ALWAYS SECURE
America's Oldest Speed Shop ® 800.979.0122 Lincoln, NE
Filters
Menu
Contact
Help Center
x
x
How to Contact Us

U.S.Order Line:

800.979.0122

(CST) 7am - 10pm

Race and Rod Tech Support

Mon-Fri 8am - 5pm

Canadian Order Line:

855.313.9180

International Order Line:

1.402.323.3200
Since 1952
Menu
x

LS Low Oil Level Sensor Plug

Specs
Sold in Quantity:
Each
Wrench Type:
Hex
Thread Pitch:
20MM-1.5
Wrench Size:
1" SAE
Gasket(s) Included:
Yes
LS Low Oil Level Sensor Plug
LS Low Oil Level Sensor Plug
LS Low Oil Level Sensor Plug

Click image to enlarge

Details

Reviews

Q & A

What's in the Box

There's a pretty good chance you aren't using the low oil level sensor that is sticking out of the oil pan on your LS engine. These plugs replace the sensor and clean the pan up. Fits 99-up Vortec and 97-up Corvette and F-body LS1 oil pans.

  • Thread Diameter:  20mm O.D. (25/32")
  • Wrench Size:  1"

Customer Reviews

This product has no reviews.

Product Q&A

0 questions : 0 answers

No questions have been asked.

You may also be interested in:

Auto Meter 2268 LS Series Oil Pressure Sender Adapter
(Part #1822268)
                        

This LS Series oil pressure sender fitting allows your aftermarket 1/8" NPT oil pressure sending unit to be installed in place of the OEM oil pressure sender.

When installing aftermarket gauges, the OEM oil pressure sender is not required by the PCM and may be replaced by the aftermarket sender of your choice.

Item Details

16mm-1.5 Male to 1/8" Female
Auto Meter 2277 Temperature Sender Adapter Fitting, 1/8 NPT-M12x1.5
(Part #1822277)
                        

This LS Series water temperature sender fitting allows your aftermarket 1/8" NPT water temperature sending unit to be installed in your passenger side cylinder head.

Note: I.D. of this adapter where the sender probe will go through is .309 and would require drilling to approximately 5/16" or .312 for a Stewart Warner sender to pass through.

Item Details

12mm-1.5 Male to 1/8" Female
LS Low Oil Level Sensor Plug w/ 1/8 NPT Port
(Part #481201)
                        

There's a pretty good chance you aren't using the low oil level sensor that is sticking out of the oil pan on your LS engine. These plugs replace the sensor and clean the pan up. If you want to run an oil temp gauge, order the plug with the 1/8” NPT hole in it. Fits 99-up Vortec and 97-up Corvette and F-body LS1 oil pans.

  • Thread Diameter:  20mm O.D. (25/32")
  • Wrench Size:  1"
Auto Meter 5284 GM LS Sensor Fitting Installation Kit
(Part #1825284)
                        

Swapping an GM LS or LQ series engine into your project and trying to figure out how and where to connect all your gauges? This is what you need! This LS Install Kit from Auto Meter includes a full color booklet with step by step instructions and photos documenting the most common installation points for essentials like oil pressure, coolant temp, RPM and more! In addition to the handy manual compiled by Auto Meter's R&D staff, the kit also includes a package of commonly used adapter fittings to assist with the mounting of your gauge sensors, a short depth temperature sensor specific to the LS / LQ installation requirements, and a pull up resistor used when connecting a tachometer to your engine's ECU.

Includes;

  • 10,000 Ohm Pull Up Resistor
  • 1/8"NPTF Short Depth Eletric Water Temp Sensor
  • M16x1.5 Male to 1/8" NPTF Female adapter for oil pressure
  • M12x1.5 Male to 1/8" NPTF Female adapter for water temperature
  • For installation of Auto Meter Full Sweep and Short Sweep Electric Gauges ONLY!