" thick or thinner. Fits right or left side (reversible). A popular and universal mirror at a low cost. Sold each.
        
Linear Actuator, 12 Volt Motor
Linear Actuator, 12 Volt Motor
x
            

Linear actuators are gear-driven drive motors that extend a shaft with 110 lbs. of force. Our 12V actuators are a universal design for custom installation and operation in countless applications. With built-in limit switches, ACME dive system, and a IP 63 dust and water resistant rating, they are ideal for automotive applications (trunk, hood, doors, etc.) as well as electric wing sliders for Mini Sprints. 

This linear actuator has a potentiometer and can be used with our controller # 910-64295. Available in 4", 6" or 8" strokes.

  • Load Capacity - 110 pounds
  • Static Load - 550 pounds
  • Speed at Max Load - 0.50 in/sec
  • Reccomended Fuse - 10 Amp
  • IP Grade - IP 63-total dust protection, water resistant
  • Pin Holes: 5/16"
  • Retracted Length: 246 mm (9.69")
  • Shaft Diameter: 20 mm (.787")
  • Size: 10-1/4" x 1-1/2" x 3"
  • Weighs approx. 2-3 lbs

Wiring Schematic (GIF)

Universal Seat Sliders
$24.99
Product Rating: 4.42 Stars
Universal Seat Sliders
x
            

These universal seat sliders allow you to easily adjust the bucket seats in your car. Since every application is different, some modification may be required.

Directly fits Speedway seat frame and mounting plates (also available as a complete kit).

910-70026 Instructions (PDF)

Bolt-In 1947-54 Chevy Pickup Mustang II Crossmember
Bolt-In 1947-54 Chevy Pickup Mustang II Crossmember
x
            

Our bolt-in Mustang II suspension kit for 1947-1954 Chevy half-ton and 3/4 ton pickups includes all hardware and instructions. 

  • Completely bolt in - no welding required
  • Based on proven Mustang II geometry
  • Complete with bolt in boxing plates to reinforce the frame
  • Interlocking design for ultimate strength
  • Threaded adjusters to fine tune ride height
  • Full lower A-arms required with this crossmember (strutless type)
  • Requires the use of a power rack and pinion and tubular control arms
  • NOT for use with air ride

910-44754 Instructions (PDF)

Note:  Use bolt-in motor mount kit 910-54754 to mount your S/B Chevy.

"Classic Truck, Body" Page 1 of 25

  • Sill Weather Whisker Strip
    $29.99
    Sill Weather Whisker Strip
    x
                After putting in new glass and window felt run channels, you don't want to reuse your old whisker that's on your garnish moldings, so here's a way to prevent scratching up that new glass. We now offer a 48" long, 9/16" tall whisker strip. Only offered in black.
            
  • Universal Expanding Body Mounts
    Universal Expanding Body Mounts
    x
                

    If you are building a lightweight car like a "T" or an "A", mounting the body may present a problem. These neat expanding rubber universal body mounts allow you to drill a 3/4" hole in the top of the frame, insert a 3/8" coarse bolt, tighten, then the body is mounted.

    Not recommended for cars newer than 1934.

  • Hidden Tail Gate Latch w/ 21 Inch Straps
    Hidden Tail Gate Latch w/ 21 Inch Straps
    x
                

    The last thing you want on your tricked-out classic truck are beat-up old tailgate latches and rusty tailgate chains. This clean latch setup uses small stainless steel brackets that attach to the tailgate, stainless catch assemblies with spring-loaded nylon buttons that install in the bed sides, and woven nylon check straps to hold your tailgate open without damaging that expensive paint job. It's an easy-to-install system that works as nice as it looks and wont rust or rattle.

    910-00021 Instructions (PDF)

  • 1964-66 Chevy Pickup Switch Panel Cover
    1964-66 Chevy Pickup Switch Panel Cover
    x
                

    These billet aluminum switch panel covers are made to fit your 1964-1966 Chevy pickup truck dash.  They are designed to fit in place of your switches for a new styled sleek look.

    • Billet aluminum
    • 1964-1966 Chevy Pickup
    • Switch eliminator panel
  • 1935-37 Ford Pickup Rear Fender Filler Panel
    1935-37 Ford Pickup Rear Fender Filler Panel
    x
                
            
  • Rubber GM Transmission Cushion
    Rubber GM Transmission Cushion
    x
                

    OEM-style rubber transmission cushion for many '58-'82 GM transmissions including TH350 auto, Muncie, Saginaw, and others.

