Holley 36-182 4150 Carb Tuning-Calibration Kit
Click image to enlarge
Please NOTE the following about this product:
- This item is sold as a kit.
Q & A
What's in the Box
This tuning kit contains a selection of main jets, pump nozzles and power valves in popular sizes. All contained in a handy and durable plastic case. Gaskets are included to facilitate carburetor reassembly.
For gasoline carbs only. Fits Model 4150 "Double Pumper" carburetors.
- 4 Each - 8 Metering Jet Sizes ranging from #70-84
- 2 each #35 and # 37 pump nozzles
- 3 Power Valves sizes 3.5, 4.5 and 5.0
- 12 Metering Block Gaskets
- 12 Fuel Bowl Gaskets
- Misc. Pump Nozzle
- Misc. Power Valve
- Misc. Fuel Bowl Screw, pump nozzle and power valve Gaskets
Item DetailsGasoline Only
- Various parts
- Easy to keep organized
- Works on multiple carbs
No questions have been asked.
You may also be interested in:
Willys Carbs WCD3003 Carburetor Float Adjusting ToolPrice: $36.99More InfoCompare
Jet BoardPrice: $15.99More InfoCompare
Jet WrenchMore InfoCompare
Wehrs Machine WM47 Carburetor FeetMore InfoCompare
Holley 20-124 Universal Carburetor Installation KitPrice: $19.99More InfoCompare
Holley 36-117 Carburetor Small Gasket & Plug KitPrice: $153.99More InfoCompare
Holley 36-118 Carburetor Hardware Parts KitPrice: $153.99More InfoCompare
Holley 36-184 Accelerator Pump Tuning KitPrice: $137.99More InfoCompare
This 2-in-1 float adjusting tool has both a 5/8" socket and straight blade screwdriver to make float adjustment a snap.
Protects and keeps 88 Holley jets in order. Threaded front and back. Anodized alum.
No need to remove your carburetor or distributor to handle jet replacement, with Speedway Motors' Holley Jet Wrench!
Speedway has been racing for more than 50 years, and saw the need for a handy wrench to make Holley rear jet replacement easier. The wrench's precision designed tip fits snugly into the jets. Poor fitting and misaligned screwdrivers can cause external jet damage and affect fuel flow.
The short size and 90-degree end provides just the angle needed to properly loosen and snug jets into place, while easily working between the distributor and carb. The opposite end of the wrench is designed to handle bowl screw removal, opening the gas level plug, as well as float screw adjustment.
Bolt to the base of your carburetor so you can work on it without damaging the throttle assembly.
- 5/16”-18 threads
- 1-1/2” tall
- Set of 4 (nuts included)
The kit contains all the hardware necessary for most installations of a new 4 bbl carburetor including: mounting studs (including an extra long one for securing throttle cable / kickdown cable brackets), washers, nuts, air cleaner stud, vacuum caps, 3 different throttle cable balls, bushing adapter for large hole of throttle lever, air cleaner gasket and base gaskets for square and spread bore carbs.
- Contains most commonly needed hardware for installation of a new carb
- Fits virtually all makes and models of 4 bbl square and spread bore carburetors
This kit consists of various small gaskets, plugs and seals for transfer tubes, power valves, vacuum secondary housing, needle and seat hardware and pump discharge nozzles.
This kit consists of carburetor hardware components such as throttle shaft bushings, idle needles, check balls, rods, retainers, screws and plugs.
This tuning kit is composed of a selection of accelerator pump hardware components including pump diaphragms, pump nozzles, pump cams and related parts. Contained in a convenient plastic parts case, this kit has all that is required to properly tune and calibrate the accelerator pump circuit(s) for your street, drag or circle track car or tow vehicle. A handy parts guide is affixed to the inside case cover to assist in reordering components when necessary.