Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop Air and Fuel Delivery At Speedway Motors

Getting the right mix of fuel and oxygen into your engine can be tricky. Our award winning Techs can help set up a race-winning fuel system that makes serious power, but is reliable enough for your daily driver. From air cleaners to superchargers, Speedway Motors wants to help makes sure you never starve your engine again!

"Air and Fuel Delivery, Fuel Storage" Page 1 of 20

  • RCI 126 Replacement Flapper Valve, 16 Bolt
    RCI 126 Replacement Flapper Valve, 16 Bolt
    x
                

    This fuel tank cap seal flapper is designed to retrofit all RCI Circle Track cells with the 16 bolt oval type 4" cap assemblies.

    This flapper is designed to slow the fuel leakage in the event of a vehicle roll over.

    A must have safety item! 

    • Replacement nylon flapper valve for all "16 bolt top" RCI fuel cells
    • Compatible with gas or alcohol
    • Overall Length: 4-3/8"
    • Overall Width: 3-3/4"
    • Overall Thickness: .03"
    • Clear plastic material

    Note: Per vendor, this flapper valve should be replaced on a yearly basis.

  • Fuel Safe SB225DT 25 Gallon Sprint Car Tank Kit, 12 AN Top with Baffle
    Fuel Safe SB225DT 25 Gallon Sprint Car Tank Kit, 12 AN Top with Baffle
    x
                Fuel Safe has long been the leader in Sprint Car tanks and bladders.  All bladders meet stringent safety requirements and are serial numbered.  Speedway now offers tank kits with or without the anti-surge baffle and the new popular collector options.  All tanks have molded in mounts for all current Sprint Cars.  Tank kits comes complete with pickup and upper plate with cap and vent.  For use with alcohol fuel only.
            
  • JAZ Products 300-000-20 Fender Mount Fuel Filler Kit
    JAZ Products 300-000-20 Fender Mount Fuel Filler Kit
    x
                

    For remote filling of fuel cell. Kit contains a 12-bolt recessed fender fill assembly with vented cap (1/2 turn, twist & lock style). Fender filler flange measures 6-1/4" outside diameter.

    Cap and base are made of galvanized steel. Fill and vent hose are clear polyethylene. Use with fast fill valve.

  • Fuel Tank Roll-Over Vent Valve
    Fuel Tank Roll-Over Vent Valve
    x
                

    This safety device will automatically stop fuel flow if your car somehow gets upside down. Inside is a needle/ball seat which stops fuel flow out the vent if you get upside down.

    • Accepts 5/16" hose
    • Fits into 1/4" npt port
    • Measures 3" bottom-to-top
  • Aeroquip Special Application Socketless AN Hose, Black
    Aeroquip Special Application Socketless AN Hose, Black
    x
                
  • Textile braid reinforcement
  • Low pressure design for use with socketless reuseable fittings only
  • No hose clamp necessary
  • Ideal hose for fuel line applications
  • 50,000 ft of hose in stock!
  • Construction: AQP elastomer tube, textile braid reinforcement, black AQP elastomer cover.

    Application: For gasoline, fuel and lubricating oils, air and water. Not recommended for hydraulic impulse applications and is not approved for air brake, hydraulic brake or power steering applications.

    Operating Range: Max Operating pressure: 250 PSI. Minimum burst pressure: 1000 PSI. Operating Temperature Range -40°F to 300°F. Air not to exceed +250°F and water not to exceed +180°F. Reduced pressure operation allows for temperatures up to 300°F.

    Aeroquip Hose Sizing Guide (GIF)

    Hose Fitting Sizing Chart (GIF)

  • Fuel Safe 7 x 12 Inch Aluminum Fuel Cell Cover Plate
    Fuel Safe 7 x 12 Inch Aluminum Fuel Cell Cover Plate
    x
                

    These replacement front covers are perfect for your fuel cell with a 7" x 12" opening.  They are designed to fit the front side of the tank for your Sprint car and feature quality aluminum construction.

