Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Air and Fuel Delivery At Speedway Motors

Getting the right mix of fuel and oxygen into your engine can be tricky. Our award winning Techs can help set up a race-winning fuel system that makes serious power, but is reliable enough for your daily driver. From air cleaners to superchargers, Speedway Motors wants to help makes sure you never starve your engine again!

"Carburetion, Accelerator Linkage Rod Connectors" Page 1 of 1

Garage Sale (0)

  • Carb Linkage Thread End for 9 Super 7   /Stromberg 97/Demon 98 Carbs, RH
    Carb Linkage Thread End for 9 Super 7 /Stromberg 97/Demon 98 Carbs, RH
    x
                

    This carb linkage rod end has 3/16" fine RH threads (also known as 10-32).  It is intended for use with 9 Super 7 ®, Stromberg 97, and Demon 98 carburators.

    • 3/16" fine RH threads (10-32)
    • Secures with pin
    • Steel
    • .430" Diameter
    • Application:
      • 9 Super 7 ®
      • Stromberg 97
      • Demon 98
  • Carb Linkage Thread End for 9 Super 7   /Stromberg 97/Demon 98 Carbs, LH
    Carb Linkage Thread End for 9 Super 7 /Stromberg 97/Demon 98 Carbs, LH
    x
                

    This carb linkage rod end has 3/16" fine LH threads (also known as 10-32).  It is intended for use with 9 Super 7 ®, Stromberg 97, and Demon 98 carburators.

    • 3/16" fine LH threads (10-32)
    • Secures with pin
    • Steel
    • .430" Diameter
    • Application:
      • 9 Super 7 ®
      • Stromberg 97
      • Demon 98

     

  • 3-Carb Progressive Throttle Linkage
    3-Carb Progressive Throttle Linkage
    x
                

    Three-carb progressive linkage for Ford/Holley 94's and Stromberg 97's. It can be modified to work with other 2G Rochester applications, however the arms must be drilled for the larger diameter shafts.

    Maximum center to center of long shaft is 11-3/8" and maximum of short shaft is 7". Linkage can be used for either two 2 bbl or three 2 bbl applications.

    560-6271 Instructions (PDF) 

  • Aluminum Adjustable Throttle Linkage Rod
    Aluminum Adjustable Throttle Linkage Rod
    x
                

    Accelerator linkage rod is 25-1/2" long with 1/4" rod ends.

    • 25-1/2" long "hex" aluminum
    • 1/4" male rod ends
    • Anodized purple

     

  • Lokar S-68156 5/16-24 Inch Thread Rod End w/Nut, Pair
    New
    Lokar S-68156 5/16-24 Inch Thread Rod End w/Nut, Pair
    x
                
    • Rod Ends
    • Made In The U.S.A.
    • Lifetime Warranty
  • Lokar XTCB-PLR3 Midnight Series Linkage, Holley Carb, 8-1/4 - 8-5/8
    New
    Lokar XTCB-PLR3 Midnight Series Linkage, Holley Carb, 8-1/4 - 8-5/8
    x
                
    • Progressive Linkage for in-line dual carburetors
    • Design allows the use of only one carb during normal driving conditions and both carburetors at wide open throttle
    • Available in Midnight Series™
  • AFCO 10175-18 Throttle Linkage Rod Kit, 18 Inch
    AFCO 10175-18 Throttle Linkage Rod Kit, 18 Inch
    x
                
    Adjustable throttle linkage rod kit includes 1/4" plated steel rod with right hand 1/4" male threads on both ends. Kit also includes carb bushings with 1/4" female rod ends, jam nuts and rod.
    • 1/4" plated steel rod w/ r/h 1/4" male threads on both ends
    • Includes carb bushings, 1/4" female rod ends, jam nuts, & rod
    Note: Extra-long thread allows more adjustment
  • Edelbrock 6 Carb Throttle Linkage Kit for GM Ram Log Intake, 94 Type Carbs
    Edelbrock 6 Carb Throttle Linkage Kit for GM Ram Log Intake, 94 Type Carbs
    x
                

    This linkage is for an Edelbrock Ram Log intake with 6 "94" carbs on a 325-2150 intake. They feature progressive throttle blade action and include all necessary hardware and instructions for installation.