    • Meets or exceeds OEM specifications 
    • Rubber formulation provides abrasion resistance and aging stability
    • Tough, hardened steel plate & inserts
    • Chemlock® bonding agent ensures superior rubber-to-metal bond
  • Speedway 5 Gauge Set
    $159.99
    Speedway 5 Gauge Set
    x
                
    • Stainless steel bezel
    • Backlit white face
    • Includes:
      • 3-3/8” Mechanical Speedometer       
      • 2-1/16” gauges
    • Mechanical oil pressure gauge and line kit
    • Voltmeter
    • Mechanical water temp gauge
    • Fuel gauge and sender
  • Base Door Panel Kit
    $149.99
    Base Door Panel Kit
    x
                Design your own custom door panel with Hagan panel components. This kit comes with 4 black panel boards that are 39" x 32" which include 50 inline panel clips and a How-To video. Base boards are made of dense 1/8" water-resistant cardboard.
            
  • Extension For Peep Mirror
    $19.99
    Product Rating: 3.67 Stars
    Extension For Peep Mirror
    x
                

    You want peep mirrors, but they are too short? With this 1-1/2" longer extension, that problem has gone away. Chrome plated to match the peep mirror and machined to fit at both ends. 

    Mirror not included.

  • Linear Actuator Aluminum Mounting Bracket, 1-1/2 x 1-1/2 Inch
    Linear Actuator Aluminum Mounting Bracket, 1-1/2 x 1-1/2 Inch
    x
                

    These billet aluminum mounting brackets are for our Linear Actuator 910-64290. They are designed to mount your linear actuators to hoods, trunks, etc. on either flat or angled surfaces. Solid aluminum construction provides the greatest strength possible while remaining a great looking piece. The brackets are a satin finish, but can be polished to a bright shine.  Sold individually - you may need two mounts (one for each end of the actuator).  Includes bracket and three securing screws.

    • Billet aluminum
    • Satin finish
    • Mount linear actuators to hoods, trunks, etc.
    • Mount to either flat or angled surfaces
    • Sold individually - may need one mount for each end
    • Works with Linear Actuator 910-64290
    • Includes bracket and three securing screws

    NOTE: The vendor no longer includes the mounting plate as pictured in previous catalogs.

  • Tubular Transmission Mount with 2 Inch Drop
    Tubular Transmission Mount with 2 Inch Drop
    x
                

    Universal rear transmission mounts and heavy duty tube crossmember. Fit most GM, Ford, and Mopar manual and auto transmissions. Black powder coated finish. Crossmember must be welded directly into frame or to 3 hole mounting flanges for bolt-in application. Fits frames up to 38" wide.

     

    Note: May require re-drilling of the mount holes when used with Ford C4/C6 trans cushion 910-18017.

  • DEi 050501 Floor and Tunnel Shield II, Heat and Sound Insulation, 2 Ft. x 21 Inch
    DEi 050501 Floor and Tunnel Shield II, Heat and Sound Insulation, 2 Ft. x 21 Inch
    x
                

    Designed to provide the best possible heat protection in areas where high temperatures are always present and problematic, Floor & Tunnel Shield II limits heat transfer on fire walls, transmission tunnels, floor boards, fuel cells and other areas where heat is an issue.  Floor & Tunnel Shield II provides excellent light weight thermal protection, acts as a guard against track and road debris, and provides sound deadening as well.

    Constructed with an embossed 10 mil aluminum face bonded to 1/8” composite glass-fiber core and backed with a high temp super strong pressure sensitive backing, Floor & Tunnel Shield II withstands up to 1750°F of direct continuous heat. The adhesive side holds past 450°F. Its improved multifaceted modern aluminum surface offers improved reflectivity and rigidity and allows for ease of installation. At only 3/16” thick, this product can be shaped and trimmed for a custom fit and is ideal for minimal clearance areas.

    With a unique and patented finely woven glass-fiber backing, Floor & Tunnel Shield II is the easiest, most cost effective way to control thermal transfer while protecting expensive components and vehicle occupants from extreme heat situations and sound.