    • Replacement cover
    • Fits front of fuel cell
    • 7" x 12"
    • Aluminum
  • RCI 0111 Fuel Cell Gasket
    $7.99
    $8.99
    RCI 0111 Fuel Cell Gasket
    x
                

    Do you have a worn, damaged, or missing fuel cell filler gasket?  RCI offers an excellent solution with their fuel cell filler gasket replacements.  They're made from durable Viton® material, which is a high-tech elastomer designed for extreme heat, oil, and chemical resistance, making these fuel cell filler gaskets perfect for use with RCI fuel cells.

    RCI Fuel Cell Gasket

    • Overall Height: 9.13"
    • Overall Width: 6.25"
    • Inside Height: 7.25"
    • Inside Width: 4.50"
    • Thickness: .07"
    • For 16 bolt top
    • Rubber
  • Aluminum Fuel Manifold Fitting
    Aluminum Fuel Manifold Fitting
    x
                          This handy little aluminum fuel manifold fitting allows you to plumb all your return lines right at the injector. That saves you weight and space because you don't have to run all the lines back to the tank. Choose AN8 or AN10 to lead to three AN6 male ends.            
            
  • Spun Aluminum Fuel Tank, 11 Gallon, 10 x 33 Inch, Offset Outlet
    Spun Aluminum Fuel Tank, 11 Gallon, 10 x 33 Inch, Offset Outlet
    x
                

    These spun aluminum tanks have an unpolished, spun aluminum finish, 2-1/4" neck, and a 1/4" NPT female outlet. For all off-road vehicles. The screw-on vented cap and brackets are included and can be found in a false bottom of the packaging box.

    This tank features a fuel outlet that is 3" from the end opposite the filler neck.

  • Aircraft Style Fuel Filler Neck & Cap
    Aircraft Style Fuel Filler Neck & Cap
    x
                

    Flush-mount caps offer excellent aerodynamic performance, large fill opening and attractive appearance. Cap features a positive seal, flip-up 1/4-turn handle, and a chain to secure it to the gas filler neck. Includes cap, chain, fuel filler neck, gasket, and all hardware. Polyethylene cap is vented.

    Hole in tank needs to be 3-3/4" for cap to sit flush.

  • Chrome Plated Stainless Steel Flush Mount Fuel Fill
    Chrome Plated Stainless Steel Flush Mount Fuel Fill
    x
                

    This chrome plated stainless steel fuel fill can be flush mounted and includes a special opening key. Simple three hole mounting makes installation a snap.

    Use with 1-1/2" I.D. hose (sold separately).

  • Adjustable Pressure Relief Valve for Belt Drive Fuel Pump
    Adjustable Pressure Relief Valve for Belt Drive Fuel Pump
    x
                

    This pressure relief valve is the ideal bypass valve for use with a positive displacement fuel pump (typically not required for diaphragm type pumps). For use with any carbureted race engine using a belt drive fuel pump. This bypass valve is well suited for alcohol carburetors with gear type pumps.

    Adjustable diaphragm lets you set fuel pressure while the Holley jet inside allows you to reduce idle fuel pressure without affecting operating pressure. Due to fuel pump variations, the jet is not included. The fuel pump relief valve features a stainless steel seat and bronze popitt valve for maximum resistance to corrosion.

    • Easily mounts directly to the carb fuel log
    • Adjusting screw on top sets high RPM fuel pressure
    • Easy pressure adjustments at 7-14 PSI
    • Adjustable to vastly different fuel pumps
    • Maximum fuel availability at the carb
    • 3/8" NPT ports

    910-11579 Instructions (PDF)

  • Black Straight -6 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    Black Straight -6 AN Flare to 3/8 Inch NPT Pipe Adapter Fitting
    x
                

    These straight flare adapters connect 3/8" pipe to straight -6 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Black finish will give your engine compartment the look you are after.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fuel line hose connector
    • -6 AN to 3/8" aluminum pipe adapter
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Black anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Filler Twist Cap with Steel Neck
    Filler Twist Cap with Steel Neck
    x
                

    These filler necks come with a vented cap which vents to the underside of the cap. Steel weld-in 2.25" O.D. bung. Cap locks on the inside of the neck, not on the outside like a radiator cap.

