Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf

Inline Vibration Dampener

SAME DAY SHIPPING! Order within the next 11 hours 34 minutes and receive same day shipping

Specs
Overall Length:
4.00
Sold in Quantity:
Each
Outside Diameter:
1.75
End #1:
3/4 inch DD
Mounted Length:
3.00
Inline Vibration Dampener
Inline Vibration Dampener

Click image to enlarge

Speeday Motors Logo
X
Inline Vibration Dampener

Details

Reviews

Q & A

What's in the Box

Here's the solution to painful, tiring impulses that the roadway transmits through your steering system. Each end accepts a 3⁄4" DD shaft to allow inline installation between steering column and steering box.

A steering shaft support heim is recommended near the dampener for the most stable installation. Bright, nickel-plated steel construction. 3⁄4" DD female on one end, 3⁄4" DD male on the other.

Approximately 1-3/4" O.D. and 4" long end-to-end. Adds approximately 3-1/2" to the length of the shaft. 

Spline Size (Link)

You may also be interested in:

Steel Jam Nuts, 3/4 Inch-16 NF Fine Thread, Pack/6
                        

If you've got spherical rod ends on your vehicle, you'll probably need jam nuts. You might also need them for tie-rod ends or other types of fittings and connectors. Our jam nuts are made from premium steel (zinc-coated for corrosion prevention), and they're available with either right hand or left hand threads.

These steel fine thread jam nuts are for use with rod ends, heim joints, and clevis.

  • 3/4 Inch-16 NF Fine Thread
  • Sold in bags of six nuts.
  • Choose left or right thread.
Steering Shaft, 3/4 Inch O.D. Double D, 4-16 Inch Lengths, Steel
                        

This steering shaft is 3/4" O.D DD. This steering shaft also has a 1.00" long "D" design on each end.

This steering shaft entails:

  • 1018 Steel
  • Weld on
  • Excellent for steering shafts or other uses 
  • Order desired length

NOTE: This DD shaft is only milled with flats on both ends for 1" of length of the shaft. It is not milled the entire length of the shaft and therefore, can not be cut to length unless it is going to be welded to a 3/4" round or has new flats milled into the end. Please see Flaming River DD shaft if fully machined DD shaft is required.

Firewall Mount Flanged Bearing for Steering Shaft
                        This firewall mount allows up to 30° of mis-alignment. Includes ball with two pressed steel flanges with 5/16" square mounting holes. 

Choose 3/4" (750) or 1" (1000) shaft size.

91032375-1000

  • Height: .74"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"
91032375-750
  • Height: .87"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"
Polished Stainless Steel 3/4 O.D. Double D Shaft
                        

Steering shafts that are just plain looking look kind of silly with those shiny stainless steel U-joints. Our polished, stainless steel, double D steering shaft would be more compatible. We offer steering shafts in 18", 22", and 36" cut to fit lengths.

 

Steering Shaft, Fully Machined Double D Shaft, Raw 22 Inch
                        

 Speedway now offers a steering shaft that is 3/4" DD machined the entire length of the shaft. This makes it easier to set up your steering. The carbon steel steering shaft come in 22".

 

Steering Shaft, Fully Machined Double D Shaft, Raw 36 Inch
                        

Speedway now offers a steering shaft which is 3/4" DD machined the entire length of the steering shaft. This makes it easier to set up your steering.The carbon steel steering shaft come in 36".

 

Angled Heim Joint Rod End Support Bracket
                        Over all length of 3 1/2 inches long. Offered with a 3/4" clearance hole for steering heim with a slotted adjustment of 1 7/8 inch long angled at a 45 degrees.  Bracket is 3/16 thick steel
                    
Steering Shaft, Fully Machined Double D Shaft, 18 Inch
                        

Speedway now offers a steering shaft which is machined 3/4" DD the entire length of the steering shaft. This make it easy to set up your steering. This carbon steel DD steering shaft if offered in 18 lengths.

 

Steel Heim Joint Rod Ends for Steering Shaft, 3/4-16 RH Male .757 Hole
                        3/4" heim for steering shaft.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.


Steering Shaft Aluminum Heim Joint Rod Ends, 3/4-16 RH Male, .757 Hole
                        3/4" heim for steering shaft.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.
                    
Flat Heim Joint Rod End Support Bracket
                        Overall length of 3 1/2 inches long.  Offered with a 3/4 clearances hole for steering heim with a slotted adjustment of 1 7/8 inch long. Bracket is 3/16 thick steel.