    • Designed for use on Edelbrock X1 Ram Log intake manifolds
    • Applicable to Edelbrock/Holley "94" carburetors only
    • 6-carb linkage kits
    • Originally designed by Vic Edelbrock Sr. for smooth carburetor operation

  • Lokar 1010148 Rod Type Throttle Linkage Kit, 4 Hole Plenum, Black
    New
    Lokar 1010148 Rod Type Throttle Linkage Kit, 4 Hole Plenum, Black
    x
                Lokar Shifter and Hand Brake Boots are black Naugahyde and all sets include a boot, polished stainless base ring, or billet aluminum ring with ball-milled edge and stainless screws. 
    • Our Classic Shifter Boot is designed with a polished stainless bezel on top of the boot which fits over the shifter lever.
    • It also includes a foam rubber seal to eliminate air flow from the floor through the boot.
    • All boots hug the shifter lever and there are no unsightly pull ties or laces.
  • Lokar XTCB-PLR1 Midnight Series Linkage, Edelbrock Carb, 6-3/8 - 6-3/4
    New
    Lokar XTCB-PLR1 Midnight Series Linkage, Edelbrock Carb, 6-3/8 - 6-3/4
    x
                
    • Progressive Linkage for in-line dual carburetors
    • Design allows the use of only one carb during normal driving conditions and both carburetors at wide open throttle
    • Available in Midnight Series™
  • Edelbrock 1032 94 Carb Throttle Linkage Rod Kit, Dual Carb, Standard
    Edelbrock 1032 94 Carb Throttle Linkage Rod Kit, Dual Carb, Standard
    x
                These standard Edelbrock throttle linkage kits are a non progressive adjustable throttle linkage rod for Edelbrock 94 carburetors. They are available for dual and triple carburetor set-ups. Edelbrock 94 carburetors are equipped with an extended length throttle shaft, making these kits a bolt-on to Edelbrock 94 carbs.
            
  • Lokar XTCB-PLR2 Midnight Series Linkage, Edelbrock Carb, 8-5/8- 9 Inch
    New
    Lokar XTCB-PLR2 Midnight Series Linkage, Edelbrock Carb, 8-5/8- 9 Inch
    x
                
    • Progressive Linkage for in-line dual carburetors
    • Design allows the use of only one carb during normal driving conditions and both carburetors at wide open throttle
    • Available in Midnight Series™
  • Lokar XTCB-40DQ1 Midnight Series Edelbrock Progressive Carb Linkage
    New
    Lokar XTCB-40DQ1 Midnight Series Edelbrock Progressive Carb Linkage
    x
                For in-line dual carburetors. Allows for use of one carburetor during normal driving and both carburetors at wide open throttle. Made in the U.S.A. Lifetime warranty.
    • Strength And Style
    • Designed To Fit Single Or Dual Quad Cabs
    • Easy Installation
    • Dual Stainless Steel Return Springs
    • All Hardware And Detailed Instructions Incl.
    • Eliminates Bracket Movement
  • Lokar S-68155 1/4-28 Inch Thread Rod End w/Nut, Pair
    New
    Lokar S-68155 1/4-28 Inch Thread Rod End w/Nut, Pair
    x
                
    • Rod Ends
    • Made In The U.S.A.
    • Lifetime Warranty
  • Lokar 1010141 Rod Type Throttle Linkage Kit, 4 Hole Plenum, Blue
    New
    Lokar 1010141 Rod Type Throttle Linkage Kit, 4 Hole Plenum, Blue
    x
                Lokar Shifter and Hand Brake Boots are black Naugahyde and all sets include a boot, polished stainless base ring, or billet aluminum ring with ball-milled edge and stainless screws. 
    • Our Classic Shifter Boot is designed with a polished stainless bezel on top of the boot which fits over the shifter lever.
    • It also includes a foam rubber seal to eliminate air flow from the floor through the boot.
    • All boots hug the shifter lever and there are no unsightly pull ties or laces.
  • Weiand 7166 Supercharger Carburetor Linkage Kit
    Weiand 7166 Supercharger Carburetor Linkage Kit
    x
                

    Carburetor linkage for use with side mounted 4V carburetors (6-71 & 8-71 Series). Constructed of high quality rod ends, stainless steel shafts, and black anodized aluminum supports to make hooking up your carburetors a snap.

    805-7166 Instruction Sheet (PDF)

  • Lokar TCB-PLR3 Holley Carb Progressive Linkage Kit on 8-1/4 - 8-5/8
    Lokar TCB-PLR3 Holley Carb Progressive Linkage Kit on 8-1/4 - 8-5/8
    x
                

    This linkage kit allows you to drive around on just one 4 barrel unless you mash it. Unique linkage is adjustable and is inline for dual quads only.

