Products to Compare (max of 3)
X
Compare
ALWAYS SECURE
America's Oldest Speed Shop ® 800.979.0122 Lincoln, NE
Filters
Menu
Contact
Help Center
x
x
How to Contact Us

U.S.Order Line:

800.979.0122

(CST) 7am - 10pm

Race and Rod Tech Support

Mon-Fri 8am - 5pm

Canadian Order Line:

855.313.9180

International Order Line:

1.402.323.3200
Since 1952
Menu
x

Pro/Cam Racing 9350 Chevy 6-Valve Mechanical Fuel Pump-130 GPH, 15 PSI

SAME DAY SHIPPING! Order within the next 14 hours and receive same day shipping

Free Shipping Free Shipping
Pro/Cam Racing 9350 Chevy 6-Valve Mechanical Fuel Pump-130 GPH, 15 PSI
Pro/Cam Racing 9350 Chevy 6-Valve Mechanical Fuel Pump-130 GPH, 15 PSI
Pro/Cam Racing 9350 Chevy 6-Valve Mechanical Fuel Pump-130 GPH, 15 PSI
Pro/Cam Racing 9350 Chevy 6-Valve Mechanical Fuel Pump-130 GPH, 15 PSI

Click image to enlarge

Details

Reviews

Q & A

What's in the Box

This pump may look similar to others on the outside, but the internal components of the ProCam fuel pump have been re-engineered to reduce leaks and maintain pressure. It is completely reworked to increase flow, and machined with 1/2" inlet and outlet to get more fuel to the engine faster. Maintains more constant pressure at high rpms. Blueprinted for longevity and quality.
  • Re-engineered to reduce leaks and maintain pressure
  • Completely reworked to increase flow, and machined with 1/2" inlet and outlet to get more fuel to the engine faster
  • Small Block Chevy applications rated up to 1200 HP on gas; up to 600 HP on alcohol or E85
  • 6 valve, 130 GPH
  • Use of a regulator is recommended for 15 psi fuel pumps

Notes

Tech Tips

  • Running alcohol?  To prevent seals and other components from drying out and leaking, flush the pump with gasoline on a regular basis to lubricate the seals.  This is particularly important at the end of the season
  • PSI is rated at full throttle and may be higher at idle
  • If you need to reclock the pump, remove all bolts and separate the pump body into two sections (top and bottom) before rotating

Warranties

ProCam Warranty Information (PDF)

Customer Reviews

Rated 3.8 out of 5 by 6 reviewers.
RATING BREAKDOWN
6 reviews
5 Stars
2
4 Stars
3
3 Stars
0
2 Stars
0
1 Star
1
RECOMMEND THIS PRODUCT:

None
Verified Purchaser
Montana

Good pump

July 10, 2015
Pump delivers consistent volume and pressure
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Buddy mertz racing
Verified Purchaser
Boyertown, pa

This is the only fuel that we will use on our dirt latemodel

June 28, 2015
This is the only fuel pump that we are confident enough to use on our dirt late model.
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Nseale1s
Fort Branch, IN 47648, USA

Highly recommend

June 18, 2014
Very pleased with my Pro/Cam fuel pump. I currently have my fuel pressure at 9 psi and this is no problem for the Pro/Cam Fuel Pump. I have ran this for about a year and a half on my UMP modified with no leaks and no cracks in casing as I have had with other fuel pumps. I highly recommend this product
Pros:
  • quality constructed base
  • 1/2 inlet and outlet
  • maintains fuel preasure
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Garry10b
Prairie Village, KS, USA

This fuel pump is one of the best I've o

June 18, 2014
I'm very satisfied with this fuel pump. I've owned other pumps from other manufacturers that cost way more and this pump by fare competes with them in performance (and even out performs most of them) and beats them in bang for the buck Good steady flow never had a fuel delivery problem with this pump
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

kairu18
salinas, ca

my pumps work great have them on 3 modif

April 28, 2014
these pumps work great on our GRT modifieds. only tricky part is clocking the pump without tearing the diaphragm, which is easily done by completely separating the two halves then rotating them. pumps put out adequate pressure and have not had any problems after 25 races on them so far.
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

racer77

problems with it off the get go

September 07, 2013
ran this pump this 3 races and it went bad already dropped fuel pressure , good flow from line pull line off and fuel runs out junk part.
No, I would not recommend this product.
Full Size Image

Was this review helpful? 0 0

Merchant Response:

Racer77, thank you for your feedback. We apologize for any inconvenience this may have caused. If you wish to contact the manufacturer for refund/replacement options, please note the warranty tab on the product page for this item. The link displayed will show a form regarding the information you will need to do so. Again, we appreciate your consideration and are happy to help in any way.
Page 1 of 1

Product Q&A

4 questions : 5 answers

1 answers

was does the numbers and or letters represent that are hand engraved on the top part of pump........78764 over the letter G under that its 8443

McGowanRaceParts
Kenova, West Virginia
May 29, 2014

was does the numbers and or letters represent that are hand engraved on the top part of pump........78764 over the letter G under that its 8443

Answers

May 29, 2014
EricM
Those numbers are not significant for anything. It may be an individual component part number or possibly a serial number. It has no significance for our purposes.
1 answers

If the pump fails does the fuel end up in the crank case

jason86
April 30, 2014

If the pump fails does the fuel end up in the crank case

Answers

April 30, 2014
EricM
It is possible for fuel to make it into the crankcase if the pump fails but it's not very likely. There is a vent hole in the top of the pump where the fuel will come out of if the diaphragm fails or starts leaking. You will usually notice fuel spilling onto the ground long before any fuel makes it into the crankcase. This is typical of all mechanical fuel pumps.
2 answers

I assume the fitting are 1/2 NPT for this pump, so I need a 1/2 NPT x #8AN fitting for braided lines

BigMo
October 31, 2013

I assume the fitting are 1/2 NPT for this pump, so I need a 1/2 NPT x #8AN fitting for braided lines

Answers

June 19, 2014
Nseale1s
You are correct.
October 31, 2013
Jason
Yes, the Pro/Cam racing fuel pump does have 1/2" NPT inlet and outlet. Speedway offers fitting part #6176049 for AN 8 or 6176050 for AN10. We also offer these fitting in 45 and 90 degree.
1 answers

What fuel pressure regulator will work best with this pump to run on a alcohol motor?

imca37
August 28, 2015

What fuel pressure regulator will work best with this pump to run on a alcohol motor?

