Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Large Image
CLOSE [X]

Hagan Street Rods fm4SSR-LEDH Flush Mount Tail Lights Red Slot 4 x .5

Price:
$194.99
PR
In Stock
Item #:
91039047
Hagan Street Rods fm4SSR-LEDH Flush Mount Tail Lights Red Slot 4 x .5
Click image to enlarge Click image to enlarge
No video at this time.
 

Hagan has made it simple to add a set of flush mount LED tail lights to your street rod or custom. This complete kit includes lenses, boxes, LED lights, wiring, seals, mounting hardware, and a detailed instruction sheet on how to install step by step.

  • Installs in curved or flat surfaces, in steel or fiberglass vehicles
  • Designed to be sanded down to match the contour of your panel
  • Lenses are 4" x 0.5" x 0.25" thick
  • Steel face plate is 18 gauge mild steel

To make your flasher work you may have to add a dummy load resister. A dummy load resister is used to increase the amps drawn by the LED to make the flasher operate.

 

Instructions, Part 1 (PDF)

Instructions, Part 2 (PDF)

Email this page
Close [x]
You can send this product by email to a friend!
Enter the required information in the spaces provided below. They will receive an Email with the picture of this product and a link back to our site.
Your Name:
Your Email:
Friends Name:
Friends Email:
Print Page
You May Also Be Interested In...
  • Hagan Dummy Load Resistors for LED Lights
    Hagan Dummy Load Resistors for LED Lights
    (1 Rating)
    Price: $9.99
    More Info
    Hagan Dummy Load Resistors for LED Lights
    x 
    							                        
    
                                                        
    When installing LED lights, you may need to use a dummy load resistor to increase the amps drawn by the LED on the turn signal flasher to make it work properly.
    • Increase the amps drawn by the LED 
    • Turn signal flasher 
    • 12 Volt source
    • The dummy loads should be installed parallel, with one LED turn/hazard bulb on each side.
    • Simply splice the dummy load into the power wire for the LED and a good ground source.
      • This must be done for one lamp on each side of the vehicle.
    Instructions (PDF)
  • Hagan Street Rods fm4SSA-LEDH Flush Mount Tail Lights Amber Slot 4x.5
    Hagan Street Rods fm4SSA-LEDH Flush Mount Tail Lights Amber Slot 4x.5
    Price: $194.99
    More Info
    Hagan Street Rods fm4SSA-LEDH Flush Mount Tail Lights Amber Slot 4x.5
    x 
    							                        
    
                                                        
    Hagan has made it simple to add a set of flush mount LED tail lights   to your street rod or custom. This complete kit includes lenses, boxes,   LED lights, wiring, seals, mounting hardware, and a detailed  instruction  sheet on how to install step by step.
    • Installs in curved or flat surfaces, in steel or fiberglass vehicles
    • Designed to be sanded down to match the contour of your panel
    • Lenses are 4" x 0.5" x 0.25" thick
    • Steel face plate is 18 gauge mild steel 
       To make your flasher work you may have to add a dummy load resister. A   dummy load resister is used to increase the amps drawn by the LED to   make the flasher operate.
     
    Instructions, Part 1 (PDF)
    Instructions, Part 2 (PDF)
  • Hagan Street Rods fm4DSR-LEDH Flush Mount 4 Inch Tail Lights Red Dual
    Hagan Street Rods fm4DSR-LEDH Flush Mount 4 Inch Tail Lights Red Dual
    Price: $199.99
    More Info
    Hagan Street Rods fm4DSR-LEDH Flush Mount 4 Inch Tail Lights Red Dual
    x 
    							                        
    
                                                        
    Hagan has made it simple to add a set of flush mount LED tail lights   to your street rod or custom. This complete kit includes lenses, boxes,   LED lights, wiring, seals, mounting hardware, and a detailed  instruction  sheet on how to install step by step.
    • Installs in curved or flat surfaces, in steel or fiberglass vehicles
    • Designed to be sanded down to match the contour of your panel
    • Lenses are 4" x 0.5" x 0.25" thick
    • Lenses are spaced 0.5" apart
    • Steel face plate is 18 gauge mild steel 
       To make your flasher work you may have to add a dummy load resister. A   dummy load resister is used to increase the amps drawn by the LED to   make the flasher operate.
     
    Instructions, Part 1 (PDF)
    Instructions, Part 2 (PDF)