Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products

Getting the right mix of fuel and oxygen into your engine can be tricky. Our award winning Techs can help set up a race-winning fuel system that makes serious power, but is reliable enough for your daily driver. From air cleaners to superchargers, Speedway Motors wants to help makes sure you never starve your engine again!

"Carburetion, Accelerator Linkage Rod Connectors" Page 1 of 1

  • Carb Linkage Thread End for 9 Super 7   /Stromberg 97/Demon 98 Carbs, RH
    Carb Linkage Thread End for 9 Super 7 /Stromberg 97/Demon 98 Carbs, RH
    x
                

    This carb linkage rod end has 3/16" fine RH threads (also known as 10-32).  It is intended for use with 9 Super 7 ®, Stromberg 97, and Demon 98 carburators.

    • 3/16" fine RH threads (10-32)
    • Secures with pin
    • Steel
    • .430" Diameter
    • Application:
      • 9 Super 7 ®
      • Stromberg 97
      • Demon 98
  • Carb Linkage Thread End for 9 Super 7   /Stromberg 97/Demon 98 Carbs, LH
    Carb Linkage Thread End for 9 Super 7 /Stromberg 97/Demon 98 Carbs, LH
    x
                

    This carb linkage rod end has 3/16" fine LH threads (also known as 10-32).  It is intended for use with 9 Super 7 ®, Stromberg 97, and Demon 98 carburators.

    • 3/16" fine LH threads (10-32)
    • Secures with pin
    • Steel
    • .430" Diameter
    • Application:
      • 9 Super 7 ®
      • Stromberg 97
      • Demon 98

     

  • 3-Carb Progressive Throttle Linkage
    3-Carb Progressive Throttle Linkage
    x
                

    Three-carb progressive linkage for Ford/Holley 94's and Stromberg 97's. It can be modified to work with other 2G Rochester applications, however the arms must be drilled for the larger diameter shafts.

    Maximum center to center of long shaft is 11-3/8" and maximum of short shaft is 7". Linkage can be used for either two 2 bbl or three 2 bbl applications.

    560-6271 Instructions (PDF) 

  • Aluminum Adjustable Throttle Linkage Rod
    Aluminum Adjustable Throttle Linkage Rod
    x
                

    Accelerator linkage rod is 25-1/2" long with 1/4" rod ends.

    • 25-1/2" long "hex" aluminum
    • 1/4" male rod ends
    • Anodized purple

     

  • Garage Sale - Edelbrock 94 Carb Throttle Linkage kit, Dual Carb, Standard
    Garage Sale
    Garage Sale - Edelbrock 94 Carb Throttle Linkage kit, Dual Carb, Standard
    x
                

    These Edelbrock throttle linkage kits are a non progressive adjustable linkage for Edelbrock 94 carburetors. They are available for dual and triple carburetor set-ups. Edelbrock 94 carburetors are equipped with an extended length throttle shaft, making these kits a bolt-on to Edelbrock 94 carbs.

     

    This linkage is garage sale priced because it has been test fit and returned. 

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS 

  • AFCO 10175-18 Throttle Linkage Rod Kit, 18 Inch
    AFCO 10175-18 Throttle Linkage Rod Kit, 18 Inch
    x
                
    Adjustable throttle linkage rod kit includes 1/4" plated steel rod with right hand 1/4" male threads on both ends. Kit also includes carb bushings with 1/4" female rod ends, jam nuts and rod.
    • 1/4" plated steel rod w/ r/h 1/4" male threads on both ends
    • Includes carb bushings, 1/4" female rod ends, jam nuts, & rod
    Note: Extra-long thread allows more adjustment
  • Edelbrock 6 Carb Throttle Linkage Kit for GM Ram Log Intake, 94 Type Carbs
    Edelbrock 6 Carb Throttle Linkage Kit for GM Ram Log Intake, 94 Type Carbs
    x
                

    This linkage is for an Edelbrock Ram Log intake with 6 "94" carbs on a 325-2150 intake. They feature progressive throttle blade action and include all necessary hardware and instructions for installation.

    • Designed for use on Edelbrock X1 Ram Log intake manifolds
    • Applicable to Edelbrock/Holley "94" carburetors only
    • 6-carb linkage kits
    • Originally designed by Vic Edelbrock Sr. for smooth carburetor operation

  • Garage Sale - 3-Carburetor Linkage
    $34.99
    $49.99
    Garage Sale
    Garage Sale - 3-Carburetor Linkage
    x
                

    This item is garage sale priced because it was used on a display.

     

    **NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS**

     

    Triple carb linkage.  Stainless steel shafts.  Longer shaft is 12" long, two shorter shafts are each 4-1/2" long.

     

     

  • Edelbrock 1032 94 Carb Throttle Linkage Rod Kit, Dual Carb, Standard
    Edelbrock 1032 94 Carb Throttle Linkage Rod Kit, Dual Carb, Standard
    x
                These standard Edelbrock throttle linkage kits are a non progressive adjustable throttle linkage rod for Edelbrock 94 carburetors. They are available for dual and triple carburetor set-ups. Edelbrock 94 carburetors are equipped with an extended length throttle shaft, making these kits a bolt-on to Edelbrock 94 carbs.
            