  • Aeroquip Special Application Socketless AN Hose, Blue
    Aeroquip Special Application Socketless AN Hose, Blue
    x
                
  • Textile braid reinforcement
  • Low pressure design for use with socketless reuseable fittings only
  • No hose clamp necessary
  • Ideal hose for fuel line applications
  • 50,000 ft of hose in stock!

    Construction: AQP elastomer tube, textile braid reinforcement, blue AQP elastomer cover.

    Application: For gasoline, fuel and lubricating oils, air and water. Not recommended for hydraulic impulse applications and is not approved for air brake, hydraulic brake or power steering applications.

    Operating Range: Max Operating pressure: 250 PSI. Minimum burst pressure: 1000 PSI. Operating Temperature Range -40°F to 300°F. Air not to exceed +250°F and water not to exceed +180°F. Reduced pressure operation allows for temperatures up to 300°F.

    Aeroquip Hose Sizing Guide (GIF)

  • Hose Fitting Sizing Chart (GIF)

  • JAZ Products 200-016-NF Polyethylene Fuel Cell, 16 Gallon
    JAZ Products 200-016-NF Polyethylene Fuel Cell, 16 Gallon
    x
                

    These polyethylene fuel cells are the best cells on the market! This 100% seamless polyethylene cell features one -8 AN pick-up fitting and one -8 AN vent/tip-over valve fitting. These fuel cells contain a pickup tube. All cells are NHRA, IHRA, SCORE, and DIRT approved.

    • Seamless cross-linked polyethylene outer shell 
    • D-ring bail handle cap assembly
    • 360 degree mouting strap recesses
    • Does not include fuel cell safety foam
  • Jaz-Speedway Fuel Cell Flapper Valve
    Jaz-Speedway Fuel Cell Flapper Valve
    x
                

    This flapper valve or rollover valve, installs in the fuel cell and is retained by the bolts used to secure the filler cap flange to the cell.

    When fueling the cell, the rubber flap opens. If the cell should become inverted, the rubber flap closes to seal off the filler opening so that fuel cannot leak out.

    A must have safety item! 

    IMCA approved.

    458-315 Instructions (pdf)

  • Steel Weld Bung for 1 Inch I.D. Tube, 3/4-16 RH
    Steel Weld Bung for 1 Inch I.D. Tube, 3/4-16 RH
    x
                

    Heavy duty steel weld bungs for splitting wishbones, custom tie rods or custom suspension control arms. These weld bungs are 1” O.D. where they slide into the steel 1" I.D. tubing.

  • Polyethylene Fuel Cell Mounting Straps, 16 Gallon
    Polyethylene Fuel Cell Mounting Straps, 16 Gallon
    x
                

    Zinc-plated steel mounting straps available for 16 gallon seamless polyethylene fuel cells (non-steel can cell design).

    NOTE: These straps do not work with steel can fuel cells.

    Must be used with cell #s 458-116 or 458-0458 only

  • Speedway Fuel Cell Foam, 14 x 4 x 6 Inch
    Speedway Fuel Cell Foam, 14 x 4 x 6 Inch
    x
                

    Compatible with gasoline, E85, or alky fuels (not recommended for use with nitro-methane). This fuel cell safety foam keeps weight transfer/shift to a minimum, which provides you with more responsive and predictable handling. Can be cut and stacked as needed.

    • 8-12 gallon cells typically use 3-8 sticks
    • 16 gallon cells typically use 4-10 sticks
    • 22-32 gallon cells typically use 8-14 sticks

    Blocks are sold EACH.

