Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf

Hagan Flush Mount LED Tail Lights Red Oval 4.5 x 1.5

Specs
Overall Height:
1.50
Overall Length:
4.50
Sold in Quantity:
Pair
Overall Thickness:
.25
L.E.D. Color:
Red
Hardware Included:
Yes
Bulb Type:
LED
Lens Material:
Plastic
Garage Sale:
Yes
Hagan Flush Mount LED Tail Lights Red Oval 4.5 x 1.5
Hagan Flush Mount LED Tail Lights Red Oval 4.5 x 1.5

Click image to enlarge

Speeday Motors Logo
X
Hagan Flush Mount LED Tail Lights Red Oval 4.5 x 1.5

Please NOTE the following about this product:

  • This item is sold as a pair.

Details

Reviews

Q & A

What's in the Box

Hagan has made it simple to add a set of flush mount LED tail lights to your street rod or custom. This complete kit includes lenses, boxes, LED lights, wiring, seals, mounting hardware, and a detailed instruction sheet on how to install step by step.

  • Installs in curved or flat surfaces, in steel or fiberglass vehicles
  • Designed to be sanded down to match the contour of your panel
  • Lenses are 4.5" x 1.5" x 0.25" thick
  • Steel face plate is 18 gauge mild steel

To make your flasher work you may have to add a dummy load resister. A dummy load resister is used to increase the amps drawn by the LED to make the flasher operate.

 

Instructions, Part 1 (PDF)

Instructions, Part 2 (PDF)

You may also be interested in:

Hagan Dummy Load Resistors for LED Lights
                        

When installing LED lights, you may need to use a dummy load resistor to increase the amps drawn by the LED on the turn signal flasher to make it work properly.

  • Increase the amps drawn by the LED 
  • Turn signal flasher
  • 12 Volt source
  • The dummy loads should be installed parallel, with one LED turn/hazard bulb on each side.
  • Simply splice the dummy load into the power wire for the LED and a good ground source.
    • This must be done for one lamp on each side of the vehicle.

Instructions (PDF)

Hagan Street Rods fmTD6R-LEDH Flush Mount Tail Lights Teardrop 6 x .75
                        

Hagan has made it simple to add a set of flush mount LED tail lights to your street rod or custom. This complete kit includes lenses, boxes, LED lights, wiring, seals, mounting hardware, and a detailed instruction sheet on how to install step by step.

  • Installs in curved or flat surfaces, in steel or fiberglass vehicles
  • Designed to be sanded down to match the contour of your panel
  • Lenses are 6" x .75" x 0.25" thick
  • Steel face plate is 18 gauge mild steel
  • Boxes are 1-5/8" deep x 2" wide x 9" long

To make your flasher work you may have to add a dummy load resister. A dummy load resister is used to increase the amps drawn by the LED to make the flasher operate.

 

Instructions, Part 1 (PDF)

Instructions, Part 2 (PDF)

Hagan Street Rods fm4SSR-LEDH Flush Mount Tail Lights Red Slot 4 x .5
                        

Hagan has made it simple to add a set of flush mount LED tail lights to your street rod or custom. This complete kit includes lenses, boxes, LED lights, wiring, seals, mounting hardware, and a detailed instruction sheet on how to install step by step.

  • Installs in curved or flat surfaces, in steel or fiberglass vehicles
  • Designed to be sanded down to match the contour of your panel
  • Lenses are 4" x 0.5" x 0.25" thick
  • Steel face plate is 18 gauge mild steel

To make your flasher work you may have to add a dummy load resister. A dummy load resister is used to increase the amps drawn by the LED to make the flasher operate.

 

Instructions, Part 1 (PDF)

Instructions, Part 2 (PDF)

Hagan Street Rods fm4DSR-LEDH Flush Mount 4 Inch Tail Lights Red Dual
                        

Hagan has made it simple to add a set of flush mount LED tail lights to your street rod or custom. This complete kit includes lenses, boxes, LED lights, wiring, seals, mounting hardware, and a detailed instruction sheet on how to install step by step.

  • Installs in curved or flat surfaces, in steel or fiberglass vehicles
  • Designed to be sanded down to match the contour of your panel
  • Lenses are 4" x 0.5" x 0.25" thick
  • Lenses are spaced 0.5" apart
  • Steel face plate is 18 gauge mild steel

To make your flasher work you may have to add a dummy load resister. A dummy load resister is used to increase the amps drawn by the LED to make the flasher operate.

 

Instructions, Part 1 (PDF)

Instructions, Part 2 (PDF)