    Floor & Tunnel Shield II can be used on any number of surfaces including, metal, aluminum, carbon fiber, plastic, and more. Multiple uses include: fire walls, under hoods, transmission tunnels, fl

  • Auto Meter 3357 Transmission Temperature Gauge
    Auto Meter 3357 Transmission Temperature Gauge
    x
                

    Sport Comp temperature gauge features air-core meter movement with a 2-1/16" O.D. Temperature meter includes 1/8" NPT sender with 3/8" NPT and 1/2" NPT adapter fittings.

    If mounting temperature sender in a steel pan, use bung 617-6701. Aluminum pans use bung 617-6801.

  • Adjustable Seat Riser
    $39.99
    Adjustable Seat Riser
    x
                
    • Cadmium plated steel
    • Sold in pairs
    • Three mounting hole options to adjust height
  • Stewart Warner 82310 Deluxe Ammeter Gauge, 2-1/16 Inch, 30-0-30 Amps
    Stewart Warner 82310 Deluxe Ammeter Gauge, 2-1/16 Inch, 30-0-30 Amps
    x
                Stewart Warner Deluxe 2-1⁄16" diameter ammeter gauges feature a black face, white letters and chrome bezel. A 12 volt light is included.
            
  • 1964-66 Chevy Pickup Billet Glove Box Cover
    1964-66 Chevy Pickup Billet Glove Box Cover
    x
                Billet aluminum glove box cover for 1964-1966 Chevy pickup trucks. Machined from 1/8" thick aluminum and mounts onto the glove box door using glue or tape.
            
  • Auto Meter 2268 LS Series Oil Pressure Sender Adapter
    Auto Meter 2268 LS Series Oil Pressure Sender Adapter
    x
                

    This LS Series oil pressure sender fitting allows your aftermarket 1/8" NPT oil pressure sending unit to be installed in place of the OEM oil pressure sender.

    When installing aftermarket gauges, the OEM oil pressure sender is not required by the PCM and may be replaced by the aftermarket sender of your choice.

  • Glass Run Channel
    $24.99
    Product Rating: 5.00 Stars
    Glass Run Channel
    x
                This is a highly flexible U-shaped channel comes in an 8-foot-long x 5/8" wide coil with sides that are 9/16" tall. You will need one coil of window felt per door.
            
  • 4 Inch Peep Mirror
    $14.99
    Product Rating: 4.11 Stars
    4 Inch Peep Mirror
    x
                Our 4" diameter peep mirror clamps to the top edge of the door. Fits over a door edge that is app. 1/8" thick or thinner. Fits right or left side (reversible). A popular and universal mirror at a low cost. Sold each.
            
  • Ididit 2503000040 Universal Billet Aluminum Knob, 3/16 Inch Bore
    Ididit 2503000040 Universal Billet Aluminum Knob, 3/16 Inch Bore
    x
                

    Universal billet aluminum switch knobs work great as a headlight switch knob, dash knob, door knobs, lock knob, wiper knob, or a radio knob. These 3/16" versions are retained with a set screw.

  • Wilwood Reverse Swing Triple Master Cylinder Pedal, 6.2:1
    Wilwood Reverse Swing Triple Master Cylinder Pedal, 6.2:1
    x
                

    Wilwood's racing brake/clutch pedal assemblies are the result of years of hands-on experience, input from racers and chassis builders, and design, material selection and manufacturing techniques that result in durable, lightweight components. They incorporate ergonomics without sacrificing performance, and practical requirements without adding weight.

    Tri reverse mount master cylinder pedal assembly has both clutch and brake pedals with balance bar for dual brake master cylinders.

    • Combines the brake & clutch pedals into one unit
    • Positions M/C inside the firewall away from engine heat
    • Aluminum frame & arm construction
    • Steel pivots & mounting studs
    • Anti-skid pedal pads
    • Clevis and pivot pin balance bar provide smooth and accurate settings of the brake pedal bias
    • Bias can be set and locked down with the jam nut, or attached to a remote cable for quick on-track adjustment

    910-29974 Instructions (PDF)

    Learn more about selecting the proper master cylinder for your vehicle by reading our tech article. Brake System Selection. 