  • Straight Chrome Fitting, 3/8 Inch Hose to 3/8 Inch NPT
    Straight Chrome Fitting, 3/8 Inch Hose to 3/8 Inch NPT
    x
                

    These chrome plated push-on brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb ends
    • 3/8" Hose to 3/8" NPT adapter
    • Fuel line hose connector
    • Straight angle
  • Black Straight -6 AN Flare to 1/4 Inch NPT Pipe Adapter Fitting
    Black Straight -6 AN Flare to 1/4 Inch NPT Pipe Adapter Fitting
    x
                

    These straight flare adaptors connect 1/4" pipe to straight -6 AN fittings. They are lightweight aluminum and feature a 37° sealing angle.  Black finish will give your engine compartment the look you are after.  Order your desired size.

    • Precision machined to ensure precise thread engagement
    • Lightweight aluminum fuel line hose connector
    • -6 AN to 1/4" aluminum pipe
    • 37° sealing angle guarantees a positive seal at maximum operating pressures
    • Available in Black anodized finish for a custom look

    Fitting Thread Application Chart (GIF)

  • Fuel Tank Sealer, Quart
    $27.99
    Product Rating: 4.75 Stars
    Fuel Tank Sealer, Quart
    x
                

    This tank sealer seals gas tanks, aluminum, and even rusty steel. Not affected by fuel additives, octane boosters, ATF hydraulic fluid, brake fluid or oil. Remains flexible. One quart.

    • STAYS FLEXIBLE – Will never crack or peel off.
    • ALCOHOL RESISTANT – No expensive come-backs.
    • BRIGHT BLUE COLOR – Both you and your customer can see results.
    • COVERS RUST – Seals old rust in and prevents future rusting.
    • SEALS LEAKS – Gets the multitude of pin-holes you can’t find.

    *Cannot Ship By Air*

    910-16752 Instructions (PDF)

    Tank Sealer FAQ (PDF)

    Material Safety Data Sheet (PDF)

     

     

  • Professional Products 10415 Holley 4150 Dual Feed Fuel Line Kit, -8 AN
    Professional Products 10415 Holley 4150 Dual Feed Fuel Line Kit, -8 AN
    x
                These dual feed fuel line kits give you the looks, performance and flexibility your car deserves. Fuel log features -8 AN inlet, 1/8" NPT tapped fuel pressure gauge port, and allows you to have a fuel tank return if needed.

    Fuel line fits Holley 4150 style Double Pumper carburetors with 7/8"-20 inlets.

  • Straight Chrome Fitting, 5/16 Inch Hose to 1/4 Inch NPT
    Straight Chrome Fitting, 5/16 Inch Hose to 1/4 Inch NPT
    x
                

    These socketless chrome plated brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb connector
    • 5/16" Hose to 1/4" NPT adapter
    • Straight angle
  • Aluminum -8 AN Female to -6 AN Male Reducer Fitting
    Aluminum -8 AN Female to -6 AN Male Reducer Fitting
    x
                

    Aluminum female to male adapter for 37° AN pipe fittings. Blue anodized finish.

    • -8AN female to -6AN male fuel line hose connector

    Fitting Thread Application Chart (GIF)

  • 1-1/2 Inch Aluminum Remote Fuel Cell Filler Neck Flange Assembly
    1-1/2 Inch Aluminum Remote Fuel Cell Filler Neck Flange Assembly
    x
                

    These filler necks are manufactured from top-quality materials and are available in two sizes to best suit your application. You can count on these fuel cell filler necks to complete your performance fuel setup.

    1-1/2 Inch Aluminum Remote Fuel Filler Neck Flange Assembly 

    • O.D. of flange is 5-1/16"
    • 6 mounting holes on a 4.36" bolt circle
    • Filler neck is 1-1/2" O.D.
    • Includes mount ring, bolts and gasket

    This flange bolts to your fuel cell to permit attachment of a 1-1/2" I.D. filler hose. Aluminum construction.

  • Garage Sale - Total Performance 11 Inch Windshield Slug, With Hole
    Garage Sale
    Garage Sale - Total Performance 11 Inch Windshield Slug, With Hole
    x
                

    Aluminum windshield slug material designed for Total Performance's round tube "T" style windshields.  This slips inside the tubing to allow you to attach hinges, glass clips and the frame to the posts.