     

  • Edelbrock 1159 94 Carburetor Ball-End Stud Arm
    Edelbrock 1159 94 Carburetor Ball-End Stud Arm
    x
                This part is a bolt on throttle ball that is designed to be used only in conjunction with the Edelbrock 94 carb, part number 3251151. This part bolts to the passenger side of the carburetor, and allows the use of the OEM ball and socket style throttle linkage.
            
  • Edelbrock 1034 94 Carb Throttle Linkage Rod Kit, Triple Carb, Standard
    Edelbrock 1034 94 Carb Throttle Linkage Rod Kit, Triple Carb, Standard
    x
                These Edelbrock throttle linkage rod kits are a non progressive adjustable throttle linkage rod for Edelbrock 94 carburetors. They are available for dual and triple carburetor set-ups. Edelbrock 94 carburetors are equipped with an extended length throttle shaft, making these kits a bolt-on to Edelbrock 94 carbs.
            
  • Lokar TCB-PLR1 Edelbrock Carb Progressive Linkage Kit, 6-3/8 - 6-3/4
    Lokar TCB-PLR1 Edelbrock Carb Progressive Linkage Kit, 6-3/8 - 6-3/4
    x
                

    This linkage kit allows you to drive around on just one 4 barrel unless you mash it. Unique linkage is adjustable and is inline for dual quads only.

     

  • Single End Carburetor Linkage Rod, 7 Inches Long
    Single End Carburetor Linkage Rod, 7 Inches Long
    x
                

    3/16" steel throttle rod carburetor linkage with a single end. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • Single End Carburetor Linkage Rod, 3-1/2 Inches Long
    Single End Carburetor Linkage Rod, 3-1/2 Inches Long
    x
                

    3/16" steel throttle rod carburetor linkage with a single end. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • Double End Carburetor Linkage, 3 Inches Long, Non-Adjustable
    Double End Carburetor Linkage, 3 Inches Long, Non-Adjustable
    x
                

    This 3" long, double-end carb linkage is constructed from 3/16" steel rod. Non-adjustable design. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • Henchcraft Chassis Mini Lightning Sprint Throttle Linkage Rod
    New
    Henchcraft Chassis Mini Lightning Sprint Throttle Linkage Rod
    x
                

    New from Henchcraft Chassis, these throttle linkage rods are designed for use with Mini Lightning Sprint chassis.  9" throttle rod with bend for clearance. Mates to proprietary bell crank for smooth operation. Threaded ends for male rod ends.

    • Throttle linkage rod only
    • Will not allow throttle to stick
    • Return springs can be added to fit driver preference
    • For use on Henchcraft Mini Lightning Sprint chassis
  • Lokar 1010142 Rod Type Throttle Linkage Kit, 4 Hole Plenum, Red
    New
    Lokar 1010142 Rod Type Throttle Linkage Kit, 4 Hole Plenum, Red
    x
                Lokar Shifter and Hand Brake Boots are black Naugahyde and all sets include a boot, polished stainless base ring, or billet aluminum ring with ball-milled edge and stainless screws. 
    • Our Classic Shifter Boot is designed with a polished stainless bezel on top of the boot which fits over the shifter lever.
    • It also includes a foam rubber seal to eliminate air flow from the floor through the boot.
    • All boots hug the shifter lever and there are no unsightly pull ties or laces.
  • Moroso 65444 1:1 Slip Linkage Kit for 4150 Holley
    Moroso 65444 1:1 Slip Linkage Kit for 4150 Holley
    x
                These slip links for Holley 4150 carbs are designed to replace the "progressive" stock link to provide simultaneous, 1:1 primary and secondary opening rates.
    • Replaces "progressive" stock link
    • 1:1 primary and secondary opening rates
    • Requires drilling of existing primary throttle arm hole
    • One per package

    54565444 Instructions (PDF)

  • Edelbrock 1033 94 Triple Carb Throttle Linkage Rod Kit, Progressive
    Edelbrock 1033 94 Triple Carb Throttle Linkage Rod Kit, Progressive
    x
                

    The progressive design operates a single or two carburetors to part throttle before synchronizing all three carbutetors to open fully at wide open throttle.  Edelbrock 94 carburetors are equipped with an extended length throttle shaft, making these kits a bolt-on to Edelbrock 94 carbs.

    • Operates a single or dual carb to half throttle and pregresses all three to WOT
    • Saves fuel, provides smoother throttle operation and ends flat spots
  • Single End Carburetor Linkage Rod, 9 Inches Long
    Single End Carburetor Linkage Rod, 9 Inches Long
    x
                

    3/16" steel throttle rod carburetor linkage with a single end. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.