McAfee SECURE sites help keep you safe from identity theft, credit card fraud, spyware, spam, viruses and online scams
Phone

800.979.0122

Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Panhard-Behind Rear End Bracket - Weld On

SAME DAY SHIPPING! Order within the next 9 hours 26 minutes and receive same day shipping

Specs
Material Type:
Steel
Overall Width:
6.71
Overall Length:
5.00
Sold in Quantity:
Each
Overall Thickness:
3.09
Finish:
Natural
Hole Diameter:
.75
Material Thickness:
.18
Notes
Fits 3.00" diameter tube.
Panhard-Behind Rear End Bracket - Weld On

Click image to enlarge

Details

Reviews

Q & A

What's in the Box

These behind rear end panhard bar brackets have four 3/4" holes for changing roll center and panhard bar angle. Fits 3" axle tube. Weld-on.

Specs


Customer Reviews

Rated 5 out of 5 by 3 reviewers.
RATING BREAKDOWN
3 reviews
5 Stars
3
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
RECOMMEND THIS PRODUCT:

geno
Verified Purchaser
martinez,ga.
Product Rating

weld-on panhard bracket

March 03, 2011
i'll have to fab my frame bracket,but the weld-on rear end bracket saves a lot of time
Pros:
  • Improves Handling
  • Easy To Install
  • Adjustable
No, I would not recommend this product.
Full Size Image

Was this review helpful? 0 0

krappy
algona iowa
Product Rating

good for our situation

February 12, 2010
in sport mod rules you have to run the long pan hard bar so we take this bracket and weld it close to the center section so we can run minimum length so it works like a j bar car is not so tight
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Camaro lover
Verified Purchaser
Bend, Oregon
Product Rating

"As Always"

November 09, 2010
As Always the products from Speedway are well built and affordable! Thank you guys!
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Page 1 of 1

Product Q&A

0 questions : 0 answers

No questions have been asked.

You may also be interested in:

Straight Panhard Bar
(Part #9164551)
                        

Straight steel panhard bar, 26-1/2" eye-to-eye. With 3/4" heims.

Note: When using these bars, your specific application my require the use of heim spacers for maximum range of motion. Spacing out the mounting tabs prevents the heim joint body from making contact with the them. This provides for greater misalignment (range of motion) without decreasing hole size.

If your application requires the use of misalignment spacers then 910-07000 would be the best one for you.  It is ½” thick and when you use one on each side of the heim they will add a total of 1” of thickness.  910-07001 could also be used if you need to space out further from your mounting point as it is 1” thick.

 

Panhard Bar Bracket, 3 Inch Tube Clamp
(Part #91645524)
                        This steel Panhard bar bracket is a single mount, clamp-on style Panhard bracket. Fits 3" axle tubes.
                    
BSB Manufacturing 7043 Extra Long Panhard Bar
(Part #91645580)
                        This extra long panhard bar only has one end installed allowing you to custom fit for your car.  Has 3/4" rod ends and is 30" center to center. 
                    
BSB Manufacturing 7053 Adj Panhard Bar Axle Mount, 3 In Tube Clamp
(Part #91645585)
                        This adjustable panhard bar axle mount clamps to 3" axle tubes and gives you 3" of adjustment. Works with 916-45580 panhard bar. Stud is 3/4". Steel.
                    
Behind Rear End Panhard Bar Bracket - Clamp On
(Part #91645516)
                        These behind rear end panhard bar brackets have four 3/4" holes for  changing roll center and panhard bar angle. Fits 3" axle tube. Clamp-on.