  • Stewart Warner 82492 Wings Boost Gauge, Black
    Stewart Warner 82492 Wings Boost Gauge, Black
    x
                

    Bright chrome bezels, curved glass lenses, teardrop pointers and the distinctive "Wings" logo make these gauges right at home in any dash. Their rugged construction gives unsurpassed performance, readability and crisp, accurate response.

    • Classic 1940s retro styling 
    • 2-1/16" diameter
    • Mechanical operation
    • 12-volt lamp
    • Choice of black or white face
  • Stewart Warner 82328 Deluxe Vacuum Gauge, Mechanical, 2-1/16 Inch
    Stewart Warner 82328 Deluxe Vacuum Gauge, Mechanical, 2-1/16 Inch
    x
                

    Stewart Warner Deluxe Series gauges feature black faces with white lettering, polished stainless steel bezels and 12 volt back lighting for night time visibility.

    Requires tubing kit 665-82553 listed.

  • Body Savers, .433 Inch Hole, 10/Bag
    Body Savers, .433 Inch Hole, 10/Bag
    x
                
    • Extend the life of your fiberglass body parts by eliminating ovaling
    • Mount using 1/8" rivets
    • 430 Stainless steel 
    • .433" diameter
    • Pack of 10
  • Replacement Lap Seat Belts
    $14.99
    Product Rating: 4.50 Stars
    Replacement Lap Seat Belts
    x
                Before you floor it...BUCKLE UP! These replacement seat belts will allow you to upgrade your car to a modern lap seat belt. Handy push button buckle is attached to 1-7/8" wide belt. This seatbelt allows the mounting tabs to be installed at different distances from the buckle and still allows the buckle to be positioned at a place (over the wearers' midsection) of the installers' choosing. 74" long to fit most applications. Black.

    Meets DOT and federal standards.

    910-72050 Instructions (PDF)

  • Gauge Replacement Light Bulb Kit
    Gauge Replacement Light Bulb Kit
    x
                Kit includes bulb, wire and socket. This fits a 5/8" light hole.
            
  • BedWood Wood Kit for 1947-51 1st Series Chevy 3100 SWB Stepside Pickup
    BedWood Wood Kit for 1947-51 1st Series Chevy 3100 SWB Stepside Pickup
    x
                

    These premier show quality BedWood kits are precision milled to 3/4" thick, properly grooved, trimmed to length, sanded and ready to finish! Made in Kentucky, U.S.A. 

    • Bed Wood - Non-Drilled
    • Designed for 1947-51 First Series Chevy 3100 SWB Stepside 
    • Made in Kentucky, U.S.A.
    • Choice of Red Oak, White Oak, or Walnut
    • Precision milled to 3/4" thick
    • Bed Size: 76-7/8" Length x 50" Width
    • Board Qty: 9
    • Bed Strip Qty Needed: 8

    Be sure to add your choice of two styles of extruded aluminum strip kits (includes hidden fasteners).

  • HushMat Ultra Floor/Dash Kit-Thermal & Sound Insulation
    HushMat Ultra Floor/Dash Kit-Thermal & Sound Insulation
    x
                Please view the product's page for more information
            
  • Auto Meter 2301 3-3/4 Inch 8000 RPM Tach, Chrome
    Auto Meter 2301 3-3/4 Inch 8000 RPM Tach, Chrome
    x
                

    These 3-3/4" diameter Autogage Series tachs by Auto Meter have a 8000 RPM range and include a backlight. Also includes a pedestal mount which can be mouted to your steering column or any flat surface. Operates on 4, 6, or 8 cylinder engines with points, electronic, and most 12V high performance racing ignitions. 

    Auto Meter Tach Application Chart (GIF)

    Tach Wiring Guide (GIF)

    3-3/4" Tachometer Installation Instructions (PDF)

  • Under Dash 2-Hole Mounting Panels
    Under Dash 2-Hole Mounting Panels
    x
                    Beautifully chrome plated panel to make installation of 2-1/16" or  2-1/8" gauges under your dash a snap.         
            
  • 1948-1952 Ford Pickup Glove Box Liner
    1948-1952 Ford Pickup Glove Box Liner
    x
                

    These glove box liners are stamped out of a waterproof cardboard and replicate the originals.  They are designed to fit 1948-1952 Ford pickup trucks and come with all necessary mounting hardware.