  • Weiand 7166 Supercharger Carburetor Linkage Kit
    Weiand 7166 Supercharger Carburetor Linkage Kit
    x
                

    Carburetor linkage for use with side mounted 4V carburetors (6-71 & 8-71 Series). Constructed of high quality rod ends, stainless steel shafts, and black anodized aluminum supports to make hooking up your carburetors a snap.

    805-7166 Instruction Sheet (PDF)

  • Lokar TCB-PLR3 Holley Carb Progressive Linkage Kit on 8-1/4 - 8-5/8
    Lokar TCB-PLR3 Holley Carb Progressive Linkage Kit on 8-1/4 - 8-5/8
    x
                

    This linkage kit allows you to drive around on just one 4 barrel unless you mash it. Unique linkage is adjustable and is inline for dual quads only.

     

  • Edelbrock 1159 94 Carburetor Ball-End Stud Arm
    Edelbrock 1159 94 Carburetor Ball-End Stud Arm
    x
                This part is a bolt on throttle ball that is designed to be used only in conjunction with the Edelbrock 94 carb, part number 3251151. This part bolts to the passenger side of the carburetor, and allows the use of the OEM ball and socket style throttle linkage.
            
  • Edelbrock 1034 94 Carb Throttle Linkage Rod Kit, Triple Carb, Standard
    Edelbrock 1034 94 Carb Throttle Linkage Rod Kit, Triple Carb, Standard
    x
                These Edelbrock throttle linkage rod kits are a non progressive adjustable throttle linkage rod for Edelbrock 94 carburetors. They are available for dual and triple carburetor set-ups. Edelbrock 94 carburetors are equipped with an extended length throttle shaft, making these kits a bolt-on to Edelbrock 94 carbs.
            
  • Lokar TCB-PLR1 Edelbrock Carb Progressive Linkage Kit, 6-3/8 - 6-3/4
    Lokar TCB-PLR1 Edelbrock Carb Progressive Linkage Kit, 6-3/8 - 6-3/4
    x
                

    This linkage kit allows you to drive around on just one 4 barrel unless you mash it. Unique linkage is adjustable and is inline for dual quads only.

     

  • Single End Carburetor Linkage Rod, 7 Inches Long
    Single End Carburetor Linkage Rod, 7 Inches Long
    x
                

    3/16" steel throttle rod carburetor linkage with a single end. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • Single End Carburetor Linkage Rod, 3-1/2 Inches Long
    Single End Carburetor Linkage Rod, 3-1/2 Inches Long
    x
                

    3/16" steel throttle rod carburetor linkage with a single end. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • Double End Carburetor Linkage, 3 Inches Long, Non-Adjustable
    Double End Carburetor Linkage, 3 Inches Long, Non-Adjustable
    x
                

    This 3" long, double-end carb linkage is constructed from 3/16" steel rod. Non-adjustable design. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • Moroso 65444 1:1 Slip Linkage Kit for 4150 Holley
    Moroso 65444 1:1 Slip Linkage Kit for 4150 Holley
    x
                These slip links for Holley 4150 carbs are designed to replace the "progressive" stock link to provide simultaneous, 1:1 primary and secondary opening rates.
    • Replaces "progressive" stock link
    • 1:1 primary and secondary opening rates
    • Requires drilling of existing primary throttle arm hole
    • One per package

    54565444 Instructions (PDF)

  • Edelbrock 1033 94 Triple Carb Throttle Linkage Rod Kit, Progressive
    Edelbrock 1033 94 Triple Carb Throttle Linkage Rod Kit, Progressive
    x
                

    The progressive design operates a single or two carburetors to part throttle before synchronizing all three carbutetors to open fully at wide open throttle.  Edelbrock 94 carburetors are equipped with an extended length throttle shaft, making these kits a bolt-on to Edelbrock 94 carbs.

    • Operates a single or dual carb to half throttle and pregresses all three to WOT
    • Saves fuel, provides smoother throttle operation and ends flat spots
  • Single End Carburetor Linkage Rod, 9 Inches Long
    Single End Carburetor Linkage Rod, 9 Inches Long
    x
                

    3/16" steel throttle rod carburetor linkage with a single end. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • Lokar TCB-PLR2 Edelbrock Carb Progressive Linkage Kit on 8-5/8 - 9
    Lokar TCB-PLR2 Edelbrock Carb Progressive Linkage Kit on 8-5/8 - 9
    x
                

    This linkage kit allows you to drive around on just one 4 barrel unless you mash it. Unique linkage is adjustable and is inline for dual quads only.

     

  • Stromberg 97-Style Center Carb Throttle Shaft Arm
    Stromberg 97-Style Center Carb Throttle Shaft Arm
    x
                

    Throttle arms to attach linkage to the 0.282" dia., extended shafts on Stromberg 97's, 9 Super 7 ® and Ford/Holley 94 carbs. Use with 3/16" (10-32) heims and linkage.

    560-6181 Instructions (PDF)

  • Holley 20-3 1 to 1 Throttle Shaft
    Holley 20-3 1 to 1 Throttle Shaft
    x
                This throttle shaft converts throttle linkage to 1:1 ratio. Better throttle response and HP. Fits Holley 4150 carbs.

    Note:  Throttle linkage only fits carbs with 1-11/16" throttle bores.