Answers

August 31, 2015
Eric
Expert
Fuel pressure regulator 42512704 works well with this pump. This combination can be used on alcohol or gasoline.
Page 1 of 1

You may also be interested in:

Edelbrock 1711 Small Block Chevy Victor Series 130 GPH Fuel Pump
(Part #3251711)
                        

A must for drag racing, circle track racing, street machines or any application that demands a high-volume fuel delivery, these Small Block Chevy fuel pumps feature a brilliant three stage polished finish. High-volume 3/8" NPT inlet and outlet orifices surpass the capacity of conventional models. Produces 10 psi and must be used with an external fuel pressure regulator. Flow capacity of 130 gallons per hour. For gasoline only. Clockable lower housing can be rotated for best inlet/outlet alignment.

Small Block Chevy Fuel Pump Installation Instructions (PDF)

Item Details

Gasoline Only - 10 PSI
C&S Specialties Small Block Chevy Alcohol Fuel Pump
(Part #2384230)
                        

C&S Specialties has addressed all problem areas of previous 6-valve pumps in designing their rugged Tool Steel mechanical fuel pumps. This exclusive casting design adds material in 7 places to eliminate cracking, breakage, waviness and leakage. Plus, six High Flow pumping valves, combined with internal porting, are proven to deliver twice the fuel flow over other 6-valve alcohol pumps.

  • Unique baked-on coating to resist corrosion
  • Unique stepped diaphragm reduces stress and increases life
  • Two stainless steel springs instead of one increases reliability
  • CNC milled pump arm from tool steel, not stamped steel
  • Pump arm bushing made from tool steel
  • Pump shaft also made of tool steel, not stamped steel
  • 1/2" NPT inlet and outlet
Speedway Small Block Chevy 110 GPH Racing Fuel Pumps
(Part #5791002)
                        Why pay more when our 6-Valve Racing Pumps will get the job done? These 110 GPH fuel pumps are race tested and proven. The inlet and 3/8" NPT outlet are spaced 180° apart, and the pump head can be clocked for more clearance, if needed.  

Fits Small Block Chevy 283-400 engines.

  • 3/8" NPT
  • Heavy-duty, fiber-reinforced diaphragm
  • Color-coded springs – matched to O.E. specifications
  • Zinc-plated valves for corrosion-resistance
  • Zamak alloy casting for durability and corrosion-resistance
  • Zytel® spring retainer for smoother, quieter operation
  • Heavy-duty rubber seals protect against leaks
  • Heat-treated rocker arms
  • 100% factory tested for assurance of quality
  • Made in the USA
  • 3/8" NPT Outlets
  • 7 PSI Gas ONLY
Pro/Cam Racing 9351 Chevy 6-Valve 7.5 PSI Mechanical Fuel Pump-130 GPH
(Part #9109351)
                        This pump may look similar to others on the outside, but the internal components of the ProCam fuel pump have been re-engineered to reduce leaks and maintain pressure. It is completely reworked to increase flow, and machined with 1/2" inlet and outlet to get more fuel to the engine faster. Maintains more constant pressure at high rpms. Blueprinted for longevity and quality. 
  • Re-engineered to reduce leaks and maintain pressure
  • Completely reworked to increase flow, and machined with 1/2" inlet and outlet to get more fuel to the engine faster
  • Small Block Chevy applications rated up to 1200 HP on gas; up to 600 HP on alcohol or E85
  • 6 valve, 130 GPH
  • Use of a regulator is recommended for 15 psi fuel pumps

Changing the Spring Illustration (GIF)

Holley 12-327-35 225 Plus GPH Ultra HP Series Mechanical Fuel Pump
(Part #4251232735)
                        

The Ultra HP Billet Mechanical Fuel Pumps. They're constructed from CNC machined 6061-T6 aluminum to provide the utmost in strength and superior looks. These pumps not only look good they also perform. The Ultra HP Series pumps were put thru extensive durability testing before they were released for production. This equates to a rock solid, long lasting fuel pump. They come standard with -10 AN inlet and -8AN outlet fittings. They are intended for hard core strip use or they are perfect for use in circle track classes.

  • Ultra HP series flow 225 GPH
  • Made from 6061-T6 billet aluminum for durability & good looks
  • Hard coat anodized for corrosion protection
  • Fittings included; -10 AN inlet and -8 AN outlet
  • Preset shutoff pressure of 10-11 PSI
  • Bases are independently rotatable from the top for ease of installation
  • Inlet and outlet are tapped 3/4-16 straight O-ring
  • Requires a fuel pressure regulator
  • Pump is completely rebuildable
  • For use with Alcohol fuels
  • Intended for hard core strip use or is perfect for use in circle track classes
  • Requires the use of a fuel pressure regulator such as Holley part number 12-704.

Installation Instructions (PDF)