Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf

Pushrod for Slave Cylinder

SAME DAY SHIPPING! Order within the next 1 hour 32 minutes and receive same day shipping

Specs
Material Type:
Steel
Sold in Quantity:
Each
Finish:
Zinc
Min. Mounting Distance:
6.600
Max. Mounting Distance:
7.00
Diameter Small End :
0.3680
Diameter Big End:
0.490
Pushrod for Slave Cylinder
Pushrod for Slave Cylinder

Click image to enlarge

Speeday Motors Logo
X
Pushrod for Slave Cylinder

Details

Reviews

Q & A

What's in the Box

Adjustable pushrod for push-type slave cylinder 910-25605.

You may also be interested in:

Speedway GM Standard Clutch Throwout Fork
                        Standard style fork with a pocket for the clutch pushrod. Fork fits 1973-1984 GM 6 & 8 cylinder cars and trucks. May fit earlier vehicles with slight modification.
                    
Push Type Slave Cylinder
                        

Push type slave cylinder with 7/8" bore size. Has approximately 1.25" of travel. Inlet fitting that comes on the cylinder is 3/8 x 24 IFF. Has 2-3/8" mount bolt centers. 

Pushrod sold separately (910-25606).

Note: If you want to plumb AN3 or AN4 lines, order 1/8 NPT to AN3 or AN 4 in either straight, 45 degree, or 90 degree and remove the fitting that comes installed.

Speedway Pull Type Slave Cylinder
                        

Speedway pull type slave cylinder with 7/8" bore for clutch use. Works great with stock-style hydraulic throwout bearings or Ram Couplers. Has a 3/8"-24 inverted flare female inlet. Bleeder adapter and bleeder are included.

  • Ram shaft is 3/8" O.D.
  • Cylinder body is 4.09" long
  • Cylinder body is 1-7/16" O.D. at end by fittings
  • Cylinder body is 1-3/8" at opposite end of fittings

A 5/16” heim will fit both ends of cylinder (not included). Our heim part number is 1750202.

Note: For most multi-disc clutch set-ups we recommend the use of a smaller 3/4" bore master cylinder.

Wilwood 260-1304 Integral Reservoir Alum. Master Cylinder, 3/4 In Bore
                        

This popular, lightweight, compact design is used for clutch and small master cylinder requirements and is well known for its dependability. It incorporates an improved plastic screw-on filler cap which protects the fluid in the 1.4 ounce reservoir.

  • Includes fitting to accept 3/8"-24 inverted flare from 3/16" hard line
  • If AN-3 or AN-4 flex line is to be used, the following adapters will work:
    • 910318-3/8  (3/8"-24 to AN-3 Male Brake Fitting)
    • 6174030  (3/8"-24 Inverted Flare to AN-4 Fitting)

External Dimensions (Link)

Learn more about selecting the proper master cylinder for your vehicle by reading our tech article. Brake System Selection

Forged Steel Yoke for 3/8 Inch Rod
                        Tapped for 3/8" fine threaded bolt or rod.
                    
Standard Steel Heim Joint Rod Ends, 3/8-24 RH Female
                        

Standard rod ends are for general purpose applications and are a 2-piece design with a low carbon steel body and a hardened steel ball without a race (metal to metal contact).

Applications: Clutch, brake, steering linkage, & suspension components on moderate horsepower applications.

Assembly Tip: To ease assembly, be sure to run a tap or die through the threads on chrome plated fasteners and apply an anti-seize compound to prevent galling of the threads.

3/8 Inch Clevis
                        

This is a neat clevis with many potential uses, including connecting a master cylinder or booster pushrod to your brake pedal arm. Overall length is 2”, and it’s tapped for 3/8” fine thread. Comes with a 3/8" diameter clevis pin and cotter key.