     

    This is garage sale priced because it has been discontinued.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS   

  • Garage Sale - Gasket For 4 Inch Fuel Cell Filler Neck
    Garage Sale
    Garage Sale - Gasket For 4 Inch Fuel Cell Filler Neck
    x
                

    Replacement gasket for 4" fuel cell filler neck 

     

    This filler neck gasket is garage sale priced because it has an adhesive backing different than what we currently offer. 

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS    

  • Aeroquip FBG0600 FC300 High Pressure Hose, -6 AN, Per Ft.
    Aeroquip FBG0600 FC300 High Pressure Hose, -6 AN, Per Ft.
    x
                

    Aeroquip FC 300 hose is designed for high pressure fluid applications such as power steering line. The FC300 hose features a blue, abrasion-resistant fabric cover over a synthetic rubber inner tube for longer life. This high pressure hose is ideal for power steering, hydraulics, air, fuel and lubricating oil applications.

    • Max operating pressure is 2250 psi
    • Minimum bend radius is 4"
    • Temperature range of -55°F to +300°F
    • Hose is sold by the foot

    Note: The FC300 Hose only works with FC300 steel fittings (not included). Easily assembles with a bench vise and/or wrenches. Ends are reusable.

    AN Thread Sizing Guide (GIF)

    AN 6 Hose Application Chart (GIF)

  • Straight Chrome Fitting, 3/8 Inch Hose to 1/4 Inch NPT
    Straight Chrome Fitting, 3/8 Inch Hose to 1/4 Inch NPT
    x
                

    These chrome plated brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb end
    • 3/8" Hose to 1/4" NPT adapter
    • Straight angle line connector

     

  • Chrome 90   Adapter Fitting, 3/8 Inch Hose to 1/4 NPT
    Chrome 90 Adapter Fitting, 3/8 Inch Hose to 1/4 NPT
    x
                

    These chrome plated brass fittings are the perfect finishing touches for your fuel system. They are made of brass and feature a chrome plated finish for a show car shine.  All fittings are male hose barb to male pipe thread.

    • Male pipe threads to hose barb ends
    • 3/8" Hose to 1/4" NPT
    • 90 Degree angle
  • Aeroquip Straight Full Flow Swivel Hose End Coupler Fitting, -6 AN
    Aeroquip Straight Full Flow Swivel Hose End Coupler Fitting, -6 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a red and blue anodized finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617306).

    • -6 AN female to push-on style adapter
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • Unique taper design ensures easy assembly
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Accepts a variety of lightweight aluminum AN style adapters & fittings
    • Works great with custom fuel lines
    • Available in Red/Blue corrosion resistant finish

    Straight full flow ends come in sizes of AN4, AN6, AN8, AN10, AN12, and AN16.

    Fitting Thread Application Chart (GIF)

  • Spun Aluminum Fuel Tank, 11 Gallon, 10 x 33 Inch, Centered Outlet
    Spun Aluminum Fuel Tank, 11 Gallon, 10 x 33 Inch, Centered Outlet
    x
                

    These spun aluminum tanks have an unpolished, spun aluminum finish, 2-1/4" neck, and a 1/4" NPT female outlet. For all off-road vehicles. The screw-on vented cap and brackets are included and can be found in a false bottom of the packaging box.

  • Straight Aluminum Bulkhead Flare Fitting, Blue, -6 AN
    Straight Aluminum Bulkhead Flare Fitting, Blue, -6 AN
    x
                

    Straight aluminum bulkhead fitting for 37° AN flare. Blue anodized.

    AN Thread Sizing Guide (GIF)

    Fitting Thread Application Chart (GIF)

  • Aluminum Bulkhead Jam Nut, Blue, -3 AN
    Aluminum Bulkhead Jam Nut, Blue, -3 AN
    x
                

    Aluminum bulkhead jam nuts for AN fittings. Blue anodized finish.

    AN Thread Sizing Guide (GIF)

    Fitting Thread Application Chart (GIF)

Goto Previous PagePrevious Page
1 2 3 4 5 ... 20