    • Stamped out of a waterproof cardboard
    • Replicate the original
    • 1948-1952 Ford pickups
    • Includes mounting hardware
  • Longacre 50888 Air Density Gauge
    Longacre 50888 Air Density Gauge
    x
                

    Get precise carb jetting every race! This gauge from Longacre helps you set air/fuel ratios to compensate for changes in barometric pressure and air temperature. As air density changes with weather conditions, you should rejet your carb to keep to horsepower and sharp response.

    Comes complete with case and jetting chart. 2-1/4" gauge face, 2-7/8" bezel O.D.

    Cannot ship by air.

    Air Density Gauge Installation Instructions

  • Clip-In Conversion Kit
    $19.99
    Product Rating: 4.00 Stars
    Clip-In Conversion Kit
    x
                

    Convert your harness from bolt-in to clip-in with this kit. All heavy duty hardware and snap hook. Two bolts, two washers, two clips.

    • Shank diameter is .434 or 7/16 X 20 threads per inch
    • Shank thread length is approximately 1 5/8"
    • Overall length including the eye is 3 1/8"
    • Washer diameter is 2 1/2" with 7/16" hole
    • Fits 2 inch wide belts

     

  • Speedway Universal 20 Circuit Wiring Harness
    Speedway Universal 20 Circuit Wiring Harness
    x
                Whether you're building an option loaded car or just want to have extra circuits available for future updates, this harness is perfect and makes any job painless. Compact 5-1/2"L x 4-1/2"W x 3-1/4"H  fuse block holds 18 standard push-in fuses and can be mounted almost anywhere. 

    Each high temperature wire is color coded and labeled every six inches. Also includes GM type steering column connectors. To keep costs down and the quality high, this harness does not include any switches, light sockets or plugs that you would normally already have.

    • Harness has 20 circuits, of which 18 are fused
    • Taillight leads measure 17' long
    • Includes plug for GM column, headlight switch, dimmer switch, and signal flashers

    Wiring Harness Installation Instructions (PDF)

  • Small Block Ford Crossmember Motor Mount
    Small Block Ford Crossmember Motor Mount
    x
                Universal mount allows 260-289-302-351W S/B Fords and 1970-1974 Cleveland engines with front sump oil pan to be installed into most frames up to 38" wide. Cut for frame width, then bolt or weld in.   

    Note: We've found a lot of variation in width of Ford blocks. Bolt the cushion to the block first to get proper width measurement. Mounts are not returnable once they've been altered or installed!

  • Ford Script Step Plate
    $54.99
    Product Rating: 4.00 Stars
    Ford Script Step Plate
    x
                Polished aluminum diamond style step plate with 'Ford' logo. 

    Any reference to the names Ford, Chevy, Mopar, Dodge, Plymouth - or any other car manufacturer is for fit, application and reference only!  In no way are we implying the part was manufactured by any car manufacturer.

  • Speedway Liquid Filled Fuel Pressure Gauge
    Speedway Liquid Filled Fuel Pressure Gauge
    x
                

    High quality, liquid-filled stainless steel fuel pressue gauge for remote mounting.

    • 0-15 psi
    • 1-3/4" face
    • 1/8" NPT connection

    910-11852 Instructions (PDF)

  • Stainless Steel Pickup Bed Strips
    Stainless Steel Pickup Bed Strips
    x
                

    Clean up the bed of your pickup with these smooth, highly polished stainless steel strips which use sliding T-bolt fasteners (sold separately) to eliminate the stock-style carriage bolts. Each universal set comes with seven strips that are 82" long x 1-1/2" wide.

    910-00100 Instructions (PDF)

  • Chrome Skull License Plate Bolts
    Chrome Skull License Plate Bolts
    x
                

    Are you looking for a way to top off those fresh new plates? If so, then these chrome skull license plate bolts are right up your alley. They include steel washers, nuts, and bolts to keep your plates securely in place.

    • Steel washers, nuts, and bolts 
    • Sold as a pair of two(2)
    • Chrome finish
  • Engine Turned Aluminum Panels
    From: $34.99
    Product Rating: 4.63 Stars
    Engine Turned Aluminum Panels
    x
                You can now give your car the look you have been looking for with our engine turned aluminum panels.  These 0.063" thick aluminum panels are 6" wide and feature 1/2" swirls.
            
Goto Previous PagePrevious Page
1 2 3 4 5 ... 25